Pyle PLMR20W Instruction Manual

W/ USB/SD/MP3 Playback & 3.5 Aux-In PLMR-20W CLK BAND MODE AUX SD SD/USB/MP3 PLAYER VOL + - PUSH SEL RESET LOUD PTY TA TP AF RPT RDM EON IR Specification GENERAL FM SECTION AM SECTION RCA LINE OUT MMC/SD or USB PLAYBACK Supply VoltageDC 12V Negative Ground Current Consumption Max. 7.5A Power Output 4x60 240W ( ) Number of Channels 2 STEREO channels Unit Dimensions 178(W)x108(D)x50(H)mm Frequency Range 87.5MHz 107.9MHz Effective Sensitivity 3uV. Signal to noise 50dB Frequency Range 530KHz 1710KHz Effective Sensitivity 40dB. Output 1000mV@MAX. System MP3 audio system Frequency 20Hz-20KHz Signal to Noise 55dB (1KHz) Signal to noise 40dB Characteristics (MMC/SD & USB)

1.- RESET BUTTON The unit must be reset under the following conditions: A) Prior to using this unit for the first time after installation. B) If the unit fails to operate properly, press the RESET with a pen tip or other pointed instrument. 2. - SEL & VOL CONTROL BUTTON A) Press the SEL repeatedly to select VOLUME - BASS - TREBLE - BALANCE - FADER. B) Press and hold the SEL to select EQ(JASS - ROCK - POPS - CLASS - OFF) and LOUD(ON/OFF). 3. -POWER ON/OFF AND MUTE Press the POWER to turn on this unit. To turn off the unit, press and hold this button unit it off. During playing, press this to mute the sound. 9. - CLOCK BUTTON Press the CLK to show the time. To adjust the time, press and hold the CLK until flashing and change HOUR or MINUTE by rotate the >>I or I<< button. 10-15. - PRESET STATIONS MEMORY AND >II, INT, RPT, RDM BUTTONS A) Radio mode Press the 1-6 buttons to select the preset stations. Press and hold the 1-6 buttons to store the station that currently listening. B) SD/MMC, and USB mode Press the >II to pause or resume playing. Press the INT to play the first 10 seconds of the tracks. Press again to off this function and the current track will keep playing. Press the RPT once to repeat plays the current track. Press the RPT twice to repeat plays the current folder. Press the RDM to turn random play on or off. Press the 5/6 to move up or down 10 tracks at a time (Note: when the remaining tracks less than 10, this function is invalid) WIRES CONNECTION ISO SOCKET WHITE RED RCA OUTPUT FRONT LEFT SPEAKER JACK FRONT RIGHT SPEAKER JACK RCA OUTPUT ANTENNA JACK ISO SOCKET SKETCH FUSE 7.5 A CONNECTOR B 1. VIOLET R.R SP(+) 2. VIOLET BLACK R.R SP(-) 3. GREY F.R SP(+) 4. GREY BLACK F.R SP(-) 5 7. GREEN R.L SP(+) 8. GREEN BLACK R.L SP(-) . WHITE F.L SP(+) 6. WHITE BLACK F.L SP(-) INSTALLATION METHOD METAL MOUNTING SLEEVE Bend the tabs on the metal mounting sleeve against the DASHBOARD with a screwdriver. METAL SUPPORT STARP DASHBOARD For optimum anti-skip capability of the unit, please ensure the metal support strap is bolted firmly to the car chassis. SOFT PLASTIC TRIM RING To remove the unit out of the metal mounting sleeve, insert the two supplied KEYS into the left and right side slots of the chassis at the same time. Then pull the chassis out of the metal mounting sleeve as shown in the right illustration. 16. - AUX INPUT JACK (3.5MM STEREO JACK) Press the MODE to select auxiliary input playing mode when connecting with external audio device. 17. - SD/MMC CARD SLOT When SD/MMC card is inserted, the unit is automatically switched to SD/MMC mode. (Note: if both USB storage device and SD/MMC card inserted, the system will switch to the mode of the latest connected.) 18. - USB PORT When USB storage device is connected, the unit is automatically switched to USB mode. 4. - LCD DISPLAY 5. - MODE BUTTON Press the MODE to select RADIO/CARD(SD/MMC card inserted)/USB(flash driver inserted)/AUX mode. SD/MMC, and USB mode Press and hold this button to activate TRACK SEARCH and play the select track automatically. 6&7. - TUNE,SEEK, TRACK, SKIP UP/DOWN BUTTONS A) Radio mode Press the>>I or I<< to perform manual seek tuning. Press and hold the >>I or I<< to perform automatic tuning. The unit will tune to the station with strong signal. B) SD/MMC, and USB mode Press the >>I or I<< to play the next or previous track. 8. - BAND BUTTON Press the BND to select radio band as follow: FM1 -> FM2 -> FM3 -> AM1 -> AM2 Press and hold the BND button to activate the auto storage function. The unit scans and preset the stations with strongest signal.(18stations in FM and 12 stations in AM ) CONNECTOR A 1. 2. 3. 4.YELLOW MEMORY +12V 5. BLUE AUTO ANTENNA B+ 6. 7. RED POWER B+ 8. BLACK GROUND 1 10 11 12 13 14 15 16 2 3 7 5 4 17 18 8 6 9 CLK BAND MODE AUX SD SD/USB/MP3 PLAYER VOL + - PUSH SEL RESET LOUD PTY TA TP AF RPT RDM EON IR