Opel ASTRA Owner's Manual

In brief ............................................ 6 Keys, doors and windows ............ 23 Seats, restraints ........................... 40 Storage ........................................ 62 Instruments and controls ........... 102 Lighting ...................................... 139 Climate control ........................... 152 Driving and operating ................. 161 Vehicle care ............................... 221 Service and maintenance .......... 280 Technical data ........................... 283 Customer information ................ 322 Index .......................................... 324 Contents

Please enter your vehicle's data on the previous page to keep it easily accessible. This information is available in the sections "Service and maintenance" and "Technical data" as well as on the identification plate. Introduction Your vehicle is a designed combination of advanced technology, safety, environmental friendliness and economy. This Owner's Manual provides you with all the necessary information to enable you to drive your vehicle safely and efficiently. Make sure your passengers are aware of the possible risk of accident and injury which may result from improper use of the vehicle. You must always comply with the specific laws and regulations of the country that you are in. These laws may differ from the information in this Owner's Manual. When this Owner's Manual refers to a workshop visit, we recommend your Opel Service Partner. For gas vehicles we recommend an Opel Repairer authorised for servicing gas vehicles. All Opel Service Partners provide first-class service at reasonable prices. Experienced mechanics trained by Opel work according to specific Opel instructions. The customer literature pack should always be kept ready to hand in the vehicle. Using this manual ■ This manual describes all options and features available for this model. Certain descriptions, including those for display and menu functions, may not apply to your vehicle due to model variant, country specifications, special equipment or accessories. ■ The "In brief" section will give you an initial overview. ■ The table of contents at the beginning of this manual and within each section shows where the information is located. ■ The index will enable you to search for specific information. ■ This Owner's Manual depicts left- hand drive vehicles. Operation is similar for right-hand drive vehicles. ■ The Owner's Manual uses the factory engine designations. The corresponding sales designations can be found in the section "Technical data". ■ Directional data, e.g. left or right, or front or back, always relate to the direction of travel. ■ The vehicle display screens may not support your specific language. ■ Display messages and interior labelling are written in bold letters.

Cautions 9 Danger Text marked 9 Danger provides information on risk of fatal injury. Disregarding this information may endanger life. 9 Warning Text marked 9 Warning provides information on risk of accident or injury. Disregarding this information may lead to injury. Caution Text marked Caution provides information on possible damage to the vehicle. Disregarding this information may lead to vehicle damage. Symbols Page references are indicated with 3. 3 means "see page". We wish you many hours of pleasurable driving. Adam Opel AG

Vehicle unlocking Press button c to unlock the doors and load compartment. Open the doors by pulling the handles. 5-door hatchback, Sports tourer To open the tailgate, push the touchpad switch below the emblem.

emblem at the bottom half. Press button x on remote control to unlock and open the tailgate while the doors remain locked. 4-door notchback Press button x on the remote control for at least 2 seconds, the boot lid opens slightly. Radio remote control 3 23, Central locking system 3 25, Load compartment 3 28. Seat adjustment Seat positioning Pull handle, slide seat, release handle. Seat position 3 42, Seat adjustment 3 42. 9 Danger Do not sit nearer than 25 cm from the steering wheel, to permit safe airbag deployment.

release lever. Allow the seat to engage audibly. Seat position 3 42, Seat adjustment 3 42, Seat folding 3 45. Seat height Lever pumping motion up = seat higher down = seat lower Seat position 3 42, Seat adjustment 3 42. Seat inclination Lever pumping motion up = front end higher down = front end lower Seat position 3 42, Seat adjustment 3 42.

Operate switch 1: forwards/ backwards = lengthwise adjustment upwards/ downwards = height adjustment upwards/ downwards at front = inclination adjustment Operate switch 2: forwards/ backwards at the top = backrest adjustment Power seat adjustment 3 46. Seat folding 3 45. Head restraint adjustment Press release button, adjust height, engage. Head restraints 3 40.

belt buckle. The seat belt must not be twisted and must fit close against the body. The backrest must not be tilted back too far (maximum approx. 25 °). To release belt, press red button on belt buckle. Seat position 3 42, Seat belts 3 49, Airbag system 3 52. Mirror adjustment Interior mirror To reduce dazzle, adjust the lever on the underside of the mirror housing. Interior mirror 3 34, Automatic anti- dazzle interior mirror 3 34. Exterior mirrors Select the relevant exterior mirror and adjust it. Convex exterior mirrors 3 33, Electric adjustment 3 33, Folding exterior mirrors 3 33, Heated exterior mirrors 3 34.

Unlock the lever, adjust the steering wheel, then engage the lever and ensure it is fully locked. Do not adjust the steering wheel unless the vehicle is stationary and the steering wheel lock has been released. Airbag system 3 52, Ignition positions 3 162.

2 Exterior mirrors ..................... 33 3 Cruise control ..................... 180 Speed limiter ....................... 181 Adaptive cruise control ....... 183 Forward collision alert ......... 189 4 Side air vents ...................... 159 5 Turn and lane-change signals, headlight flash, low beam and high beam, high beam assist ................. 146 Exit lighting ......................... 150 Parking lights ...................... 147 Buttons for Driver Information Centre .............. 120 6 Instruments ........................ 109 7 Steering wheel controls ..... 102 8 Driver Information Centre .... 120 9 Windscreen wiper, windscreen washer system, headlight washer system, rear wiper, rear washer system .................... 104 10 Sport mode ........................ 177 Central locking system .......... 25 Fuel selector ....................... 110 Hazard warning flashers .... 146 Control indicator for airbag deactivation ........................ 114 Control indicator for front passenger seat belt ........... 114 Tour mode .......................... 177 11 Info-Display ........................ 124 12 Anti-theft alarm system status LED ........................... 30 13 Centre air vents .................. 159 14 Glovebox .............................. 62 15 Traction Control system ..... 175 Electronic Stability Control . 176 Parking assist ..................... 195 Advanced parking assist ..... 198 Lane departure warning ..... 208 Eco button for stop/start system ................................. 164 Unlock button for boot lid ...... 28 16 Climate control system ........ 152 17 AUX input, USB input, SD card slot ................................ 12 18 Power outlet ........................ 108 19 Selector lever, manual transmission ....................... 171 Automatic transmission ...... 168 20 Electrical parking brake ...... 173 21 Ignition switch with steering wheel lock ............ 162 22 Horn ................................... 103 Driver airbag ........................ 53 23 Bonnet release lever .......... 223 24 Storage compartment, fuse box ............................. 251 25 Steering wheel adjustment 102 26 Light switch ........................ 139 Headlight range adjustment ......................... 141 Front fog lights ................... 146

7 = lights off 8 = sidelights 9 = low beam Automatic light control AUTO = automatic light control: exterior lighting is switched on and off automatically m = activation or deactivation of the automatic light control 8 = sidelights 9 = low beam Fog lights Press light switch: > = front fog lights r = rear fog light Lighting 3 139. Headlight flash, high beam and low beam headlight flash = pull lever high beam = push lever low beam = push or pull lever Automatic light control 3 140, High beam 3 140, Headlight flash 3 141, Adaptive forward lighting 3 142.

lever up = right turn signal lever down = left turn signal Turn and lane-change signals 3 146, Parking lights 3 147. Hazard warning flashers Operated with the ¨ button. Hazard warning flashers 3 146. Horn Press j.

Windscreen wiper 2 = fast 1 = slow P = interval wiping or automatic wiping with rain sensor § = off For a single wipe when the windscreen wiper is off, press the lever down. Windscreen wiper 3 104, Wiper blade replacement 3 228. Windscreen and headlight washer Pull lever. Windscreen and headlight washer system 3 104, Washer fluid 3 225. Rear window wiper Press the rocker switch to activate the rear window wiper: upper switch = continuous operation lower switch = intermittent operation middle position = off

Push lever. Washer fluid is sprayed on the rear window and the wiper wipes a few times. Rear window wiper/washer 3 106. Climate control Heated rear window, heated exterior mirrors The heating is operated by pressing the Ü button. Heated rear window 3 37. Demisting and defrosting the windows Press button V. Set the temperature control to the highest level. Cooling n on. Heated rear window Ü on. Climate control system 3 152.

wait 3 seconds after depressing clutch pedal and then press the release button on the selector lever and engage the gear. If the gear does not engage, set the lever to neutral, release the clutch pedal and depress again; then repeat gear selection. Manual transmission 3 171. Automatic transmission P = park R = reverse N = neutral D = drive Manual mode: move selector lever from D to the left. < = higher gear ] = lower gear The selector lever can only be moved out of P when the ignition is on and the brake pedal is applied. To engage P or R, press the release button. Automatic transmission 3 168. Starting off Check before starting off ■ Tyre pressure and condition 3 257, 3 310. ■ Engine oil level and fluid levels 3 223. ■ All windows, mirrors, exterior lighting and number plates are free from dirt, snow and ice and are operational. ■ Proper position of mirrors, seats, and seat belts 3 33, 3 42, 3 50. ■ Brake function at low speed, particularly if the brakes are wet.

■ Turn key to position 1 ■ move the steering wheel slightly to release the steering wheel lock ■ operate clutch and brake ■ automatic transmission in P or N ■ do not operate accelerator pedal ■ diesel engines: turn the key to position 2 for preheating and wait until control indicator ! extinguishes ■ turn key to position 3 and release Starting the engine 3 162. Stop-start system If the vehicle is at a low speed or at a standstill and certain conditions are fulfilled, activate an Autostop as follows: ■ Depress the clutch pedal ■ set the lever in neutral ■ release the clutch pedal An Autostop is indicated by the needle at the AUTOSTOP position in the tachometer. To restart the engine, depress the clutch pedal again. Stop-start system 3 164. Parking ■ Always apply the parking brake. Activate the manual parking brake without pressing the release button. Apply as firmly as possible on a downhill slope or uphill slope. Depress foot brake at the same time to reduce operating force. For vehicles with electrical parking brake, pull switch m for approx. one second. ■ Switch off the engine. Turn the ignition key to position 0 and remove it. Turn the steering wheel until the steering wheel lock is felt to engage. For vehicles with automatic transmission, the key can only be removed when the selector lever is in the P position. ■ If the vehicle is on a level surface or uphill slope, engage first gear or set the selector lever to P before switching off the ignition. On an uphill slope, turn the front wheels away from the kerb.

engage reverse gear or set the selector lever to P before switching off the ignition. Turn the front wheels towards the kerb. ■ Lock the vehicle with button e on the radio remote control. Activate the anti-theft alarm system 3 30. ■ Do not park the vehicle on an easily ignitable surface. The high temperature of the exhaust system could ignite the surface. ■ Close the windows and the sunroof. ■ The engine cooling fans may run after the engine has been switched off 3 222. ■ After running at high engine speeds or with high engine loads, operate the engine briefly at a low load or run in neutral for approx. 30 seconds before switching off, in order to protect the turbocharger. Keys, locks 3 23, Laying the vehicle up for a long period of time 3 221.

23 Keys, doors and windows Keys, locks ................................... 23 Doors ........................................... 28 Vehicle security ............................ 30 Exterior mirrors ............................ 33 Interior mirrors ............................. 34 Windows ...................................... 35 Roof ............................................. 38 Keys, locks Keys Replacement keys The key number is specified in the Car Pass or on a detachable tag. The key number must be quoted when ordering replacement keys as it is a component of the immobiliser system. Locks 3 276. Key with foldaway key section Press button to extend. To fold the key, first press the button. Car Pass The Car Pass contains security related vehicle data and should therefore be kept in a safe place. When the vehicle is taken to a workshop, this vehicle data is needed in order to perform certain operations. Radio remote control

Used to operate: ■ Central locking system ■ Anti-theft locking system ■ Anti-theft alarm system ■ Power windows ■ Sunroof The radio remote control has an approximate range of up to 20 metres. It can be restricted by external influences. The hazard warning flashers confirm operation. Handle with care, protect from moisture and high temperatures and avoid unnecessary operation. Fault If the central locking system cannot be operated with the radio remote control, it may be due to the following: ■ Range exceeded ■ Battery voltage too low ■ Frequent, repeated operation of the radio remote control while not in range, which will require re- synchronisation ■ Overload of the central locking system by operating at frequent intervals, the power supply is interrupted for a short time ■ Interference from higher-power radio waves from other sources Unlocking 3 25. Basic settings Some settings can be changed in the menu Settings in the Info-Display. Vehicle personalisation 3 133. Radio remote control battery replacement Replace the battery as soon as the range reduces. Batteries do not belong in household waste. They must be disposed of at an appropriate recycling collection point. Key with foldaway key section Extend the key and open the unit. Replace the battery (battery type CR 2032), paying attention to the installation position. Close the unit and synchronise. Radio remote control synchronisation After replacing the battery, unlock the door with the key in the driver's door lock. The radio remote control will be synchronised when you switch on the ignition.

25 Memorised settings Whenever the key is removed from the ignition switch, the following settings are automatically memorised by the key: ■ Lighting ■ Infotainment system ■ Central locking system ■ Sport mode settings ■ Comfort settings The saved settings are automatically used the next time the memorised key is inserted into the ignition switch and turned to position 1 3 162. A precondition is that Personalization by driver is activated in the personal settings of the Graphic-Info-Display. This must be set for each key used. On vehicles equipped with Colour-Info-Display, the personalisation is permanently activated. Vehicle personalisation 3 133. Central locking system Unlocks and locks doors, load compartment and fuel filler flap. A pull on an interior door handle unlocks the respective door. Pulling the handle once more opens the door. Note In the event of an accident in which airbags or belt pretensioners are deployed, the vehicle is automatically unlocked. Note A short time after unlocking with the remote control the doors are locked automatically if no door has been opened. Unlocking Press button c. Two settings are selectable: ■ To unlock only the driver's door, load compartment and fuel filler flap, press button c once. To unlock all doors, press button c twice or ■ press button c once to unlock all doors, load compartment and fuel filler flap The setting can be changed in the menu Settings in the Info-Display. Vehicle personalisation 3 133.

The setting can be saved for the key being used. Memorised settings 3 25. Unlocking and opening the tailgate 3 28. Locking Close doors, load compartment and fuel filler flap. Press button e. If the driver's door is not closed properly, the central locking system will not work. Central locking buttons Locks or unlocks all doors, the load compartment and fuel filler flap from inside the passenger compartment. Press the e button to lock. Press the c button to unlock. Fault in radio remote control system Unlocking Manually unlock the driver's door by turning the key in the lock. Switch on the ignition and press the central locking button c to unlock the other doors, load compartment and fuel filler flap. By switching on the ignition, the anti-theft locking system is deactivated. Locking Manually lock the driver's door by turning the key in the lock.

27 Fault in central locking system Unlocking Manually unlock the driver's door by turning the key in the lock. The other doors can be opened by pulling the interior handle twice. The load compartment and fuel filler flap cannot be opened. To deactivate the anti-theft locking system, switch on the ignition 3 30. Locking Push inside locking knob of all doors except driver's door. Then close the driver's door and lock it from the outside with the key. The fuel filler flap and tailgate cannot be locked. Automatic locking This security feature can be configured to automatically lock all doors, load compartment and fuel filler flap as soon as a certain speed is exceeded. Additionally it is configurable to unlock the driver's door or all doors after the ignition is switched off and the ignition key is removed (manual transmission) or the selector lever is moved to P position (automatic transmission). Settings can be changed in the menu Settings in the Info-Display. Vehicle personalisation 3 133. The settings can be saved for the key being used 3 25. Child locks 9 Warning Use the child locks whenever children are occupying the rear seats. Using a key or suitable screwdriver, turn the child lock in the rear door to the horizontal position. The door cannot be opened from the inside. For deactivation turn the child lock to the vertical position.

Doors Load compartment Tailgate Opening 5-door hatchback After unlocking, push the touchpad switch below the emblem and open the tailgate. 3-door hatchback Press button x on radio remote control or push the brand emblem at the bottom half to unlock and open the tailgate. Pressing button x opens the tailgate even if the doors are locked. Sports tourer After unlocking, push the touchpad switch under the tailgate moulding and open the tailgate. Central locking system 3 25.

29 4-door notchback To unlock the boot lid, press button x on the remote control for at least 2 seconds, or, to open from the inside, press button x in the centre console, the boot lid is opened slightly. With the doors centrally locked, the boot lid cannot be opened with button x in the centre console. Closing Use one of the interior handles. Do not push the touchpad switch or the emblem whilst closing as this will unlock the tailgate again. Central locking system 3 25.

General hints for operating tailgate 9 Warning Do not drive with the tailgate open or ajar, e.g. when transporting bulky objects, since toxic exhaust gases, which can not be seen or smelled, could enter the vehicle. This can cause unconsciousness and even death. Caution Before opening the tailgate check overhead obstructions, such as a garage door, to avoid damage to the tailgate. Always check the moving area above and behind the tailgate. Note The installation of certain heavy accessories onto the tailgate may affect its ability to remain open. Vehicle security Anti-theft locking system 9 Warning Do not use the system if there are people in the vehicle! The doors cannot be unlocked from the inside. The system deadlocks all the doors. All doors must be closed otherwise the system cannot be activated. If the ignition was on, the driver's door must be opened and closed once so that the vehicle can be secured. Unlocking the vehicle disables the mechanical anti-theft locking system. This is not possible with the central locking button. Activating Press e on the radio remote control twice within 15 seconds. Anti-theft alarm system The anti-theft alarm system is combined with the anti-theft locking system. It monitors: ■ Doors, tailgate, bonnet ■ Passenger compartment including adjoining load compartment ■ Vehicle inclination, e.g. if it is raised ■ Ignition

31 Activation ■ Self-activated 30 seconds after locking the vehicle (initialisation of the system) ■ Directly by pressing e on the radio remote control once more after locking Note Changes to the vehicle interior such as the use of seat covers, and open windows or sunroof, could impair the function of passenger compartment monitoring. Activation without monitoring of passenger compartment and vehicle inclination Switch off the monitoring of passenger compartment and vehicle inclination when animals are being left in the vehicle, because of high volume ultrasonic signals or movements triggering the alarm. Also switch off when the vehicle is on a ferry or train. 1. Close tailgate, bonnet, windows and sunroof. 2. Press button o. LED in the button o illuminates for a maximum of 10 minutes. 3. Close doors. 4. Activate the anti-theft alarm system. Status message is displayed in the Driver Information Centre. Status LED Status LED is integrated in the sensor on top of the instrument panel.

Status during the first 30 seconds of anti-theft alarm system activation: LED illuminates = test, arming delay. LED flashes quickly = doors, tailgate or bonnet not completely closed, or system fault. Status after system is armed: LED flashes slowly = system is armed. Seek the assistance of a workshop in the event of faults. Deactivation Unlocking the vehicle deactivates the anti-theft alarm system. Alarm When triggered, the alarm sounds via a separate battery-backed power sounder, and the hazard warning lights flash simultaneously. The number and duration of alarm signals are stipulated by legislation. The alarm can be silenced by pressing any button on the radio remote control or by switching on the ignition. The anti-theft alarm system can be deactivated only by pressing button c or by switching on the ignition. A triggered alarm, which has not been interrupted by the driver, will be indicated by the hazard warning lights. They will flash quickly three times when the vehicle is unlocked next time with the radio remote control. Additionally a warning message or a warning code is displayed in the Driver Information Centre after switching on the ignition. Vehicle messages 3 127. Immobiliser The system is part of the ignition switch and checks whether the vehicle is allowed to be started with the key being used. The immobiliser is activated automatically after the key has been removed from the ignition switch. If the control indicator d flashes when the ignition is on, there is a fault in the system; the engine cannot be started. Switch off the ignition and repeat the start attempt. If the control indicator continues flashing, attempt to start the engine using the spare key and seek the assistance of a workshop. Note The immobiliser does not lock the doors. You should always lock the vehicle after leaving it and switch on the anti-theft alarm system 3 25, 3 30. Control indicator d 3 119.

33 Exterior mirrors Convex shape The convex exterior mirror contains an aspherical area and reduces blind spots. The shape of the mirror makes objects appear smaller, which will affect the ability to estimate distances. Electric adjustment Select the relevant exterior mirror by turning the control to left (L) or right (R). Then swivel the control to adjust the mirror. In position 0 no mirror is selected. Folding For pedestrian safety, the exterior mirrors will swing out of their normal mounting position if they are struck with sufficient force. Reposition the mirror by applying slight pressure to the mirror housing. Electric folding Turn control to 0, then push the control down. Both exterior mirrors will fold. Push the control down again - both exterior mirrors return to their original position. If an electrically folded mirror is manually extended, pressing down the control will only electrically extend the other mirror.

Heated mirrors Operated by pressing the Ü button. Heating works with the engine running and is switched off automatically after a short time. Interior mirrors Manual anti-dazzle To reduce dazzle, adjust the lever on the underside of the mirror housing. Automatic anti-dazzle Dazzle from following vehicles at night is automatically reduced.

35 Windows Windscreen Heat-reflecting windscreen The heat-reflecting windscreen has a coating which reflects solar radiation. Also data signals, e.g. from toll stations, might be reflected. The marked areas on the windscreen are not covered with the coating. Devices for electronic data recording and fee payment must be attached in these areas. Otherwise data recording malfunctions may occur. Windscreen stickers Do not attach stickers such as toll road stickers or similar on the windscreen in the area of the interior mirror. Otherwise the detection zone of the sensor and the view area of the camera in the mirror housing could be restricted. Manual windows The door windows can be opened or closed with the window winders. Power windows 9 Warning Take care when operating the power windows. Risk of injury, particularly to children. If there are children on the rear seats, switch on the child safety system for the power windows. Keep a close watch on the windows when closing them. Ensure that nothing becomes trapped in them as they move. Switch on ignition to operate power windows. Retained power off 3 162. Operate the switch for the respective window by pushing to open or pulling to close. Pushing or pulling gently to the first detent: window moves up or down as long as the switch is operated.

Pushing or pulling firmly to the second detent and then releasing: window moves up or down automatically with safety function enabled. To stop movement, operate the switch once more in the same direction. Safety function If the window glass encounters resistance above the middle of the window during automatic closing, it is immediately stopped and opened again. Override safety function In the event of closing difficulties due to frost or the like, switch on the ignition, then pull the switch to the first detent and hold. The window moves up without safety function enabled. To stop movement, release the switch. Child safety system for rear windows Press switch z to deactivate rear door power windows, the LED illuminates. To activate, press z again. Operating windows from outside The windows can be operated remotely from outside the vehicle. Press and hold c button to open windows. Press and hold e button to close windows. Release button to stop window movement. If the windows are fully opened or closed, the hazard warning lights will flash twice. Overload If the windows are repeatedly operated within short intervals, the window operation is disabled for some time.

37 Initialising the power windows If the windows cannot be closed automatically (e.g. after disconnecting the vehicle battery), a warning message or a warning code is displayed in the Driver Information Centre. Vehicle messages 3 127. Activate the window electronics as follows: 1. Close doors. 2. Switch on ignition. 3. Pull switch until the window is closed and keep pulling for additional 2 seconds. 4. Repeat for each window. Heated rear window Operated by pressing the Ü button. Heating works with the engine running and is switched off automatically after a short time. Sun visors The sun visors can be folded down or swivelled to the side to prevent dazzling. If the sun visors have integral mirrors, the mirror covers should be closed when driving. A ticket holder is located on the backside of the sun visor.

Roof Sunroof 9 Warning Take care when operating the sunroof. Risk of injury, particularly to children. Keep a close watch on the movable parts when operating them. Ensure that nothing becomes trapped in them as they move. Switch on ignition to operate the sunroof. Open or close Press p or r gently to the first detent: sunroof is opened or closed with safety function enabled as long as the switch is operated. Press p or r firmly to the second detent and then release: the sunroof is opened or closed automatically with safety function enabled. To stop movement, operate the switch once more. Raise or close Press q or r: sunroof is raised or closed automatically with safety function enabled. If the sunroof is raised, it can be opened in one step by pressing p. Sunblind The sunblind is manually operated. Close or open the sunblind by sliding. When the sunroof is open, the sunblind is always open. General hints Safety function If the sunroof encounters resistance during automatic closing, it is immediately stopped and opened again. Override safety function In the event of closing difficulties due to frost or the like, hold the switch r pressed to the second detent. The sunroof closes without safety function enabled. To stop movement, release the switch.

39 Closing sunroof from outside The sunroof can be closed remotely from outside the vehicle. Press and hold e button to close the sunroof. Release the button to stop the movement. Initialising after a power failure After a power failure, it may only be possible to operate the sunroof to a limited extent. Have the system initialised by your workshop. Glass panel Panorama roof Turn the handle and move the roof cover to a suitable position. The roof cover engages in position after releasing the handle. Note Close the sun visors before sliding the roof lining.

Front seats ................................... 42 Rear seats ................................... 49 Seat belts ..................................... 49 Airbag system .............................. 52 Child restraints ............................. 56 Head restraints Position 9 Warning Only drive with the head restraint set to the proper position. The upper edge of the head restraint should be at upper head level. If this is not possible for extremely tall people, set to highest position, and set to lowest position for small people. Adjustment Head restraints on front seats Height adjustment Press release button, adjust height, engage.

restraint forwards. It engages in several positions. To return to its rearmost position, pull fully forwards and release. Head restraints on rear seats Height adjustment Pull the head restraint upwards or press the catch to release and push the head restraint downwards. Removal Press both catches, pull the head restraint upwards and remove. Active head restraints In the event of a rear-end impact, the front parts of the active head restraints are moved slightly forwards. Thus the head is supported so that the risk of whiplash injury is reduced. Note Approved accessories may only be attached if the seat is not in use.

adjusted. ■ Sit with buttocks as far back against the backrest as possible. Adjust the distance between the seat and the pedals so that legs are slightly angled when pressing the pedals. Slide the front passenger seat as far back as possible. ■ Sit with shoulders as far back against the backrest as possible. Set the backrest rake so that it is possible to easily reach the steering wheel with arms slightly bent. Maintain contact between shoulders and the backrest when turning the steering wheel. Do not angle the backrest too far back. We recommend a maximum rake of approx. 25°. ■ Adjust the steering wheel 3 102. ■ Set seat height high enough to have a clear field of vision on all sides and of all display instruments. There should be at least one hand of clearance between head and the roof frame. Your thighs should rest lightly on the seat without pressing into it. ■ Adjust the head restraint 3 40. ■ Adjust the height of the seat belt 3 50. ■ Adjust the thigh support so that there is a space approx. two fingers wide between the edge of the seat and the hollow of the knee. ■ Adjust the lumbar support so that it supports the natural shape of the spine. Seat adjustment 9 Danger Do not sit nearer than 25 cm from the steering wheel, to permit safe airbag deployment. 9 Warning Never adjust seats while driving as they could move uncontrollably.

the seats. Drive only with engaged seats and backrests. Seat positioning Pull handle, slide seat, release handle. Seat backrests Pull lever, adjust inclination and release lever. Allow the backrest to engage audibly. Seat height Lever pumping motion up = seat higher down = seat lower

up = front end higher down = front end lower Lumbar support Adjust lumbar support using the four- way switch to suit personal requirements. Moving support up and down: push switch up or down. Increasing and decreasing support: push switch forwards or backwards. Adjustable thigh support Pull the lever and slide the thigh support.

Adjust seat width and backrest width using the switches to suit personal requirements. Operate front rocker switch to change seat width. Opeate rear rocker switch to change backrest width. Seat folding Caution When seat height is in highest position, push head restraints down and lift up sun visors before folding backrest forwards. Seat folding on manual operated seats Lift release lever and fold backrest forwards. Slide seat forwards. To restore, slide the seat backwards. Move the backrest against the resistance to the upright position and engage. The memory function allows the seat to engage in its original position. Do not operate backrest inclination lever while backrest is tilted forward. Vehicles with panorama roof: to tilt backrest forward, push head restraints down and lift up sun visors. The illustration shows the release lever on OPC seat.

position before folding to avoid injury. Seat folding on power seats Lift release lever and fold backrest forwards. The seat slides automatically forwards to the stop. To restore lift backrest to upright position and engage. The seat slides automatically backwards to the original position. In case the head restraint of the folded backrest is blocked by the upper windscreen frame, slightly let the seat move backwards before lifting up the backrest 3 46. Safety function If the power seat encounters resistance while sliding forward or rearward, it is immediately stopped and moved back. Overload If the folding function is electrically overloaded, the power supply is automatically cut-off for a short time. Power seat adjustment 9 Warning Care must be taken when operating the power seats. There is a risk of injury, particularly for children. Objects could become trapped. Keep a close watch on the seats when adjusting them. Vehicle passengers should be informed accordingly. Seat lengthwise position Move switch forwards/backwards.

Seat inclination Move front of switch upwards/ downwards. Seat backrests Turn switch forwards/backwards.

way switch to suit personal requirements. Moving support up and down: push switch up or down. Increasing and decreasing support: push switch forwards or backwards. Adjustable thigh support Pull the lever and slide the thigh support. Overload If the seat setting is electrically overloaded, the power supply is automatically cut-off for a short time. Armrest The armrest can be slid forwards by 10 cm. Under the armrest there is a storage compartment. Armrest storage 3 64.

by pressing the ß button for the respective seat one or more times. The control indicator in the button indicates the setting. Prolonged use of the highest setting for people with sensitive skin is not recommended. Seat heating is operational when engine is running and during an Autostop. Stop-start system 3 164. Rear seats Armrest Fold armrest down. The armrest contains cupholders and a storage box. Seat belts The seat belts are locked during heavy acceleration or deceleration of the vehicle holding the occupants in the sitting position. Therefore the risk of injury is considerably reduced. 9 Warning Fasten seat belt before each trip. In the event of an accident, people not wearing seat belts endanger their fellow occupants and themselves.

only one person at a time. Child restraint system 3 56. Periodically check all parts of the belt system for damage, pollution and proper functionality. Have damaged components replaced. After an accident, have the belts and triggered belt pretensioners replaced by a workshop. 9 Warning The openings in the backrests of the OPC seats are not designed to mount or carry through any kind of additional seat belts. Note Make sure that the belts are not damaged by shoes or sharp-edged objects or trapped. Prevent dirt from getting into the belt retractors. Seat belt reminder Front seats are equipped with a seat belt reminder, indicated for driver seat as control indicator X in the tachometer 3 114 and for passenger seat in the centre console 3 112. Belt force limiters On the front seats, stress on the body is reduced by the gradual release of the belt during a collision. Belt pretensioners In the event of a head-on or rear-end collision of a certain severity, the front seat belts are tightened. 9 Warning Incorrect handling (e.g. removal or fitting of belts) can trigger the belt pretensioners. Deployment of the belt pretensioners is indicated by continuous illumination of control indicator v 3 114. Triggered belt pretensioners must be replaced by a workshop. Belt pretensioners can only be triggered once. Note Do not affix or install accessories or other objects that may interfere with the operation of the belt pretensioners. Do not make any modifications to belt pretensioner components as this will invalidate the vehicle type approval. Three-point seat belt Fastening

guide it untwisted across the body and insert the latch plate into the buckle. Tighten the lap belt regularly whilst driving by pulling the shoulder belt. Loose or bulky clothing prevents the belt from fitting snugly. Do not place objects such as handbags or mobile phones between the belt and your body. 9 Warning The belt must not rest against hard or fragile objects in the pockets of your clothing. Seat belt reminder X 3 114. Height adjustment 1. Pull belt out slightly. 2. Press button. 3. Adjust height and engage. Adjust the height so that the belt lies across the shoulder. It must not lie across the throat or upper arm. Do not adjust while driving.

belt buckle. Seat belts on the rear seats The seat belt for the rear centre seat can only be withdrawn from the retractor if the backrest is engaged in upright position. Using the seat belt while pregnant 9 Warning The lap belt must be positioned as low as possible across the pelvis to prevent pressure on the abdomen. Airbag system The airbag system consists of a number of individual systems depending on the scope of equipment. When triggered the airbags inflate within milliseconds. They also deflate so quickly that it is often unnoticeable during the collision. 9 Warning If handled improperly the airbag systems can be triggered in an explosive manner. Note The airbag systems and belt pretensioner control electronics are located in the centre console area. Do not put any magnetic objects in this area. Do not stick anything on the airbag covers and do not cover them with other materials.

Have deployed airbags replaced by a workshop. Furthermore, it might be necessary to have the steering wheel, the instrument panel, parts of the panelling, the door seals, handles and the seats replaced. Do not make any modifications to the airbag system as this will invalidate the vehicle type approval. When the airbags inflate escaping hot gases may cause burns. Control indicator v for airbag systems 3 114. Front airbag system The front airbag system consists of one airbag in the steering wheel and one in the instrument panel on the front passenger side. These can be identified by the word AIRBAG. Additionally there is a warning label on the side of the instrument panel, visible when the front passenger door is open, or on the front passenger sun visor. The front airbag system is triggered in the event of a front-end impact of a certain severity. The ignition needs to be switched on. The inflated airbags cushion the impact, thereby reducing the risk of injury to the upper body and head of the front seat occupants considerably. 9 Warning Optimum protection is only provided when the seat is in the proper position 3 42. Keep the area in which the airbag inflates clear of obstructions.

engage securely. Only then the airbag is able to protect. Side airbag system The side airbag system consists of an airbag in each front seat backrest. This can be identified by the word AIRBAG. The side airbag system is triggered in the event of a side impact of a certain severity. The ignition must be switched on. The inflated airbags cushion the impact, thereby reducing the risk of injury to the upper body and pelvis in the event of a side-on collision considerably. 9 Warning Keep the area in which the airbag inflates clear of obstructions. Note Only use protective seat covers that have been approved for the vehicle. Be careful not to cover the airbags. Curtain airbag system The curtain airbag system consists of an airbag in the roof frame on each side. This can be identified by the word AIRBAG on the roof pillars. The curtain airbag system is triggered in the event of a side-on impact of a certain severity. The ignition must be switched on. The inflated airbags cushion the impact, thereby reducing the risk of injury to the head in the event of a side-on impact considerably.

inflates clear of obstructions. The hooks on the handles in the roof frame are only suitable for hanging up light articles of clothing, without coat hangers. Do not keep any items in these clothes. Airbag deactivation The front passenger airbag system must be deactivated if a child restraint system is to be fitted on this seat. The side airbag and curtain airbag systems, the belt pretensioners and all driver airbag systems will remain active. The front passenger airbag system can be deactivated via a key- operated switch on the right side of the instrument panel. Use the ignition key to choose the position: *OFF = front passenger airbag is deactivated and will not inflate in the event of a collision. Control indicator *OFF illuminates continuously in the centre console. A child restraint system can be installed in accordance with the chart Child restraint installation locations 3 58. No adult person is allowed to occupy the front passenger seat. VON = front passenger airbag is active. A child restraint system must not be installed.

a child restraint system on a seat with activated front passenger airbag. Risk of fatal injury for an adult person on a seat with deactivated front passenger airbag. If the control indicator V illuminates for approx. 60 seconds after the ignition is switched on, the front passenger airbag system will inflate in the event of a collision. If both control indicators are illuminated at the same time, there is a system failure. The status of the system is not discernible, therefore no person is allowed to occupy the front passenger seat. Contact a workshop immediately. Change status only when the vehicle is stopped with the ignition off. Status remains until the next change. Control indicator for airbag deactivation 3 114. Child restraints Child restraint systems We recommend the Opel child restraint system which is tailored specifically to the vehicle. When a child restraint system is being used, pay attention to the following usage and installation instructions and also those supplied with the child restraint system. Always comply with local or national regulations. In some countries, the use of child restraint systems is forbidden on certain seats. 9 Warning When using a child restraint system on the front passenger seat, the airbag systems for the front passenger seat must be

the airbags poses a risk of fatal injury to the child. This is especially the case if rear- facing child restraint systems are used on the front passenger seat. Airbag deactivation 3 55. Selecting the right system The rear seats are the most convenient location to fasten a child restraint system. Children should travel facing rearwards in the vehicle as long as possible. This makes sure that the child's backbone, which is still very weak, is under less strain in the event of an accident. Suitable are restraint systems that comply with ECE 44-03 or ECE 44-04. Check local laws and regulations for mandatory use of child restraint systems. Ensure that the child restraint system to be installed is compatible with the vehicle type. Ensure that the mounting location of the child restraint system within the vehicle is correct. Allow children to enter and exit the vehicle only on the side facing away from the traffic. When the child restraint system is not in use, secure the seat with a seat belt or remove it from the vehicle. Note Do not stick anything on the child restraint systems and do not cover them with any other materials. A child restraint system which has been subjected to stress in an accident must be replaced.

Permissible options for fitting a child restraint system Weight and age class On front passenger seat On rear outboard seats On rear centre seat activated airbag deactivated airbag Group 0: up to 10 kg or approx. 10 months X U1 U2 U Group 0+: up to 13 kg or approx. 2 years X U1 U2 U Group I: 9 to 18 kg or approx. 8 months to 4 years X U1 U2 U Group II: 15 to 25 kg or approx. 3 to 7 years X X U U Group III: 22 to 36 kg or approx. 6 to 12 years X X U U 1 = Only if front passenger seat airbag system is deactivated. If the child restraint system is being secured using a three- point seat belt, move seat height adjustment to uppermost position and ensure that vehicle safety belt runs forwards from the upper anchorage point. Adjust seat backrest inclination as far as necessary to a vertical position to ensure that the belt is tight on the buckle side. 2 = Seat available with ISOFIX and Top-Tether mounting brackets 3 61. U = Universal suitability in conjunction with three-point seat belt. X = No child restraint system permitted in this weight class.

Weight class Size class Fixture On front passenger seat On rear outboard seats On rear centre seat Group 0: up to 10 kg E ISO/R1 X IL X Group 0+: up to 13 kg E ISO/R1 X IL X D ISO/R2 X IL X C ISO/R3 X IL X Group I: 9 to 18 kg D ISO/R2 X IL X C ISO/R3 X IL X B ISO/F2 X IL, IUF X B1 ISO/F2X X IL, IUF X A ISO/F3 X IL, IUF X IL = Suitable for particular ISOFIX restraint systems of the 'specific-vehicle', 'restricted' or 'semi-universal' categories. The ISOFIX restraint system must be approved for the specific vehicle type. IUF = Suitable for ISOFIX forward-facing child restraint systems of universal category approved for use in this weight class. X = No ISOFIX child restraint system approved in this weight class.

A – ISO/F3 = Forward-facing child restraint system for children of maximum size in the weight class 9 to 18 kg. B – ISO/F2 = Forward-facing child restraint system for smaller children in the weight class 9 to 18 kg. B1 – ISO/F2X = Forward-facing child restraint system for smaller children in the weight class 9 to 18 kg. C – ISO/R3 = Rear-facing child restraint system for children of maximum size in the weight class up to 18 kg. D – ISO/R2 = Rear-facing child restraint system for smaller children in the weight class up to 18 kg. E – ISO/R1 = Rear-facing child restraint system for young children in the weight class up to 13 kg.

systems Fasten vehicle-approved ISOFIX child restraint systems to the ISOFIX mounting brackets. Specific vehicle ISOFIX child restraint system positions are marked in the table by IL. ISOFIX mounting brackets are indicated by a label on the backrest. Top-tether fastening eyes Depending on country specific equipment, the vehicle might have two or three fastening eyes. Top-Tether fastening eyes are marked with the symbol : for a child seat. On Notchback version, open the flap of the required fastening eye on the placement area behind the head restraints, marked by the child seat symbol. On Hatchback and Sports Tourer fastening eyes are on the backside of rear seats. In addition to the ISOFIX mounting, fasten the Top-Tether strap to the Top-Tether fastening eyes. The strap must run between the two guide rods of the head restraint. ISOFIX child restraint systems of universal category positions are marked in the table by IUF.

Load compartment ....................... 84 Roof rack system ......................... 99 Loading information ................... 100 Storage compartments 9 Warning Do not store heavy or sharp objects in the storage compartments. Otherwise, the storage compartment lid could open and vehicle occupants could be injured by objects being thrown around in the event of hard braking, a sudden change in direction or an accident. Glovebox The glovebox features a pen holder, a credit card holder and a coin holder. The glovebox should be closed whilst driving. Cupholders Cupholders are located in the centre console.

cupholders are located under a cover in the centre console. Slide cover backwards. Bottles can be stowed after folding up the intermediate shelf 3 65. Additional cupholders are located in the rear armrest. Fold down the armrest. Front storage A storage compartment is located next to the steering wheel.

drawer. Maximum load: 3 kg. To close, push in and engage. On version with rear carrier system 3 66, the tyre repair kit is stowed in the drawer. Tyre repair kit 3 261. Armrest storage Storage under the front armrest Press button to fold up the armrest. The armrest must be in rearmost position. Storage in the rear armrest Fold down armrest and open cover. Close cover before folding the armrest up.

Front console The storage container can be used to store small items. Depending on the version, a storage compartment is located under a cover. Slide cover backwards. Press button to remove the frame of the cupholder. The frame can be stowed in the glovebox. A further storage compartment is located under the intermediate shelf. Fold up the intermediate shelf and fix it in the vertical position. The frame of the cupholder can be reintegrated to stow bottles. Rear console Pull out the drawer. Caution Do not use for ashes or for other glowing items.

Rear carrier system for two bicycles The rear carrier system (Flex-Fix system) allows bicycles to be attached to a pull-out carrier integrated into the vehicle floor. The transportation of other objects is not permitted. The maximum load of the rear carrier system is 40 kg. The maximum load per bicycle is 20 kg. If not in use, the carrier system must be slid back into the vehicle floor. There must not be any objects on the bicycles that could become loose during transportation. Caution Do not attach bicycles with carbon pedal cranks to bicycle carriers. The bicycles might get damaged. Extending Open the tailgate. 9 Warning No-one should be in the extension zone of the rear carrier system, risk of injury. Pull release lever up. The system disengages and travels quickly out of the bumper.

system until you hear it engage. Ensure that it is not possible to push in the rear carrier system without pulling the release lever again 9 Warning It is only permissible to fit objects to the rear carrier system if the system has been correctly engaged. If the rear carrier system will not engage correctly, do not fit objects to the system and slide the system back. Seek the assistance of a workshop. Install the tail lamps First remove the rear (1), then the front (2) tail lamp from the recesses. Open out the lamp support on the back of the tail lamp completely. Push the clamping lever down and push the lamp support into the retainer until it engages. Perform this procedure for both tail lamps.

make sure these are correctly installed and are securely located. Lock the rear carrier system Swivel the right clamping lever (1) first, followed by the left clamping lever (2), until a resistance is noticeable. The rear carrier system is locked when the clamping levers are swivelled by approx. 50°. Otherwise safe functionality is not guaranteed. Note Close the tailgate.

Fold one or both pedal crank recesses upwards until the diagonal support engages. Remove the pedal crank mounts from the pedal crank recesses. Adapting the rear carrier system to a bicycle Press the release lever and withdraw the wheel recesses.

retainer and remove the strap retainer. Prepare the bicycle for attachment Note The maximum width for the pedal crank is 38.3 mm and the maximum depth is 14.4 mm. Rotate the left pedal (without a chain cog) vertically downwards. The pedal on the left pedal crank must be horizontal. The front bicycle must have its front wheel facing left. The rear bicycle must have its front wheel facing right. Attaching a bicycle to the rear carrier system With the rotary lever on the pedal crank recess, roughly adapt the adjustable pedal crank unit to the protrusion of the pedal crank. If the bicycle has straight pedal cranks, unscrew the pedal crank unit completely (position 5). If the bicycle has curved pedal cranks, screw in the pedal crank unit all the way (position 1).

here must be placed in the pedal crank recess opening as shown in the illustration. Caution Make sure that the pedal does not touch the surface of the rear end carrier. Otherwise the crankset might be damaged during the transport. Insert pedal crank mount into outer rail of each pedal crank recess from above and slide downwards until at least underneath the notching. Attach the pedal crank by rotating the attachment screw on the pedal crank mount. Place the wheel recesses such that the bicycle is more or less horizontal. Here, the distance between the pedals and the tailgate should be at least 5 cm. Both bicycle tyres must be in the wheel recesses. Caution Make sure to pull out the wheel recesses as far as necessary to have both bicycle tyres placed in the recesses. Otherwise a horizontal mounting of the bicycle is not ensured. Disregard could lead to damage of the bicycle wheels caused by hot exhaust fumes.

direction of the vehicle: Slightly loosen the pedal mount. Place the bicycle upright using the rotary lever on the pedal crank recess. If the two bicycles obstruct one another, the relative positions of the bicycles can be adapted by adjusting the wheel recesses and the rotary lever on the pedal crank recess until the bicycles no longer touch one another. Make sure there is sufficient clearance from the vehicle. Tighten the attachment screw for the pedal bearing mount to its maximum point by hand. Secure both bicycle wheels to the wheel recesses using the strap retainers. Check the bicycle to make sure it is secure. Caution Ensure gap between bicycle and vehicle is at least 5 cm. If necessary, loosen handlebar and swivel sideways. The settings for the wheel recesses and on the rotary lever on the pedal crank recess should be noted and saved for each bicycle. Correct presetting will facilitate refitting of the bicycle. It is recommended to attach a warning sign at the rearmost bicycle to increase visibility.

carrier system Undo strap retainers on both bicycle tyres. Hold on to the bicycle, loosen the attachment screw for the pedal bearing mount, then lift the pedal bearing mount to remove it. Retracting the rear carrier system Push the pedal crank mounts into the pedal crank recess like shown in the graphic. Insert the strap retainer and pull tightly downwards as far as possible. Press release lever and slide in wheel recesses all the way as far as they will go.

diagonal support and fold both pedal crank recesses down. 9 Warning Risk of pinching. Swivel first the left clamping lever (1), followed by the right clamping lever (2), until they stop. Push the clamping lever down and pull both lamp supports out of the recesses. Fold in the lamp supports on the backs of the tail lamps. First place the front (1) tail lamp, then the rear (2) tail lamp in the recesses and push down as far as possible. Push cables all the way into all guides in order to prevent damage. Open the tailgate.

Lift the system slightly and push it into the bumper until it engages. Release lever must return to original position. 9 Warning If the system cannot be correctly engaged, please seek the assistance of a workshop. Rear carrier system for four bicycles The rear carrier system (Flex-Fix system) allows two bicycles to be attached to a pull-out carrier integrated into the vehicle floor. It is possible to attach two further bicycles on an adapter. The transportation of other objects is not permitted. The maximum load of the rear carrier system is 80 kg with attached adapter and 60 kg without attached adapter. The maximum load per bicycle on the pull-out carrier is 30 kg. This allows the attachment of electrically- powered bicycles to the pull-out carrier. The maximum load per bicycle on the adapter is 20 kg. If not in use, the carrier system must be slid back into the vehicle floor. There must not be any objects on the bicycles that could become loose during transportation. Caution If the rear carrier system is extended and the vehicle is fully loaded, the chassis clearance will be reduced. Drive carefully whenever the road has a strong inclination or when driving over a ramp, bump, etc. Caution Consult your bicycle dealer before attaching bicycles with carbon frames. The bicycles might get damaged. Extending Open the tailgate.

zone of the rear carrier system, risk of injury. Pull release lever up. The system disengages and travels quickly out of the bumper. Completely pull out the rear carrier system until you hear it engage. Ensure that it is not possible to push in the rear carrier system without pulling the release lever again. 9 Warning It is only permissible to fit objects to the rear carrier system if the system has been correctly engaged. If the rear carrier system will not engage correctly, do not fit objects to the system and slide the system back. Seek the assistance of a workshop. Unfold number plate holder Lift the number plate holder and fold it backwards.

Fold out both tail lamps. Lock the rear carrier system Swivel both clamping levers sidewards as far as they will go. Otherwise safe functionality is not guaranteed. Fold out wheel recesses Fold out both wheel recesses. Assembling the bicycle rack Lift the rack at the rear (1) and pull it backwards. Fold up the rack (2).

handle (2) backwards to engage. Attaching the first bicycle 1. Rotate the pedals into position as shown in the illustration and put the bicycle on the foremost wheel recess. Make sure that the bicycle stands centrally on the wheel recesses. 2. Attach the short mounting bracket to the bicycle frame. Turn the knob clockwise to fasten. 3. Secure both bicycle wheels to the wheel recesses using the strap retainers. 4. Check the bicycle to make sure it is secure. Caution Ensure gap between bicycle and vehicle is at least 5 cm. If necessary, loosen handlebar and swivel sidewards.

When carrying more than two bicycles, the adapter has to be fixed before the second bicycle is attached. 1. Apply the adapter to the rear carrier system as shown in the illustration. 2. Turn the lever (1) forwards and hold, then lower the adapter (2) at the rear. 3. Release lever and check if the adapter is engaged securely. 4. Guide the strap attached to the adapter underneath the lever for folding back the rear carrier system. Fasten the strap. Attaching further bicycles The attachment of further bicycles is similar to the attachment of the first bicycle. Additionally some steps must be considered: 1. Before putting on the bicycle, always unfold the wheel recesses for the next bicycle if necessary. 2. Always rotate the pedals into an appropriate position before putting on the bicycle.

carrier system alternately aligned to the left and to the right. 4. Align the bicycles to the one attached before. The wheel hubs of the bicycles must not touch each other. 5. Attach the bicycles with mounting brackets and strap retainers as described for the first bicycle. The mounting brackets should be fixed in parallel. Use the long mounting bracket to attach the second bicycle to the rack. Use the longer accessory mounting bracket to attach the third bicycle to the rack. Use the short accessory mounting bracket to attach the fourth bicycle. The bracket has to be fixed between the frames of the third and fourth bicycle. 6. Additionally secure both bicycle wheels of the fourth bicycle to the wheel recesses using the tensioning straps.

warning sign at the rearmost bicycle to increase visibility. Fold the rear carrier system backwards The rear carrier system can be folded backwards to get access to the load compartment. ■ Without attached adapter: Push the lever (1) to disengage and hold. Pull the rack (2) backwards to fold the rear carrier system. ■ With attached adapter: 9 Warning Take care when disengaging the rear carrier system as it will tilt backwards. Risk of injury. Hold frame (1) of rearmost bicycle with one hand and pull the loop (2) to disengage. Hold rearmost bicycle with both hands and fold the rear carrier system backwards. To increase visibility, the tail lights of the vehicle are activated when the rear carrier system is folded back. 9 Warning When folding the rear carrier system forwards again, take care that the system is engaged securely. Removing bicycles Undo strap retainers on both bicycle tyres. Turn knob anti-clockwise and remove mounting brackets. Detaching adapter Detach the adapter before removing the last bicycle left on the rear carrier system. 1. Fold in wheel recesses.

3. Turn the lever (1) forwards and hold. 4. Lift the adapter (2) at the rear and remove. Disassembling the bicycle rack Arrange mounting brackets as shown in the illustration. Swivel handle (1) forwards to disengage and lift the rack (2). Fold the rack backwards, then push forwards until it stops (1). Press the rack down at the rear (2). Fold in wheel recesses Fold in both wheel recesses.

Unlock the rear carrier system Swivel both clamping levers inwards as far as they will go. Fold in tail lamps Swivel in both tail lamps. Fold in number plate holder Lift the number plate holder and fold it forwards. Retracting the rear carrier system Caution Take care that all foldable parts, e.g. wheel recesses and mounting brackets, are stowed accurately. Otherwise the rear carrier system might get damaged when trying to retract it. Push the release lever up and hold. Lift the system slightly and push it into the bumper until it engages. Release lever must return to original position. 9 Warning If the system cannot be correctly engaged, please seek the assistance of a workshop.

two parts. Both parts can be folded down. Load compartment extension, 3-door and 5-door hatchback, 4- door notchback ■ Only 3-door and 5-door hatchback: remove the load compartment cover if necessary. ■ Press and hold the catch to push the head restraints down 3 40. ■ Fold up the rear armrest. ■ Guide the seat belts through side supports to protect them against damage. When folding the backrests, pull the seat belts along with them. ■ Pull the release lever on one or both sides and fold down the backrests onto the seat cushion. ■ Take the seat belt out of the seat backrest guide and put it behind the retainer as shown in the illustration. To fold up, raise the backrests and guide them into an upright position until they engage audibly. Ensure that the seat belts of the outboard seats are placed in the corresponding belt guides. The backrests are properly engaged when the red marks on both sides near the release lever are no longer visible. 9 Warning When folding up, ensure that backrests are securely locked in position before driving. Failure to

or damage to load or vehicle in the event of heavy braking or collision. The seat belt of the centre seat could be blocked when the backrest is folded up too quickly. To unlock the retractor, push in the seat belt or pull it out by approx. 20 mm and then let go. Load compartment extension, Sports tourer Folding down rear backrests ■ Remove the load compartment cover if necessary. ■ Press and hold the catch to push the head restraints down 3 40. ■ Fold up the rear armrest. ■ Guide the seat belts through side supports to protect them against damage. When folding the backrests, pull the seat belts along with them. ■ Pull the release lever on one or both sides and fold down the backrests onto the seat cushion. Electrical seat folding On vehicles with electric seat folding, the rear seats can also be folded from the load compartment. ■ Pull switch on left or right sidewall of the load compartment to fold the corresponding part of the rear seat.

electric foldable rear seats. The seat backrest is folded with considerable power. Risk of injury, particularly to children. Ensure that nothing is attached to the rear seats or located on the seat cushion. If the vehicle is to be loaded via a rear door, take the seat belt out of the seat backrest guide and put it behind the retainer as shown in the illustration. ■ To fold up, raise the backrests and guide them into an upright position until they engage audibly. Ensure that the seat belts of the outboard seats are placed in the corresponding belt guides. The backrests are properly engaged when the red marks on both sides near the release lever are no longer visible. 9 Warning Only drive the vehicle if the backrests are securely locked into position. Otherwise there is a risk of personal injury or damage to the load or vehicle in the event of heavy braking or a collision. The seat belt of the centre seat could be blocked when the backrest is folded up too quickly. To unlock the retractor, push in the seat belt or pull it out by approx. 20 mm and then let go.

backrest ■ Pull the strap on one or both seat cushions and lift the rear of the cushion forwards. ■ Press and hold the catch to push the head restraints down 3 40. ■ Pull the release lever on one or both sides of the backrests and fold down onto the seat cushion to get a flat load bay. Remove the seat cushion ■ Push both levers forward and remove seat cushion to extend the loading area. ■ To attach, apply seat cushion as shown in the illustration and engage both levers. Open the pass-through in the rear centre backrest ■ Fold down the rear armrest. ■ Pull the grip and open the cover. Suitable for loading long, narrow objects. Ensure that the cover engages after folding up.

from the side of the load compartment. Turn the knob 90°: knob horizontal = cover secured from the side of the passenger compartment knob vertical = cover not secured Rear storage 3-door hatchback Press both buttons and fold down cover. Maximum load: 0.5 kg. Load compartment cover Do not place any objects on the cover. 3-door and 5-door hatchback Removing Unhook retaining straps from tailgate.

upwards at the front. Remove the cover. If the height adjustable cover is mounted in the middle or upper position, the load compartment cover can be stowed below it. Height adjustable cover 3 90. Fitting Engage cover in side guides and fold downwards. Attach retaining straps to tailgate. Sports tourer Closing cover Pull the cover towards the rear using the handle until it engages in the sideward retainers. Opening cover Pull the handle at the end of the cover to the rear and downwards. It rolls up automatically. Cover in upper position Push the handle at the end of the cover downwards. The rear of the cover is guided upwards automatically.

Pull the release lever on the right side up and hold it. Lift the cover first on the right side and remove from retainers. The removed cover can be stored under the rear floor cover like shown in the graphic. Rear floor storage cover 3 90. Installing cover Insert the left side of the load compartment cover in the recess, pull the release lever up and hold it, insert the right side of the load compartment cover and engage. Rear floor storage cover Rear floor cover, 3-door hatchback, 5-door hatchback The rear floor cover can be lifted. Hinge the loop into the hook on the lower side of the load compartment cover. Caution Only use the hook for hanging up the rear floor cover and the height adjustable cover.

hatchback, 5-door hatchback The height adjustable cover can be mounted in three positions: ■ directly above the rear floor cover (1), ■ in a middle position (2) ■ in an upper position (3). Caution Ensure that the front and rear end of the height adjustable cover are attached to the same level. Lifting To lift the cover to a higher level, pull the loop backwards and lift the rear edge of the cover onto the corresponding supports. Lowering To lower the cover, pull the strap backwards and push down the front centre of the cover at the same time. Caution Do not lower the height adjustable cover to position 1 in vehicles equipped with subwoofer. The subwoofer could be damaged.

space between the rear floor cover and the height adjustable cover can be used as a stowage compartment. ■ The height adjustable cover can be lifted and hooked in with the strap when it is mounted in position 1 or 2. ■ If mounted in position 2, an almost completely flat load bay is created if the rear seat backrests are folded forwards. ■ Opening the side covers (e.g. when exchanging the rear light bulbs) is only possible with the height adjustable cover mounted in position 1 or 2. Caution The height adjustable cover is able to withstand a load of no more than 100 kg. Rear floor cover, Sports tourer Lift the rear floor cover by pulling the handle. Fold and place the cover behind the rear seats. The storage compartment below the rear floor cover can be divided by a bar. Insert the bar into the recesses at the sidewalls. Caution Insert the bar into the rearmost recess when transporting heavy objects in the load compartment. Otherwise the rear floor cover might be damaged.

secure items against slippage, e.g. using lashing straps or luggage net. Cargo management system The FlexOrganizer is a flexible system for dividing up the load compartment. The system consists of: ■ adapters, ■ mesh pockets, ■ hooks, ■ service box, ■ strap set. The components are fitted in rails on both side panels using adapters and hooks. Installation of adapters in the rails Fold open the handle plate, insert the adapter into the upper and lower groove of the rail and move to the required position. Turn the handle plate upwards to lock the adapter. To remove, turn the handle plate down and move out of the rail. Variable partition net Insert adapters into the required position in the rails. Stick together the halves of the net rods. To install, push rods together a little and insert into the relevant openings in the adapters. To remove, press the net rods together and remove from the adapters.

position in the rails. The net pocket can be suspended from the adapters. Installation of hooks in the rails Insert the hook in the desired position first in the upper groove of the rail and then press in the lower groove. To remove, first pull out of the upper groove. Service box Install two hooks in the upper rail. Insert the upper brackets of the box from above into the hooks.

lower rail. Plug in the lower brackets of the box from above into the lower hooks. Strap set Insert the adapters of the strap set in a rail. Make sure that the belt is not twisted. The strap set has two locks to open. The belt can be tightened. Safety net The safety net is available on the Sports tourer and can be installed behind the rear seats or, if the rear seat backrests are folded and the seat cushions raised, behind the front seats. Passengers must not be transported behind the safety net. Installation Behind the rear seats Attach lower hook with opening facing backward to eye in the right and left of the floor. Adjust strap length on safety net by attaching the upper hook to the eyes of the strap. Keep strap under tension while proceeding with installation of rod.

Attach strap to eyes underneath the rear seat cushion. Fold backrests forward. To get a flat load bay, first fold seat cushion before attaching the safety net. Move front seats forward to ease tension if necessary. Installation of the rod There are two installation openings in the roof frame: suspend and engage rod of net at one side, compress rod and suspend and engage at other side. Load compartment 3 84. Removal Unhook the safety net rods from the brackets in the roof frame. Detach straps from the eyes. Roll up the net and secure with a strap. The removed safety net can be stored under the rear floor cover 3 90. Warning triangle 3-door hatchback, 5-door hatchback Stow the warning triangle in the space behind the strap on the right side of the load compartment.

triangle in the space behind the straps on the inside of the tailgate. 4-door notchback Stow the warning triangle in the recess on the left side of the load compartment. First aid kit 5-door hatchback Stow the first aid kit in the stowage compartment behind the warning triangle. Before first use, press in the interior trim at the top and at the sides of the perforation. Then fold the trim outward to gain access to the stowage compartment.

compartment behind the warning triangle. Use the recesses to fold down the cover. Depending on the equipment, the first aid kit can be stored in the rear storage 3 88. Sports tourer Fold down strap. Stow the first aid kit in the space behind a strap on the inside of the tailgate. 4-door notchback Stow the first aid kit in the space behind the mesh net on the right side of the load compartment.