MINOURA W-3100 Instruction Manual

Tool Tray (option) Back Knob Clutch Release Lever Upper Pillar Lower Frame Right Side Leg Adjusting Screw Clamp Adjust Knob Clamp Lever Clamp Jaws Gear Clutch Upper Pillar Holding Bolt Lock Bolt PARTS NAME Left Side Leg HOW TO ASSEMBLE W-3100 Required Tools: 1 x 13mm Spanner 1 x 6mm Hex Wrench 1 x 5mm Hex Wrench Assemble both Legs to the Lower Frame with the supplied M8x40 bolts and M8 Nylon Nuts. M8x40 Cap Bolt M8 Nylon nut 1

and check if every Adjusting Screw is touching the floor perfectly. If not, adjust the length of the Adjusting Screw then tighten the lock nut firmly by a 13mm spanner. This is very important to keep enough stability while your bike is on the stand. 13mm spanner 3 Assemble the clamp jaw unit to the Upper Pillar. The Back Knob should be tightened as firmly as possible until the clamp jaws rotates smoothly. 4 Insert the assembled Upper Pillar into the Lower Frame until the bottom cut-outs catch the Upper Pillar Holding Bolt, then tighten the Lock Bolt firmly by a 5mm hex wrench. To install the optional Tool Tray, insert the tray into the Upper Pillar BEFORE assembling the frames. Fix the position, then tighten the knob bolt. Lock Bolt

Pull down the Clamp Lever to open the jaws. 1 2 Place the top frame or the seat pillar onto the lower jaw, then fully pull up the Clamp Lever to close the jaws. 3 Turn the Clamp Adjust Knob clockwise to securely hold the bike. Turning counter-clockwise will widen the opening. 4 To rotate the clamp jaws, push down the Clutch Release Lever then rotate the jaws. Release your finger after confirming the ratch is securely engaged to the gear. ABOUT OUR WARRANTY PROGRAM You are covered under our warranty program for maximum 5 years from the date of your purchase. Any defects caused by the manufacturer's mistake will be solved with this program at manufacturer's expense, but any problem caused by the user's misuse or natural worn will not be supported by this program. Minoura does not owe any responsibility to any extra troubles these problems may bring. For more detail, refer the attached "MINOURA LIMITED WARRANTY POLICY" card in the package. (Maximum Load Capacity: 40 kgs / 90 lbs) CONTACT INFORMATION MINOURA NORTH AMERICA MINOURA JAPAN HEADQUARTERS (for U.S. residents only) (for all other customers) 1996 East Ave. Hayward, CA 94541 U.S.A. 1197-1 Godo, Anpachi, Gifu 503-2305 Japan Phone: 1-510-538-8599 Fax: 81-584-27-7505 Fax: 1-510-538-5899 Email: [email protected] Email: [email protected] Web: www.minoura.jp MADE IN JAPAN

C-3 C-4 C-11 C-6 C-7 C-8 P-4 P-3 C-9 C-10 C-11 P-1 T-4 T-2 P-5 P-8 P-9 L-9 L-3 L-4 L-3 L-4 L-10 L-11 P-7 P-7 C-4 L-11 C-3: Clamp Rubber C-4: Lock Clip C-6: Clamp Shaft C-7: Clutch Packing C-8: Clamp Space Collar C-9: M8 Flat Washer C-10: Back Knob C-11: Clamp Jaws Assy P-1: Upper Pillar P-3: Clutch Release Lever P-4: Pivot Screw P-5: Pillar Cap P-7: Upper Pillar Holding Bolt & Nut P-8: Lock Bolt P-9: Lower Frame L-3: Leg End Cap L-4: Adjusting Screw L-9: Left Side Leg L-10: Right Side Leg L-11: M8x40 Bolt & M8 Nylon Nut T-2: Tray Fixing Knob Bolt T-4: Tool Tray w/ tool slots