Emerson EWC0901 Owner's Manual

EWC0901 OWNER’S MANUAL As an ENERGY STAR Partner, our company has determined that this product meets the ENERGY STAR guidelines for energy efficiency. ENERGY STAR is a U.S. registered mark. ® ® ® If you need additional assistance for set-up or operating after reading owner’s manual, please call TOLL FREE : 1-800-256-2487. Please read before using this equipment INSTRUCCIONES EN ESPAÑOL INCLUIDAS. This Owner’s Manual is made of recycled paper.

should be read before the appliance is operated. 2.Retain Instructions-The safety and operating instructions should be retained for future reference. 3.Heed Warnings-All warnings on the appliance and in the operating instructions should be adhered to. 4.Follow Instructions-All operating and use instructions should be followed. 5.Cleaning-Unplug TV/VCR from the wall outlet before cleaning. Do not use liquid cleaners or aerosol cleaners. Use a damp cloth for cleaning. EXCEPTION: A product that is meant for uninterrupted service and, that for some specific reason, such as the possi- bility of the loss of an authorization code for a CATV con- verter, is not intended to be unplugged by the user for clean- ing or any other purpose, may exclude the reference to unplugging the appliance in the cleaning description other- wise required in item 5. 6.Attachments-Do not use attachments not recommended by the TV/VCR manufacturer as they may cause hazards. 7.Water and Moisture-Do not use this TV/VCR near water- for example, near a bath tub, wash bowl, kitchen sink, or laundry tub, in a wet basement, or near a swimming pool, and the like. 8.Accessories-Do not place this TV/VCR on an unstable cart, stand, tripod, bracket, or table. The TV/VCR may fall, caus- ing serious injury to someone, and serious damage to the appliance. Use only with a cart, stand, tripod, bracket, or table recommended by the manufac- turer, or sold with the TV/VCR. Any mounting of the appliance should follow the manufacturer’s instruc- tions and should use a mounting accessory recommended by the man- ufacturer. An appliance and cart combination should be moved with care. Quick stops, excessive force, and uneven surfaces may cause the appliance and cart combination to overturn. 9.Ventilation-Slots and openings in the cabinet and the back or bottom are provided for ventilation and to ensure reliable operation of the TV/VCR and to protect it from overheat- ing, and these openings must not be blocked or covered. The openings should never be blocked by placing the TV/VCR on a bed, sofa, rug, or other similar surface. This TV/VCR should never be placed near or over a radiator or heat register. This TV/VCR should not be placed in a built- in installation such as a bookcase or rack unless proper ventilation is provided or the manufacturer’s instructions have been adhered to. 10.Power Sources-This TV/VCR should be operated only from the type of power source indicated on the marking label. If you are not sure of the type of power supply to your home, consult your appliance dealer or local power company. For TV/VCRs intended to operate from battery power, or other sources, refer to the operating instructions. 11.Grounding or Polarization-This TV/VCR is equipped with a polarized alternating-current line plug(a plug having one blade wider than the other). This plug will fit into the power outlet only one way. This is a safety feature. If you are unable to insert the plug fully into the outlet, try revers- ing the plug. If the plug should still fail to fit, contact your electrician to replace your obsolete outlet. Do not defeat the safety purpose of the polarized plug. 12.Power-Cord Protection-Power-supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against them, paying par- ticular attention to cords at plugs, convenience receptacles, and the point where they exit from the appliance. - 2 - EN 9J27 WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSON- NEL. CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN THIS SYMBOL INDICATES THAT DAN- GEROUS VOLTAGE CONSTITUTING A RISK OF ELECTRIC SHOCK IS PRESENT WITHIN THIS UNIT. THIS SYMBOL INDICATES THAT THERE ARE IMPORTANT OPERATING AND MAINTENANCE INSTRUCTIONS IN THE LITERATURE ACCOMPANYING THE APPLIANCE. The caution marking is located on the rear of the cabinet. IMPORTANT SAFEGUARDS PORTABLE CART WARNING S3126A

EN 9J27 13.Outdoor Antenna grounding-If an outside antenna or cable system is connected to the TV/VCR, be sure the antenna or cable system is grounded so as to provide some protection against voltage surges and built-up static charges. Article 810 of the National Electrical Code, ANSI/NFPA No. 70, provides information with respect to proper grounding of the mast and supporting structure, grounding of the lead-in wire to an antenna discharge unit, size of grounding conductors, location of antenna-discharge unit, connection to grounding electrodes, and requirements for the grounding electrode. (Fig. A) 14.Lightning-For added protection for this TV/VCR receiver during a lightning storm, or when it is left unattended and unused for long periods of time, unplug it from the wall outlet and disconnect the antenna or cable system. This will prevent damage to the TV/VCR due to lightning and power-line surges. 15.Power Lines-An outside antenna system should not be located in the vicinity of overhead power lines or other electric light or power circuits, or where it can fall into such power lines or circuits. When installing an outside antenna system, extreme care should be taken to keep from touching such power lines or circuits as contact with them might be fatal. 16.Overloading-Do not overload wall outlets and extension cords as this can result in a risk of fire or electric shock. 17.Object and Liquid Entry-Never push objects of any kind into this TV/VCR through openings as they may touch dan- gerous voltage points or short out parts that could result in a fire or electric shock. Never spill liquid of any kind on the TV/VCR. 18.Servicing-Do not attempt to service this TV/VCR yourself as opening or removing covers may expose you to danger- ous voltage or other hazards. Refer all servicing to quali- fied service personnel. 19.Damage Requiring Service-Unplug this TV/VCR from the wall outlet and refer servicing to qualified service per- sonnel under the following conditions: a. When the power-supply cord or plug is damaged or frayed. b. If liquid has been spilled, or objects have fallen into the TV/VCR. c. If the TV/VCR has been exposed to rain or water. d. If the TV/VCR does not operate normally by following the operating instructions. Adjust only those controls that are covered by the operating instructions, as improper adjust- ment of other controls may result in damage and will often require extensive work by a qualified technician to restore the TV/VCR to its normal operation. e. If the TV/VCR has been dropped or damaged in any way. f. When the TV/VCR exhibits a distinct change in perfor- mance-this indicates a need for service. 20.Replacement Parts-When replacement parts are required, be sure the service technician has used replacement parts specified by the manufacturer that have the same character- istics as the original part. Unauthorized substitutions may result in fire, electric shock, injury to persons or other haz- ards. 21.Safety Check-Upon completion of any service or repairs to this TV/VCR, ask the service technician to perform routine safety checks to determine that the TV/VCR is in proper operating condition. 22.Heat-This TV/VCR product should be situated away from heat sources such as radiators, heat registers, stoves, or other products (including amplifiers) that produce heat. GROUND CLAMPS NEC - NATIONAL ELECTRICAL CODE EXAMPLE OF ANTENNA GROUNDING AS PER NATIONAL ELECTRICAL CODE S2898A WI RE DISCHARGE UNIT (NEC SECTION 810-20) GROUNDING CONDUCTORS (NEC SECTION 810-21) ELECTRODE SYSTEM (NEC ART 250, PART H) SERVICE EQUIPMENT CL AM P ANTENNA LEAD I N ANTENNA POWER SERVICE GROUNDING GROUND ELECTRI C FIGURE A

ELECTRICAL SHOCK AND FIRE This equipment has been tested and found to com- ply with the limits for a Class B digital device, pur- suant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be deter- mined by turning the equipment off and on, the user is encouraged to try to correct the interfer- ence by one or more of the following measures: 1) Reorient or relocate the receiving antenna. 2) Increase the separation between the equipment and receiver. 3) Connect the equipment into an outlet on a cir- cuit different from that to which the receiver is connected. 4) Consult the dealer or an experienced radio/TV technician for help. - 4 - EN 9J27 PRECAUTIONS LOCATION For safe operation and satisfactory performance of your TV/VCR, keep the following in mind when selecting a place for its installation: • Shield it from direct sunlight and keep it away from sources of intense heat. • Avoid dusty or humid places. • Avoid places with insufficient ventilation for proper heat dissipation. Do not block the ventilation holes at the top and bottom of the unit. Do not place the unit on a carpet because this will block the ventila- tion holes. • Install unit in a horizontal position. • Avoid locations subject to strong vibration. • Do not place the TV/VCR near strong magnetic fields. • Avoid moving TV/VCR to locations where temper- ature differences are extreme. • Do not handle the power cord with wet hands. • Do not pull on the power cord when disconnecting it from an AC wall outlet. Grasp it by the plug. • If, by accident, water is spilled on your unit, unplug the power cord immediately and take the unit to our Authorized Service Center for servicing. • Do not put your fingers or objects into the TV/VCR cassette holder. • Do not place anything directly on top of the unit. WARNING Moisture condensation may occur inside the unit when it is moved from a cold place to a warm place, or after heating a cold room or under conditions of high humidity. If a tape is played in a TV/VCR which has moisture, it may damage the tape and TV/VCR. Therefore when the condensation occurs inside the unit, “DEW” appears on the screen. In this case, turn the POWER button on and allow at least 2 hours for the unit to dry out. IMPORTANT COPYRIGHT INFORMATION Unauthorized recording or use of broadcast televi- sion programming, video tape, film or other copy- righted material may violate applicable copyright laws. We assume no responsibility for the unautho- rized duplication, use, or other acts which infringe upon the rights of copyright owners. FCC WARNING- This equipment may gener- ate or use radio frequency energy. Changes or modifications to this equipment may cause harmful interference unless the modifications are expressly approved in the instruction man- ual. The user could lose the authority to oper- ate this equipment if an unauthorized change or modification is made. The serial number of this product may be found on the back of the unit. No other TV/VCR has the same serial number as yours. You should record the number and other vital information here and retain this book as a per- manent record of your purchase to aid identification in case of theft. Serial numbers are not kept on file. Date of Purchase Dealer Purchase from Dealer Address Dealer Phone No. Model No. Serial No.

EN 9J27 TABLE OF CONTENTS A NOTE ABOUT RECYCLING This product’s packaging materials are recyclable and can be reused. Please dispose of any materials in accordance with your local recycling regulations. Batteries should never be thrown away or incinerated but disposed of in accordance with your local regula- tions concerning chemical wastes. C IMPORTANT SAFEGUARDS . . . . . . . . . . . . .2 C PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . .4 LOCATION . . . . . . . . . . . . . . . . . . . . . . . . . . . .4 AVOID THE HAZARDS OF ELECTRICAL SHOCK AND FIRE . . . . . . . . . . . . . . . . . . . . . .4 WARNING . . . . . . . . . . . . . . . . . . . . . . . . . . . .4 C FEATURES . . . . . . . . . . . . . . . . . . . . . . . . . . . .6 C SUPPLIED ACCESSORIES . . . . . . . . . . . . . . .6 C OPERATING CONTROLS AND FUNCTIONS 7 C PREPARATION FOR USE . . . . . . . . . . . . . . . .9 ANTENNA/CABLE CONNECTIONS . . . . . . .9 INSTALLING THE BATTERIES . . . . . . . . . . .10 EXTERNAL INPUT MODE . . . . . . . . . . . . . .10 MOBILE CONNECTION . . . . . . . . . . . . . . . .10 C SET UP FOR USE . . . . . . . . . . . . . . . . . . . . . .11 CHANNEL SET UP FOR THE FIRST TIME . .11 CLOCK SET UP (AUTO / MANUAL) . . . . . .12 CHANNEL SET UP AGAIN . . . . . . . . . . . . . .13 DELETING (OR ADDING) CHANNEL . . . . .13 SELECTING THE LANGUAGE . . . . . . . . . . .14 DAYLIGHT-SAVING TIME . . . . . . . . . . . . . .14 C TV OPERATION . . . . . . . . . . . . . . . . . . . . . . .15 WATCHING A TV PROGRAM . . . . . . . . . . . .15 GAME MODE . . . . . . . . . . . . . . . . . . . . . . . . .15 DEGAUSSING . . . . . . . . . . . . . . . . . . . . . . . .15 PICTURE CONTROL . . . . . . . . . . . . . . . . . . .15 C PLAYBACK . . . . . . . . . . . . . . . . . . . . . . . . . . .16 NORMAL PLAYBACK . . . . . . . . . . . . . . . . . .16 AUTO REPEAT PLAYBACK . . . . . . . . . . . . .16 SEARCH . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17 STILL PICTURE . . . . . . . . . . . . . . . . . . . . . . .17 PICTURE CONROLS . . . . . . . . . . . . . . . . . . .18 C RECORDING . . . . . . . . . . . . . . . . . . . . . . . . .18 NORMAL RECORDING . . . . . . . . . . . . . . . . .19 SKIPPING UNWANTED SCENES DURING RECORDING . . . . . . . . . . . . . . . . . . . . . . . . .19 OTR (One Touch Recording) . . . . . . . . . . . . . .19 TIMER RECORDING . . . . . . . . . . . . . . . . . . .20 TIMER PROGRAM EXTENSION . . . . . . . . .31 HINTS FOR AUTOMATIC TIMER RECORDING . . . . . . . . . . . . . . . . . . . . . . . . .22 AUTO RETURN . . . . . . . . . . . . . . . . . . . . . . .22 WAKE UP TIMER . . . . . . . . . . . . . . . . . . . . . .22 SLEEP TIMER . . . . . . . . . . . . . . . . . . . . . . . . .23 C COPYING A VIDEO CASSETTE . . . . . . . . . .28 C ON SCREEN DISPLAY . . . . . . . . . . . . . . . . .24 C SPECIAL FEATURES . . . . . . . . . . . . . . . . . .24 REAL TIME TAPE COUNTER . . . . . . . . . . . .24 AUTO REWIND-EJECT . . . . . . . . . . . . . . . . .24 C MAINTENANCE . . . . . . . . . . . . . . . . . . . . . . .24 C TROUBLESHOOTING GUIDE . . . . . . . . . . .25 C SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . .26 C CABLE CHANNEL DESIGNATIONS . . . . . .26 C WARRANTY . . . . . . . . . . . . . . . . . . .Back Cover INDICE CONTROLES DE OPERACIÓN Y SUS FUNCIONES . . . . . . . . . . . . . . . . . . . . . . . .29 CONEXIONES DE ANTENA/CABLE . . . . . . . .30 MODO DE ENTRADA EXTERNA . . . . . . . . . . .30 INSTALACIÓN DE LAS PILAS . . . . . . . . . . . . .30 PREPARACIÓN DE CANALES POR PRIMERA VEZ . . . . . . . . . . . . . . . . . . . . . . . . . .31 AJUSTE DEL RELOJ . . . . . . . . . . . . . . . . . . . . .31

EN 9J27 FEATURES • Infrared remote control • Dew Sensor–Indicates that moisture condensation may occur inside the TV/VCR. • Bilingual on screen menu display selectable in English or Spanish • Real time counter–This shows the elapsed recording or playback time in hours, minutes, and seconds. The “–” indication will appear when the tape is rewound further than the tape counter position “0:00:00”. • 181 channel capability PLL frequency synthesizer tuner with direct station call–(A converter may be nec- essary to view scrambled cable channels.) • Auto Clock Setting–Allows you to set the clock function from a PBS broadcast station. • Game mode–Automatically sets external input mode and allows TV/VCR display to be suitable for use with TV games. • Auto power on and off system–Automatically turns on the TV/VCR when you insert the cassette, turns off after auto-rewind, and ejects when the beginning of the tape is reached. • Auto rewind when the end of a tape is reached–This function doesn’t occur when using timer recording. • 2 Step picture search operation–You can view a video program at a high speed or super high speed in either a forward or reverse direction in LP and SLP mode. For SP mode only high speed. • Three different playback tape speeds : SP/LP/SLP • Two different recording tape speeds : SP/SLP • Auto Head Cleaner–Automatically cleans video heads as you insert or remove a cassette. • Zero Return–The tape returns to counter of 0:00:00 by rewinding or fast forwarding. • Still–“Freeze” the picture at any time, for close viewing of a particular scene. Only tapes recorded in SLP mode will show a fairly clear picture. • Digital Auto Tracking (DTR)–Automatically adjusts the tracking for each tape you play. • Rental play mode–Improves playback picture quality from worn tapes, such as rental tapes. • Auto repeat–Allows you to repeat the playing of a tape indefinitely without pressing the PLAY button. • Time search–Let you set the TV/VCR to advance the tape by entering the desired playback time you want to skip. • OTR (One Touch Recording)–Instant timed recording from 30 to 480 minutes is possible at the push of the REC/OTR button. • 1 Year, 8 events (including Daily and Weekly Timer Recording)–The built-in timer allows you to record up to 8 programs at different times on different channels up to 1 year in advance. The Daily timer allows recordings to be made of daily broadcasts, and the Weekly timer allows recording to be made once a week up to the end of the tape. • Auto return–After timer recording is finished, the TV/VCR can return to the beginning of the recording. • Wake up/Sleep timer–Allows you to have the TV/VCR automatically turn on or off at a desired time. • Timer Program Extension–Allow you to shift the time schedule for automatic timer recording. • Two- way power–Allows you to power the TV/VCR with standard household AC or your vehicle’s battery, using the supplied car-battery cord. SUPPLIED ACCESSORIES • If you need to replace these accessories, please refer to the PART NO. under the illustrations and call 1-800- 256-2487. • Depending on your antenna system, you may need different types of Combiners (Mixer) or Separators (Splitter). Contact your local electronics store for these items. • We do not recommend the use of universal remote controls. Not all of the functions may be controlled with a universal remote control. If you decide to use a universal remote control with this unit, please be aware that the code number given may not operate this unit. In this case, please call the manufacturer of the uni- versal remote control. Car Battery Cord Matching Adapter (300ohm-75ohm) AC Cord WPZ0202GA004 WAV0182NW001/WAV0182LW001 2 AA Batteries (1813641/1780103) Dipole Antenna (0EMN00723) Remote Control Unit PART NO. (N0107UD)

EN 9J27 OPERATING CONTROLS AND FUNCTIONS NOTE: • We do not recommend the use of universal remote controls. Not all of the functions may be controlled with a universal remote control. If you decide to use a universal remote control with this unit, please be aware that the code number given may not operate this unit. In this case, please call the manufacturer of the universal remote control. - TV/VCR FRONT PANEL - [Fig.1] 2 VIDEO input jack– Connect to the video output jack of your video camera or another VCR. 3 RECORD indicator– Flashes during recording. Lights up in the Stand-by mode for Timer Recording. 4 Remote Sensor Window– Receives the infrared signals from the remote control. 5 POWER button– Press to turn TV/VCR on and off. Press to activate timer recording. 6 STOP button– Press to stop the tape motion. EJECT button– Press in the Stop mode to remove tape from TV/VCR. L button– • Press to select setting modes from the on screen menu. • Press to enter digits when setting program. (for example: setting clock or timer program) 7 REW button– Press to rew¨ind the tape, or to view the picture rapidly in reverse during playback mode. (Rewind Search) s button– • Press to select a mode from a particular menu. (for example: LANGUAGE or USER’S SET UP) 8 PLAY button– Press to begin playback. K button– • Press to select setting modes from the on screen menu. • Press to enter digits when setting program. (for example: setting clock or timer program) - REMOTE CONTROL - [Fig.2] AUDIO VIDEO REC POWER STOP/EJECT rREW PLAY F.FWDq REC/OTR VOLUME CHANNEL EARPHONE 1 2 9 3 4 5 6 7 8 12 13 10 11 14 POWER WAKE-UP /SLEEP 1 2 3 4 5 6 7 8 9 +100 0 EJECT CHANNEL RETURN REW PLAY STOP F.FWD GAME RECORD PAUSE/STILL SPEED TIME SEARCH CHANNEL T-PROG. CLEAR COUNTER RESET DISPLAY MUTE MENU VOLUME 5 15 12 6 16 7 10 18 19 20 6 24 11 9 8 22 21 23 17 25 1 AUDIO input jack– Connect to the audio output jack of your audio equipment, video camera or another VCR. Fig.2 Fig.1

EN 9J27 - REAR VIEW - [Fig.3] 26 27 28 AC 120V ANT DC 13.2V 9 F.FWD button– Press to rapidly advance the tape, or to view the picture rapidly in forward during playback mode. (Forward Search) B button– • When setting program (for example: setting clock or timer program), press to determine your selec- tion and proceed to the next step you want to input. • Press to determine setting modes from on screen menu. • Press to select a mode from a particular menu. (for example: LANGUAGE or USER’S SET UP) 10 REC button– Press for manual recording. OTR button– Activates One Touch Recording. (only on the TV/VCR) 11 VOLUME X / Y buttons– Adjust the volume level. 12 CHANNEL K / L buttons– Press to select the desired channels for viewing or recording. You may display the main menu on the TV screen by pressing repeatedly this button on the TV/VCR. TRACKING function– Press to minimize video ‘noise’ (lines or dots on screen) during playback mode. (See page 19.) 13 EARPHONE jack– Connects to earphones (not supplied) for personal listening. The size of jack is 1/8” monaural (3.5mm). 14 Cassette compartment 15 Number buttons– Press to select desired channels for viewing or recording. To select channels from 1 to 9, first press the 0 button and then 1 to 9. +100 button– When selecting cable channels which are higher than 99, press this button first, then press the last two digits. (To select channel 125, first press the “+100” button then press “2” and “5”). 16 MENU button– Press to display the main menu on the TV screen. 17 DISPLAY button– Display the counter or the cur- rent channel number and current time on the TV screen. (See page 17.) 18 SPEED button– Press to choose the desired recording speed:SP/SLP. 19 T-PROG. CLEAR button– Press to cancel a setting of timer program. (See page 25.) COUNTER RESET button– Press to reset counter to 0:00:00. 20 GAME button– Sets the game mode and external input mode at the same time. (See page 18.) 21 TIME SEARCH button– Press to activate Time Search mode. 22 PAUSE/STILL button– Press to temporarily stop the tape during the recording or to view a still pic- ture during playback. 23 MUTE button– Mutes the sound. Press it again to resume sound. 24 CHANNEL RETURN button– Press to go back to the previously viewed channel. For example, pressing this button once will change channel dis- play from 3 (present channel) to 10 (previously viewed channel), and pressing it a second time will return from 10 to 3. 25 WAKE UP/SLEEP button– Sets the Wake up or Sleep Timer. (See page 26.) 26 ANT. terminal– Connect to an antenna or cable system. 27 DC 13.2V jack– Connect to the Car Battery Cord. 28 AC 120V jack– Connect to the AC cord. Fig.3

EN 9J27 ANTENNA/CABLE CONNECTIONS DIPOLE ANTENNA HOOK UP 1. Push the stem of the Dipole Antenna (accessory) into the hole for antenna at the back of TV/VCR. 2. Connect the flat twin-lead cable from the Dipole Antenna to the 300/75 ohm Matching Adapter (accessory). 3. Plug the Matching Adapter to ANT terminal of TV/VCR as shown in drawing. For the best reception, extend the Dipole Antenna and adjust its length and position. (Avoid handling the top section when making adjustments). NOTE: If it is difficult to get good reception with the indoor antenna, the use of an outdoor antenna is recommended. Before an outdoor antenna is connect- ed to the set, the indoor antenna should be discon- nected. CABLE WITHOUT CONVERTER/ DESCRAMBLER BOX Use this connection if your cable system connects directly to your TV/VCR without a converter box. By using this connection you can: 1) Use the TV/VCR remote to select channels. 2) Program one or more unscrambled channels for Automatic Timer Recording. NOTE: This unit will ONLY record and view the same channel. VHF/UHF SEPARATE ANTENNAS In some areas it will be necessary to use an outdoor antenna. VHF/UHF COMBINED ANTENNA A VHF UHF 75 ohm combination antenna can be connected to ANT terminal. Note to CATV system installer: This reminder is provided to call the CATV system installer’s attention to Article 820-40 of the NEC that provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be connect- ed to the grounding system of the building as close to the point of cable entry as practical. Antenna/Cable Connections Continued on the Next Page. ANT. IN OUT AC 120V ANT DC 13.2V Dipole Antenna (Supplied) VHF/UHF Antenna (Not supplied) VHF/UHF Combiner (Not supplied) Flat twin-lead cable UHF Antenna (Not supplied) VHF Antenna (Not supplied) From Cable System 75-ohm Coaxial Cable (Not supplied) Satellite Box or Cable Box (Not supplied) From Cable System or Satellite Dish or or or or Flat twin-lead cable PREPARATION FOR USE Fig.4

EN 9J27 INSTALLING THE BATTERIES 1)Open the battery compartment cover by pressing the cover on the remote unit in the direction of the arrow. 2)Insert 2 “AA” penlight batteries into the battery compartment in the direction indicated by the polarity (+/-) markings. 3)Replace the cover. EXTERNAL INPUT MODE When using an external input signal (another VCR or video camera), connect the player’s audio/video out- put cables to the AUDIO IN/ VIDEO IN jacks of your TV/VCR. Then press the CHANNEL K or L button until “AUX” appears on the screen. AUX TO RECORD A SCRAMBLED/UNSCRAMBLED CHANNEL 1. Set the TV/VCR channel selector to the output channel of the Cable Converter Box or Satellite Box. (Ex. CH3) 2.Select the channel to record from your Cable Converter Box or Satellite Box. MOBILE CONNECTION 1) The supplied indoor antenna is adequate when your vehicle is stationary. For best reception on the road, use a high-quality VHF/UHF mobile TV antenna. 2) Attach the car battery cord to the DC13.2V con- nector on the back of the TV/VCR. Then, connect the other end to your vehicle’s cigarette-lighter socket. NOTES: • Be sure your vehicle has a 13.2-volt, negative- ground electrical system. • Be sure you use only the supplied car battery cord. Using another cord could damage the TV/VCR. • Be sure the socket is free of ashes and other debris. • Be sure to push the car battery cord’s plug com- pletely into the cigarette-lighter socket. • Always unplug the car battery from the cigarette- lighter socket before you unplug it from the TV/VCR. • You must disconnect the car battery cord from the TV/VCR before you can use the AC power. • Be sure to replace the fuse with only the same type, 5A, 250V. WARNING: The driver should never watch the TV/VCR while operating a motor vehicle. CAUTION: If you use the TV/VCR with the vehicle’s engine off, recharge the vehicle’s battery after about every 4 hours of use to prevent it from running down. After you fin- ish using the TV/VCR be sure you unplug the car-battery cord from the cigarette-lighter socket. VHF/UHF Combination Mobile Antenna (Not supplied) Car battery cord (Supplied) To the vehicle's cigarette-lighter socket ANT. DC13.2V [Fig.8] CABLE WITH CONVERTER/ DESCRAMBLER BOX OR SATELLITE BOX If your cable service supplies you with a converter box or if you use a satellite system, you can use the basic connection shown here. By using this connection you can also record scram- bled channels. However, channel selection must be made with the converter box or satellite box. This means that channels cannot be changed using the TV/VCR Remote Control. Unattended timer record- ing is limited to one channel at a time.

EN 9J27 SET UP FOR USE You can program the tuner to scan all the channels you receive in your area. NOTE: Channel memory programming is NOT needed when connected to a cable box or satellite box. Just select the TV/VCR channel selector to the output channel of the cable box or satellite box (Ex CH3). Then select the channel to be viewed on the Cable Box or Satellite Box. CHANNEL SET UP FOR THE FIRST TIME 1 Plug in the TV/VCR power cord Attach the smaller end of the sup- plied AC cord to the AC 120V connector on the back of the TV/VCR. Then, plug the other end into a standard AC outlet. NOTES: • You must disconnect the car battery cord from the TV/VCR before you use AC power. • If some digits appear in the corner of the screen, press the POWER button without unplugging the power cord. 2 Turn on the TV/VCR Press the POWER button to turn on the TV/VCR. 3 Select “ENGLISH” or “ESPAÑOL” Select “ENGLISH” or “ESPAÑOL”=Spanish using the F.FWD/B or REW/s button. “[ ]” indicate the selected language. 4 Begin auto preset Press the PLAY/K or STOP/L but- ton to point to “AUTO PRESET”. Then press the F.FWD/B button. The tuner scans and memorizes all active channels in your area. NOTES: • The TV/VCR distinguishes between standard TV channels and cable channels. • If you want to play or record a video tape BEFORE presetting the tuner, you must press the MENU but- ton on the remote control. To preset the tuner again, see “CHANNEL SET UP AGAIN” on page 14. • The TV/VCR may recognize TV channels to be CATV channels by the receiving conditions. In this case, try auto preset again in the fine receiving conditions. 5 After scanning The tuner stops on the lowest memorized channel. If you want to recall the selected channels, you can select the desired channel directly with the remote control number buttons or CHANNEL K or L. AC 120V – SET UP – B LANGUAGE [ENGLISH] ESPAÑOL AUTO PRESET – SET UP – LANGUAGE [ENGLISH] ESPAÑOL B AUTO PRESET TO SELECT ADESIRED CHANNEL You can select the desires channel by using the CHANNEL K or L button on or directly pressing the number buttons on the remote control. Note for using the number buttons: • When selecting cable channels which are higher than 99, press the +100 button first, then, press the last tw odigts. (Example: to select channel 125, first press the +100 button then press “2” and “5”). • You must procede single-digit channel numbers with a zero (Example: 02 ... 09). CLOCK SET UP (AUTO / MANUAL) Set the clock accurately for proper automatic timer recording. If the Public Broadcasting Station (PBS) is available in your area, follow “AUTO CLOCK SETTING”. If it is not, follow “MANUAL CLOCK SETTING”. AUTO CLOCK SETTING You can have the TV/VCR set the clock automatical- ly by using the Public Broadcasting Station (PBS) channel in your area. Once you have set the clock by using the following procedure, the TV/VCR will automatically monitor the correct time and date being broadcast by the PBS station in your area, using a new service called Extended Data Service (XDS). Make sure ... • TV/VCR power must be turned on. • Confirm that the antenna connections are correct. • The cable converter box must be turned on if your TV/VCR is connected directly to it. (See NOTES:) • The channel is properly set in advance.

EN 9J27 NOTES: • Auto clock setting only needs to be set once. But it can be done again if the clock’s time has become incorrect for some reason. • If the TV/VCR is connected directly to a cable converter box or satellite box, the local PBS station must be selected on the cable box itself, and the TV/VCR must be set to the output channel of the cable converter box or satellite box (usually chan- nel 3 or 4), to be able to set up or correct the clock automatically. If you do not know what your local PBS station is, then follow “Manual Clock Settings”. The TV/VCR cannot control the channels of the cable converter box or satellite box. 1 Select “SETTING CLOCK” Press the MENU button on the remote control. Press the PLAY/K or STOP/L but- ton to point to “SETTING CLOCK”. Then, press the F.FWD/B button. 2 Set “AUTO CLOCK” to [ON] Press the F.FWD/B or REW/s button repeatedly until [ON] appears. 3 Enter the channel number for the PBS station Press the PLAY/K or STOP/L button to point to “AUTO CLOCK CH”. Then press the F.FWD/B or REW/s button until the channel number for your local PBS station appears. If you do not know the PBS channel number, leave it set to [AUTO] which is located before [2]. The TV/VCR will search automatically all available chan- nels for the local PBS station, and will select that channel. 4 Exit the Auto Clock Setting Press the MENU button on the remote control to return to TV mode. 5 Turn off the TV/VCR Turn the TV/VCR off. Because the Auto Clock func- tions automatically while the TV/VCR is off. – SETTING CLOCK – B AUTO CLOCK [ON] AUTO CLOCK CH [AUTO] MANUAL CLOCK SET D.S.T. [OFF] – SETTING CLOCK – AUTO CLOCK [ON] B AUTO CLOCK CH [AUTO] MANUAL CLOCK SET D.S.T. [OFF] – M E N U – TIMER PROGRAMMING PICTURE CONTROL B SETTING CLOCK CHANNEL SET UP USER’S SET UP LANGUAGE [ENGLISH] ZERO RETURN TIME SEARCH If you choose [AUTO], • The TV/VCR must search until the PBS channel is found. It must scan each channel for a couple of seconds to determine if that channel is transmitting the XDS signal. • If the time, that is automatically set by this select- ed PBS station is incorrect, it may not be your local PBS station, but one from a different time zone. Or there is a case that no channel is broad- casting the XDS signal in your area, as shown by no time. In these cases, you must manually enter the correct local PBS station, or set the clock man- ually and turn off the Auto Clock Setting feature. MANUAL CLOCK SETTING Make sure ... • TV/VCR power must be turned on. In the example below, the clock is to be set to: DATE May 1st, 2001 SETTING TIME 5:40PM 1 Select “SETTING CLOCK” Press the MENU button on the remote control. Press the PLAY/K or STOP/L but- ton to point to “SETTING CLOCK”. Then, press the F.FWD/B button. 2 Select “MANUAL CLOCK SET” Press the PLAY/K or STOP/L but- ton to point to “MANUAL CLOCK SET”. Then, press the F.FWD/B button. 3 Select the month Press the PLAY/K or STOP/L but- ton until your desired month appears. (Example: May →05) Then, press the F.FWD/B button. 4 Select the day Press the PLAY/K or STOP/L but- ton until your desired day appears. (Example: 1st →01) Then, press the F.FWD/B button. – M E N U – TIMER PROGRAMMING PICTURE CONTROL B SETTING CLOCK CHANNEL SET UP USER’S SET UP LANGUAGE [ENGLISH] ZERO RETURN TIME SEARCH – SETTING CLOCK – AUTO CLOCK [ON] AUTO CLOCK CH [AUTO] B MANUAL CLOCK SET D.S.T. [OFF] – MANUAL CLOCK SET – MONTH DAY YEAR 0 5 / – – – – – – – – – HOUR MINUTE – – : – – – – – MANUAL CLOCK SET – MONTH DAY YEAR 0 5 / 0 1 – – – – – – – HOUR MINUTE – – : – – – –

EN 9J27 CHANNEL SET UP AGAIN Make sure ... • Press the POWER button to turn on the TV/VCR. 1 Select “CHANNEL SET UP” Press the MENU button on the remote control. Press the PLAY/K or STOP/L but- ton to point to “CHANNEL SET UP”. Then, press the F.FWD/B button. 2 Begin auto preset Press the PLAY/K or STOP/L but- ton to point to “AUTO PRESET”. Then, press the F.FWD/B button. The tuner scans and memorizes all the active channels in your area. 3 After scanning The tuner stops on the lowest memorized channel. – M E N U – TIMER PROGRAMMING PICTURE CONTROL SETTING CLOCK B CHANNEL SET UP USER’S SET UP LANGUAGE [ENGLISH] ZERO RETURN TIME SEARCH – CHANNEL SET UP – ADD / DELETE CH (TV) B AUTO PRESET 5 Select the year Press the PLAY/K or STOP/L but- ton until your desired year appears. (Example: 2001) Then, press the F.FWD/B button. 6 Select the hour Press the PLAY/K or STOP/L but- ton until your desired hour appears. (Example: 5, PM) Then, press the F.FWD/B button. 7 Select the minute Press the PLAY/K or STOP/L but- ton until the desired minute appears. (Example: 40) 8 Start the clock Press the MENU button on the remote control. Although seconds are not displayed, they begin counting from 00 when you press the MENU button on the remote control. Use this feature to synchronize the clock with the correct time. NOTE: When unplugging the AC cord or if there is a power failure for more than 30 seconds, you may have to reset the clock. TO CHANGE CLOCK SETTING If you want to change the clock, 1)Follow steps [1] and [2]. 2)Select where you want to change using the F.FWD/B or REW/s button. 3)Enter correct numbers using the PLAY/K or STOP/L button. 4)Press the MENU button on the remote control to start the clock. PLEASE NOTE: If there is no local PBS station in your area or on your cable system, select “AUTO CLOCK” and press the F.FWD/B or REW/s button to turn [OFF] this function. Then you can manually adjust the clock. – MANUAL CLOCK SET – MONTH DAY YEAR 0 5 / 0 1 TUE 2 0 0 1 HOUR MINUTE 0 5 : – – PM – MANUAL CLOCK SET – MONTH DAY YEAR 0 5 / 0 1 TUE 2 0 0 1 HOUR MINUTE 0 5 : 4 0 PM 5:40 PM – MANUAL CLOCK SET – MONTH DAY YEAR 0 5 / 0 1 TUE 2 0 0 1 HOUR MINUTE – – : – – – – DELETING (OR ADDING) CHANNEL The channels you no longer receive or seldom watch can be deleted from the memory. (Of course, you can add the deleted channel into the memory again.) 1 Select “CHANNEL SET UP” Press the MENU button on the remote control. Then press the PLAY/K or STOP/L button to point to “CHANNEL SET UP”. Then, press the F.FWD/B button. 2 Select “ADD/DELETE CH” Press the PLAY/K or STOP/L but- ton to point to “ADD/DELETE CH”. Press the F.FWD/B button. 3 Enter the desired channel number Press the PLAY/K or STOP/L but- ton until your desired channel num- ber appears. (You can also use the number buttons or the CHANNEL K/L button to enter it) (Example: CH8) – M E N U – TIMER PROGRAMMING PICTURE CONTROL SETTING CLOCK B CHANNEL SET UP USER’S SET UP LANGUAGE [ENGLISH] ZERO RETURN TIME SEARCH – CHANNEL SET UP – B ADD / DELETE CH (TV) AUTO PRESET 08 ADD / DELETE

EN 9J27 SELECTING THE LANGUAGE Make sure ... • Press the POWER button to turn on the TV/VCR. NOTE: This function effects only the language on the screen menu and not the audio source. 1 Select “LANGUAGE” Press the MENU button on the remote control. Press the PLAY/K or STOP/L but- ton to point to “LANGUAGE”. 2 Select “ENGLISH” or “ESPAÑOL” Select “ENGLISH” or “ESPAÑOL”= Spanish using the F.FWD/B or REW/s button. 3 Exit the Language mode Press the MENU button on the remote control to return to TV mode. NOTE: If for some reason the menu is in Spanish, press the MENU button on the remote control, press the PLAY/K button to point to “IDIOMA [ESPAÑOL]”, then press the F.FWD/B button, then press the MENU button on the remote control. – M E N U – TIMER PROGRAMMING PICTURE CONTROL SETTING CLOCK CHANNEL SET UP USER’S SET UP B LANGUAGE [ENGLISH] ZERO RETURN TIME SEARCH 4 Delete (or add) it from (into) memory Press the F.FWD/B or REW/s button. The channel number changes to light red. The channel is deleted from memory. • To delete another channel, repeat steps [3] and [4]. • If you press the F.FWD/B or REW/s button again, the channel is memorized again. 5 Exit the channel setup mode Press the MENU button on the remote control to returns to TV mode. NOTE: To confirm that channel(s) has been deleted or added, press the CHANNEL K or L button. Added channel: Light blue. Deleted channel: Light red. DAYLIGHT-SAVING TIME Select this feature and the TV/VCR’s clock automati- cally will advance one hour in April, then reverse one hour in October. When Daylight-Saving Time is ON, the clock will change automatically as follows: • First Sunday of April : At 2 AM the clock imme- diately changes to 3 AM. Any timer programming you have set to occur between 2 AM and 3 AM will not record. • Last Sunday of October : At 2 AM the clock immediately changes to 1 AM. Make sure ... • Press the POWER button to turn on the TV/VCR. 1 Select “SETTING CLOCK” Press the MENU button on the remote control. Press the PLAY/K or STOP/L but- ton to point to “SETTING CLOCK”. Then, press the F.FWD/B button. 2 Set “D.S.T.” (Daylight-Saving Time) to [ON] Press the PLAY/K or STOP/L but- ton to point to “D.S.T.”. Then, press the F.FWD/B or REW/s button until [ON] appears. 3 Exit the Daylight-Saving Time mode Press the MENU button on the remote control to return to TV mode. TO CANCEL THE DAYLIGHT-SAVING TIME Repeat steps [1] to [2], select [OFF] using the F.FWD/B or REW/s button. – M E N U – TIMER PROGRAMMING PICTURE CONTROL B SETTING CLOCK CHANNEL SET UP USER’S SET UP LANGUAGE [ENGLISH] ZERO RETURN TIME SEARCH – SETTING CLOCK – AUTO CLOCK [ON] AUTO CLOCK CH [AUTO] MANUAL CLOCK SET B D.S.T. [ON]

EN 9J27 TV OPERATION WATCHING A TV PROGRAM 1 Turn on the TV/VCR Press the POWER button to turn on the TV/VCR. 2 Select the channel number Press the CHANNEL K or L button to select your desired channel number or press the number buttons on the remote control. Remember: If the TV/VCR is connected to a cable box or satellite box, the TV/VCR must be on CH3 or CH4, then the channel to be viewed must be selected on the cable box or satellite box. 3 Adjust sound Press the VOLUME X or Y button to adjust the volume. REW/s F.FWD/B BRIGHT to decrease to increase brightness brightness CONTRAST to decrease to increase contrast contrast COLOR to pale to brilliant TINT to purple to green SHARPNESS to soft to clear GAME MODE This function enables you to decrease the TV screen contrast and making it suitable for use with a TV GAME. NOTE: This function can not be set during recording. Press the GAME button on the remote control. “GAME” appears on the screen. When you press the GAME button; • The TV/VCR comes on automatically if it is off. • The TV/VCR will be in external input mode auto- matically. TO CANCEL THE GAME MODE Press the GAME button or CHANNEL K or L but- ton on the remote control. PICTURE CONTROL The TV/VCR’s picture controls – BRIGHT, CON- TRAST, COLOR, TINT and SHARPNESS – are preset to factory specifications. Although they are usually the best, you may need to make some further adjustments for a natural looking image. NOTES: • Procedures must be followed within 5 seconds or the Picture Control mode will be cancelled. • When setting the Picture Control, the Game mode will be cancelled. Make sure ... • TV/VCR power must be turned on. 1 Select “PICTURE CONTROL” Press the MENU button on the remote control. Press the PLAY/K or STOP/L but- ton to point to ”PICTURE CON- TROL”. Then, press the F.FWD/B button. 2 Select item you want to adjust Press the PLAY/K or STOP/L but- ton until desired control is dis- played. BRIGHT CONTRAST COLOR TINT SHARPNESS 3 Adjust the picture control Press the F.FWD/B or REW/s button to adjust to your desired level. • If there is a power failure of any kind, the unit will retain its memory for this feature. VOLUME 20 C C C C C C C C C C C C GAME – M E N U – TIMER PROGRAMMING B PICTURE CONTROL SETTING CLOCK CHANNEL SET UP USER’S SET UP LANGUAGE [ENGLISH] ZERO RETURN TIME SEARCH BRIGHT – P P P P P P P C P P P P P P P + DEGAUSSING Magnetism from nearby appliances might affect the color of the TV picture. If this happens, move this unit away from the appli- ance. If the color is still not correct, disconnect power cord from AC outlet then reconnect it after 30 minutes.

EN 9J27 PLAYBACK NORMAL PLAYBACK Make sure ... • TV/VCR power must be turned on. 1 Insert a prerecorded tape If the erase-protection tab has been removed, the TV/VCR will start playback automatically. 2 To begin playback Press the PLAY button. 3 To stop playback Press the STOP button when play- back is completed. PLAY B STOP This TV/VCR will operate with any cassette that has the mark. For best results, we recommend the use of high-quality tapes. Do not use poor quality or damaged tapes. PRECAUTIONS • Avoid moisture. Moisture condensation may occur on the tape if it is moved from a cold place to a warm place or visa versa. Before using a tape with these conditions, to avoid damage of the tape and your TV/VCR, wait until the tape has warmed to room temperature and the moisture has evaporated. • Avoid extreme heat, high humidity and magnetic fields. • Do not tamper with the cassette mechanism. • Do not touch the tape with your fingers. INSERTING A CASSETTE Insert the cassette in the direction as shown. Push in gently, but continuously, on the center-back of the cassette until it is drawn into the TV/VCR. The TV/VCR will automatically turn on. CORRECT Window WRONG The TV/VCR has the auto repeat function that allows you to repeat a tape indefinitely without touching the PLAY button. ALL REPEAT: Repeat playback from the beginning to the end of the tape. BLANK REPEAT: Repeat playback from the begin- ning to a blank part, which is blank for more than 10 seconds. 1 Select “USER’S SET UP” Press the MENU button on the remote control. Press the PLAY/K or STOP/L but- ton to point to “USER’S SET UP”. Then, press the F.FWD/B button. 2 Select “ALL” or “BLANK” Press the PLAY/K or STOP/L but- ton to point to “REPEAT PLAY”. Press the F.FWD/B or REW/s button repeatedly until your desired selection [ALL] or [BLANK] appears. 3 Exit the Repeat Play setting Press the MENU button on the remote control to return to the TV mode. 4 Start playback Press the PLAY button to start the Repeat Play. ”REPEAT PLAY B” appears. • Once you select the Repeat Play mode, it stays in effect even after you turn off the TV/VCR. • If the Rental mode is set [ON], the “RENTAL PLAY B” display has priority. TO CANCEL THE REPEAT PLAY MODE Repeat steps [1] and [2], select [OFF] using the F.FWD/B or REW/s button on the remote control. Press the MENU button on the remote control to return to TV mode. If there is a power failure of any kind, the unit will retain its memory for this feature. AUTO REPEAT PLAYBACK – M E N U – TIMER PROGRAMMING PICTURE CONTROL SETTING CLOCK CHANNEL SET UP B USER’S SET UP LANGUAGE [ENGLISH] ZERO RETURN TIME SEARCH – USER’S SET UP – RENTAL [OFF] B REPEAT PLAY [ALL] AUTO RETURN [OFF]

EN 9J27 PICTURE SEARCH This feature is very useful in finding or skipping over a particular scene on a tape. In this mode, the sound will be muted. 1)You may view a video tape at a high speed in either a forward or reverse direction by pressing the F.FWD or REW button. (in the SP / LP / SLP modes) 2)Press it again and the TV/VCR will now search in super high speed. (in the LP / SLP modes only) NOTE: Tapes recorded in the SP or LP mode will display a noise bar on the TV screen and the pic- ture may revert to Black and White. This is normal. 3)Press the PLAY button to return to normal speed. STILL PICTURE You can view a still picture on the TV screen during playback (the Still mode). Press the PAUSE/STILL button during playback. Only tapes recorded in the SLP mode will show the least amount of lines.Press the PLAY button to return to playback. NOTES: • Usually there will be video “noise” lines (black and white streaks or dots) on the screen. This is normal. If the tape was originally recorded in SP or LP mode, the still picture will be black and white in addition to the “noise” lines. This is not a fault of the machine, but is a by- product of the technology involved in producing a TV/VCR with 2 video heads. • If it is left in the Pause mode for more than five minutes, the TV/VCR will automatically switch to the Stop mode. SEARCH ZERO RETURN This function allows you to search easily a beginning point that you want to review by rewinding or fast forwarding. NOTE: Zero Return WILL NOT work on a blank tape or a blank portion of a tape. 1 Stop a tape at your desired point Rewind or fast forward the tape to the beginning point at which you want to review. 2 Reset the counter to 0:00:00 Press the COUNTER RESET button repeatedly. 3 Begin recording or playback Press the RECORD or PLAY button. Press the STOP button when recording or playback is completed. 4 To activate “ZERO RETURN” mode Press the MENU button on the remote control. Press the PLAY/K or STOP/L but- ton to point to “ZERO RETURN”. Then, press the F.FWD/B button. The counter will appear on the TV screen. The tape will automatically stop when the counter NOTES: • Time Search can be set up to a maximum of 9 hours 50 minutes (9:50) by 10 minutes at a time. • This function will not operate in recording mode. In the example below: To watch a program after 2 hour 50 minutes from the present position, in either direction. 1 Insert a tape. 2 Select “TIME SEARCH” mode Press the TIME SEARCH button (with each push it will increase by 10 minute). 3 Enter your desired time Press the PLAY/K or STOP/L but- ton until your desired time appears. (Example: “2:50” stands for 2 hours 50 minutes) If you wish to cancel the Time Search at this point, press the MENU button on the remote control. 4 Begin Time Search By pressing the REW/s or F.FWD/B button, the TV/VCR will rewind or fast forward to the specified point. The time counts down as the searching progresses. When 0:00 is reached, the tape will start playback automatically. TO CANCEL THE TIME SEARCH at this point Press the STOP/EJECT button on the TV/VCR or the remote control. This will delete the selected time. TIME SEARCH 2 : 50 TIME SERACH The Time Search function makes it possible to quickly advance the tape to your desired position simply by entering the exact amount of playback time you want to skip. – M E N U – TIMER PROGRAMMING PICTURE CONTROL SETTING CLOCK CHANNEL SET UP USER’S SET UP LANGUAGE [ENGLISH] B ZERO RETURN TIME SEARCH

EN 9J27 PICTURE CONTROLS TRACKING ADJUSTMENT • Tracking adjustment will be set automatically (Digital Tracking function) when you start play- back. • However when playing pre-recorded tapes or tapes recorded on units other than your own, noise lines (black and white streaks) may appear on the play- back picture. If this occurs, you can adjust the tracking control manually by pressing the CHAN- NEL K or L button until the streaks disappear. To return to the DTR function, stop the tape once and start playback again. NOISE CANCEL (in the Still mode) This feature allows you to reposition or reduce the noise lines of a still picture.Press the PAUSE/STILL button so that the noise lines change position on the screen so you can see the picture in its entirety with- out distracting noise lines. NOTE: This feature can be activated ONLY when viewing a tape recorded in the SLP mode. If the tape was originally recorded in the SP or LP mode, the still picture may revert to black and white in addition to the “noise bars”. This is normal. VERTICAL HOLD CONTROL In the Pause/Still mode only, when the picture begins to vibrate vertically, stabilize the picture by pressing the CHANNEL K or L button. NOTE: If there are video noise lines on the screen, reposition or reduce them. Refer to “NOISE CANCEL”. RENTAL PLAYBACK This function enables you to improve the picture quality when playing back worn cassettes such as rented tapes. 1 Select “USER’S SET UP” Press the MENU button on the remote control. Press the PLAY/K or STOP/L but- ton to point to “USER’S SET UP”. Then, press the F.FWD/B button. 2 Set “RENTAL” to [ON] Press the PLAY/K or STOP/L but- ton to point to “RENTAL”. Press the F.FWD/B or REW/s button until [ON] appears. 3 Exit the Rental setting Press the MENU button on the remote control to return to the TV mode. 4 Start playback Press the PLAY button to start playback. “RENTAL PLAY B” appears. • Once you select the Rental mode, it stays in effect even after you turn off the TV/VCR. TO CANCEL THE RENTAL MODE Repeat steps [1] and [2], select [OFF] using the F.FWD/B or REW/s button on the remote control. Press the MENU button on the remote control to return to TV mode. If there is a power failure of any kind, the unit will retain its memory for this feature. – USER’S SET UP – B RENTAL [ON] REPEAT PLAY [OFF] AUTO RETURN [OFF] RECORDING TWO DIFFERENT TAPE SPEEDS Before recording, select the tape speed from : SP mode (Standard Play) or SLP mode (Super Long Play). The table below shows the maximum recording/play- back time using T60, T120 or T160 tapes in each mode. Note: You can play back a tape recorded in LP mode (Long Play). Tape Speed Recording/Playback Time Type of tape T60 T120 T160 SP mode 1 hour 2 hours 2-2/3 hours SLP mode 3 hours 6 hours 8 hours ERASE PREVENTION You can prevent accidental erasing of recording by breaking off the tab on the back edge of the cassette. If you decide to record on the tape again, cover the hole with plastic tape. Tab Transparent Tape – M E N U – TIMER PROGRAMMING PICTURE CONTROL SETTING CLOCK CHANNEL SET UP B USER’S SET UP LANGUAGE [ENGLISH] ZERO RETURN TIME SEARCH

EN 9J27 Make sure ... • TV/VCR power must be turned on. • Insert a cassette tape with its erase prevention tab in place. (If necessary, rewind or fast forward the tape to the point at which you want to begin recording.) NOTE: This unit will ONLY record and view the same channel. You can ONLY watch the same TV program that is being recorded. 1 Select the channel to be recorded Press the number buttons on the remote control or the CHANNEL K or L button. Remember: If the TV/VCR is con- nected to a cable box or satellite box, the TV/VCR must be on CH3 or CH4, then the channel to be recorded must be selected on the cable box or satellite box. 2 Select the tape speed Press the SPEED button to select the desired tape speed (SP/ SLP). 3 Begin recording Press the RECORD button. 4 Stop recording Press the STOP button when recording is completed. NORMAL RECORDING Press the PAUSE/STILL button to temporarily stop recording. Press the PAUSE/STILL or RECORD button to resume record- ing. NOTES: • After five minutes, the TV/VCR will automatically switch to the Recording mode to prevent tape dam- age. SKIPPING UNWANTED SCENES DURING RECORDING CH 10 SP REC SP PAUSE SP OTR (One Touch Recording) This function enables you to set a recording length simply by pressing the REC/OTR button on the TV/VCR. Make sure ... • TV/VCR power must be turned on. • Insert a cassette tape with its erase prevention tab in place. (If necessary, rewind or fast forward the tape to the point at which you want to begin recording.) NOTES: • This function CANNOT be done from the remote control. • Recording starts immediately when the REC/OTR button is pressed. • When the REC/OTR button is pressed 18 times, the TV/VCR returns to the Normal Recording mode. • To stop the OTR operation, press the STOP button on the TV/VCR or on the remote control. • To show the remaining time, press the DISPLAY button on the remote control so that “OTR” appears on the TV screen. (It will show up momen- tarily then disappear.) • Recording stops when 0:00 is reached. • Please note that in the SLP mode maximum record- ing time, assuming the tape is started at the begin- ning, is 8 hours using T-160 (or 6 hours using T-120). • If the tape runs out before the end time, the TV/VCR will switch to the Stop mode immediate- ly, ejects the tape and turns itself off. 1 Select the channel to be recorded Press the number buttons on the remote control or the CHANNEL K or L button. Remember: If the TV/VCR is connected to a cable box or satellite box, the TV/VCR must be on CH3 or CH4, then the channel to be recorded is selected on the cable box or satellite box. 2 Select the tape speed Press the SPEED button to select the desired tape speed (SP/ SLP).

EN 9J27 Push(es) Display Recording length 1 push (normal recording) 2 pushes 0:30 30 minutes 3 pushes 1:00 60 minutes 17 pushes 8:00 480 minutes 3 Begin OTR Press the REC/OTR button on the TV/VCR as many times as needed. The recording length will be deter- mined by the number of times you press the REC/OTR button. Each additional push will increase the recording time by 30 minutes. It is set up to 8 hours. OTR(2 : 30) SP Avoid over lap of programs ... There is a chance that a program will not be record- ed. when programs overlap; • The program with an earlier start has priority. • Once the earliest program finishes, the overlapping programs will begin recording in sequence. • The illustration below demonstrates the sequence of recordings. 1 Select “TIMER PROGRAMMING” Press the MENU button on the remote control. Confirm “TIMER PROGRAM- MING” is pointed by pressing the PLAY/K button. And press the F.FWD/B button. • If you have not yet set the clock, “MANUAL CLOCK SET” appears. If so, fol- low stops [3] to [8] on page 15. Then set the timer recording. 2 Select your desired program position (1~8) Press the PLAY/K or STOP/L but- ton to select the desired program position. Then, press the F.FWD/B button. 3 Set the channel number Press the PLAY/K or STOP/L button until the desired channel number appears. (Example: CH61) Then, press the F.FWD/B button. Remember: If the TV/VCR is connected to a cable box or satellite box, the TV/VCR must be on CH3 or CH4, then the channel to be recorded is selected on the cable box or satellite box. 4 Select once, every day or weekly recording For once recording : Press the PLAY/K (up) button TIMER RECORDING 9:00AM 10:00AM 12:00PM Program 1 10:00AM-11:00AM Program 2 9:00AM-10:00AM Program 3 9:30AM-12:00PM 11:00AM Recording Sequence *Recording period is SHADED You may set the TV/VCR to start and end a record- ing while you are away. You can set 8 programs to record on specific days, daily or weekly within a 1 year period. In the example below, the timer is being set to record: DATE: July 6th, 2001 SETTING TIME: from 7:30PM to 8:50PM CHANNEL: CH61 TAPE SPEED: SP Make sure ... • If a cable box or satellite box is connected with the TV/VCR you will be limited to record only one channel. And the channel selector on the TV/VCR must be selected to the output channel of the boxes CH 3 or CH 4 and then the actual channel to be recorded must be selected on the boxes. • Clock must be set to the correct time and date before setting the timer. • TV/VCR power must be turn on to program it. • Insert a cassette tape with its erase prevention tab in place. (If necessary, rewind or fast forward the tape to the point at which you want to begin recording.) • The channel you want to record is properly set in advance. – TIMER PROGRAMMING – CH DATE BEGIN END - - -/- - - - - -:- - -:- - - - - - -/- - - - - -:- - -:- - - - - - -/- - - - - -:- - -:- - - - B - - -/- - - - - -:- - -:- - - - - - -/- - - - - -:- - -:- - - - - - -/- - - - - -:- - -:- - - - - - -/- - - - - -:- - -:- - - - - - -/- - - - - -:- - -:- - - - – TIMER PROGRAMMING – CH DATE BEGIN END - - -/- - - - - -:- - -:- - - - - - -/- - - - - -:- - -:- - - - - - -/- - - - - -:- - -:- - - - B 61 -/- - - - - -:- - -:- - - - - - -/- - - - - -:- - -:- - - - - - -/- - - - - -:- - -:- - - - - - -/- - - - - -:- - -:- - - - - - -/- - - - - -:- - -:- - - - – TIMER PROGRAMMING – CH DATE BEGIN END - - -/- - - - - -:- - -:- - - - - - -/- - - - - -:- - -:- - - - - - -/- - - - - -:- - -:- - - - B 61 EVRY DAY -:- - -:- - - - - - -/- - - - - -:- - -:- - - - - - -/- - - - - -:- - -:- - - - - - -/- - - - - -:- - -:- - - - - - -/- - - - - -:- - -:- - - - – TIMER PROGRAMMING – CH DATE BEGIN END - - -/- - - - - -:- - -:- - - - - - -/- - - - - -:- - -:- - - - - - -/- - - - - -:- - -:- - - - B 61 7/06 FRI -:- - -:- - - - - - -/- - - - - -:- - -:- - - - - - -/- - - - - -:- - -:- - - - - - -/- - - - - -:- - -:- - - - - - -/- - - - - -:- - -:- - - - – M E N U – B TIMER PROGRAMMING PICTURE CONTROL SETTING CLOCK CHANNEL SET UP USER’S SET UP LANGUAGE [ENGLISH] ZERO RETURN TIME SEARCH

EN 9J27 until the desired date appears. (Example: “7/06” for July 6th). Then, press the F.FWD/B button. For every day recording : To record a TV program at the same time on the same channel every day. (Example: Monday through Sunday) Press the STOP/L (down) button until “EVRY DAY” appears. Then, press the F.FWD/B but- ton. For weekly recording : To record a TV program at the same time on the same channel every week. (Example: every Monday) Press the STOP/L (down) button until “EVRY” and your desired day of the week appear together. Then, press the F.FWD/B button. 5 Set beginning hour Press the PLAY/K or STOP/L but- ton until the desired hour appears. (Example: “ 7, PM” for 7:30PM) Then, press the F.FWD/B button. 6 Set beginning minute Press the PLAY/K or STOP/L but- ton until the desired minute appears. (Example: “30” for 7:30PM) Then, press the F.FWD/B button. 7 Set end hour Press the PLAY/K or STOP/L but- ton until the desired hour appears. (Example: “8, PM” for 8:50PM) Then, press the F.FWD/B button. 8 Set end minute Press the PLAY/K or STOP/L but- ton until the desired minute appears. (Example: “50” for 8:50PM) Then, press the F.FWD/B button. 9 Set the tape speed Press the PLAY/K or STOP/L but- ton until the desired tape speed appears. (Example: SP) – TIMER PROGRAMMING – CH DATE BEGIN END - - -/- - - - - -:- - -:- - - - - - -/- - - - - -:- - -:- - - - - - -/- - - - - -:- - -:- - - - B 61 EVRY MON -:- - -:- - - - - - -/- - - - - -:- - -:- - - - - - -/- - - - - -:- - -:- - - - - - -/- - - - - -:- - -:- - - - - - -/- - - - - -:- - -:- - - - – TIMER PROGRAMMING – CH DATE BEGIN END - - -/- - - - - -:- - -:- - - - - - -/- - - - - -:- - -:- - - - - - -/- - - - - -:- - -:- - - - B 61 7/06 FRI 7:12PM -:- - - - - - -/- - - - - -:- - -:- - - - - - -/- - - - - -:- - -:- - - - - - -/- - - - - -:- - -:- - - - - - -/- - - - - -:- - -:- - - - – TIMER PROGRAMMING – CH DATE BEGIN END - - -/- - - - - -:- - -:- - - - - - -/- - - - - -:- - -:- - - - - - -/- - - - - -:- - -:- - - - B 61 7/06 FRI 7:30PM -:- - - - - - -/- - - - - -:- - -:- - - - - - -/- - - - - -:- - -:- - - - - - -/- - - - - -:- - -:- - - - - - -/- - - - - -:- - -:- - - - – TIMER PROGRAMMING – CH DATE BEGIN END - - -/- - - - - -:- - -:- - - - - - -/- - - - - -:- - -:- - - - - - -/- - - - - -:- - -:- - - - B 61 7/06 FRI 7:30PM 8:30PM - - - - -/- - - - - -:- - -:- - - - - - -/- - - - - -:- - -:- - - - - - -/- - - - - -:- - -:- - - - - - -/- - - - - -:- - -:- - - - – TIMER PROGRAMMING – CH DATE BEGIN END - - -/- - - - - -:- - -:- - - - - - -/- - - - - -:- - -:- - - - - - -/- - - - - -:- - -:- - - - B 61 7/06 FRI 7:30PM 8:50PM- - - - -/- - - - - -:- - -:- - - - - - -/- - - - - -:- - -:- - - - - - -/- - - - - -:- - -:- - - - - - -/- - - - - -:- - -:- - - - – TIMER PROGRAMMING – CH DATE BEGIN END - - -/- - - - - -:- - -:- - - - - - -/- - - - - -:- - -:- - - - - - -/- - - - - -:- - -:- - - - B 61 7/06 FRI 7:30PM 8:50PMSP - - -/- - - - - -:- - -:- - - - - - -/- - - - - -:- - -:- - - - - - -/- - - - - -:- - -:- - - - - - -/- - - - - -:- - -:- - - - 10 Finish setting the program Press the F.FWD/B or REW/s button. The program is now completed. • To set another program, repeat steps [2] to [10]. • Press the MENU button on the remote control to return to original mode. 11 Set the timer Press the POWER button to set automatic timer recording. The TIMER REC indicator lights up. • You must turn off the TV/VCR to activate automat- ic timer recording. If power is not turned off and you continue watch- ing TV, “TIMER REC STANDBY” starts flashing on the TV screen 2 minutes before the programmed start time. To shift the time schedule of an automatic timer recording. 1)Press the POWER button. 2)Repeat step [1] on page 21. 3)Press the RECORD button and select the desired program using the PLAY/K or STOP/L button. 4)Press the RECORD button again. Each additional push will shift forward the begin/end time for recording by 10 minutes. When the recording is already in progress, each additional push will shift forward the end time only. If you want to cancel while setting, press the PAUSE/STILL button on the remote control. The recording time returns to the original time. NOTE: When you shift forward the time schedule during recording, the recording speed will automati- cally be set to the SLP mode. 5)Press the F.FWD/B or REW/s button to exit the setting menu. Then press the MENU button on the remote control to return to original mode. TO CORRECT A PROGRAM • While setting a program; press the REW/s but- ton to go back one step and enter the correct num- bers using the PLAY/K or STOP/L button. • After setting a program; 1)Press the POWER button. 2)Repeat steps [1] - [2] on page 21. 3)Press the F.FWD/B button (or press the REW/s button to go back one step) until the part you want to correct begins flashing, then make the changes pressing the PLAY/K or STOP/L but- ton. 4)Press the POWER button to set automatic timer recording.

EN 9J27 TO CANCEL AN AUTOMATIC TIMER RECORDING • After setting a program; 1)Press the POWER button. 2)Repeat steps [1] ~ [2] on page 21 and select a program you want to cancel. 3)Press the T-PROG. CLEAR button. 4)Press the MENU button on the remote control to return to TV mode. • While recording is in progress; 1)Press POWER button. 2)Press the STOP/EJECT button on the TV/VCR. TO CHECK THE BEGIN/END TIME 1)Press the POWER button so that the REC indicator goes off. 2)Press the MENU button on the remote control. 3)Confirm “TIMER PROGRAMMING” is pointed. 4)Press the F.FWD/B button. The details of pro- grams appear on the TV screen. 5)Press the MENU button on the remote control to return to TV mode. HINTS FOR AUTOMATIC TIMER RECORDING • Make sure the channel you want to record is prop- erly set in advance. • It is not necessary to press the RECORD button for timer recording. • Recording begins automatically at the Start time. • If you are recording using a Timer mode, you may not operate the unit manually. • The erase-prevention tab on the cassette must be in place (or you must put tape over the hole). • If the erase-prevention tab is removed, the cassette will be ejected when the POWER button is pressed to off. • If the tape runs out before the end time, the TV/VCR will switch to the Stop mode immediate- ly, and the tape will be ejected. AUTO RETURN With this feature, after timer recording is finished, the beginning of the recorded program(s) can be searched for automatically. 1 Select “USER’S SET UP” Press the MENU button on the remote control. Press the PLAY/K or STOP/L but- ton to point to “USER’S SET UP”. Then, press the F.FWD/B button. 2 Set “AUTO RETURN” to [ON] Press the PLAY/K or STOP/L but- ton to point to “AUTO RETURN”. Press the F.FWD/B or REW/s button until [ON] appears. 3 Auto Return will begin When all the timer recordings are completed, the TV/VCR will rewind to the beginning of the recorded program(s). NOTE: • If you press the POWER button while tape is rewinding, the Auto Return will stop. 4 Watch the recorded program Press the PLAY button. TO CANCEL THE AUTO RETURN MODE Repeat steps [1] and [2], select [OFF] using the F.FWD/B or REW/s button. If there is a power failure of any kind, the unit will retain its memory for this feature. – USER’S SET UP – RENTAL [OFF] REPEAT PLAY [OFF] B AUTO RETURN [ON] WAKE UP TIMER The Wake Up Timer function turns on the TV/VCR without using the POWER button after a desired period of time. NOTES: • Use the remote control for this procedure. • Clock must be set to the correct time before setting the timer. • If you want to select [TAPE], you must insert a cassette tape in the TV/VCR. The tape will start playback automatically on your desired time. 1 Select “WAKE UP TIMER” Press the WAKE UP/SLEEP button on the remote control once, and confirm “ON/OFF” is pointed. Press the F.FWD/B or REW/s button until [ON] appears. 2 Select “TV” or “TAPE” Press the PLAY/K or STOP/L but- ton until to point to “TV/TAPE”. Press the F.FWD/B or REW/s button, and select [TV] or [TAPE]. WAKE UP BON/OFF [ON] TIMER TV/TAPE [TV] TIME [12:00AM] WAKE UP ON/OFF [ON] TIMER BTV/TAPE [TV] TIME [12:00AM] – M E N U – TIMER PROGRAMMING PICTURE CONTROL SETTING CLOCK CHANNEL SET UP B USER’S SET UP LANGUAGE [ENGLISH] ZERO RETURN TIME SEARCH

EN 9J27 3 Set wake up time Press the PLAY/K or STOP/L but- ton until to point to “TIME”. Press the F.FWD/B or REW/s button until your desired wake up time appears. Each additional push will increase (or decrease) the time by 10 minutes. 4 Exit the Wake Up Timer setting Press the MENU button on the remote control to return to TV mode. TO CANCEL THE WAKE UP TIMER Repeat step [1] but select [OFF]. SLEEP TIMER The Sleep Timer function turns off the TV/VCR without using the POWER button after a desired period of time. NOTE: • This function does not operate during Recording mode. 1 Select “SLEEP TIMER” Press the WAKE UP/SLEEP button on the remote control until “SLEEP TIMER” appears. 2 Set sleep time Press the PLAY/K, STOP/L, F.FWD/B or REW/s button until your desired sleep time appears. Each additional push will increase the time by 30 minutes up to 120 minutes. Press the MENU button on the remote control to exit the Sleep Timer setting. TO CANCEL THE SLEEP TIMER Press the WAKE UP/SLEEP button on the remote control until “SLEEP TIMER” appears. To view the time left for sleep timer press the WAKE UP/SLEEP button twice, then press the MENU but- ton on the remote control to exit the sleep timer set- ting. SLEEP TIMER [2:00] WAKE UP ON/OFF [ON] TIMER TV/TAPE [TV] BTIME [12:00AM] You can make copies of video tapes made by friends or relatives for your enjoyment. Connect your TV/VCR and a Source (Playing) VCR using the following diagram. WARNING: Unauthorized recordings of copyrighted video tapes may be an infringement of copyright laws. VIDEO IN OUT AUDIO AUDIO VIDEO POWER REC [Fig.8] [Ex: Source (playing) VCR or camcorder] Audio/Video adapter cable (not supplied) [The TV/VCR] COPYING A VIDEO TAPE 1)Insert a pre-recorded video cassette into the Source (Playing) VCR or camcorder. 2)Insert a blank video cassette, or one you want to record over, into the TV/VCR’s cassette compart- ment. 3)Press the SPEED button on remote control for the TV/VCR to select the desired recording speed (SP/SLP). 4)Press the CHANNEL K or L button on the TV/VCR until “AUX” appears on the screen. NOTE: “AUX” is found below the lowest memo- rized channel. (Example: CH2) 5)Press the RECORD button on the TV/VCR. 6)Begin playback of the tape in the source (Playing) VCR or camcorder. NOTE: For best results during dubbing, use the TV/VCR’s front panel controls whenever possible. The remote control might affect the source (Playing) VCR’s playback operation.

EN 9J27 CABINET CLEANING • Wipe the front panel and other exterior surfaces of the TV/VCR with a soft cloth immersed in luke- warm water and wrung dry. • Never use a solvent or alcohol. Do not spray insec- ticide liquid near the TV/VCR. Such chemicals may cause damage and discoloration to the exposed surfaces. AUTO HEAD CLEANING • Automatically cleans video heads as you insert or remove a cassette, so you can see a clear picture. • Playback picture may become blurred of interrupt- ed while the TV program reception is clear. Dirt accumulated on the video heads after long periods of use, or the usage of rental or worn tapes can cause this problem. If a streaky or snowy picture appears during play- back, the video heads in your TV/VCR may need to be cleaned. MAINTENANCE 1.Please visit your local Audio/Video store and pur- chase a good quality VHS Video Head Cleaner. 2.If a Video Head Cleaner does not solve the prob- lem, please call our help line at 1-800-256-2487, to locate an Authorized Service Center. NOTES: • Remember to read the instructions included with the video head cleaner before use. • Clean video heads only when problems occur. SERVICING • Should your TV/VCR become inoperative, do not try to correct the problem by yourself. There are no user-serviceable parts inside. Turn off, unplug the power cord, and please call our help line at 1-800- 256-2487, to locate an Authorized Service Center. ON SCREEN DISPLAY To check the Counter, Clock and Channel number on the TV screen, press the DISPLAY button on the remote control. Each time you press the DISPLAY button on the remote control, the TV screen will change as follows: • Counter mode: After 5 seconds, only the counter remains. To clear it, press the DISPLAY button. • Clock mode: After 5 seconds, only the clock and the channel number remain. To clear them, press the DIS- PLAY button. SPECIAL FEATURES REAL TIME TAPE COUNTER This shows the elapsed recording or playback time in hours, minutes, and seconds. (The displayed time will not change on a blank tape or blank portions on the tape.)The “–” indication will appear when the tape has rewound further than “0:00:00” on the tape counter. AUTO REWIND-EJECT • When the end of a tape is reached during record- ing, playback, or fast-forward, the tape will auto- matically rewind to the beginning. After rewinding finishes, the TV/VCR will eject the tape and turn itself to off. • This function is operative when Repeat Play is set to the [OFF] position. • The tape will not auto-rewind during timer record- ing or One Touch Recording. COUNT 0:12:34 5:40PM CH2 Press once Press once Press once

EN 9J27 TROUBLESHOOTING GUIDE If you have followed the instructions contained in this manual and have difficulty in operating your TV/VCR, locate the PROBLEM in the left column below. Check the corresponding CORRECTIVE ACTION column to remedy the problem. PROBLEM CORRECTIVE ACTION No power. • Make sure the AC cord is connected to an AC outlet. • Make sure the car battery cord is connected to vehicle’s cigarette lighter socket and to DC 13.2V jack on back of the TV/VCR. • Check the fuse (5A, 250V) in car battery cord. • Make sure the power is turned on. No picture and sound. • Make sure the AC cord is connected to an AC outlet. • Check antenna connection. • Let the TV/VCR program its’ tuner memory. No picture or poor picture on • Adjust direction or replace antenna. TV/VCR. • Adjust picture controls. No sound or poor sound. • Adjust volume control on remote control or main unit. • Press the MUTE button to restore sound. Timer recording is not possible. • Make sure the timer recording is set correctly. • Make sure the power is off. • Make sure the TV/VCR clock is set correctly. Cannot go into Record mode. • Make sure the tape has an erase-prevention tab. If need, cover the • hole with plastic tape. Playback picture is partially noisy. • Adjust tracking control for a better picture using the CHANNEL K • or L button on the TV/VCR. No picture but the audio is OK in • Head cleaning may be necessary. Refer to “AUTO HEAD playback. • CLEANING” on page 27. No operation by infrared Remote • Make sure the AC cord is connected to an AC outlet. Control. • Check batteries in remote control. Video or color fades in and out • You can not copy a copyrighted video tape. You are experiencing when making a copy of a video tape. • copy guard protection. Can not set the auto clock to ON. • Make sure the AC cord is connected to an AC outlet. “DEW” appears on the screen. • Refer to page 4 “WARNING”.

EN 9J27 GENERAL SPECIFICATIONS CRT : 9 inch in-line gun, 90˚ deflection tube Television system : NTSC-M Video Heads : Rotary two-head Tape width : 1/2 inch Tape speed SP : 33.40mm/sec. LP : 16.67mm/sec. SLP : 11.12mm/sec. Tuner channel TV VHF Low : #2~#6 TV VHF High : #7~#13 TV UHF : #14~#69 CATV VHF : 5A MID band : A5~A1, A~I SUPER band : J~W HYPER band : W+1~W+84 Terminals Antenna input : VHF/UHF 75 ohms unbalanced Video input : RCA connector [ 1 Audio input : RCA connector [ 1 Earphone : 1/8” monaural (3.5 mm) ELECTRICAL SPECIFICATIONS Video input level : 0.5~2.0Vp-p Audio input level : -15dBs Video S/N ratio : More than 46dB Audio S/N ratio : More than 43dB OTHER SPECIFICATIONS Power requirement : AC 120V/60Hz DC 13.2V Power consumption : AC/DC 60W Dimensions : H:13” (330mm) W:12-1/8” (308mm) D:12-15/16” (329mm) Weight : 18.7 lbs (8.5kg) • Designs and specifications are subject to change without notice and without our legal obligation. • If there is a discrepancy between languages, the default language will be English. SPECIFICATIONS CABLE CHANNEL DESIGNATIONS If you subscribe to cable TV, the channels are displayed as 1-125. Cable companies often designate channels with letters or letter-number combinations. Please check with your local cable company. The following is a chart of common cable channel designations. TV Display TV Display TV Display TV Display TV Display TV Display TV Display TV Display CATV channel TV Display W+80 W+81 W+82 W+83 W+84 W+65 W+66 W+67 W+68 W+69 W+70 W+71 W+72 W+73 W+74 W+75 W+76 W+77 W+78 W+79 W+55 W+56 W+57 W+58 A-4 A-3 A-2 A-1 W+59 W+60 W+61 W+62 W+63 W+64 W+40 W+41 W+42 W+43 W+44 W+45 W+46 W+47 W+48 W+49 W+50 W+51 W+52 W+53 W+54 W+25 W+26 W+27 W+28 W+29 W+30 W+31 W+32 W+33 W+34 W+35 W+36 W+37 W+38 W+39 W+10 W+11 W+12 W+13 W+14 W+15 W+16 W+17 W+18 W+19 W+20 W+21 W+22 W+23 W+24 A-5 R S T U V W W+1 W+2 W+3 W+4 W+5 W+6 W+7 W+8 W+9 C D E F G H I J K L M N O P Q 5A 2 3 4 5 6 7 8 9 10 11 12 13 A B 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 CATV channel CATV channel CATV channel CATV channel CATV channel CATV channel CATV channel CATV channel

ship as follows: DURATION: PARTS: FUNAI CORP. will provide parts to replace defective parts without charge for one (1) year from the date of original retail purchase. Two (2) years for Picture Tube. Certain parts are excluded from this warranty. LABOR: FUNAI CORP. will provide the labor without charge for a period of ninety (90) days from the date of original retail purchase. LIMITS AND EXCLUSIONS: This warranty is extended only to the original retail purchaser. A purchase receipt or other proof of original retail purchase will be required together with the product to obtain service under this warranty. This warranty shall not be extended to any other person or transferee. This warranty is void and of no effect if any serial numbers on the product are altered, replaced, defaced, missing or if service was attempted by an unauthorized service center. This FUNAI CORPORATION Limited warranty does not apply to any product not purchased and used in the United States. This warranty only covers failures due to defects in material or workmanship which occurs during normal use. It does not cover damage which occurs in shipment, or failures which are caused by repairs, alterations or product not supplied by FUNAI CORP., or damage which results from accident, misuse, abuse, mishandling, misapplication, alteration, faulty installation, improper maintenance, commercial use such as hotel, rental or office use of this prod- uct or damage which results from fire, flood, lightning or other acts of God. THIS WARRANTY DOES NOT COVER PACKING MATERIALS, ANY ACCESSORIES (EXCEPT REMOTE CONTROL), ANY COSMETIC PARTS, COMPLETE ASSEMBLY PARTS, DEMO OR FLOOR MODELS. FUNAI CORP. AND ITS REPRESENTATIVES OR AGENTS SHALL IN NO EVENT BE LIABLE FOR ANY GENERAL, INDIRECT OR CONSEQUENTIAL DAMAGES ARISING OUT OF OR OCCASIONED BY THE USE OF OR THE INABILITY TO USE THIS PRODUCT. THIS WARRANTY IS MADE IN LIEU OF ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, AND OF ALL OTHER LIABILITIES ON THE PART OF FUNAI, ALL OTHER WARRANTIES INCLUDING THE WARRANTY OF MERCHANTABILITY, AND FIT- NESS FOR A PARTICULAR PURPOSE, ARE HEREBY DISCLAIMED BY FUNAI AND ITS REPRESENTA- TIVES IN THE UNITED STATES. ALL WARRANTY INSPECTIONS AND REPAIRS MUST BE PERFORMED BY A FUNAI AUTHORIZED SERVICE CENTER. THIS WARRANTY IS VALID WHEN THE UNIT IS CARRIED-IN TO FUNAI AUTHO- RIZED SERVICE FACILITY. IMPORTANT: THIS LIMITED WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS, YOU MAY HAVE OTHER RIGHTS THAT VARY FROM STATE TO STATE, IF, AT ANY TIME DURING THE WARRANTY PERIOD, YOU ARE UNABLE TO OBTAIN SATISFACTION WITH THE REPAIR OF THIS PRODUCT, PLEASE CONTACT FUNAI CORP. ATTENTION: FUNAI CORP. RESERVES THE RIGHT TO MODIFY ANY DESIGN OF THIS PRODUCT WITHOUT PRIOR NOTICE. To locate your nearest FUNAI Authorized Service Center or for general service procedure, please call 1-800-256-2487 or write to the following: FUNAI CORPORATION Customer Service 100 North Street; Teterboro, NJ 07608 Tel :1-800-256-2487 PLEASE DO NOT SHIP YOUR UNIT TO THE TETERBORO ADDRESS. Printed in China 0EMN T4259UK * * * * *