Hatco GR3-27 Installation And Operating Manual

GR3 & GR3L Series Installation & Operating Manual I&W #07.05.175.00 This manual contains important safety information concerning the maintenance, use and operation of this product. Failure to follow the instructions contained in this manual may result in serious injury. If you’re unable to understand the contents of this manual, please bring it to the attention of your supervisor. Do not operate this equipment unless you have read and understood the contents of this manual. Este manual contiene importante información sobre seguridad concerniente al mantenimiento, uso y operación de este producto. Cualquier falla en el seguimiento de las instrucciones contenidas en este manual puede resultar en un serio daño. Si usted no puede entender el contenido de este manual por favor pregunte a su supervisor. No opere este equipo al menos que haya leído y comprendido el contenido de este manual.

i CONTENTS INTRODUCTION Hatco Glo-Ray Heated Glass Overshelves are perfect for keeping prepared foods hot at kitchen work areas, waitress pickup stations, buffet lines or other customer serving points. The Glo-Ray Heated Glass Overshelf features a unique patented glass shelf that keeps food below the glass at optimum serving temperatures while maintaining product quality. Additionally, the top of the heated glass overshelf is ideal for holding wrapped or boxed food short term when serving temperatures are not critical. This manual provides the installation, safety and operating instructions for the Glo-Ray Heated Glass Overshelves. We recommend all installation, operating and safety information appearing in this manual be read prior to installation or operation of your Hatco Heated Glass Overshelf. Safety information that appear in this manual after a warning symbol and the words WARNING or CAUTION printed in bold face are very important. WARNING means there is the possibility of serious personal injury or death to yourself or others. CAUTION means there is the possibility of minor or moderate injury. NOTICE signifies the possibility of equipment or property damage only. Hatco Glo-Ray Heated Glass Overshelves are a product of extensive research and field testing. The materials used were selected for maximum durability, attractive appearance and optimum performance. Every unit is thoroughly inspected and tested prior to shipment. Important Owner Information...............................i Introduction ...........................................................i Important Safety Information..............................1 Model Description................................................3 All Models........................................................3 GR3 Models ....................................................3 GR3L Models ..................................................3 Model Designation ...............................................3 Specifications.......................................................4 Electrical Requirements ..................................4 Electrical Rating Charts...................................4 Dimensions ....................................................4 Installation ............................................................5 Unpacking .......................................................5 Location...........................................................5 Mounting the Unit............................................6 Operation ..............................................................8 Ground Fault Circuit Interrupt .........................8 Maintenance .........................................................9 Cleaning ..........................................................9 Display Light Bulb Replacement.....................9 Accessories........................................................10 Hatco Limited Warranty.....................................11 Authorized Parts Distributors ............Back Cover IMPORTANT OWNER INFORMATION Record the model number, serial number (identification decal located on the inside of the control box), voltage and purchase date of your Glo- Ray® Heated Glass Overshelf in the spaces below. Please have this information available when contacting Hatco for service assistance. Model No. ________________________________ Serial No. ________________________________ Voltage __________________________________ Date of Purchase __________________________ Business 8:00 a.m. to 5:00 p.m. Hours: Central Standard Time (Summer Hours: June to September – 8:00 a.m. to 5:00 p.m. C.S.T. Monday through Thursday 8:00 a.m. to 2:30 p.m. C.S.T. Friday) Telephone: (800) 558-0607; (414) 671-6350 Fax: (800) 690-2966 (Parts & Service) (414) 671-3976 (International) Additional information can be found by visiting our web site at www.hatcocorp.com 24-Hour 7-Day Parts & Service Assistance available in the United States and Canada by calling (800) 558-0607.

1 IMPORTANT SAFETY INFORMATION This product has no “user” serviceable parts. To avoid damage to the unit or injury to personnel, use only Authorized Hatco Service Agents and Genuine Hatco Replacement Parts when service is required. If service is required on this unit, contact your Authorized Hatco Service Agent, or contact the Hatco Service Department at 800-558- 0607 or 414-671-6350; fax 800-690-2966 or International fax 414-671-3976. Genuine Hatco Replacement Parts are specified to operate safely in the environments in which they are used. Some aftermarket or generic replacement parts do not have the characteristics that will allow them to operate safely in Hatco equipment. It is essential to use Hatco Replacement Parts when repairing Hatco equipment. Failure to use Hatco Replacement Parts may subject operators of the equipment to hazardous electrical voltage, resulting in electrical shock or burn. CAUTIONS To avoid any injury or damage locate the unit at the proper counter height, in an area that is convenient for use. The location should be level to prevent the unit or its contents from accidentally falling, and strong enough to support the weight of the unit and food displayed. Unit is not weatherproof. For safe and proper operation locate the unit indoors where the ambient air temperature is constant and is a minimum of 70°F (21°C). To avoid any injury or burns, do not come in contact with the Heated Glass Overshelf while unit is in operation. All electrical connections must be in accordance with local electrical codes and any other applicable codes. Connections should be made by a qualified, licensed electrician. WARNINGS To avoid any injury, turn the power switch OFF, and allow to cool completely before performing any cleaning or maintenance. To avoid any injury, do not allow liquids to spill onto the Heated Glass Overshelf. Some exterior surfaces on the unit will get hot. Use caution when touching these areas to avoid injury. To avoid any injury, do not clean Heated Glass Overshelf when unit is energized or hot. Unit is not waterproof. To avoid electrical shock or personal injury DO NOT submerge in water. Do not operate if it has been submerged in water. To avoid electrical shock or personal injury, do not steam clean or use excessive water on the unit. For safe and proper operation, the unit must be located a reasonable distance from combustible walls and materials. If safe distances are not maintained, discoloration or combustion could occur. For safe and proper operation do not place food product directly onto glass surface. Food product must be wrapped or boxed. For safe and proper operation, the top side of the shelf is intended for short term holding of food for which serving temperature is not critical. The fluorescent light fixtures used have plastic safety shields covering the fluorescent bulbs to meet N.S.F. standards. To avoid personal injury and/or food contamination always operate the unit with the plastic safety shield properly installed. After installing a fluorescent light bulb make sure to reinstall the protective lens cover. Breakage of a bulb not properly covered could result in personal injury and/or food contamination. IMPORTANT! Read the following important safety information to avoid personal injury or death, and to avoid damage to the equipment or property.

2 IMPORTANT SAFETY INFORMATION NOTICES Use only non-abrasive cleaners. Abrasive cleaners could scratch the finish marring its appearance and making it susceptible to dirt accumulation. Only soft cleaning cloths, mild soap and water should be used to clean breath protector(s). Breath protector(s) are made of shatterproof polycarbonate and will scratch or crack if proper care is not taken. Do not allow the glass shelf to overheat. Overheating may cause the food containers to melt or soften. Use of excessive force when tightening mounting screws may damage unit or countertop. Do not use food pans, ceramic dishes, or abrasive materials on Heated Glass Overshelves. Food pans, ceramic dishes, and abrasive materials may scratch the glass shelf marring its appearance and making it susceptible to dirt accumulation. It is recommended that glass overshelves be used for food products contained in disposable paper or plastic containers or wrapping. IMPORTANT! Read the following important safety information to avoid personal injury or death, and to avoid damage to the equipment or property. Damage to countertop material such as Corian® and similar products caused by heat generated from Hatco equipment is not covered under the Hatco warranty. Recommended for use over metallic counters. For other surfaces, verify that the material is suitable for temperature up to 180°F (82°C). The Remote Mounted Control Box must be installed outside of the heat zone. Locating the control box inside the heat zone will cause the switches to overheat, malfunction, and fail. See Figure 6 for minimum mounting distances.

3 MODEL DESCRIPTION MODEL DESIGNATION ALL MODELS All models are ideal for pass-through areas, buffet and cafeteria lines and other self-serving areas. All models are available as either standard or high wattage units. Standard wattage units may be used where there is an additional bottom source of heat, such as the Hatco Heated Base Overshelves GRS, GRSB, GRSBF, and GRSR. High wattage units are for use in installations where no bottom heat source is present. Units are available in widths of 29" (737 mm), 35" (889 mm) and 41" (1041 mm). Options available for these units include front and rear breath protectors and a choice of either a Designer color or stainless steel finish. The remote- mounted control box includes a 3' (914 mm) flexible electrical conduit. GR3 MODELS The GR3 Heated Glass Overshelf is constructed of stainless steel or powdercoat painted steel in Designer colors and glass. Featuring a remote mounted On/Off toggle switch, Ground Fault Circuit Interrupt (GFCI) safety, indicator light and one adjustable infinite heat control for the heated glass overshelf. Figure 1. Glo-Ray® Model GR3-35 with Optional Breath Protectors GR 3 H L - 29 Overall Width Fluorescent Light High Wattage Heated Glass Glo-Ray No Character - Standard Wattage Figure 2. Model Designation GR3L MODELS The GR3L Heated Glass Overshelf is constructed of stainless steel or powdercoat painted steel in Designer colors and glass. Featuring a remote mounted On/Off toggle switch, a Ground Fault Circuit Interrupt (GFCI) safety, indicator light, one adjustable infinite heat control for the heated glass overshelf, and two fluorescent lights to illuminate the warming area.

4 SPECIFICATIONS ELECTRICAL REQUIREMENTS Units are supplied from the factory equipped with a 3' (914 mm) flexible electrical conduit connection to the remote control box. Figure 3. Dimensions CAUTION All electrical connections must be in accordance with local electrical codes and any other applicable codes. Connections should be made by a qualified, licensed electrician. Model Voltage Watts Amps Electrical Connection Shipping Weight GR3-29 120 758 6.3 Conduit 59 lbs. (27 kg) GR3H-29 120 1263 10.5 Conduit 59 lbs. (27 kg) GR3-35 120 941 7.8 Conduit 71 lbs. (32 kg) GR3H-35 120 1600 13.3 Conduit 71 lbs. (32 kg) GR3-41 120 1143 9.5 Conduit 83 lbs. (38 kg) GR3H-41 120 1895 15.8 Conduit 83 lbs. (38 kg) ELECTRICAL RATING CHART – GR3 MODELS Model Voltage Watts Amps Electrical Connection Shipping Weight GR3L-29 120 794 6.6 Conduit 61 lbs. (27 kg) GR3HL-29 120 1299 10.8 Conduit 61 lbs. (27 kg) GR3L-35 120 977 8.1 Conduit 73 lbs. (33 kg) GR3HL-35 120 1636 13.6 Conduit 73 lbs. (33 kg) GR3L-41 120 1179 9.8 Conduit 85 lbs. (38 kg) GR3HL-41 120 1931 16.1 Conduit 85 lbs. (38 kg) ELECTRICAL RATING CHART – GR3L MODELS DIMENSIONS Width Depth† Height Interior Interior Interior Model (A) (B) (C) (D) (E) (F) GR3-29 & 29" 27-3/16" 13-1/2" 25-11/16" 10-3/16" 9" GR3H-29 (737 mm) (691 mm) (343 mm) (652 mm) (259 mm) (229 mm) GR3-35 & 35" 27-3/16" 13-1/2" 31-11/16" 10-3/16" 9" GR3H-35 (889 mm) (691 mm) (343 mm) (805 mm) (259 mm) (229 mm) GR3-41 & 41" 27-3/16" 13-1/2" 37-11/16" 10-3/16" 9" GR3H-41 (1041 mm) (691 mm) (343 mm) (957 mm) (259 mm) (229 mm) Width Depth† Height Interior Interior Interior Model (A) (B) (C) (D) (E) (F) GR3L-29 & 29" 27-3/16" 13-1/2" 25-11/16" 10-3/16" 9" GR3HL-29 (737 mm) (691 mm) (343 mm) (652 mm) (259 mm) (229 mm) GR3L-35 & 35" 27-3/16" 13-1/2" 31-11/16" 10-3/16" 9" GR3HL-35 (889 mm) (691 mm) (343 mm) (805 mm) (259 mm) (229 mm) GR3L-41 & 41" 27-3/16" 13-1/2" 37-11/16" 10-3/16" 9" GR3HL-41 (1041 mm) (691 mm) (343 mm) (957 mm) (259 mm) (229 mm) A C Note: Shipping weight includes packaging. B D E F † 37-1/4" (946 mm) including accessory breath protectors. Usable Heated Top Shelf Area: GR3-, GR3L-, GR3H-, GR3HL-29: 23-1/4"W x 21-1/4"D (591 x 540 mm) GR3-, GR3L-, GR3H-, GR3HL-35: 29-1/4"W x 21-1/4"D (743 x 540 mm) GR3-, GR3L-, GR3H-, GR3HL-41: 35-1/4"W x 21-1/4"D (895 x 540 mm)

5 INSTALLATION UNPACKING Glo-Ray® Heated Glass Overshelves are shipped with most components pre-assembled. Care should be taken when unpacking shipping carton to avoid damage to unit and components enclosed. 1. Remove unit from box. 2. Remove information packet. To prevent delay in obtaining warranty coverage, fill out and mail in the warranty card. 3. Remove tape and protective packaging from all surfaces of unit. LOCATION For proper operation and maximum performance, locate the Heated Glass Overshelf in an area where the ambient air temperature is constant and is a minimum of 70°F (21°C). Areas which are susceptible to active air movements or currents should be avoided, i.e., near exhaust fans or hoods and air conditioning ducts. CAUTION Unit is not weatherproof. For safe and proper operation locate the unit indoors where the ambient air temperature is constant and is a minimum of 70°F (21°C). WARNING For safe and proper operation, the unit must be located a reasonable distance from combustible walls and materials. If safe distances are not maintained, discoloration or combustion could occur. CAUTION To avoid any injury or damage locate the unit at the proper counter height, in an area that is convenient for use. The location should be level to prevent the unit or its contents from accidentally falling, and strong enough to support the weight of the unit and food displayed. CAUTION All electrical connections must be in accordance with local electrical codes and any other applicable codes. Connections should be made by a qualified, licensed electrician. NOTICE Damage to countertop material such as Corian® and similar products caused by heat generated from Hatco equipment is not covered under the Hatco warranty. Recommended for use over metallic counters. For other surfaces, verify that the material is suitable for temperature up to 180°F (82°C).

6 INSTALLATION MOUNTING THE UNIT (See Figure 4) NOTE: Locate the conduit hole 15-5/8" (397 mm) away from the front edge (not including breath protector) of the unit overhang on the top shelf or 2" (51 mm) away from center of mounting bracket or unit, front to back, and 7/8" (22 mm) in from the side of the unit. 1. Drill a 1-3/8" (35 mm) hole in countertop for the wire routing. 2. Route flexible conduit through the pre-drilled hole and place unit on countertop. 3. Remove the screw from each counter mount cover and lift cover to expose mounting holes. 4. Using the mounting brackets as a template, mark the mounting holes in the countertop. NOTE: Verify legs on unit are straight and perpendicular before marking and drilling holes. 5. Move the unit out of the way and drill 8 mounting holes (4 for each side). Drill appropriate sized holes based on fastener size (fasteners not supplied). 6. Position unit on countertop. 7. Secure the unit to the countertop (hardware not supplied). NOTE: If mounting to a wooden countertop, use #10 wood screw (length will depend on countertop thickness). For other countertop materials, drill holes through countertop and Figure 4. Mounting the Unit Mounting Bracket Screw (Not Supplied) Nut (Not Supplied) Front Edge Of Unit Center Line Of Unit Left Edge Of Unit Flexible Conduit Counter Mount Cover secure with bolts and nuts. Units mounted to a metal surface may require a backing plate installed to the underside of the surface in order to increase unit stability (backing plate not supplied). 8. Secure counter mount covers in place using original hardware. Do not overtighten. NOTICE Use of excessive force when tightening mounting screws may damage unit or countertop. NOTE: Hatco recommends a qualified electrician connect the appropriate electrical power source to the Remote Control Box. Refer to SPECIFICATIONS, WIRING DIAGRAM, or the unit identification plate for specific model watt and amp ratings. 9. Connect incoming power supply to the wire leads inside the Remote Control Box. Wire leads are factory attached to the Ground Fault Circuit Interrupt (GFCI) switch. 10.Route wires located in the Flexible Conduit through knock outs located on either end of the Remote Control Box. 11.Secure Flexible Conduit to the Remote Control Box. 12.Connect heating unit and lights by attaching the Flexible Conduit wires to the terminal block located inside the Remote Control Box. (See WIRING DIAGRAM for details.) 15-5/8" (397 mm) 2" (51 mm) 7/8" (22 mm) Conduit Hole Top View

7 INSTALLATION Figure 5. Remote Mounted Control Box Figure 6. Minimum Remote Mounting Distance for Remote Control Box REMOTE MOUNTED CONTROL BOX (RMB) Remote mounted control box should be installed by a qualified electrician. NOTE: When mounting the remote mounted control box insure space is available to access the GFCI reset button. NOTICE The Remote Mounted Control Box must be installed outside of the heat zone. Locating the control box inside the heat zone will cause the switches to overheat, malfunction, and fail. See Figure 6 for minimum mounting distances.

8 OPERATION WARNING To avoid any injury, do not allow liquids to spill onto the Heated Glass Overshelf. WARNING Unit is not waterproof. To avoid electrical shock or personal injury DO NOT submerge in water. Do not operate if it has been submerged in water. WARNING For safe and proper operation do not place food product directly onto glass surface. Food product must be wrapped or boxed. WARNING Some exterior surfaces on the unit will get hot. Use caution when touching these areas to avoid injury. CAUTION To avoid any injury or burns, do not come in contact with the Heated Glass Overshelf while unit is in operation. The Heated Glass Overshelves main power is controlled by an ON/OFF toggle switch. (See Figure 7.) The switch must be in the ON position for the unit to function. On the GR3L models the fluorescent display lights are also controlled by the ON/OFF toggle switch. The Heated Glass Overshelf is controlled by the infinite heat control switch and can be set to any desired heating level as indicated on the control plate. (See Figure 7.) The indicator light indicates that the heated glass shelf is on. The Heated Glass Overshelf provides a dual heat source radiating heat downward to blanket the product below, and conducting heat upward to keep packaged food on the glass shelf warm. The top side of the Heated Glass Overshelf, with the infinite heat control switch set on high, reaches 180°F (82°C). Allow 30 minutes for unit to reach operating temperature. NOTE: To operate the unit for display only with no heat (GR3L Series only), position the heat control to the lowest or OFF setting. NOTICE Do not allow the glass shelf to overheat. Overheating may cause the food containers to melt or soften. Figure 7. Control Panel WARNING For safe and proper operation, the top side of the shelf is intended for short term holding of food for which serving temperature is not critical. NOTICE Do not use food pans, ceramic dishes, or abrasive materials on Heated Glass Overshelves. Food pans, ceramic dishes, and abrasive materials may scratch the glass shelf marring its appearance and making it susceptible to dirt accumulation. It is recommended that glass overshelves be used for food products contained in disposable paper or plastic containers or wrapping. GROUND FAULT CIRCUIT INTERRUPT Units are supplied with a built in Ground Fault Circuit Interrupt (GFCI) which is designed to turn electrical power off to the internal components when there is a short circuit or electrical fault. (See Figure 7.) To reset the “GFCI” push the reset button in. If the “GFCI” continues to trip, contact your local Authorized Hatco Service Agency. Indicator Light ON/OFF Switch Ground Fault Circuit Interrupt (GFCI) Switch Infinite Heat Control Switch

9 MAINTENANCE CLEANING Hatco Glo-Ray® Heated Glass Overshelves are designed for maximum durability and performance, with minimum maintenance. WARNING To avoid any injury, turn the power switch OFF, and allow to cool completely before performing any cleaning or maintenance. WARNING To avoid any injury, do not allow liquids to spill onto the Heated Glass Overshelf. WARNING To avoid electrical shock or personal injury, do not steam clean or use excessive water on the unit. NOTICE Use only non-abrasive cleaners. Abrasive cleaners could scratch the finish marring its appearance and making it susceptible to dirt accumulation. NOTICE Only soft cleaning cloths, mild soap and water should be used to clean breath protector(s). Breath protector(s) are made of shatterproof polycarbonate and will scratch or crack if proper care is not taken. WARNING To avoid any injury, do not clean Heated Glass Overshelf when unit is energized or hot. The Heated Glass Overshelf should be cleaned daily with ordinary glass cleaner and soft cloth or paper towel. DISPLAY LIGHT BULB REPLACEMENT- GR3L MODELS ONLY GR3L units are equipped with two 120 volt fluorescent light tubes which illuminate the warming area. These tubes have a special lens cover to guard against injury and food contamination in the event of breakage. To replace a fluorescent light, turn the power switch off and wait until the unit has cooled. Remove the protective lens cover from the fixture and carefully twist the fluorescent tube and pull to remove it from the sockets. Reverse procedure to re-assemble. WARNING After installing a fluorescent light bulb make sure to reinstall the protective lens cover. Breakage of a bulb not properly covered could result in personal injury and/or food contamination. WARNING The fluorescent light fixtures used have plastic safety shields covering the fluorescent bulbs to meet N.S.F. standards. To avoid personal injury and/or food contamination always operate the unit with the plastic safety shield properly installed. WARNING If service is required on this unit, contact your Authorized Hatco Service Agent, or contact the Hatco Service Department at 800-558-0607 or 414-671-6350; fax 800-690-2966 or International fax 414-671-3976. WARNING This product has no “user” serviceable parts. To avoid damage to the unit or injury to personnel, use only Authorized Hatco Service Agents and Genuine Hatco Replacement Parts when service is required. WARNING Genuine Hatco Replacement Parts are specified to operate safely in the environments in which they are used. Some aftermarket or generic replacement parts do not have the characteristics that will allow them to operate safely in Hatco equipment. It is essential to use Hatco Replacement Parts when repairing Hatco equipment. Failure to use Hatco Replacement Parts may subject operators of the equipment to hazardous electrical voltage, resulting in electrical shock or burn.

10 ACCESSORIES BREATH PROTECTOR(S) Accessory breath protector(s) are available from the factory. Refer to Figure 8 and follow these steps to install them. 1. Remove protective paper from acrylic surfaces. 2. Loosen 3 screws from underside of shelf. Slide mounting bracket into position with studs facing to the front and down. Tighten 3 screws. Figure 8. Installing Accessory Breath Protectors 3. Align breath protector mounting holes with studs and secure using acorn nuts provided. Do not overtighten. Stud Breath Protector Mounting Bracket Acorn Nut

11 HATCO LIMITED WARRANTY 1. PRODUCT WARRANTY Hatco warrants the products that it manufactures (the “Products”) to be free from defects in materials and workmanship, under normal use and service, for a period of one (1) year from the date of purchase when installed and maintained in accordance with Hatco’s written instructions or 18 months from the date of shipment from Hatco. Buyer must establish the product’s purchase date by returning Hatco’s Warranty Registration Card or by other means satisfactory to Hatco in its sole discretion. Hatco warrants the following Product components to be free from defects in materials and workmanship from the date of purchase (subject to the foregoing conditions) for the period(s) of time and on the conditions listed below: a) One (1) Year Parts and Labor PLUS One (1) Additional Year Parts-Only Warranty: Toaster Elements (metal sheathed) Drawer Warmer Elements (metal sheathed) Drawer Warmer Drawer Rollers and Slides Food Warmer Elements (metal sheathed) Display Warmer Elements (metal sheathed air heating) Holding Cabinet Elements (metal sheathed air heating) Built-In Heated Well Elements (metal sheathed) b) One (1) Year Parts and Labor PLUS Four (4) Years Parts-Only Warranty on pro-rated terms that Hatco will explain at Buyer’s request: 3CS and FR Tanks c) One (1) Year Parts and Labor PLUS Nine (9) Years Parts-Only Warranty on: Electric Booster Heater Tanks Gas Booster Heater Tanks THE FOREGOING WARRANTIES ARE EXCLUSIVE AND IN LIEU OF ANY OTHER WARRANTY, EXPRESSED OR IMPLIED, INCLUDING BUT NOT LIMITED TO ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE OR PATENT OR OTHER INTELLECTUAL PROPERTY RIGHT INFRINGEMENT. Without limiting the generality of the foregoing, SUCH WARRANTIES DO NOT COVER: Coated incandescent light bulbs, fluorescent lights, lamp warmer heat bulbs, glass components, Product failure in booster tank, fin tube heat exchanger, or other water heating equipment, caused by liming, sediment buildup, chemical attack or freezing, Product misuse, tampering or misapplication, improper installation or application of improper voltage. 2. LIMITATION OF REMEDIES AND DAMAGES Hatco’s liability and Buyer’s exclusive remedy hereunder will be limited solely, at Hatco’s option, to repair or replacement by a Hatco-authorized service agency (other than where Buyer is located outside of the United States, Canada, United Kingdom or Australia in which case Hatco’s liability and Buyer’s exclusive remedy hereunder will be limited solely to replacement of part under warranty) with respect to any claim made within the applicable warranty period referred to above. Hatco reserves the right to accept or reject any such claim in whole or in part. Hatco will not accept the return of any Product without prior written approval from Hatco, and all such approved returns shall be made at Buyer’s sole expense. HATCO WILL NOT BE LIABLE, UNDER ANY CIRCUMSTANCES, FOR CONSEQUENTIAL OR INCIDENTAL DAMAGES, INCLUDING BUT NOT LIMITED TO LABOR COSTS OR LOST PROFITS RESULTING FROM THE USE OF OR INABILITY TO USE THE PRODUCTS OR FROM THE PRODUCTS BEING INCORPORATED IN OR BECOMING A COMPONENT OF ANY OTHER PRODUCT OR GOODS.

(800) 558-0607 (414) 671-6350 Parts & Service Fax (800) 690-2966 Int’l. Fax (414) 671-3976 www.hatcocorp.com HATCO AUTHORIZED PARTS DISTRIBUTORS Printed in U.S.A. August 2007 ALABAMA Jones McLeod Appl. Svc. Birmingham 205-251-0159 ARIZONA Auth. Comm. Food Equip. Phoenix 602-234-2443 Byassee Equipment Co. Phoenix 602-252-0402 CALIFORNIA Industrial Electric Commercial Parts & Service, Inc. Huntington Beach 714-379-7100 Chapman Appl. Service San Diego 619-298-7106 P & D Appliance Commercial Parts & Service, Inc. S. San Francisco 650-635-1900 COLORADO Hawkins Commercial Appliance Englewood 303-781-5548 FLORIDA Whaley Foodservice Repair Jacksonville 904-725-7800 Nass Service Co., Inc. Orlando 407-425-2681 B.G.S.I. Pompano Beach 954-971-0456 Comm. Appliance Service Tampa 813-663-0313 GEORGIA TWC Services Smyrna 770-438-9797 Heritage Service Group Norcross 866-388-9837 Southeastern Rest. Svc. Norcross 770-446-6177 HAWAII Burney’s Comm. Service, Inc. Honolulu 808-848-1466 Food Equip Parts & Service Honolulu 808-847-4871 ILLINOIS Parts Town Lombard 708-865-7278 Eichenauer Elec. Service Decatur 217-429-4229 Midwest Elec. Appl. Service Elmhurst 630-279-8000 Cone’s Repair Service Moline 309-797-5323 INDIANA GCS Service Indianapolis 317-545-9655 IOWA Electric Motor Service Co. Davenport 319-323-1823 Goodwin Tucker Group Des Moines 515-262-9308 KENTUCKY Certified Service Center Lexington 859-254-8854 Certified Service Center Louisville 502-964-7007 LOUISIANA Chandlers Parts & Service Baton Rouge 225-272-6620 MARYLAND Electric Motor Service Baltimore 410-467-8080 GCS Service Silver Spring 301-585-7550 MASSACHUSETTS Ace Service Co., Inc. Needham 781-449-4220 MICHIGAN Commercial Kitchen Service Bay City 517-893-4561 Bildons Appliance Service Detroit 248-478-3320 Midwest Food Equip. Service Grandville 616-261-2000 MINNESOTA GCS Service Minneapolis 612-546-4221 MISSOURI General Parts Kansas City 816-421-5400 Commercial Kitchen Services St. Louis 314-890-0700 Kaemmerlen Parts & Service St. Louis 314-535-2222 NEBRASKA Anderson Electric Omaha 402-341-1414 NEVADA Burney’s Commercial Las Vegas 702-736-0006 Hi. Tech Commercial Service N. Las Vegas 702-649-4616 NEW JERSEY Jay Hill Repair Fairfield 973-575-9145 Service Plus Flanders 973-691-6300 NEW YORK Acme American Repairs, Inc. Brooklyn 718-456-6544 Alpro Service Co. Brooklyn 718-386-2515 Appliance Installation Buffalo 716-884-7425 Northern Parts Dist. Plattsburgh 518-563-3200 J.B. Brady, Inc. Syracuse 315-422-9271 NORTH CAROLINA Authorized Appliance Charlotte 704-377-4501 OHIO Akron/Canton Comm. Svc. Inc. Akron 330-753-6635 Certified Service Center Cincinnati 513-772-6600 Commercial Parts and Service Columbus 614-221-0057 Electrical Appl. Repair Service Independence 216-459-8700 E. A. Wichman Co. Toledo 419-385-9121 OKLAHOMA Hagar Rest. Service, Inc. Oklahoma City 405-235-2184 Krueger, Inc. Oklahoma City 405-528-8883 OREGON Ron’s Service, Inc. Portland 503-624-0890 PENNSYLVANIA Elmer Schultz Services Philadelphia 215-627-5401 FAST Comm. Appl. Service Philadelphia 215-288-4800 Appliance Installation & Service Pittsburgh 412-809-0244 K & D Service Co. Harrisburg 717-236-9039 Electric Repair Co. Reading 610-376-5444 RHODE ISLAND Marshall Electric Co. Providence 401-331-1163 SOUTH CAROLINA Whaley Foodservice Repair W. Columbia 803-791-4420 TENNESSEE Camp Electric Memphis 901-527-7543 TEXAS GCS Service Fort Worth 817-831-0381 Armstrong Repair Service Houston 713-666-7100 Commercial Kitchen Repair Co. San Antonio 210-735-2811 UTAH La Monica’s Rest. Equip. Service Murray 801-263-3221 VIRGINIA Daubers Norfolk 757-855-4097 Daubers Springfield 703-866-3600 WASHINGTON Restaurant Appl. Service Seattle 206-524-8200 WISCONSIN A.S.C., Inc. Madison 608-246-3160 A.S.C., Inc. Milwaukee 414-543-6460 CANADA ALBERTA Key Food Equipment Service Edmonton 780-438-1690 BRITISH COLUMBIA Key Food Equipment Service Vancouver 604-433-4484 MANITOBA Air Rite, Inc. Winnepeg 204-895-2300 NEW BRUNSWICK EMR Services, Ltd. Moncton 506-855-4228 ONTARIO Choquette CKS Ottawa 613-739-8458 R.G. Henderson Ltd. Toronto 416-422-5580 QUÉBEC Choquette CKS Montreal 514-722-2000 Choquette CKS Québec City 418-681-3944 Parts No. 07.04.404.00 Form No. GR3M-0807