Pyle PDWM2800 Operation & User’s Manual
Text of the manual
GENERAL DESCRIPTION •••••••••••••••••• 2
FEATURES
••••••••••••••••
2
CAUTION
•••••••••••••••••••••••••••••• 3
ILLUSTRATION OF RECEIVER
RECEIVER REMARK· • • • • • • • • • • • • • • • • • • •• 4
USING THE RECEIVER
• • • • • • • • • • • • • • • •• 5
ILLUSTRATION OF TRANSMITTER
HANDHELD TRANSMITTER REMARK ••••••••• 5
USING THE HANDHELD TRANSMITTER •••••• 6
BODYPACKTRANSMITTER REMARK •••••••• 6
USING BODY-PACK TRANSMITTER •••••••••• 7
STANDARD PARTS ••••••••••••••••••••••• 7
REMOVE BREAKDOWN. • • • • • • • • • • • • • • • • • •• 8
PARAMETER •••••••••••••••••••••••••••••• 9
------1 ------
This wireless microphone system uses the UHF band.
It’s perfect for use on performance stages, assembly
halls, and karaoke bars.
You can use this product with lapel mics or handheld
microphones.
Please read this manual carefully for proper operation.
Read this before operating your unit:
1. Please read this manual carefully before
using. Keep it in a safe place for future
reference.
2. Do not expose the unit to rain or an
environment where it may be splashed with
water. This could result in fire or electric shock.
3. Do not force on switches, knobs, or cords.
When moving, first turn off the power.
4. Do not attempt to clean the unit with chemical
solvents; this might damage the surface. Use a
clean, dry cloth.
5. To prevent receiver damage, please turn off
power during electrical storms.
6. The voltage must be the same that is specified
on the unit.
CD Power Switch
@ Audio Volume Control
(3) RF&Audio Signal Display
B:
Q) Power Switch
@ Switchorer of R F and
Antenna indicator
@AudioSignallndicator
® Digita Tube Frequency
Display
® Antenna
® Mixed Audio Outlet&
Separate Outlet
1. Draw out the antennas and form them in a V shape.
2. Connect one end of the audio cable with the DC input jack of
the receiver and the other to the microphone input port of an
audio mixer or power amplifier.
3. Connect the AC adaptor to the DC port and then plug into the
wall.
4. Press the switch of the receiver to turn on the receiver, and
then turn on the power supply.
1. Open the handheld microphone battery cover and put in
two batteries – make sure the polarity is correct.
2. Turn on the power switch of the microphone. The power
indicator on the microphone and the RF indicator should
light on.
3. When the transmitter is not used, turn off the power.
4. When the low voltage indicator lights, replace the battery.
5. Take out the battery when not using for a long period of
time.
1. The transmitter does
not load the battery,
1. Load in a new battery
and the battery no
2. Connect receiver's
The power indicator is
power or the battery
naton
polarity is wrong.
power
2. The power jack of rece-
iver is not attached
3. Tum on the power of
power.
3 •. oower switch is off
receiver.
1. the transmitter is
1. Tum on the transmitter
noitumed on.
2. Joint the receiver and
2. the AF cord of rece-
iver has not been
ioudspeaker together.
No voice
connected.
3. Tum up the volume
3. the volume of the
receiver or the loud-
4. Do not make the
speaker is too low.
bBnsmittar far fNlSy
4. the transmitter is
far from the receiver.
from the receiver.
The distance between
1. Do not draw out the
the receiver and
antenna fully.
1. Draw out the antenna
transmitter is not far
2. The power of the
fully.
enough
battery is not
2. Replace a new battery.
enough.
1. The power of the
1. Replace a new battery.
battery is not enough.
2. Put the loudspeaker
The voice is distortion
2. The loud speaker is
far from the receiver.
too near to the
receiver.
------8------
Audio Frequency Response:
System Distortion:
Audio Output Level:
Power supply:
Current Consumption:
TRANSMITTER
Maximum Deviation Range:
Frequency Stability:
RF Output Power:
RF Rejection:
Current Consumption:
Operate Range:
Battery:
480-S60Mhz
<2UV (12dB SINAD)
>80dB
>80dB
>60dB
80-12S00HZ
<1%
700mV(600D)
DC12V-17V/600MA
< 400mA
SO KHz (Max)
±O.OOS%
<40mW
>40dB
<100mA
60-80M
1.SVX2 AA
------9------
