Murray 425014x92B Instruction Book

the product information is included with the unit. This information includes the INSTRUCTION BOOKS, the REPLACEMENT PARTS and the WARRANTIES. This information must be included to make sure state laws and other laws are followed. PRODUCT INFORMATION This Instruction Book contains information for several models. Read and keep this book for future reference. This book contains important information on SAFETY, ASSEMBLY, OPERATION, AND MAINTENANCE. RECORD THE FOLLOWING INFORMATION ABOUT YOUR UNIT. THIS INFORMATION IS NECESSARY WHEN ORDERING PARTS OR IN CASE OF LOSS OR THEFT. F-050706L Model 425014x92B

WARRANTY 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . RESPONSIBILITY OF THE OWNER 3 . . . . . . . . . . . . . . . . . . . . SAFETY RULES 3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . INTERNATIONAL PICTORIALS 9 . . . . . . . . . . . . . . . . . . . . . . . . ASSEMBLY 10 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . PARTS BAG - CONTENTS 10 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . HOW TO INSTALL THE SEAT 11 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . HOW TO ASSEMBLE THE STEERING WHEEL 11 . . . . . . . . . . . . . HOW TO ASSEMBLE THE GAUGE WHEELS 12 . . . . . . . . . . . . . . . MAINTENANCE FREE BATTERY 12 . . . . . . . . . . . . . . . . . . . . . . . . . . HOW TO INSTALL THE BATTERY CABLES 12 . . . . . . . . . . . . . . . . HOW TO PREPARE THE ENGINE 13 . . . . . . . . . . . . . . . . . . . . . . . . . CHECK THE TIRES 13 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . CHECK THE LEVEL OF THE MOWER HOUSING 13 . . . . . . . . . . . OPERATION 14 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . LOCATION OF CONTROLS 14 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ATTACHMENTS 15 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ELECTRICAL SAFETY SYSTEM 15 . . . . . . . . . . . . . . . . . . . . . . . . . . HOW TO OPERATE THE IGNITION KEY SWITCH 15 . . . . . . . . . . HOW TO USE THE THROTTLE CONTROL 15 . . . . . . . . . . . . . . . . . HOW TO USE THE BLADE ROTATION CONTROL 16 . . . . . . . . . . HOW TO USE THE SHIFT LEVER 16 . . . . . . . . . . . . . . . . . . . . . . . . . HOW TO SET THE PARKING BRAKE 17 . . . . . . . . . . . . . . . . . . . . . . HOW TO CHANGE THE CUTTING HEIGHT 17 . . . . . . . . . . . . . . . . . HOW TO STOP THE UNIT 17 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . HOW TO TRANSPORT THE UNIT 17 . . . . . . . . . . . . . . . . . . . . . . . . . HOW TO OPERATE WITH THE MOWER HOUSING 18 . . . . . . . . . HOW TO OPERATE THE UNIT ON HILLS 18 . . . . . . . . . . . . . . . . . . BEFORE STARTING THE ENGINE 19 . . . . . . . . . . . . . . . . . . . . . . . . HOW TO START THE ENGINE 19 . . . . . . . . . . . . . . . . . . . . . . . . . . . . OPERATING TIPS 20 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . MOWING AND BAGGING TIPS 20 . . . . . . . . . . . . . . . . . . . . . . . . . . . MAINTENANCE 21 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . MAINTENANCE CHART 21 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . HOW TO CHECK THE MUFFLER 21 . . . . . . . . . . . . . . . . . . . . . . . . . HOW TO REMOVE AND INSTALL THE BLADE 22 . . . . . . . . . . . . . HOW TO SHARPEN THE BLADE 22 . . . . . . . . . . . . . . . . . . . . . . . . . HOW TO ADJUST THE BLADE ROTATION CONTROL 23 . . . . . . HOW TO CHECK AND ADJUST THE DRIVE BRAKE 24 . . . . . . . . HOW TO CHECK AND ADJUST THE CLUTCH 24 . . . . . . . . . . . . . . HOW TO ADJUST THE SHIFT LEVER 25 . . . . . . . . . . . . . . . . . . . . . MAINTENANCE FREE BATTERY 25 . . . . . . . . . . . . . . . . . . . . . . . . . . HOW TO CHARGE THE BATTERY 25 . . . . . . . . . . . . . . . . . . . . . . . . WHERE TO LUBRICATE 26 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . HOW TO CHECK THE FUEL FILTER 26 . . . . . . . . . . . . . . . . . . . . . . CHECK THE TIRES 26 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . HOW TO REMOVE THE MOWER HOUSING 27 . . . . . . . . . . . . . . . . HOW TO INSTALL THE MOWER HOUSING 27 . . . . . . . . . . . . . . . . HOW TO ADJUST THE GAUGE WHEELS 28 . . . . . . . . . . . . . . . . . . HOW TO LEVEL THE MOWER HOUSING 29 . . . . . . . . . . . . . . . . . . HOW TO REPLACE THE MOTION DRIVE BELT 30 . . . . . . . . . . . . HOW TO REPLACE THE MOWER DRIVE BELT 32 . . . . . . . . . . . . . HOW TO INSTALL THE WHEELS 33 . . . . . . . . . . . . . . . . . . . . . . . . . HOW TO REPLACE THE FUSE 34 . . . . . . . . . . . . . . . . . . . . . . . . . . . HOW TO REPLACE THE LIGHT BULB 34 . . . . . . . . . . . . . . . . . . . . . HOW TO CLEAN THE MOWER HOUSING 34 . . . . . . . . . . . . . . . . . . STORAGE (OVER 30 DAYS) 34 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . TROUBLE SHOOTING CHART 35 . . . . . . . . . . . . . . . . . . . . . . . . HOW TO ORDER REPAIR PARTS 36 . . . . . . . . . . . . . . . . . . . . . . PARTS LIST 38 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . SLOPE GUIDE 54 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . INDEX 55 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . LAWN TRACTOR ACCESSORIES 56 . . . . . . . . . . . . . . . . . . . . . MURRAY, INC. Two Year Limited Warranty Murray, Inc. warrants to the original purchaser that this unit shall be free from defects in material and workmanship under normal use and service for a period of Two (2) Years from the date of purchase; however, this warranty does not cover engines, accessories (such as snow blowers, snow blades, grass baggers and plows), transmissions, batteries and Normal Wear Parts (except as noted below) or transaxles as the companies that manufacture these items furnish their own warranties and provide service through their authorized field service facilities. For additional information, see the warranties covering these particular parts. If you are uncertain whether your unit contains or is equipped with one or more of these parts, consult your dealer prior to purchase. Subject to the terms and conditions noted in this Limited Warranty, we shall, at our option, repair or replace at no cost to the original purchaser any part covered by this Limited Warranty during the applicable warranty period. In the event the battery proves defective within ninety (90) days from the date of purchase, we will replace it without charge. If the battery proves defective after (90) days but within one hundred twenty (120) days from the date of purchase, we will replace it for a charge of one half (1/2) of the retail price of the battery in effect at the time of return. Normal Wear Parts are defined as belts, blades, blade adapters, pneumatic tires, headlights and seat covers. These parts are warranted to be free from defects in material and workmanship as delivered with the product. Any claim for repair or replacement of Normal Wear Parts must be made within thirty (30) days of the date of purchase. No claims involving damage caused from material use, abuse or misuse will be honored. This Murray, Inc. Two (2) Year Limited Warranty is your exclusive remedy; however, this warranty is void or does not apply to any unit that has been tampered with, altered, misused, abused or used for rental or other commercial and/or professional (non-homeowner) uses. Your warranty does not cover minor mechanical adjustments which are not due to any defect in material or workmanship. For assistance in making such adjustments, consult your Instruction Book. To make a claim under this Murray, Inc. Two (2) Year Limited Warranty, return the unit (or if authorized in advance, the defective part) along with your proof of purchase to an Authorized Service Center near you. To locate the nearest Authorized Service Center, call the Central Parts Distributor for your area shown in the list provided with your unit or check the Yellow Page listings in your local telephone directory. If you return the entire unit, we will repair the unit. If we authorize the return of the defective part only, we will either replace or repair the part. In the case of a defect in a transmission or differential (as distinguished from a transaxle), the entire transmission or differential must be returned since they do not include user serviceable parts. This Murray, Inc. Two (2) Year Limited Warranty gives you specific legal rights, and you may also have other rights which vary from state to state. This Limited Warranty is given in lieu of all other expressed and implied warranties including the implied warranty of merchantability and warranty of fitness for a particular purpose. If you need additional information on this written warranty or assistance in obtaining service, write or call: MURRAY, INC., Outdoor Power Equipment, Customer Service Department, P.O. Box 268, Brentwood, Tennessee 37027. (1-800-224-8940)

are written for a person with some mechanical ability. Like most ser- vice books, not all the steps are described. Steps on how to loosen or tighten fasteners are steps anyone can follow with some mechanical ability. Read and follow these instructions before you use the unit. Know your product: If you understand the unit and how the unit oper- ates, you will get the best performance. As you read this manual, com- pare the illustrations to the unit. Learn the location and the function of the controls. To help prevent an accident, follow the operating instruc- tions and the safety rules. Keep this manual for future reference. IMPORTANT: Many units are not assembled and are sold in car- tons. It is the responsibility of the owner to make sure the assembly instructions in this manual are exactly followed. Other units are pur- chased in an assembled condition. On assembled units, it is the re- sponsibility of the owner to make sure the unit is correctly assembled. The owner must carefully check the unit according to the instructions in this manual before it is first used. Engine Exhaust, some of its constituents, and certain vehicle components contain or emit chemicals known to the State of California to cause cancer and birth defects or other repro- ductive harm. Battery posts, terminals and related accesso- ries contain lead and lead compounds, chemi- cals known to the State of California to cause cancer and birth defects or other reproductive harm. WASH HANDS AFTER HANDLING. RESPONSIBILITY OF THE OWNER The responsibility of the owner is to follow the instructions below. 1. Carefully read and follow the rules for safe operation. 2. Follow all the assembly instructions. 3. Inspect the unit. 4. Make sure that the operator of the unit knows how to correctly use all standard and accessory equipment. 5. Operate the unit only with guards, shields, and other safety items in place and working correctly. 6. Correctly adjust the unit. 7. Service the unit only with authorized or approved replacement parts. 8. Complete all maintenance on the unit. Environmental Awareness � Do not fill the engine’s fuel tank completely full. � Drain fuel for off-season storage. � Use only unleaded gasoline. � Service the air cleaner regularly. � Change oil regularly. Use 10W-30 oil in summer. � Tune-up the engine regularly. � Keep equipment in efficient operating condition. � Dispose of used engine oil properly. SAFETY RULES Safe Operation Practices for Ride-on Mowers WARNING: This cutting machine is capable of amputating hands and feet and throwing objects. Failure to observe the following safety instructions could result in serious injury or death. I. General operation 1. Read, understand and follow all instructions in the Instruction Book, on the machine, the engine and with any attachments before starting. 2. Only allow responsible adults, who are familiar with the instructions, to operate the machine. 3. Clear the area of objects such as rocks, toys, wire, etc., which could be picked up and thrown by the blade. 4. Be sure the area is clear of other people before mowing. Stop the machine if anyone enters the area. 5. Never carry passengers. 6. Turn off power to the blades or any attachments before backing up. Do not mow in reverse unless absolutely necessary. Always look down and behind before and while backing. 7. Be aware of the mower discharge direction and do not point it at anyone. Do not operate the mower without either the entire grass bagger or the mower guard in place. 8. Slow down before turning. 9. Never leave a machine unattended with the engine running. Always turn off the blade(s), set the parking brake, stop the engine and remove the key before dismounting. 10. Turn off power to attachment(s) when transporting or not in use. Turn off the blade(s) when not mowing. 11. Stop the engine before removing the grass bagger or unclogging the chute. 12. Mow only in daylight or good artificial light. 13. Do not operate the machine while under the influence of alcohol or drugs or when very tired. 14. Watch for traffic when operating near or crossing roadways. 15. Use extra caution when loading or unloading the machine into a trailer or truck. 16. Always wear goggles, safety glasses, or an eye shield when you operate the unit to protect your eyes from foreign objects that can be thrown from the unit. Always wear eye protection when you make an adjustment or repair to the machine. 17. Use care when pulling loads or using heavy equipment. a. Use only approved drawbar hitch points. b. Limit loads to those you can safely control.

d. Use counterweights or wheel weights when suggested in the Instruction Book. 18. Do not operate this machine if you are taking drugs or other medication which can cause drowsiness or affect your ability to operate this machine. 19. Do not use this machine if you are mentally or physically unable to operate this machine safely. 20. Data indicates that operators, age 60 years and above, are involved in a large percentage of riding mower related injuries. These opera- tors should evaluate their ability to operate a riding mower safely enough to protect themselves and others from serious injury. II. Slope operation Slopes and rough terrain are major factors related to loss-of-control and tip-over accidents, which can result in severe injury or death. ALL slopes require extra caution. If you cannot back up the slope or if you feel uneasy on the slope, do not mow it. See the “Slope Guide” in the back of this book to check for safe operation. DO 1. Mow up and down slopes, not across. 2. Remove obstacles such as rocks, limbs, etc... 3. Watch for holes, ruts or bumps. Uneven terrain could overturn the machine. Tall grass can hide obstacles. 4. Follow the manufacturer’s recommendations for wheel weights or counterweights to improve stability. 5. Use extra care with grass baggers or other attachments, they can change the stability of the machine. 6. Keep all movement on the slopes slow and gradual. Do not make sudden changes in speed or direction. 7. Avoid starting or stopping on a slope. If tires lose traction, turn off the blades and proceed slowly straight down the slope. DO NOT 1. Do not turn on slopes unless absolutely necessary, then only turn slowly and gradually downhill, if possible. 2. Do not mow drop-offs, ditches or embankments. A wheel over the edge or an edge caving in could cause a sudden overturn and an injury or death. 3. Do not mow on wet grass. Reduced traction could cause sliding. 4. Do not try to stabilize the machine by putting your foot on the ground. 5. Do not use a grass bagger or other rear mounted accessories on steep slopes (greater than 10 degrees). III. Children Tragic accidents can occur if the operator is not alert to the presence of children. Children are often attracted to the machine and the mowing activity. NEVER assume that children will remain where you last saw them. 1. Keep children out of the mowing area and in the watchful care of another responsible adult. 2. Be alert and turn the engine off if children enter the area. 3. Before and when backing, look behind and down for small children. 4. Never carry children or any passengers, even with the blades off. They may fall off and be seriously injured or interfere with the safe operation of the machine. 5. Never allow children to operate the machine. Instruct children in the potential dangers of the machine. 6. Use extra care when approaching blind corners, shrubs, trees or other objects that may obscure vision. IV. Service 1. Use extra care when handling gasoline and other fuels. Fuels are flammable and the vapors are explosive. a. Use only an approved container. b. Never remove the gas cap or add fuel with the engine running. Allow the engine to cool for several minutes before refueling. Do not smoke. c. Never refuel the machine indoors. d. Never store the machine with fuel in the tank or fuel container inside where there is an open flame, such as a water heater. 2. Never start or run the engine inside a closed area. 3. Keep all nuts and bolts, especially the blade attachment nuts tight. Frequently check the blade(s) for wear or damage such as cracks and nicks. A blade that is bent or damaged must be immediately replaced with an original equipment blade from an authorized service dealer. For safety, replace the blade every two years. Keep the equipment in good condition. 4. Never tamper with the safety devices. Check their proper operation regularly. 5. To reduce fire hazards, keep the machine free of grass, leaves or other debris build-up. Clean up oil or fuel spills. Allow the machine to cool before storing. 6. Stop and inspect the equipment if you strike an object. Repair, if necessary, before restarting. 7. Never make adjustments or repairs with the engine running. The carburetor can be adjusted with the engine running. Do not change the engine governor settings or over-speed the engine. 8. Grass bagger components are subject to wear, damage and deterioration, which could expose moving parts or allow objects to be thrown. For storage, always make sure the grass bag is empty. Frequently check components and replace with manufacturer’s recom- mended parts when necessary. 9. Mower blade(s) are sharp and can cut. Wrap the blade(s) or wear gloves and use extra caution when servicing them or the blade housing area. 10. Check the brake operation frequently. Adjust and service as required. 11. Wait for all movement to stop before servicing any part of the unit. Look for this symbol to indicate important safety precautions. This symbol indicates: “Attention! Become Alert! Your Safety Is At Risk.”

5 F-050706L Each person that operates power equipment must learn to use correct and safe mowing procedures. To help you learn, carefully read the following pages. Most of the time the operator was not correctly shown or did not read the instructions on the unit or in the Instruction Book before using the unit. Also, some operators do not have enough experience. The result is unsafe use, endangering the operator, bystanders and the equipment. Another result can be a poor appearance of the area mowed. Read this book. Read the instructions on the unit. Operate the mower according to the Safe Mowing Guide. Follow all safety rules, cautions or warnings in this book and on the unit. Make sure anyone that uses the unit reads the instructions and is told how to safely operate the mower. The mower will give you good service and durability, if operated in normal conditions. If the mower is not correctly serviced or is used where the terrain is rough or unsuitable, product performance and safety will be decreased. Correct clothing is an important part of safe mowing. Safety glasses will protect the eyes from objects discharged by the mower. Safety shoes with steel plates can protect a foot from injury by the blade. For protection from objects discharged from the mower, wear clothing that will cover the arms and legs. Before you start cutting the grass, practice using the mower in a large open and level area. Learn the location of the controls on the mower. Know the purpose of the controls and how they work. In an emergency, how fast you can stop the blade is important. Learn how to control the mower at all times. Many engines are started by hand. When you use a pull start or rope start, place your feet apart and away from the blade(s). Hold the rope handle tight. Never wrap the rope around your arm or fingers for a “better grip”. To start the engine, follow the instructions on the mower, in this book and in the engine operating instructions. For electric start engines, sit in the seat to start the engine. The battery can be dangerous. Follow the instructions on the battery, the acid container, and in this book when working with the battery. Even small batteries have enough voltage to cause an injury. Always be careful. The mower is designed to be operated by one person. Never let another person ride with you on the unit or on any accessories. A passenger will make the unit harder to control, block the visibility or distract the operator and is dangerous to the operator, the passenger and the equipment. Without a passenger seat, the passenger can fall from the mower or contact dangerous parts. A mower is not a toy for showing off or for giving rides. Never cut a wet lawn. Wet grass can cause an accident, affect mower performance and can cause problems with future lawn growth and appearance. Wet grass is slippery and can cause the mower to slip. Someone can get injured by touching the blade(s). Wet grass tends to clog the mower, causing poor discharge. Cut wet grass will collect on the lawn, retarding the growth of the grass. Also, getting the mower wet will cause parts to rust and decrease the life of the unit. When you look over the lawn, remember obstacles that cannot be removed, like pipes, stumps or rocks. Keep away from these obstacles that can cause damage to the mower or injury to the operator or a person near the mower. Clear the area of rocks, toys, wire or other loose objects. These items can damage the mower or can be discharged by the mower blade. The blade of a power mower rotates very fast. It can discharge rocks and other objects over a long distance which can be dangerous. The force of the objects can break windows, cause injuries or even put an eye out. Most of the time the injury is to a person, like a child. Keep every person completely away from the area to be mowed. Make sure the grass is not discharged toward anyone. Planning your mowing pattern has a double advantage. It can decrease the possibility of an injury and make the clean up after mowing easier. Check the terrain of the area to be mowed. Mow in a pattern that will keep you away from dangerous areas. Check the distance you need to stop and the distance available to turn. Slopes and rough terrain must be mowed carefully and some areas must not be mowed at all. With riding mowers, mow up and down the hill. When you must mow rough terrain or on slopes, never change directions or change gears and stop in these areas only in an emergency. Before you ride up or down a slope, try to back straight up the slope. Do not ride up or down a slope that is too steep to back straight up. See the “Guide” in the back of this Instruction Book to check any slopes. Before you start cutting, make sure the mower was completely assembled according to the Instruction Book. If the

6 F-050706L mower was completely assembled at the store, you must still check the mower according to the assembly instructions. Make sure the mower is correctly assembled and that all fasteners are tight. Make sure the engine has the correct amount of oil. Check these items often during the life of the mower. Your mower has a gasoline engine. Gasoline is a dangerous fuel. Keep gasoline only in an approved safety gasoline container. Do not keep large amounts of gasoline. When you add gasoline to the fuel tank, do not smoke. Store the gasoline container and the mower in an area that has good ventilation. Also, keep the gasoline away from any flames like the pilot light of a furnace or any other source of ignition. If the mower is to be stored for more than a few weeks, remove the gasoline from the fuel tank. When inside an enclosure, do not add gasoline to the fuel tank. Before you add gasoline, move the mower outside and add gasoline carefully. Before you start the engine, remove any gasoline from the outside of the fuel tank or from the mower. Warm gasoline will expand. Leave some space in the fuel tank for the gasoline to expand. Also, the fuel cap has a vent hole for fuel vapors. Always use the correct fuel cap. Failure to follow safety rules about gasoline will cause fires and explosions, injury to you and damage to the equipment and other property. If you add gasoline to an engine that is running or hot, the result can be an explosion. Before you add gasoline, stop the engine and let the engine cool for several minutes. Remove dry grass and other debris from the mower. Keep the mower clean to improve the performance, help the engine and transmission run cooler, extend the life of moving parts, and decrease the danger of a fire. Fires and explosions are not the only dangers when working around a mower. The engine, transmission, and the muffler will get hot in several minutes when the engine is running. Do not touch these parts of the mower. Stop the engine. Let the engine and transmission cool before servicing the mower. Remember, exhaust fumes are dangerous. Never operate the engine inside a building. When you get a new mower, it can be a new experience for the family. Tell each person how a mower can be dangerous. Remember, a mower is not a toy. A mower is not to be used by children or anyone not old enough, strong enough or that does not have experience. If the mower is not correctly assembled, not operated correctly, or not regularly serviced, the mower can be dangerous. The most important rule to follow is always use good judgement and common sense. Mow safely and carefully. Your mower will easily cut thick grass. Fingers, feet and other parts can also be cut by the blade. Injuries occur when the operator does not think and reaches into the chute opening. Always operate the mower as if the blade is rotating. Do not service or make an adjustment, except to the carburetor, while the engine is running. Use only accessories that are factory approved for your mower. The wrong accessory can decrease the safety of the mower and can even damage the unit. Read and follow the instructions included with the accessory and the mower. Use only original equipment or replacement parts that are factory approved for service. If you need service, select an Authorized Service Center for your mower. If you do the work on the unit, follow the instructions in the Instruction Book. When you mow, remember that children are attracted to the mower. Always use caution when mowing around obstacles like trees or shrubs or when moving backward. Only mow in a forward direction if possible. Your visibility is decreased when you mow backward. Also, the blades are made to cut while the unit is moving forward. If you mow backward, the cutting performance decreases. Before you leave the mower, stop the engine. Remove the key. Disengage and lower any attachment. Set the parking brake. Never mount or dismount from the seat while the engine is running. An accident can occur if you touch the brake, shift lever, throttle, clutch or blade control while the engine is running. Mount and dismount from the seat on the side of the unit that is marked ENTER-EXIT. Make sure you are in good condition when you mow. When you mow for several hours your reflexes will decrease and your mind will not be as alert. Take a short break or an accident can occur. If the temperature is hot, use caution to prevent dehydration. If you are tired, angry or not completely alert, do not operate the mower. If you use alcohol, medication or drugs, do not use the mower or any type of power equipment. Engine speed is a key to safe mowing and to a good looking lawn. The maximum speed of the engine was set at the factory. Do not change the setting of the engine governor. Select the maximum engine and ground speed that is right for the terrain and the height of the grass. The blade cuts best when the engine is operating at maximum speed. The engine and transmission will also run cooler at maximum engine speed.

7 F-050706L Also, the grass bagger will function better when the engine is operating at maximum speed. On slopes, decrease the ground speed and use care making sure the mower feels safe to operate. If the weather conditions are bad, do not mow. If weather conditions become bad, stop cutting and finish later. It is dangerous to cut grass in the rain. Always find protection in an electrical storm. If the weather conditions are extra dry, protect your eyes with safety glasses from the dust and from the objects discharged by the mower. Also, a dust or a pollen mask can help. Your mower is equipped with a number of safety devices which are important to the safety of the operator and bystanders and must never be changed or removed from the mower. If a safety device is lost, damaged or no longer functions, repair or replace the device before you operate the mower. It is best to mow during the day. If you must mow at night, make sure there is enough light for safe operation. Your mower will require regular maintenance and service. The maintenance schedule depends on the hours of use. Also, mowing conditions can change the schedule. Check the Instruction Book for more information. Correct maintenance will help the mower function safely. Do not service the mower (except for the carburetor adjustment) while the engine is running. Before you service the unit, even with the engine stopped, always disconnect the wire from the spark plug to prevent the engine from starting. If you hit a large object during operation, stop the engine. Remove the wire from the spark plug. Carefully inspect the mower for damage. Before you start the engine again, make the necessary repairs. If you feel new or excessive vibration, immediately stop the engine and check for the problem. Vibration can be a warning of a problem. Keep all nuts, bolts and screws tight. The blade is the most dangerous part of the mower. Frequently check the blade and the blade mounting fasteners. Keep the fasteners tight. If the blade hits a solid object, stop the engine. Remove the wire from the spark plug. Check for a blade that is bent, cracked or for other damages. Before you start the engine, replace a damaged blade(s). For safety, replace the blade every two years. A sharp blade decreases the workload on the engine and more evenly cuts grass. Frequently sharpen the blade for a better looking cut. Use the left side of the mower housing to trim near an object. A grass bagger is a good accessory for your mower. For best performance and safety, make sure the grass bagger is approved for use with your mower. Follow the assembly and operation instructions included with the grass bagger. Some grass baggers require a special blade for best performance. Before you attach, check, or empty the grass bagger, always stop the engine. Before each use of the grass bagger, check for cracks, wear or deterioration. Before you use the grass bagger, replace a damaged part with a replacement part approved by the factory. For you to have a good green lawn, follow the mowing procedures below. Do not cut the grass too short. If you cut the grass too short you can cause the grass to become yellow or make the lawn look brown. Use a lower height of cut in cool months when the grass is thicker. Raise the height of cut in hot dry periods. If you cut the grass with a blade that is not sharp or at a slow engine speed you can damage the grass. Move the throttle control to the FAST position when mowing and using the grass bagger. Also, use a slower ground speed when using the grass bagger. If you change the direction or pattern of cut slightly every time you mow will make the grass grow stronger and thicker. Do not add oil or gasoline to the mower while on the lawn. Spilled oil or gasoline can kill the grass. In high or thick grass, do not try to cut all the grass the first time. Raise the height of cut on the first cutting and lower the height for the next cutting. Another way is to cut only part of the width of the mower and decrease your ground speed (not the engine) to move more slowly so that the mower can discharge the grass as it moves forward. Understand the controls and how they work. Learn the ground speed(s) of your mower. Check the stopping distance required at different travel speeds. Check the turning radius of the mower. The controls on your riding mower are different from an automobile. The throttle is operated by hand and holds the engine speed constant until it is changed. The location of the shift lever and the shift pattern is different from that of an automobile. Also, the brake and clutch systems are different. Remember the procedures to follow in an emergency. Remember, turning off the engine ignition switch will stop the blade and the drive mechanism. If the traction of the wheels is lost or does not feel safe, disengage all systems and stop the engine. Dismount from the mower. Push the unit to a safe place before you begin mowing again. Your unit has an electrical system that includes an operator presence switch in the seat. The operator presence switch detects if the operator is sitting on the seat. The engine will stop if the operator leaves the seat when the blade engagement control is engaged. This operator presence switch is a safety device only. It must not regularly be used to stop the engine or the blade. There are other control systems on the mower for this purpose. Always keep the operator presence switch and other safety devices and controls in place and operating for your protection. Remember, your mower is a tool that can be dangerous if it is not correctly used. Follow the instructions in this Instruction Book. Safe and careful use of the mower will give you many safe hours of problem free use.

8 F-050706L BEFORE MOWING � Be sure to dress correctly. Wear hard shoes, not sandals or tennis shoes. � Examine the blade. A blade that is bent, cracked, or damaged must be replaced with a factory replacement blade. � Fill the fuel tank outside. Clean off spilled fuel. � Read and follow the Owner’s Manual, the instructions with the engine, and the instructions with any attachments. Owner’s Manual instructions are for your safety and the safety of others. � Exhaust fumes are dangerous. Start the engine outside. � Make sure all safety devices are in place and working correctly. � Operation of the mower is only for a person that has experience. � Wet grass can be dangerous. Let the grass dry. � Clear children and others from the property and instruct them to stay away. � Never cut the grass without good light. � Pick up loose objects. Remove them from the mowing area. WHILE MOWING � Do not allow children and others in the mowing area. Watch for children and others. � Watch for fixed objects and avoid them. They can damage the mower or cause injury. � A hot engine, muffler, and transmission will cause a burn. Do not touch. � Inclines and slopes must be carefully mowed. See the “Guide” in the back of this book to check a slope. � Lack of daylight or good artificial light is cause to stop mowing. � Examine the mower, the blade, and other parts for damage after hitting a foreign object or if the unit vibrates excessively. � Do not make adjustments or repairs without stopping the engine. Disconnect the spark plug wire. � On or near roads, watch out for traffic. Direct discharge away from roads. � When mowing, avoid areas where traction is unsure. Look back before changing direction of travel. Look down and behind before and while backing. � In heavy grass, raise the cutting height. Cut slower. Stop the engine to remove clogged grass from the mower. � Never remove any safety related parts. � Do not pour gasoline into a engine that is hot or running. AFTER MOWING � Always let the mower cool before storing in an enclosed area. � Foreign material on the mower is dangerous. Clean off grass, leaves, grease and oil before storing. � Tighten all loose nuts, bolts and screws before you use the unit. � Empty and clean any grass catcher or other accessory. � Remove the key or disconnect the spark plug wire to prevent unauthorized use. � Make sure the mower is not kept near a source of ignition. Gas fumes can cause an explosion. � Only original parts or factory approved substitutes can be used to service the mower. � When storing the mower for an extended period, remove the fuel from the fuel tank. � Instruct children to leave the mower alone. It is not a toy. � Never keep gasoline near a source of ignition. Always use an approved container. Keep gasoline away from children. � Lubricate according to the Instruction Book. See “Lubrication”. IMPORTANT--Read the Instruction Book. Keep this book for future use and reference. WARNING: Look for this symbol to point out important safety precautions. It means: “Attention! Become Alert! Your Safety Is Involved.”

torials are located on your unit or on literature supplied with the product. Be- fore you operate the unit, learn and un- derstand the purpose for each pictorial. Safety Warning Pictorials 1 Warning 2 Shield Eyes. Explosive Gases Can Cause Blindness Or Injury. 3 No Sparks, Flames or Smoking. 4 Sulphuric Acid Can Cause Blindness Or Severe Burns 5 Flush Eyes Immediately With Water. Get Medical Help Fast. 6 IMPORTANT: Read Owner’s Manual Before Operating This Machine. 7 WARNING: Thrown Objects. Keep Bystanders Away. Read User Instructions Before Operating This Machine. 8 WARNING: Do Not Use This Machine On Slopes Greater Than 15 Degrees. 9 DANGER: Keep People, Especially Children, Away From Unit. 10 DANGER: No Step. 11 DANGER: Keep Feet And Hands Away From Rotating Blade. 12 DANGER: Keep Hands Away From Rotating Blade. 13 DANGER: Disconnect Spark Plug Wire Before Servicing Unit. 14 WARNING: Hot Surface. 15 WARNING: Use Caution When Connecting Or Disconnecting Accessories. 16 WARNING: Crushed Fingers. MAX 90N + MAX 150N + 1 2 3 5 4 6 7 8 9 10 12 11 13 14 15 16 1 Control And Operating Pictorials 1 Engine Start 2 Engine Stop 3 Select Reverse 4 Engine Run 5 Brake 6 Parking Brake 7 Clutch 8 Slow 9 Fast 10 Choke 11 Oil 12 Blade Rotation Control 13 Raise 14 Fuel 1 2 4 5 6 7 8 9 10 11 12 13 14 2 3

ries are not included on all models. Read and follow the assembly and adjustment instructions for your mower. All fasteners are in the parts bag. Do not discard any parts or material until the unit is assembled. WARNING: Before doing any assembly or mainte- nance to the mower, remove the wire from the spark plug. NOTE: In this instruction book, left and right describe the loca- tion of a part with the operator on the seat. PARTS BAG - CONTENTS The fasteners and other loose parts are shown below. The fasteners are shown full size. The quantity is shown in brackets ( ). 2x82 (2) Carriage Bolt 14x79 (2) Wing Nut 17x47 (2) Washer 20729 (1) Keys & Ring 1001054 (2) Knob 17x91 (4) Washer 31x11 (2) Locking Ring

Use the fasteners shown below to install the seat. The fasteners are shown at full size. (A) 1001054 (B) 17x47 1. Carefully remove the plastic bag from the seat. 2. Align the holes in the seat hinge to the holes in the seat (Figure 1). Fasten the seat to the seat hinge with the fasteners as shown. 3. Check the operating position of the seat. If the seat needs to be adjusted, loosen the two wing bolts. Slide the seat forward or backward along the seat adjusting holes as shown. Tighten the wing bolts (A). Figure 1 Seat Seat Adjusting Hole Seat Hinge A B HOW TO ASSEMBLE THE STEERING WHEEL Fasteners are not required to assemble the steering wheel. Attach the steering wheel as follows: 1. Make sure the front wheels point forward. 2. Look at the hub of the steering wheel. Make sure the locking clip is in place inside the hub. 3. Slide the bellows over the steering post (Figure 2). NOTE: Before attachment of the steering wheel, make sure that the front wheels point forward and are straight. For proper alignment of the steering wheel, see Figure 2. 4. Slide the steering wheel onto the steering post. Push on the steering wheel. The steering wheel will lock onto the steering post. Pull on the steering wheel. Make sure the steering wheel is locked in place. 5. Attach the cover to the steering wheel. 6. Some models have an optional decal in the parts bag. Attach the decal to the center of the steering wheel as shown. Steering Wheel Cover Steering Post Bellows Decal (Optional) Figure 2 Straight

Use the fasteners shown below to install the gauge wheels. The fasteners are shown at full size. (A) 31x11 (B) 17x91 1. Attach the gauge wheels to the axle bolts with the fasteners. NOTE: The axle bolt is mounted in the LOW position. To change the position to a higher cutting position, see “How To Adjust The Gauge Wheels” in the Maintenance section. Gauge Wheel Figure 3 Axle Bolt A B MAINTENANCE FREE BATTERY IMPORTANT: Before you attach the battery cables to the battery, check the battery date. The battery date tells if the battery must be charged. 1. Check the top and the side of the battery for the location of the battery date (Figure 4). 2. If the battery is put into service before the battery date, the battery cables can be attached without charging the battery. See “How To Install The Battery Cables”. 3. If the battery is put into service after the battery date, the battery must be charged. See “How To Charge The Maintenance Free Battery”. HOW TO CHARGE THE MAINTENANCE FREE BATTERY WARNING: When you charge the battery, do not smoke. Keep the battery away from any sparks. The fumes from the battery acid can cause an explosion. 1. Remove the battery and battery tray. 2. Remove the protective cap from the battery terminal. 3. Use a 12 volt battery charger to charge the battery. Charge at a rate of 6 amperes for one hour. If you do not have a battery charger, have an authorized service center charge the battery. 4. Install the battery and battery tray. Make sure the positive (+) terminal is on the left side. HOW TO INSTALL THE BATTERY CABLES WARNING: To prevent sparks, fasten the red cable to the positive (+) terminal before you connect the black cable. Use the fasteners shown below to install the battery cables. The fasteners are shown at full size. (B) 14x79 (A) 2x82 1. Remove the protective cap from the battery terminal. 2. Fasten the red cable to the positive (+) terminal with the fasteners as shown (Figure 4). 3. Fasten the black cable to the negative (-) terminal with the fasteners as shown. B A Positive (+) Terminal Black Cable Red Cable Battery Tray A Battery Figure 4

� Check the engine oil. � Fill the fuel tank with gasoline. � Check the air pressure of the tires. � Check the level of the mower housing. � Make sure the battery cables are attached. � Make sure the wire is attached to the spark plug. WARNING: Before doing any assembly or mainte- nance to the mower, remove the wire from the spark plug. NOTE: In this instruction book, left and right describe the location of a part with the operator on the seat. HOW TO PREPARE THE ENGINE NOTE: The engine was shipped from the factory filled with oil. Check the level of the oil. Add oil as needed. NOTE: The operation of a new engine will sometimes result in a slight amount of smoke. This smoke is caused by paint or oil on or around the muffler. This is normal and only expected during initial operation. A separate engine manual is also included with the unit. See this engine manual for the manufacturer’s instructions for the type of gasoline and oil to use. Before you use the unit, read the information on safety, operation, maintenance, and storage. WARNING: Follow the engine manufacturer’s instructions for the type of gasoline and oil to use. Always use a safety gasoline container. Do not smoke when adding gasoline to the engine. When inside an enclosure, do not fill with gasoline. Before you add gasoline, stop the engine. Let the engine cool for several minutes. IMPORTANT: This unit is equipped with an internal combustion engine and must not be used on or near any unimproved forest-covered, brush-covered or grass-covered land unless the engine’s exhaust system is equipped with a spark arrester meeting applicable local or state laws (if any). If a spark arrester is used, it must be maintained in effective working order by the operator. In the State of California the above is required by law (Section 4442 of the California Public Resources Code). Other states may have similar laws. Federal laws apply on federal lands. See an Authorized Service Center for a spark arrester for the muffler. In some areas, local law requires the use of a resistor spark plug to control the ignition signals. See an Authorized Service Center for a resistor spark plug for the engine. NOTE: Actual sustained horsepower will likely be lower due to operating limitations and environmental factors. CHECK THE TIRES NOTE: The tires were over inflated for shipment. The correct air pressure is shown on the side of the tire. Check the air pressure in the tires. Tires with too much air pressure will cause the unit to ride rough. Also, the wrong air pressure will keep the mower housing from cutting level. The correct air pressure is shown on the side of the tire. CHECK THE LEVEL OF THE MOWER HOUSING Make sure the level of cut is still correct. After you mow a short distance, look at the area that was cut. If the mower housing does not cut level, see the instructions on “How To Level The Mower Housing” in the Maintenance section of this instruction book.

Pedal Lift Lever Shift Lever LOCATION OF CONTROLS BLADE ROTATION CONTROL: Use the blade rotation control to start and stop the rotation of the blade and also to control various accessories, such as a snow thrower. CLUTCH / BRAKE PEDAL: The pedal has two functions. The first function is a clutch. The second function is a brake. Use the brake pedal to quickly stop the forward or reverse motion of the unit. HEADLIGHT SWITCH: There is not a separate headlight switch. As with many newer automobiles, the headlights are auto- matically on whenever the engine runs. IGNITION KEY SWITCH: Use the ignition key switch to start and stop the engine. When you start the engine and release the ignition key, the ignition key switch will automatically default to the recommended RUN-MOW position for normal mowing. SHIFT LEVER: Use the shift lever to change the speed of the unit. LIFT LEVER: Use the lift lever to change the height of cut. PARKING BRAKE LEVER: Use the parking brake lever to engage the brake when you leave the unit. THROTTLE CONTROL LEVER: Use the throttle control lever to increase or decrease the speed of the engine.

page in this book. This unit can pull attachments like a lawn sweeper, a lawn aerator, a hopper spreader or a small trailer. This unit can not use attachments that engage the ground like a plow, a disk harrow, or a cultivator. For all pull-behind attachments or trailers, the maximum gross weight is 250 pounds. Gross weight is the weight of the attachment or trailer and any load that might be on or in it. Do not operate on a slope that is greater than 10 degrees when using a pull-behind attachment or trailer. We have included a slope guide in this book to help you determine the slope on which you will be operating your unit. Never allow someone to stand or ride on or in an attachment or trailer. ELECTRICAL SAFETY SYSTEM The electrical system has two primary components, an Operator Presence System and a Select Reverse� system. Operator Presence System (Seat) The seat has an Operator Presence System to shut off the engine when the operator leaves the seat. This system is not intended for regular use in stopping the engine or the blade(s). Before leaving the seat, move the blade rotation control to the DISENGAGE position, shift to neutral, set the parking brake and stop the engine. Select Reverse� System The Select Reverse� system will allow the mower blade(s) to continue to rotate when traveling in reverse. See “How To Operate The Ignition Key Switch” and “How To Start The Engine” for further details. HOW TO OPERATE THE IGNITION KEY SWITCH Use the ignition key switch to start and stop the engine. When you start the engine and release the ignition key, the ignition key switch will automatically default to the recommended RUN-MOW position for normal mowing. START - Use this position to start the engine. RUN-MOW - When you start the engine and release the ignition key, the ignition key switch will automatically default to the recommended RUN-MOW position for normal mowing. In the RUN-MOW position, the system will stop the engine and the blade(s) when the speed control pedal/shift lever is put in the reverse position. SELECT REVERSE� - The optional Select Reverse� position will allow the mower blade(s) to continue to rotate when traveling in reverse. Always go back to the recommended RUN-MOW position for normal mowing when operation in Select Reverse� is not absolutely necessary. NEVER use the Select Reverse� option if children are on or near the property. WARNING: Operators are strongly discouraged from using this option unless the operator de- cides such operation is absolutely necessary and that safe precautions are taken. Never use the Select Re- verse� option if children are on or near the property. Always look down and behind before and while backing. After using the Select Reverse� position, move the ignition key back to the RUN-MOW position. STOP - Use this position to stop the engine. Figure 6 Ignition Key Switch HOW TO USE THE THROTTLE CONTROL Use the throttle control to increase or decrease the speed of the engine. CAUTION: Always operate the engine with the throttle control in the FAST position. If the engine runs for several minutes at slower than the FAST position, the engine and transmission will overheat and can be damaged. 1. Move the throttle/choke control completely forward to the CHOKE position to start a cold engine. 2. The FAST position is marked with a detent. For normal opera- tion and when using a grass bagger, move the throttle control to the FAST position. For maximum charging of the battery and for a cooler running engine and transmission, operate the en- gine in the FAST position. 3. For transport and to tow pull behind attachments, move the throttle control to the SLOW position. 4. The engine governor is set at the factory for maximum perform- ance. Do not adjust the governor to increase the speed of the engine.

THE BLADE ROTATION CONTROL The blade rotation control is next to the steering wheel (Figure 7). Use the blade rotation control to engage the blade(s) or to operate a snow thrower attachment. 1. Before you start the engine, make sure the blade rotation con- trol is in the DISENGAGE position. 2. Move the blade rotation control to the ENGAGE position to rotate the blade(s). Note: If the engine stops when you engage the blade(s), the transmission is in reverse. 3. Move the blade rotation control to the DISENGAGE position to stop the blade(s). Before you leave the operator’s position, make sure the blade(s) has stopped rotating. 4. Before you ride the unit across a sidewalk or a road, move the blade rotation control to the DISENGAGE position. 5. Before operating in reverse, move the blade rotation control to the DISENGAGED position. If the blade rotation control is not in the DISENGAGED position, the engine will stop when the speed control pedal/shift lever is moved to REVERSE position. WARNING: Always keep your hands and feet away from the blade, deflector opening, and the mower housing when the engine runs. Blade Rotation Control Engage Position Disengage Position Figure 7 HOW TO USE THE SHIFT LEVER To change the forward speed or the direction of the unit, follow the steps below. CAUTION: Before you move the shift lever, completely push the clutch/brake pedal forward to stop the unit. If the unit is not stopped, the gearbox can be damaged. 1. Completely push the clutch/brake pedal forward to stop the unit. Keep your foot on the pedal. 2. Move the throttle control lever to the SLOW position. 3. To go forward, move the shift lever to a forward speed setting. 4. To go backward, move the shift lever to reverse. Always disen- gage blades and look down and behind before and while back- ing. 5. Slowly release the clutch/brake pedal. Do not keep your foot on the pedal. 6. Move the throttle control to the FAST position. FUNCTION SHIFT LEVER 5−6 Speeds THROTTLE Trimming Snow Thrower 1 Bagging Grass 1 or 2 FAST Mulching Grass 1 or 2 FAST CHOKE Normal Mowing 2 or 3 FAST Easy Mowing Snow Blade 3 or 4 SLOW Transport 5-6 THROTTLE Attachments * * See the Instruction Book for the Attachment.

1. Completely push the clutch/brake pedal forward. 2. Lift the parking brake lever (Figure 8). 3. Remove your foot from the clutch/brake pedal and then release the parking brake lever. Make sure the parking brake will hold the unit. 4. To release the parking brake, completely push the clutch/brake pedal forward. The parking brake will automatically release. WARNING: Before you leave the operator’s position, move the shift lever to the neutral (N) position. Set the parking brake. Move the blade rotation control to the DISENGAGE position. Stop the engine and remove the ignition key. Figure 8 Parking Brake HOW TO CHANGE THE CUTTING HEIGHT To change the cutting height, raise or lower the lift lever as follows. 1. Move the lift lever forward to lower the mower housing and back to raise the mower housing (Figure 9). 2. When you ride on a sidewalk or road, move the lift lever to the highest position and move the blade rotation control to the DISENGAGE position. Lift Lever Figure 9 HOW TO STOP THE UNIT 1. Completely push the clutch/brake pedal forward to stop the unit. Keep your foot on the pedal. 2. Move the blade rotation control to the DISENGAGE position. 3. Move the shift lever to the NEUTRAL position. 4. Set the parking brake. WARNING: Make sure the parking brake will hold the unit. 5. Move the throttle control to the SLOW position. 6. To stop the engine, turn the ignition key to the STOP posi- tion. Remove the key. HOW TO TRANSPORT THE UNIT To transport the unit, follow the steps below. 1. Move the blade rotation control to the DISENGAGE position 2. Raise the lift lever to the highest position. 3. Move the throttle control to a position between SLOW and FAST. 4. To go faster, move the shift lever to a faster speed.

WARNING: The deflector is a safety device. Do not re- move the deflector. The deflector forces the dis- charged material toward the ground. Always keep the deflector in the down position. If the deflector is dam- aged, replace the deflector with an original equipment part from an authorized service center. IMPORTANT: When you operate with the mower housing, always operate with the throttle control in the FAST position. 1. Start the engine. 2. Move the lift lever to a height of cut position. In high or thick grass, cut the grass in the highest position first and then lower the mower housing to a lower position. CAUTION: Do not operate with the mower housing in the LEVEL ADJUSTMENT position. If you operate in the LEVEL ADJUSTMENT position, the mower housing and blades can be damaged. 3. Move the throttle control to the SLOW position. 4. Slowly move the blade rotation control to the ENGAGE position. 5. Push the clutch/brake pedal completely forward. 6. Move the shift lever to one of the speed settings. NOTE: When you mow in heavy grass or mow with a bagger, put the shift lever in the slowest speed. 7. Slowly release the clutch/brake pedal. 8. Move the throttle control to the FAST position. If you need to go faster or slower, stop the unit and move the shift lever to another speed setting. 9. Make sure the level of cut is still correct. After you mow a short distance, look at the area that was cut. If the mower housing does not cut level, see the instructions on “How To Level The Mower Housing” in the Maintenance section. WARNING: For better control of the unit, always select a safe speed. HOW TO OPERATE THE UNIT ON HILLS WARNING: Do not ride up or down slopes that are too steep to back straight up. Never ride the unit across a slope. See the “Slope Guide” in the back of this book for information on how to check slopes. 1. Before you ride up or down a hill, move the shift lever to the slowest speed. 2. Do not stop or change speed settings on a hill. If you must stop, quickly push the clutch/brake pedal forward and set the parking brake. 3. To start again, make sure the shift lever is in the slowest speed. Move the throttle control to the SLOW position. Slowly release the pedal. 4. If you must stop or start on a hill, always have enough space for the unit to roll when you release the brake and engage the clutch. 5. Be very careful when you change directions on a hill. When on a slope or in a turn on a hill, move the throttle control to the SLOW position to help prevent an accident.

CHECK THE OIL NOTE: The engine was shipped from the factory filled with oil. Check the level of the oil. Add oil as needed. See the engine manufacturer’s instructions for the type of gasoline and oil to use. 1. Make sure the unit is level. NOTE: Do not check the level of the oil while the engine runs. 2. Check the oil. Follow the procedure in the engine manufactur- er’s instructions. 3. If necessary, add oil until the oil reaches the FULL mark on the dipstick. The quantity of oil needed from ADD to FULL is shown on the dipstick. Do not add too much oil. ADD GASOLINE WARNING: Always use a safety gasoline container. Do not smoke when adding gasoline to the fuel tank. Do not add gasoline when you are inside an enclo- sure. Before you add gasoline, stop the engine and let the engine cool for several minutes. Fill the fuel tank with regular unleaded gasoline. Do not use premium unleaded gasoline. Make sure the gasoline is fresh and clean. Leaded gasoline will increase deposits and shorten the life of the valves. CAUTION: A mixture of alcohol (ethanol or methanol) and gasoline (called gasohol), will attract moisture and cause acid deposits during storage. While the unit is in storage, the acids in the fuel can damage the fuel system. To prevent engine problems with the fuel system, empty the fuel system before storage of 30 days or longer as follows. 1. Drain the fuel tank. 2. Start the engine. Let the engine run until the fuel lines and the carburetor are empty. 3. After storage, make sure you use fresh fuel. See the storage instructions for additional information. 4. Never use engine cleaner or carburetor cleaner in the fuel tank or permanent damage can occur. CARBURETOR The factory settings for the carburetor are for most conditions. If the engine is operated under the following conditions, you can adjust the carburetor mixture. To adjust the carburetor, see the engine manufacturer’s instructions. 1. The engine has a loss of power or does not run smooth. 2. A change from summer to winter operation. 3. A 40 degree change in the operation temperature. The carbure- tor was adjusted at 80 degrees at the factory. 4. The engine is operated above 4,000 feet. HOW TO START THE ENGINE WARNING: The electrical system has two primary components, an operator presence system and a Se- lect Reverse� system. The operator presence sys- tem determines if the operator is sitting on the seat. This system will stop the engine when the operator leaves the seat. The Select Reverse� system gives the operator the ability to temporarily mow in reverse if he decides such operation is absolutely necessary and safe operating precautions are taken. For your protection, always make sure these systems operate correctly. NOTE: The engine will not start unless you depress the clutch/brake pedal or engage the parking brake and move the blade rotation control to the DISENGAGE position. 1. Make sure the spark plug wire is connected to the spark plug. 2. Push the clutch/brake pedal completely forward. Keep your foot on the pedal. 3. Move the shift lever to the neutral (N) position. 4. Make sure the blade rotation control is in the DISENGAGE position. If the blade rotation control is not in the DISENGAGE position, the engine will not start. 5. Move the throttle control completely forward to the CHOKE or FAST position. Some models have a separate choke knob. Pull the choke knob to the full CHOKE position. 6. Turn the ignition key to the START position. Release the key when the engine starts. The ignition key switch will auto- matically default to the recommended RUN-MOW position for normal mowing. See “How To Operate The Ignition Key Switch” in the Operation Section. NOTE: If the engine does not start after four or five tries, see the TROUBLE SHOOTING CHART. 7. Slowly move the throttle control to the SLOW position. 8. Let a cold engine run for several minutes. Begin work when the engine is warm. To start a hot engine, move the throttle control to a position between FAST and SLOW. Fuel Tank Full

blade(s) to disengage correctly, the adjustment must be cor- rect. 2. Before you use the unit, check the oil in the engine and add oil if necessary. 3. If the engine will not start, first make sure the wire is attached to the spark plug. 4. Make sure all the belts are inside all the belt guides. See the in- structions on how to remove and install the motion drive and mower drive belts. 5. Before you make an inspection, adjustment (except for the car- buretor) or repair, make sure the wire from the spark plug is dis- connected. 6. For longer life of the battery on electric start models, charge the battery every three months. 7. Use the shift lever to change the ground speed, not the throttle control. 8. Belt noise can occur when the blade or clutch is engaged. This noise is normal and does not affect the operation of the unit. MOWING AND BAGGING TIPS 1. For a lawn to look better, check the cutting level of the mower housing. See “How To Level The Mower Housing” in the Main- tenance section. 2. For the mower housing to cut level, make sure the tires have the correct amount of air pressure and use slow ground speeds when turning. 3. Every time you use the unit, check the blade. If the blade is bent or damaged, immediately replace the blade. Also, make sure the nut for the blade is tight. 4. Keep the blade(s) sharpened. Worn blades will cause the ends of the grass to turn brown. 5. Do not cut or bag grass that is wet. Wet grass will not discharge correctly. Let the grass dry before cutting. 6. Use the left side of the mower housing to trim near an object. 7. Discharge the cut grass onto the mowed area. The result is a more even discharge of cut grass. 8. When you mow large areas, start by turning to the right so that the cut grass will discharge away from shrubs, fences, drive- ways, etc. After one or two rounds, mow in the opposite direc- tion making left turns until finished (Figure 10). 9. Use a mowing pattern that eliminates reverse travel as much as possible. 10. If the grass is very high, cut two times to decrease the load on the engine. First cut with the mower housing in the highest posi- tion and then lower the mower housing for the second cut. 11. For better engine performance and an even discharge of the cut grass, always operate the engine with the throttle in FAST position. 12. When you use a bagger, operate the engine with the throttle in FAST position and the shift lever in first or second gear. 13. For better cutting performance and a quality cut, mow with the shift lever in one of the slower speeds. 14. After each use, clean the bottom and top of the mower housing for better performance. Also, a clean mower housing will help prevent a fire. Figure 10

use Maintenance engine. Refer to the Engine Owner’s Manual. Examine blade(s). Check for cracks, wear, and excessive damage. Remove debris from unit and mowing area. Examine all rotating and sliding parts. Check tire inflation. Refer to the Maintenance section. Verify that the mower housing is level. Refer to the Maintenance section. Examine V-belts. Check for cracks, wear, and excessive damage. Check brake operation. Refer to the Operation and Maintenance sections. After completion of first 5 hours Change oil. Refer to the Engine Owner’s Manual. After 25 hours Maintenance engine. Refer to the Engine Owner’s Manual. Remove, examine, sharpen, and balance blade(s). Refer to Maintenance section. Check adjustments: a. Blade Rotation Control b. Brake c. Clutch d. Steering Refer to Maintenance section. Lubricate chassis and mower housing. Refer to Where to Lubricate instructions. Check the muffler: a. Torque b. For wear or burn out c. Condition of spark arrestor, (if applicable). Refer to Maintenance section. Before storage of 30 days or more Prepare engine for storage. Refer to the Engine Owner’s Manual. Drain fuel system. Refer to warnings in the Owner’s Manual. Add fuel stabilizer. Refer to the Engine Owner’s Manual. Prepare battery for storage: a. Remove from unit. b. Fully charge. c. Move to cool dry place. GENERAL RECOMMENDATIONS 1. The owner’s responsibility is to maintain this product. This will extend the life of the product and is also necessary to maintain warranty coverage. 2. Check the spark plug, drive brake, lubricate the unit, and clean the air filter once a year. 3. Check the fasteners. Make sure all fasteners are tight. 4. Follow the Maintenance section to keep the unit in good operat- ing condition. WARNING: Before you make an inspection, adjust- ment, or repair to the unit, disconnect the wire to the spark plug. Remove the wire from the spark plug to prevent the engine from starting by accident. NOTE: Torque is measured in foot pounds (metric Nm). This measurement describes how tight a nut or bolt must be. The torque is measured with a torque wrench. HOW TO CHECK THE MUFFLER Check the muffler every 50 hours. Make sure the muffler is correctly mounted and is not loose. If the muffler is worn or burnt, replace with a new muffler. A worn muffler is a fire hazard and can also damage the engine. If you mount a spark arrester to the muffler, also check the spark arrester when you check the muffler. If the spark arrester is worn or damaged, replace it with a new spark arrester. See your nearest authorized service center for a spark arrester.

disconnect the wire to the spark plug. If the blade hits an object, stop the engine. Check the unit for dam- age. The blade has sharp edges. When you hold the blade, use gloves or cloth material to protect your hands. If you keep the blade sharp and inspect the blade for damage, the blade will cut better and be more safe to operate. Frequently check the blade for excessive wear, cracks, or other damage. Frequently check the nut that holds the blade. Keep the nut tight. If the blade hits an object, stop the engine. Disconnect the wire to the spark plug. See if the blade is bent or damaged. Check the blade adapter for damage. Before you operate the unit, replace damaged parts with original equipment parts. See the authorized service center in your area. Every three years, have an authorized service person inspect the blade or replace the old blade with an original equipment part. HOW TO REMOVE AND INSTALL THE BLADE 1. Remove the mower housing. See the instructions on “How To Remove The Mower Housing”. 2. Use a piece of wood to keep the blade from rotating. 3. Remove the nut that holds the blade (Figure 11). Hi-Lift Edge Up Mandrel Blade Adapter Blade Belleville Washer Washer Nut Figure 11 4. Check the blade and the blade adapter according to the in- structions for “Inspect Blade”. Replace a badly worn or dam- aged blade with an original equipment blade. See an authorized service center in your area. 5. Clean the top and bottom of the mower housing. Remove all the grass and debris. 6. Mount the blade and blade adapter on the mandrel (Figure 11). 7. Mount the blade so that the hi-lift edges are up. If the blade is upside down, the blade will not cut correctly and can cause an accident. 8. Fasten the blade with the original washers and nut. Make sure the outside rim of the Belleville washer is against the blade (Figure 12). WARNING: Always keep the nut tight that holds the blade. A loose nut or blade can cause an accident. 9. Tighten the nut that holds the blade to a torque of 35 foot pounds (47,5 N-m). 10. Install the mower housing. See “How To Install The Mower Housing”. Blade Adapter Blade Belleville Washer (Outside rim must be against the blade.) Washer Nut Figure 12 HOW TO SHARPEN THE BLADE WARNING: Vibration can be caused if the blade is not correctly balanced or if the blade is damaged. A blade that is damaged with cracks can break and cause an accident. Keep a sharp edge on the blade. A blade that is not sharp will cause the tips of the grass to become brown. 1. Sharpen the blade two times a year or every 25 hours. 2. Remove the blade according to the instructions in “How To Re- move And Install The Blade”. 3. Clean the blade with a brush, soap and water. Check the blade. Look for cracks, nicks, or other damage. Replace a badly worn or damaged blade with an original equipment blade. See an authorized service center in your area. 4. Sharpen the blade with a file (Figure 13). Make sure you keep the original bevel angle. 5. Make sure the blade is balanced. Use a screwdriver and hold the blade parallel to the ground (Figure 13). A blade that is balanced will stay parallel to the ground. If the blade is not bal- anced, the heavy end will rotate toward the ground. Sharpen the heavy end until the blade is balanced. 6. A new blade will cut better than a badly worn blade. Every three years, have an authorized service person inspect the blade or replace the old blade with an original equipment blade. 7. Assemble the blade according to the instructions “How To Re- move And Install The Blade”. Ground Blade is balanced when parallel to the ground. Screwdriver Blade File Figure 13

WARNING: To prevent an injury, the blade rotation control must operate correctly. In normal usage, the blade rotation control will not require an adjustment. However, if the cutting performance decreases or the quality of cut is poor, make the following changes. 1. When you mow, make sure the throttle control in in the FAST position. 2. Move the blade rotation control to the DISENGAGE position (Figure 14). 3. Stop the engine. Disconnect the wire from the spark plug. Blade Rotation Control Engage Position Disengage Position Figure 14 4. Check the blade(s). Keep a sharp edge on the blade(s). A blade that is not sharp will cause the tips of the grass to become brown. 5. Disconnect the blade drive spring from the blade control rod. Move the blade drive spring to the middle hole (Figure 15). This will increase the tension on the mower drive belt. Figure 15 Blade Control Rod Blade Drive Spring Top Hole (New Belt) Middle Hole Bottom Hole DISENGAGE POSITION 6. Attach the wire to the spark plug. Mow for a short distance and again check the quality of cut. If necessary, move the blade drive spring to the bottom hole. 7. Again check the quality of cut. If the quality of cut has not im- proved, replace the mower drive belt. See “How To Replace The Mower Drive Belt”. If replacing the belt does not correct the problem, take the unit to an authorized service center. 8. Move the blade rotation control to the DISENGAGE posi- tion. Stop the engine. Disconnect the wire from the spark plug. Check the operation of the blade brake. Rotate the pulleys with your hand. Make sure the brake pads are pressed tightly against the pulleys (Figure 16). WARNING: If the brake pads do not press tightly against the pulleys, take the unit to an authorized service center. Blade Brake Brake Pad Against Pulley Figure 16 9. Move the blade rotation control to the ENGAGE position. Check the pads for the blade brake. If the pads are excessively worn or damaged, replace the brake pad assemblies. Correct replacement parts and assistance are available from an autho- rized service center. 10. Attach the wire to the spark plug. Mow for a short distance and again check the operation of the blade rotation control. 11. When you move the blade rotation control to the DISENGAGE position, all movement will stop within five se- conds. If there is movement of the belt or the blades continue to rotate, engage and disengage the blade rotation control five times to remove any excess rubber from a new mower drive belt. If you need assistance, take the unit to an autho- rized service center. 12. If you replace the mower drive belt, move the blade drive spring to the top hole (Figure 15).

Completely push the clutch/brake pedal forward. Set the parking brake. Move the shift lever to the neutral (N) position. Push the unit. If the rear wheels rotate, adjust or replace the brake pads. Adjust the drive brake as follows. 1. The location of the drive brake is on the right side of the gearbox (Figure 17). 2. Make sure the parking brake is set and the shift lever is in neutral (N). Turn the hex nut in a clockwise direction until the rear wheels do not turn when the unit is pushed forward. 3. Release the parking brake and push the unit. If the unit does not roll, turn the hex nut in a counterclockwise direction until the unit rolls. 4. Set the parking brake. Push the unit. If the rear wheels do not turn, the drive brake is correctly adjusted. Release the parking brake. WARNING: If you cannot correctly adjust the drive brake, replace the brake pads. Correct replacement parts and assistance are available from an autho- rized service center. Figure 17 Drive Brake Gearbox Hex Nut HOW TO CHECK AND ADJUST THE CLUTCH If the motion drive belt is loose, the clutch will slip when; (1) going up a hill, (2) pulling a heavy load, or (3) the unit will not move forward. Adjust the clutch as follows. WARNING: Before you make an inspection, adjust- ment, or repair to the unit, disconnect the wire to the spark plug. Remove the wire from the spark plug to prevent the engine from starting by accident. 1. Check the routing of the motion drive belt. Make sure the belt is installed correctly and is inside all the belt guides. 2. Remove the cotter pin, washer, and brake spring from the adjustable nut (Figure 18). 3. Disconnect the adjustable nut from the brake lever assembly and the parking brake latch. 4. Align the hole in the brake lever with the hole in the frame. Hold the brake lever in place with a 1/4 inch (6 mm) pin or bolt (Figure 18). 5. Pull the clutch rod forward until tight. Turn the adjustable nut until the nut will fit through the hole in the brake lever. 6. Assemble the adjustable nut to the parking brake latch, brake lever and brake spring. Fasten with the washer and cotter pin. 7. Remove the 1/4 inch (6 mm) pin or bolt. 8. If the belt still slips after the clutch has been adjusted, then the motion drive belt is worn or damaged and must be replaced. See “How To Replace The Motion Drive Belt”. Clutch Rod Brake Lever Assembly Adjustable Nut Figure 18 Cotter Pin Brake Spring Washer Parking Brake Latch Pin or Bolt

If the NEUTRAL position on the shift lever does not match neutral on the gearbox, adjust the shift lever as follows. 1. Stop the engine. 2. Disconnect the adjuster nut from the shifter bracket (Figure 19). 3. Make sure the shift lever is in the NEUTRAL position. 4. Push the unit forward. Make sure the gearbox is in neutral. 5. To align the adjuster nut with the hole in the shifter bracket, turn the adjuster nut. 6. Connect the adjuster nut to the shifter bracket. 7. Make sure the NEUTRAL position on the shift lever matches neutral on the gearbox. Adjuster Nut Hair Pin Shift Link Shifter Bracket Motion Drive Belt Figure 19 Shift Lever MAINTENANCE FREE BATTERY HOW TO REMOVE THE BATTERY To charge or clean the battery, remove the battery from the unit as follows. WARNING: To prevent sparks, disconnect the black battery cable from the negative (-) terminal before you disconnect the red cable. WARNING: The battery contains sulfuric acid which is harmful to the skin, eyes and clothing. If the acid gets on the body or clothing, wash with water. 1. Disconnect the black cable from the negative (-) terminal (Figure 20). 2. Disconnect the red cable from the positive (+) terminal. 3. Lift the battery tray and the battery out of the unit. HOW TO CLEAN THE BATTERY 1. Remove the battery. 2. Wash the battery with a solution of one gallon of water and four tablespoons of baking soda (sodium bicarbonate). Make sure the solution does not get into the battery cells. 3. Clean the terminals and the ends of the cables with a wire brush. 4. Install the battery. 5. To prevent corrosion, apply grease to the battery terminals. HOW TO CHARGE THE BATTERY WARNING: When you charge the battery, do not smoke. Keep the battery away from any sparks. The fumes from the battery acid can cause an explosion. 1. Before you charge the battery, remove the battery. 2. To charge the battery, use a 12 volt battery charger. Charge at a rate of 6 amperes for 1 hour. 3. Install the battery. WARNING: To prevent sparks, fasten the red cable to the positive (+) terminal before you connect the black cable. 4. Fasten the red cable to the positive (+) terminal with the fas- teners as shown. 5. Fasten the black cable to the negative (-) terminal with the fas- teners as shown. Positive (+) Terminal Black Cable Red Cable Battery Tray Battery Figure 20 Carriage Bolt Wing Nut Carriage Bolt

Lubricate the areas shown with engine oil. Apply grease with a brush to the areas shown. Models with grease fittings: Lubricate with grease gun. NOTE: Apply grease to the steering gear assembly. CAUTION: If the unit is operated in dry areas that have sand, use a dry graphite spray to lubricate the unit. HOW TO CHECK THE FUEL FILTER NOTE: Before you replace the fuel filter or the fuel line, the fuel tank must be empty. If the fuel filter is dirty, the engine will run rough and have less performance. Remove the old filter (Figure 22). Replace the old filter with a new filter. Use an original equipment part. See an authorized service dealer in your area. Fuel Line Clips Fuel Filter Figure 22 CHECK THE TIRES Check the air pressure in the tires. Tires with too much air pressure will cause the unit to ride rough. Also, the wrong air pressure will keep the mower housing from cutting level. The correct air pressure is shown on the side of the tire. Figure 21

is spring loaded. Make sure the lift lever is locked in the LEVEL ADJUST- MENT position. Level Adjustment Position Figure 23 MAINTENANCE 27 F-050706L HOW TO REMOVE THE MOWER HOUSING 1. Move the blade rotation control to the DISENGAGE position. 2. If equipped, remove the gauge wheels. 3. Move the lift lever to the level adjustment position(Figure 23). 4. Remove the hair pins and the washers from the adjuster arms (Figure 24). See illustra- tions “C” and “D”. 5. Remove the hair pins and washers from the suspension links. See illustrations “A” and “B”. 6. Disconnect the extension spring from the blade control rod. See illustration “E”. 7. Disconnect the front hanger from the axle support. See illustration “F”. 8. Remove the mower drive belt from the stack pulley. 9. Pull the mower housing away from the right side of the unit. 10. To operate without the mower housing, move the lift lever to the TOP position. HOW TO INSTALL THE MOWER HOUSING 1. Push the mower housing under the right side of the unit. 2. Put the mower drive belt around the stack pulley. Make sure the “V” side of the mower drive belt is against the stack pulley. Also, make sure the mower drive belt is not twisted. 3. Attach the front hanger to the axle support with the hanger rod. Fasten with the fasteners as shown. See illustration “F”. 4. Make sure the mower drive belt is between the stack pulley and the two belt guides. See illustration “G”. 5. Attach the suspension links to the lifter assembly. Fasten with the washers and hair pins. See illustrations “A” and “B”. 6. Attach the right and the left adjuster arms to the suspension brackets. Fasten with the washers and hair pins. See illustra- tions “C” and “D”. 7. Attach the extension spring to the blade control rod. See illustration “E”. 8. Move the blade rotation control to the ENGAGE position. Make sure the mower drive belt is inside all the belt guides. 9. Make sure the mower housing is level. See the instructions on “How To Level The Mower Housing”. 10. If equipped, install the gauge wheels. 11. Check the operation of the blade rotation control. See the in- structions on “How To Adjust The Blade Rotation Control”. Lifter Assembly Blade Rotation Control Hanger Rod Mower Drive Belt Lift Lever Front Hanger Extension Spring Blade Control Rod Suspension Link Adjuster Arm Belt Guide Belt Guide Stack Pulley Mower Drive Belt Suspension Link A B A B A B A B Adjuster Arm Figure 24 Gauge Wheel

The axle bolts for the gauge wheels were mounted in the LOW cut position. To change the position of the gauge wheels, move the axle bolts as follows. IMPORTANT: Before you adjust the gauge wheels, you must do the following. Make sure the mower housing is level. Make sure the height of cut is set at the height you want for your lawn. Mow a short distance on a flat level area and look at the area that was cut. If the mower housing does not cut level, see the instructions “How To Level The Mower Housing.” WARNING: Before you make an inspection, adjust- ment, or repair to the unit, disconnect the wire to the spark plug. Remove the spark plug wire to prevent the engine from starting by accident. 1. Remove the gauge wheels (Figure 25). 2. Mow a short distance on a flat level area to check the level of cut and the height of cut. Look at the height of cut position number on the lift lever (Figure 26). 3. Look at each gauge wheel bracket. There are 3 holes in each bracket and a number next to each hole. The number for the height of cut position on the lift lever indicates the correct hole to use on each gauge wheel bracket (Figure 27). 4. Assemble the axle bolts to the gauge wheel brackets using the correct hole in the bracket as indicated (Figure 27). NOTE: If the height of cut position is changed by the lift lever, you must move the gauge wheels to the correct hole (Figure 27) to keep a level height of cut. Gauge Wheel Figure 25 Locking Ring Washer Axle Bolt Figure 26 Cutting Height Positions Lift Lever Wheel Bracket Hole No. Lift Lever Position No. 1 1 2 2 3 3,4,5,6 Figure 27 Gauge Wheel Bracket

If the mower housing is level, the blade will cut easier and the lawn will look better. WARNING: Before you make an inspection, adjust- ment, or repair to the unit, disconnect the wire to the spark plug. Remove the spark plug wire to prevent the engine from starting by accident. 1. Make sure the unit is on a hard flat surface. 2. Check the air pressure in the tires. If the air pressure is incor- rect, the mower housing will not cut level. The correct air pres- sure is shown on the side of the tire. IMPORTANT: On models equipped with gauge wheels, the gauge wheels must be removed to correctly adjust the level of the mower housing. 3. Some models have gauge wheels on the mower housing. If equipped, remove the gauge wheels. 4. Open the cover. 5. Move the lift lever to the LEVEL ADJUSTMENT position (Figure 28). WARNING: The lift lever is spring loaded. Make sure the lift lever is locked in the LEVEL ADJUSTMENT position. 6. Loosen the left and right adjuster knobs (Figure 29). Push down on each side of the mower housing. Make sure both sides of the mower housing are setting on a flat surface. Also, make sure the lift links are loose and can easily move up or down. 7. Push down on the lift links and tighten the left and right adjust- er knobs (Figure 29). Make sure the adjuster knobs are tight. If necessary, use a wrench to tighten the adjuster knobs. Tighten to a torque of 10 foot pounds (13,5 N-m). 8. Raise the lift lever from the LEVEL ADJUSTMENT position to a CUTTING HEIGHT position (Figure 30). 9. Close the cover. 10. If equipped, install the gauge wheels. 11. Attach the spark plug wire to the spark plug. 12. Mow for a short distance. If the height of cut is not level, repeat the above steps. CAUTION: Do not operate with the mower housing in the LEVEL ADJUSTMENT position. If you operate in the LEVEL ADJUSTMENT position, the mower housing and blades can be damaged. Figure 28 Level Adjustment Position Cutting Height Positions Cover Lift Lever Figure 29 Adjuster Knobs Lift Link Figure 30 Cutting Height Positions Cover Lift Lever

THE MOTION DRIVE BELT REMOVAL 1. Remove the mower housing. See the instructions on “How To Remove The Mower Housing”. 2. Completely push the pedal forward and engage the parking brake. 3. Remove the idler pulley (Figure 31). Idler Pulley Motion Drive Belt Loosen The Belt Guides Drive Pulley Figure 31 4. To access the belt guides, remove the battery and battery tray. See “How To Remove The Battery”. 5. Loosen the belt guides at the drive pulley (Figure 32). Figure 32 Belt Guides Seat Spring 6. Remove the motion drive belt from the drive pulley (Figure 31). 7. Remove the adjuster nut from the shifter bracket (Figure 33). Pull the motion drive belt over the shifter bracket. Adjuster Nut Hair Pin Shift Link Shifter Bracket Motion Drive Belt Figure 33 8. To remove the motion drive belt from the stack pulley, pull the front end of the belt under the stack pulley and then back between the stack pulley and the steering plate (Figure 34). Motion Drive Belt Figure 34 FRONT Stack Pulley Steering Plate Belt Guides 9. Remove the access panel (Figure 35). 10. Remove the two screws that attach the steering shaft assembly (Figure 35). Raise the steering wheel and steering shaft assembly. Pull the motion drive belt under the steering shaft assembly. Figure 35 Screw Steering Shaft Assembly Motion Drive Belt Access Panel 11. Remove the motion drive belt. A correct replacement part or assistance is available from an Authorized Service Center in your area.

belt guides (Figure 34). Install the motion drive belt on the top pulley of the stack pulley. Make sure the “V” side of the belt is against the pulley. 2. Push the motion drive belt through the opening between the steering plate and the engine plate. 3. Install the end of the motion drive belt around the drive pulley (Figure 31). 4. Tighten the belt guides at the drive pulley (Figure 32). 5. Put the belt around the idler pulley (Figure 31, Figure 36). Assemble the idler pulley. Fasten the idler pulley with the hex nut. Make sure the flat side of the belt is against the idler pulley. Also, make sure the belt is not twisted. 6. Make sure the motion drive belt is inside all the belt guides (Figure 31, Figure 32). 7. Attach the adjuster nut and shift link to the adjuster bracket with a hair pin (Figure 33). See “How To Adjust The Shift Lever”. 8. Attach the steering shaft assembly to the steering plate with two screws (Figure 35). 9. Attach the access panel (Figure 35). 10. Check the routing of the motion drive belt. Make sure the motion drive belt is installed correctly on the idler pulley. Make sure the steering shaft assembly in inside the motion drive belt (Figure 36). 11. Install the battery. 12. Before you use the unit, check the adjustment of the clutch. See the instructions “How To Check And Adjust The Clutch”. 13. Install the mower housing. See the instructions “How To Install The Mower Housing”. Figure 36 Motion Drive Belt Idler Pulley Stack Pulley Steering Shaft Assembly

1. Remove the mower housing. See the instructions on “How To Remove The Mower Housing”. 2. Pull the belt retainer away from the idler pulley and remove the mower drive belt (Figure 37). 3. Pull the belt retainer away from the right mandrel pulley and remove the mower drive belt. 4. Pull the belt retainer away from the left mandrel pulley and remove the mower drive belt. NOTE: Replace the mower drive belt with an original equipment belt from an authorized service center. 5. Install the new mower drive belt. Pull the belt retainer away from the right mandrel pulley. Put the belt around the right mandrel pulley. 6. Pull the belt retainer away from the left mandrel pulley. Put the belt around the left mandrel pulley. 7. Pull the belt retainer away from the idler pulley. Put the flat side of the mower drive belt around the idler pulley. 8. Make sure the “V” side of the mower drive belt is against the mandrel pulleys as shown. 9. Install the mower housing. See the instructions on “How To Install The Mower Housing”. 10. Before you mow, check the blade rotation control. See the in- structions on “How To Adjust The Blade Rotation Control”. Figure 37 Mower Drive Belt Belt Retainer Right Mandrel Pulley Belt Retainer Left Mandrel Pulley Idler Pulley Belt Retainer

If the wheels must be removed for service, make sure they are installed as follows. Front Wheel 1. Make sure the valve stem is to the outside of the tractor. Slide the front wheel on the spindle (See Figure 38). 2. Fasten the front wheel with washer and cotter pin. Bend the ends of the cotter pin apart to keep the front wheel on the spindle. 3. If your model has hub caps, install the hub caps. Make sure the washer hold the hub caps in place. Rear Wheel 1. Install the washers and spacer onto the axle as shown in Figure 39. 2. Mount the square key in the key slot (See Figure 39). 3. Make sure the valve stem is to the outside of the tractor. Align the slot in the rear wheel with the square key. Slide the rear wheel on the axle. 4. Fasten the rear wheel with washer and e-ring . 5. If your model has hub caps, install the hub caps. Make sure the washer hold the hub caps in place. Figure 38 Front Wheel Spindle Valve Stem Washer Washer Hub Cap Cotter Pin Figure 39 E-Ring Washer Hub Cap Washer Spacer Square Key Valve Stem Key Slot Axle Rear Wheel

If the fuse is blown, the engine will not start. The location of the fuse is next to the battery. Remove the fuse and replace with a automotive fuse (Figure 40). Figure 40 Automotive Fuse HOW TO REPLACE THE LIGHT BULB 1. Raise the tractor hood. 2. Turn the light socket until the tabs on the socket align with the notches in the bezel (Figure 41). Remove the light socket. Turn the light bulb and remove the bulb. 3. Install a new light bulb. Align the light socket with the notches in the bezel and turn the light socket to lock in position. Bezel Light Bulb Light Socket Figure 41 HOW TO CLEAN THE MOWER HOUSING WARNING: Before you clean the mower housing, stop the engine and disconnect the wire to the spark plug. Grass and other debris on top of the mower housing can keep the belt from working correctly. For safety and correct operation, frequently clean the top of the mower housing. Remove grass and debris from around the pulleys and other moving parts. 1. Move the lever for the blade rotation control to the ENGAGE position. 2. Clean the top of the mower housing. 3. Move the lever for the blade rotation control to the DISENGAGE position. 4. Again clean the top of the mower housing. 5. After you cut the grass, clean the bottom of the mower housing. STORAGE (over 30 days) At the end of each year, prepare the unit for storage as follows. THE ENGINE For storage information, see the the engine manufacturer’s instructions. THE BATTERY 1. Remove the battery. 2. Clean the battery terminals of any deposits. 3. Charge the battery. See the instructions on “How To Prepare And Charge The Battery”. 4. Store the battery in a cool, dry place. NOTE: After a long time in storage, charge the battery. THE FUEL SYSTEM WARNING: Do not drain the gasoline inside a build- ing or near a fire. Do not smoke because the fumes from the fuel can cause an explosion. 1. Start the engine. 2. Run the engine until the fuel tank and the carburetor are out of fuel and the engine stops. 3. Do not leave fuel in the fuel tank or the carburetor. The fuel can damage the function of the fuel system. Some models have a fuel drain (Figure 42). Hold a cloth under the fuel drain. Push the fuel drain until the carburetor is empty. 4. After storage, make sure you use fresh fuel. Figure 42 Fuel Drain CLEAN THE UNIT 1. Clean the dirt and grass from the engine. 2. Clean the mower housing. LUBRICATE THE UNIT See the “Lubrication” instructions in this book.

35 F-050706L PROBLEM: The engine will not start. 1. Follow the steps, “How To Start The Engine” in this book. 2. Electric-Start Models: Clean the battery terminals. Tighten the cables. 3. Drain the fuel tank. Clean the fuel line. Replace the fuel filter. 4. Remove the spark plug(s). Move the throttle to the SLOW posi- tion. Turn the ignition key to the ON position. Try to start the en- gine several times. Install the spark plug. 5. Replace the spark plug. 6. Adjust the carburetor. PROBLEM: The engine will not turn over. 1. Follow the steps, “How To Start The Engine” in this book. 2. Electric-Start Models: Check the level of the acid in the battery. If needed, add water. Charge the battery. 3. Replace the fuse. 4. Check the wiring harness for damage or a loose connection. Repair the damaged wire. 5. Electric-Start Models: replace the solenoid. Recoil-Start Mod- els: replace the module. PROBLEM: The engine is difficult to start. 1. Adjust the carburetor. 2. Replace the spark plug. 3. Replace the fuel filter. PROBLEM: The engine does not run smooth or has a loss of power. 1. Check the oil. 2. Clean the air filter. 3. Clean the air screen. 4. Replace the spark plug. 5. The engine is working too hard. Use a lower gear. 6. Adjust the carburetor. 7. Replace the fuel filter. PROBLEM: The engine does not run smooth at fast speed. 1. Replace the spark plug. 2. Adjust the throttle control. 3. Clean the air filter. 4. Replace the fuel filter. PROBLEM: The engine stops when the blades are engaged. 1. To activate the seat sensor, always sit in the middle of the seat. 2. Check the wiring harness for damage or a loose connection. Repair the damaged wire. 3. Transmission is in reverse. Before operating in reverse, move the blade rotation control to the DISENGAGED position. PROBLEM: On slopes, the engine stops. 1. Mow up and down slopes. Never mow across a slope. 2. To activate the seat sensor, always sit in the middle of the seat. PROBLEM: The engine will not idle. 1. Replace the spark plug. 2. Clean the air filter. 3. Adjust the carburetor. 4. Adjust the throttle control. 5. Drain the fuel tank. Clean the fuel line. Replace the fuel filter. PROBLEM: A hot engine causes a decrease in power. 1. Clean the air screen. 2. Check the oil. 3. Adjust the carburetor. 4. Replace the fuel filter. PROBLEM: Excessive vibration. 1. Replace the blade. 2. Check for loose engine bolts. 3. Decrease the air pressure in the tires. 4. Adjust the carburetor. 5. Check for a damaged belt or damaged pulley. Replace the damaged parts. PROBLEM: The grass does not discharge correctly. 1. Stop the engine. Clean the mower housing. 2. Raise the height of cut. 3. Replace or sharpen the blade(s). 4. Move the shift lever to a slower speed. 5. Move the throttle control to the FAST position. 6. Replace the spring for the blade idler. PROBLEM: The mower housing does not cut level. 1. Check the air pressure in the tires. 2. Adjust the level of the mower housing. 3. Check the front axle. If the front axle does not freely pivot, loos- en the axle bolt(s). PROBLEM: The mower blades will not rotate. 1. Check the mower drive belt. Make sure the belt is installed cor- rectly. 2. Replace the mower drive belt. PROBLEM: The unit will not move when the clutch is engaged. 1. Check the motion drive belt. Make sure the belt is installed correctly. 2. Adjust the clutch. 3. Replace the motion drive belt. PROBLEM: The unit moves slower or stops when the clutch is engaged. 1. Adjust the clutch. 2. Replace the motion drive belt. PROBLEM: When the clutch/brake pedal is released, belt noise can be heard. 1. Temporary belt noise does not change the operation of the unit. If belt noise is continuous, check the routing of the belt. Make sure the belt is inside all belt guides. 2. If the noise is continuous, adjust the clutch. PROBLEM: The rear wheels spin over uneven terrain. 1. Check the front axle. If the front axle does not freely pivot, loos- en the axle bolt(s). PROBLEM: The engine stops when the operator leaves the seat. 1. This is normal. The operator presence system is designed to allow operation only if the operator is in the seat. PROBLEM: The engine stops when selecting reverse travel. 1. Before selecting reverse travel, move the blade rotation control to the DISENGAGE position. See the Operation section for de- tails. PROBLEM: The transaxle is difficult to shift between gears with the engine running and the clutch depressed. 1. Check the clutch adjustment to make sure the belt stops when the clutch pedal is depressed with the transaxle in (N) neutral. 2. Check the belt guides around the transaxle drive pulley. Make sure the belt guides do not touch the pulley.

purchased, a service shop recommended by the store, or an authorized service shop found in the yellow pages of the telephone directory. If you cannot get a repair part or service as described above, call or write to the Central Parts Distributor shown below. When you order, include the following information: (1) Complete Model Number (see nameplate), (2) Date of Manufacture, (3) Complete Part Number, (4) Description, (5) Quantity. Repair parts for the engine or the transmission are available from the manufacturer’s authorized service center found in the yellow pages of the telephone directory. See the individual engine or transmission warranties. If you are unable to obtain parts or service in the manner outlined above, then contact: USA MURRAY, INC., Outdoor Power Equipment, Customer Service Dept., P.O. Box 268, Brentwood, TN 37027 (1-800-251-8007) CANADA MURRAY CANADA, INC., Factory Customer Service, 1195 Coutneypark Drive East, Mississauga, Ont. L5T-1R1 (1-800-661-6662) MURRAY, INC. LAWN MOWER CENTRAL PARTS DISTRIBUTORS BILLIOU’S, INC. 1343 South Main St. Porterville, CA. 93257 (559) 784−4102 1−877−245−5468 FAX 1−800−226−7337 www.billious.com Arizona, California, Hawaii, Nevada BROWN & WISER, INC. 9991 S.W. Avery Street Tualatin, OR. 97062 (503) 692−0330 1−800−882−4782 FAX (503) 691−2041 Alaska, Idaho (counties Ada, Adams, Benewah, Boise, Bonner, Boundry, Canyon, Clearwater, Elmore, Gem, Idaho, Kooten, Latah, Lewis, Nez Perce, Owyee, Payette, Ravalli, Shoshone, Valley, Washington), Montana (counties Flathead, Lake, Lincoln, Mineral, Missoulo, Ravalli, Sanders), Oregon, Washington CPT CANADA POWER TECHNOLOGY LIMITED Mississauga 161 Watline Avenue Mississauga, Ontario L4Z−1P2 (905) 890−6900 1−800−861−9559 Edmonton 101−10411−178th Street Edmonton, Alberta T5S 1R5 (780) 453−5791 1−800−861−9559 Ville St−Laurent 234 Migneron Street Ville St−Laurent, Quebec H4T 1Y7 (514) 731−3559 1−800−861−9559 Canada FRANK EDWARDS CO. 3626 Parkway Blvd. West Valley, UT 84120 1−800−318−0201 FAX 1−801−736−8067 Colorado, Idaho (counties Bannock Bearlake, Bingham, Blaine, Booneville, Butte, Camas, Caribou, Cassia, Custer, Franklin, Fremont, Gooding, Jefferson, Jerome, Lemhi, Lincoln, Madison, Minidoka, Oneida, Power, Teton, Twin Falls) Montana (all counties except Flathead, Lake, Lincoln, Mineral, Missoulo, Ravalli, and Sanders), Utah, Wyoming GARDNER, INC. 3641 Interchange Road Columbus, OH. 43204 1−800−848−8946 FAX 1−800−626−4735 Alabama, Connecticut, Delaware, District of Columbia, Florida, Georgia, Illinois, Indiana, Kentucky, Louisiana, Maine, Maryland, Massachusetts, Michigan (except upper Peninsula), Mississippi, New Hampshire, New Jersey, New York, North Carolina, Ohio, Pennsylvania, Rhode Island, South Carolina, Tennessee, Vermont, Virgina, West Virginia Puerto Rico GULF COAST ENGINE, INC. 4202 Russell Dr. Corpus Christi, TX. 78408 1−800−825−6999 FAX 1−888−888−7036 New Mexico, Oklahoma, Texas, Mexico OSCAR WILSON ENGINE & PARTS, INC. ENGINE, INC. 826 Lone Star Drive. O’Fallon, MO 63366 1−800−873−6722 or 1−634−978−1313 FAX: 1−800−873−6720 Arkansas, Iowa, Kansas, Missouri, Nebraska WISCONSIN MAGNETO, INC. 1000 W. Donges Bay Road Suite 100 Milwaukee, WI. 53209−5920 1−800−733−7388 FAX 1−800−733−0127 Michigan (upper Peninsula), Minnesota, North Dakota, South Dakota, Wisconsin

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 24 21 22 23 25 26 27 54 29 28 53 32 33 34 35 31 36 37 38 16 39 40 41 42 50 16 16 43 44 45 16 46 47 16 16 2 48 49 70 16 30 55 57 56 51 31

Key No. Part No. Description Key No. Part No. Description 1 690566 Seat 2 028x23 Cap, Push 0n 3 094057 Spring 4 26x229 Screw 5 1001054 Bolt, Wing 6 017x47 Z Washer 7 009x56 Bolt, Shoulder 8 094154E701 Support, Seat 9 094156 Z Rod, Pivot 10 1001648E700 Bracket, Pivot 11 001x45 Bolt 12 015x89 Nut 13 009x55 Bolt, Shoulder 14 094155 Z Washer 15 164x31 Spring 16 26x249 Screw 17 26x263 Screw 18 164x30 Spring 19 1001558E245 Deck, Seat 20 15x123 Nut 21 094151E701 Plate, Index 22 009x47 Screw 23 094999 Mat, Left 24 094998 Mat, Right 25 1001797E245 Hood, W1 26 1001798E245 Grille 27 1001806 Lens 28 1001805 Housing, Headlamp 29 1001799E701 Bracket, Lower Pivot 30 690482E701 Support , Battery 31 26x270 Screw 32 26x238 Screw 33 1001491 Bearing, Steering 34 1001584E701 Dash 35 26x201 Screw 36 093007E701 Panel, Access 37 095318E701 Support, Dash 38 1001270E701 Bracket, Rear Hanger 39 094083E700 Support, Left Grille 40 094007E701 Axle, Hanger 41 094082E700 Support, Right Grille 42 009x58 Bolt, Shoulder 43 1001268E701 Frame, Right 44 1001269E701 Frame, Left 45 690424 Container, Battery 46 1001002E701 Plate, Hitch 47 690434E700 Panel, Rear 48 094610 Cover, Detent 49 015x81 Nut 50 26x277 Screw 51 15x124 Nut 53 1001802 Insert, Center Grille 54 1001803 Insert, Left Grille 55 1001804 Insert, Right Grille 56 1001800 Insert, Left Hood 57 1001801 Insert, Right Hood 59 1001755 Grommet, Parking Brake 70 1001542 Holder, Cup -- 094451 Parts Bag, Assembly -- F-050706L Instruction Book & Parts List

REPAIR PARTS MODEL 425014x92B 40 F-050706L MOTION DRIVE 1 2 3 4 5 6 7 8 9 10 12 11 13 14 15 16 60 18 19 20 17 21 62 55 22 23 25 26 27 28 30 31 32 33 35 17 41 29 17 40 39 40 38 45 37 46 49 48 50 53 51 52 47 36 8 61 43 56 44 54 54 5 5 57 34 59 42 58 37 24

15 094815 Z Nut, Adjuster 16 1001303 Z Bracket, Shift Pivot 17 26x249 Screw 18 015x84 Nut 19 094042 Z Mount, Stud Spring 20 009x54 Bolt, Shoulder 21 165x116 Spring, Extension 22 1001978E701 Bracket, Right Shifter 23 1001928E701 Frame, Right 24 002x53 Bolt, Carriage 25 1001927E701 Frame, Left 26 094045 Z Latch, Parking Brake 27 021544 Pedal 28 094038E700 Lever, Brake/Clutch 29 015x98 Nut 30 037x87 Belt, Motion Drive 31 094031 Z Yoke, Shift 32 0031x6 Pin, Hair 33 017x38 Washer 34 690369 Spacer 35 06x105 Bolt 36 † Transaxle, DANA † 37 015x88 Nut 38 020697 Key, Woodruff 39 01x155 Bolt 40 094008E701 Bracket, Transaxle 41 690409 Pulley 42 094433E700 Bracket, Transaxle Support 43 0011x7 Ring, Retainer Snap 44 095094 Pulley, Drive 45 021553 Key, Square 46 17x160 Washer 47 1401103 Z Spacer, Transaxle 48 024373 Stem, Valve 49 091923 Tire * -- 407049 Tube 50 092290-601 Wheel & Tire Assembly 51 17x195 Washer 52 0011x3 E-Ring 53 094618 Hub Cap 54 093349 Guide, Belt 55 0031x4 Pin, Hair 56 165x115 Spring, Extension 57 165x92 Spring, Extension 58 26x216 Screw 59 17x148 Washer 60 26x267 Screw 61 17x169 Washer 62 17x165 Washer * When you order a tire, make sure to give the brand name of the tire so that the tread pattern on the tire will match. † For information on Replacement Parts contact the transaxle manufacturer.

REPAIR PARTS MODEL 425014x92B 42 F-050706L STEERING 1 2 3 4 5 6 7 8 9 10 11 12 15 6 13 30 30 30 17 18 30 14 30 19 16 26 24 21 22 23 25 27 24 25 22 23 28 29 25 25 30 33 35 36 19 31 31 32 38 20 20 37 40 39 41

22 01x111 Bolt 23 17x104 Washer 24 017x53 Z Washer 25 015x84 Nut, Flange 26 1001460E245 Axle Assembly 27 095329E701 Drag Link, Left 28 094575E245 Spindle Assembly, Right 29 095328E701 Drag Link, Right 30 26x249 Screw 31 091334 Bearing, Wheel 32 024373 Stem, Valve 33 091912 Tire * -- 407047 Tube 34 1001840-601 Wheel and Tire Assembly 35 17x195 Washer 36 17x192 Washer 37 17x113 Washer 38 094618 Hub Cap (Optional) 39 26x267 Screw 40 092059 Bellows 41 1001982 Cover, Steering Wheel * When you order a tire, make sure to give the brand name of the tire so that the tread pattern on the tire will match.

1 2 3 4 5 6 7 8 14 14 9 10 11 12 12 11 13 14 15 16 17 18 19 20 20 21 22 22 23 24 24 24 25 25 11 15 27 26 26 24 25 15 33 34 36 37 32 32 38 31 24 30 25 41 43 15 30 31 44 42 24 7 40 39 39 45

Key No. Part No. Description Key No. Part No. Description 1 092698 Grip, PTO 2 094157 Z Handle, PTO 3 094022 Z Pad, Switch 4 0025x3 Bolt 5 092697 Grip, Lifter 6 166x40 Spring 7 17x103 Washer 8 690533 Lever, Lift 9 094017 Z Lever, PTO 10 009x39 Bolt, Shoulder 11 030x20 Pin, Cotter 12 017x57 Washer 13 094004 Z Link, PTO 14 015x84 Nut, Flange 15 26x249 Screw 16 166x39 Spring 17 094018E701 Bracket, PTO 18 165x119 Spring 19 690394E701 Crank, PTO 20 690212E701 Link, Lift 21 690122E701 Link, Lift Handle 22 17x168 Washer 23 017x57 Washer 24 0031x4 Pin, Hair 25 017x91 Z Washer 26 002x85 Bolt, Carriage 27 1001111E701 Lever Assembly, Lift 30 094067 Pin 31 094055E701 Bracket, Rear Suspension 32 690151 Spacer, Lifter 33 009x53 Bolt, Shoulder 34 094015E701 Bracket, Pivot 36 17x191 Washer 37 015x84 Nut, Flange 38 165x131 Spring 39 015x68 Nut, Flange 40 094005E700 Bracket, PTO 41 094027E701 Hanger, Left Deck 42 094026E701 Hanger, Right Deck 43 094158 Z Rod, Hanger 44 690539E701 Bracket, Suspension 45 1001098E701 Plate, Stiffening

REPAIR PARTS MODEL 425014x92B 46 F-050706L MOWER HOUSING 1 2 3 61 2 1 4 5 11 10 47 13 7 15 16 17 18 23 22 9 19 8 20 5 21 23 23 24 12 27 25 24 28 22 5 26 5 24 21 20 52 8 19 5 22 11 10 17 13 47 9 7 29 5 33 31 32 30 22 22 5 33 55 32 53 50 51 50 51 53 54 33 33 32 5 44 42 42 34 43 41 36 37 38 39 40 38 39 40 37 35 36 14 34 5 33 33 59 45 32 17 22 46 17 48 15 22 57 58 60 60 49 5 23 62 17 22

4 690387 Pulley, Idler 5 015x84 Nut, Flange 7 009x51 Bolt, Shoulder 8 690212E701 Link, Lift 9 094137 Pad, Friction 10 009x52 Bolt, Shoulder 11 094055E701 Bracket, Suspension 12 094049E701 Pad Assembly, Left Brake 13 094068 Knob 14 009x58 Bolt, Shoulder 15 094128E701 Plate, Suspension 16 166x43 Spring 17 015x79 Nut, Flange 18 094192E701 Bracket, Suspension 19 095194 Pin, Hanger 20 017x91 Washer 21 0031x4 Pin, Hair 22 0025x7 Bolt 23 094051E701 Cover, Pulley 24 009x39 Bolt, Shoulder 25 690408E700 Arm, Idler 26 166x41 Spring 27 094047E701 Pad Assembly, Right Brake 28 094193E701 Bracket, Brake 29 166x42 Spring 30 094191E701 Bracket, Suspension 31 092426E701 Plate 32 015x88 Nut, Flange 33 002x53 Bolt, Carriage 34 1001200 Mandrell Housing 35 690539E701 Bracket, Suspension 36 690411 Adapter, Blade 37 095100E701 Blade 38 17x166 Washer 39 17x165 Washer 40 15x100 Nut 41 0166x4 Spring 42 028x23 Cap, Push On 43 094957 Z Rod, Deflector 44 094707SE Deflector Assembly 45 094956E701 Bracket, Deflector Hinge 46 094190E701 Bracket, Front Hanger 47 017x45 Washer 48 094781 Guide, Belt 49 690369 Spacer 50 094025 Bolt, Axle 51 017x91 Washer 52 165x119 Spring, Extension 53 092683 Wheel, Gage 54 1001260E701 Bracket, Right Wheel 55 092423E701 Bracket, Left Wheel 56 009x52 Bolt, Shoulder 57 26x249 Screw 58 094604E701 Stiffener 59 094814E701 Housing, Blade * 60 031x11 Ring, Locking 61 015x98 Nut, Flange 1-61 7601032 Complete Mower Housing Assy. 62 094066 Guide, Belt * Includes Key No. 17, 18, 30, 31, 32, 33, 45, 46, 53, 54, 55, and 56. * This part is included when ordering Key number 34.

REPAIR PARTS MODEL 425014x92B 48 F-050706L ENGINE MOUNT 1 6 7 8 9 10 11 12 13 14 15 15 21 22 22 21 2 3 4 5 26 30 31 9f 9a 9d 9b 9b 9c 23 23 9e 32

2 690280 Fuel Tank 3 095197 Hose Clamp ** 4 7601033 Fuel Line (Must cut to length) ** 5 095197 Hose Clamp ** 6 26x201 Screw 7 094006E700 Plate, Engine 8 092371 Throttle Control 9 * Engine, BRIGGS & STRATTON 9a 1001717 Muffler 9b 091309 Gasket, Muffler 9c 095207 Adapter, Muffler 9d 06x103 Screw, Adapter 9e 009x59 Bolt, Muffler 9f 092378 Lock, Screw 10 0025x7 Bolt, Engine Mount 11 690439 Z Stack Pulley Assembly 12 019x35 Lockwasher 13 01x140 Bolt, Hex 14 17x170 Washer 15 26x249 Screw 21 094384 Guide, Belt 22 015x79 Z Nut, Flange 23 094066 Guide, Belt 26 26x253 Screw 30 1001897 Shield, Heat 31 26x263 Screw 32 06x104 Screw * For information on Replacement Parts for this engine contact the manufacturer. * * These parts are included with Key number 2.

*AFTERFIRE SOLENOID OPTIONAL WIRING HARNESS FOR: MAIN HARNESS: 250x138 SEAT : 250x139; LIGHT : 250x92 1001575 1001575 1 3 5 6 8 9 7 10 11 2 12 4 12

1001716 Socket, Light 090084 Bulb, Light 2 250x138 Harness, Chassis Wire 3 1001993 Switch, Ignition 020729 Key, Ignition 091489 Nut, Hex 091488 Cap, Ignition 4 094136 Switch, Limit (PTO) 5 302031 Fuse 407078 Holder, Fuse 6 1002004 Solenoid 26x229 Screw, Mounting 15x116 Locknut 7 024x32 Cable, Battery Ground 26x229 Screw, Ground Cable 8 021075 Battery 002x82 Bolt, Carriage 014x79 Wingnut 9 250x139 Harness, Seat Switch Wire 10 094159 Switch, Seat Sensor 11 024x31 Cable 12 1001575 Switch, Select Reverse� / Clutch Brake

Clutch, 24 Drive Brake, 24 Mower Housing, Level, 29 Shift Lever, 25 Attachments, 15, 56 B Battery Charge, 25 Check, 12 Clean, 25 Install, 12 Removal, 25 Storage, 34 Belt Motion Drive Adjust, 24 Replace, 30 Mower Drive Adjust, 23 Replace, 32 Blade Inspect, 22 Remove And Install, 22 Sharpen, 22 Blade Rotation Control Adjust, 23 Location, 14 Operation, 16 C Clutch Adjust, 24 Check, 24 Clutch / Brake Pedal, Location, 14 Controls, Location, 14 Cutting Height Adjust, 29 Change, 17 D Drive Brake Adjust, 24 Check, 24 E Electrical Safety System, 15 Engine Fuel, 13, 19 Oil, 13, 19 Preparation, 13 Spark Arrester, 13, 21 Starting, 19 Storage, 34 Throttle Control, 15 F Filter, Fuel, 26 Fuel, Type, 19 Fuse, 34 H Headlight, Replace Light Bulb, 34 Headlight Switch, Location, 14 I Ignition Key Switch, Operation, 15 Ignition Switch, Location, 14 L Lift Lever Location, 14 Operation, 17 Lubrication, Mower, 26 M Maintenance Adjust, Guage Wheels, 28 Battery Charge, 25 Clean, 25 Belt Motion Drive, 30 Mower Drive, 32 Blade, 22 Blade Rotation Control, 23 Clutch, 24 Drive Brake, 24 Filter, Fuel, 26 Fuse, 34 Headlight, 34 Install, Wheels, 33 Lubrication, 26 Mower Housing Clean, 34 Install, 27 Level, 29 Remove, 27 Muffler, 21 Storage, 34 Maintenance Chart, 21 Motion Drive Belt Adjust, 24 Replace, 30 Mower Drive Belt Adjust, 23 Replace, 32 Mower Housing Clean, 34 Cutting Height, 17 Install, 27 Level Adjustment, 29 Operation, 18 Remove, 27 Muffler, 21 Spark Arrester, 21 O Oil Check, 19 Type, 19 Operation Attachments, 15 Blade Rotation Control, 14, 16 Clutch / Brake Pedal, 14 Headlight Switch, 14 Ignition Key Switch, 15 Ignition Switch, 14 Lift Lever, 14, 17 Location Of Controls, 14 Mower Housing, 18 Mowing And Bagging, 20 Operate On Hills, 18 Parking Brake, 14, 17 Shift Lever, 14, 16 Start The Engine, 19 Stop The Unit, 17 Throttle Control, 14, 15 Transport, 17 P Parking Brake Location, 14 Operation, 17 Parts Bag, 10 S Safety Rules American National Standard Institute, 3–4 Safe Mowing Guide, 5–7 Seat, Install, 11 Shift Lever Adjust, 25 Location, 14 Operation, 16 Slope Guide, 54 Spark Arrester, 13, 21 Steering Wheel, 11 Storage, 34 T Throttle Control Location, 14 Operation, 15 Tire Pressure, 13, 26 Trouble Shooting Chart, 35 W Warranty, 2

Make your Lawn Tractor do more than you ever imagined. The accessories shown on this page can be used on your Lawn Tractor. See the Store or Dealer where you purchased your Lawn Tractor. If you are unable to obtain the necessary information, contact the Central Parts Distribution Center for your area as listed in your Repair Parts Book. Î Î LAWN SWEEPER Model No. 24720 SNOW BLADE Model No. 24478 SNOW THROWER Model No. 24583 38” MULCHER KIT Model No. 24750 40” MULCHER KIT Model No. 24755 42” MULCHER KIT Model No. 24758 TIRE CHAINS Model No. 24530 (For 18x8.5 inch tire) Model No. 24538 (For 18x9.5 inch tires) Model No. 24525 (For 20x8 inch tire) Model No. 24515 (For 20x10 inch tire) Model No. 24539 (For 23x9.5 inch tire) GRASS BAGGER Model No. 24767 9 Bushel Capacity (For 42” and 46”) REAR WHEEL WEIGHTS Model No. 24003 (For 18x9.5 inch tires) (For 20x8 inch tires) Model No. 24630 (For 23 inch tires) GARDEN TILLER Model No. 13460 GRASS BAGGER Model No. 24744 7 Bushel Capacity (For 38”, 40”, and 42”)