Sylvania DVR90DG Owner's Manual

Antenna in jack (commercially available) ANTENNA AUDIO IN VIDEO IN L R AUDIO OUT VIDEO OUT (L1) IN IN OUT OUT S-VIDEO COMPONENT VIDEO OUTPUT L Y PB/CB PR/CR R (Back of This Unit) Audio/Video cables (supplied) RF cable RF cable (supplied) Antenna Cable TV signal 3 4 6 5 2 1 Set channel 3 or 4. Turn on your TV and select channel 3 or 4. Note • The quality of picture may become poor if this unit is connected to an RF modulator. Recording Playing discs Editing Before you start Connections Getting started Changing the Setup menu Others Español Please read before using this equipment. If you need additional operating assistance after reading this owner’s manual or to order replacement accessories, please call TOLL FREE : 1-800-605-8453 or visit our web site at http://www.SylvaniaConsumerElectronics.com INSTRUCCIONES EN ESPAÑOL INCLUIDAS Owner’s Manual REC/OTR REC SPEED OPEN/CLOSE CHANNEL REV FWD STOP PLAY POWER S-VIDEO VIDEO AUDIO L R DVR90DG Connection to a TV (Before you use this unit, you need to complete connections.) If your TV has AUDIO/VIDEO input jacks, see the section “Connections” on pages 13–15. If not, it is still possible to connect this unit to your TV by using a Stereo Audio/Video RF modulator. In this case, follow the instructions below. 1) The antenna input jack of your TV may have been already occupied. If so, disconnect the RF cable from your TV, and then connect the RF cable to the ANTENNA IN jack of this unit. 2) Connect the ANTENNA OUT jack of this unit to your RF modulator (usually marked “ANT IN”) by the RF cable. 3) Connect your RF modulator to your TV by another RF cable. 4) Connect the AUDIO/VIDEO output jacks of this unit to the AUDIO/VIDEO input jacks of your RF modulator by Audio/Video cables. 5) Set your RF modulator’s channel 3/4 switch to either 3 or 4, whichever the TV channel is least used in your area. If your RF modulator has a Modulator/Antenna switch, set it according to your RF modulator’s manual. 6) Turn on your TV and choose the same channel as you set the RF modulator’s channel 3/4 switch to. For more details, follow the instructions supplied with the RF modulator. DVD Recorder To record a program easily, refer to “Easy DVD recording” on pages 16-17 after con- nections are completed. (You CANNOT record on any copyright protected DVD disc with this unit.)

device, due to possible eye injury. CAUTION: USE OF CONTROLS OR ADJUSTMENTS OR PERFORMANCE OF PROCEDURES OTHER THAN THOSE SPECIFIED HEREIN MAY RESULT IN HAZARDOUS RADIATION EXPOSURE. CAUTION: VISIBLE AND INVISIBLE LASER RADIATION WHEN OPEN AND INTERLOCK DEFEATED. DO NOT STARE INTO BEAM. LOCATION: INSIDE, NEAR THE DECK MECHANISM. TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated “dan- gerous voltage” within the product’s enclosure that may be of sufficient magnitude to consti- tute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and mainte- nance (servicing) instructions in the literature accompanying the appliance. CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN RADIO-TV INTERFERENCE This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residen- tial installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: 1) Reorient or relocate the receiving antenna. 2) Increase the separation between the equipment and receiver. 3) Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. 4) Consult the dealer or an experienced radio/TV technician for help. This Class B digital apparatus complies with Canadian ICES-003. Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada. FCC WARNING- This equipment may generate or use radio frequency energy. Changes or modi- fications to this equipment may cause harmful interference unless the modifications are expressly approved in the manual. The user could lose the authority to operate this equipment if an unauthor- ized change or modification is made. CAUTION: TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE SLOT, FULLY INSERT. ATTENTION:POUR ÉVITER LES CHOC ÉLECTRIQUES, INTRODUIRE LA LAME LA PLUS LARGE DE LA FICHE DANS LA BORNE CORRESPONDANTE DE LA PRISE ET POUSSER JUSQU’AU FOND. A NOTE ABOUT RECYCLING This product’s packaging materials are recyclable and can be reused. Please dispose of any materials in accordance with your local recycling regulations. Batteries should never be thrown away or incinerated but disposed of in accordance with your local regulations concerning chemi- cal wastes. For Customer Use: Read carefully the information located at the back of this unit and enter below the Model No. and Serial No. Retain this information for future reference. Model No. _____________________ Serial No. _____________________ Make your contribution to the environment!!! • Used up batteries do not belong in the dust bin. • You can dispose of them at a collection point for used up batteries or special waste. Contact your council for details. Before you start WARNING:

Connections Getting started Changing the Setup menu Others Español Precautions (cont’d) IMPORTANT SAFEGUARDS 1. Read Instructions - All the safety and operating instructions should be read before the appliance is operated. 2. Retain Instructions- The safety and operating instructions should be retained for future reference. 3. Heed Warnings - All warnings on the appliance and in the operating instructions should be adhered to. 4. Follow Instructions - All operating and use instructions should be followed. 5. Cleaning - Unplug this product from the wall outlet before cleaning. Do not use liquid cleaners or aerosol cleaners. Use a damp cloth for cleaning. EXCEPTION: A product that is meant for uninterrupted service and, that for some specific reason, such as the possibility of the loss of an authorization code for a CATV converter, is not intended to be unplugged by the user for cleaning or any other purpose, may exclude the reference to unplugging the appliance in the cleaning description otherwise required in item 5. 6. Attachments - Do not use attachments not recommended by the product manufacturer as they may cause hazards. 7. Water and Moisture- Do not use this product near water, for example, near a bath tub, wash bowl, kitchen sink, or laundry tub, in a wet basement, or near a swimming pool, and the like. 8. Accessories - Do not place this product on an unstable cart, stand, tripod, bracket, or table. The product may fall, causing serious injury to a child or adult, and serious damage to the appliance. Use only with a cart, stand, tripod, bracket, or table recommended by the manufacturer, or sold with the product. Any mounting of the appliance should follow the manufacturer's instructions and should use a mounting accessory recommended by the manufacturer. An appliance and cart combination should be moved with care. Quick stops, excessive force, and uneven surfaces may cause the appliance and cart combination to overturn. 9. Ventilation - Slots and openings in the cabinet are provided for ventilation and to ensure reliable operation of the product and to protect it from overheating, and these openings must not be blocked or covered. The openings should never be blocked by placing the product on a bed, sofa, rug, or other similar surface. This product should not be placed in a built-in installation such as a bookcase or rack unless proper ventilation is provided or the manufacturer's instructions have been adhered to. 10. Power Sources - This product should be operated only from the type of power source indicated on the marking label. If you are not sure of the type of power supply to your home, consult your appliance dealer or local power company. For products intended to operate from battery power, or other sources, refer to the operating instructions. 11. Grounding or Polarization - This product is equipped with a polarized alternating-current line plug (a plug having one blade wider than the other). This plug will fit into the power outlet only one way. This is a safety feature. If you are unable to insert the plug fully into the outlet, try reversing the plug. If the plug should still fail to fit, contact your electrician to replace your obsolete outlet. Do not defeat the safety purpose of the polarized plug. 12. Power Cord Protection - Power supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against them, paying particular attention to cords at plugs, convenience receptacles, and the point where they exit from the appliance. 13. Outdoor Antenna Grounding - If an outside antenna or cable system is connected to the product, be sure the antenna or cable system is grounded so as to provide some protection against voltage surges and built-up static charges. Article 810 of the National Electrical Code, ANSI/ NFPA No. 70, provides information with regard to proper grounding of the mast and supporting structure, grounding of the lead-in wire to an antenna discharge unit, size of grounding conductors, location of antenna-discharge unit, connection to grounding electrodes, and requirements for the grounding electrode. (Fig. A) 14. Lightning - For added protection for this product during a lightning storm, or when it is left unattended and unused for long periods of time, unplug it from the wall outlet and disconnect the antenna or cable system. This will prevent damage to the product due to lightning and power-line surges. 15. Power Lines - An outside antenna system should not be located in the vicinity of overhead power lines or other electric light or power circuits, or where it can fall into such power lines or circuits. When installing an outside antenna system, extreme care should be taken to keep from touching such power lines or circuits as contact with them might be fatal. 16. Overloading - Do not overload wall outlets and extension cords as this can result in a risk of fire or electric shock. 17. Object and Liquid Entry - Never push objects of any kind into this product through any openings as they may touch dangerous voltage points or short-out parts that could result in a fire or electric shock. Never spill liquid of any kind on the product. 18. Servicing - Do not attempt to service this product yourself as opening or removing covers may expose you to dangerous voltage or other hazards. Refer all servicing to qualified service personnel. 19. Damage Requiring Service - Unplug this product from the wall outlet and refer servicing to qualified service personnel under the following conditions: a. When the power-supply cord or plug is damaged, b. If liquid has been spilled, or objects have fallen into the product, c. If the product has been exposed to rain or water, d. If the product does not operate normally by following the operating instructions. Adjust only those controls that are covered by the operating instructions as an improper adjustment of other controls may result in damage and will often require extensive work by a qualified technician to restore the product to its normal operation, e. If the product has been dropped or damaged in any way, and f. When the product exhibits a distinct change in performance this indicates a need for service. 20. Replacement Parts - When replacement parts are required, be sure the service technician has used replacement parts specified by the manufacturer or have the same characteristics as the original part. Unauthorized substitutions may result in fire, electric shock or other hazards. 21. Safety Check - Upon completion of any service or repairs to this product, ask the service technician to perform safety checks to determine that the product is in proper operating condition. 22. Heat - This product should be situated away from heat sources such as radiators, heat registers, stoves, or other products (including amplifiers) that produce heat. FIGURE A EXAMPLE OF ANTENNA GROUNDING AS PER NATIONAL ELECTRICAL CODE ANTENNA LEAD WIRE ANTENNA DISCHARGE UNIT (NEC SECTION 810-20) GROUNDING CONDUCTORS (NEC SECTION 810-21) GROUND CLAMP GROUND CLAMP ELECTRIC SERVICE EQUIPMENT POWER SERVICE GROUNDING ELECTRODE SYSTEM (NEC ART 250, PART H) NEC – NATIONAL ELECTRICAL CODE S2898A Before you start

About Copyright Unauthorized copying, broadcasting, public performance and lending of discs are prohibited. This product incorporates copyright protection technology that is protected by U.S. patents and other intellectual property rights. Use of this copyright protection technology must be authorized by Macrovision, and is intended for home and other limited viewing uses only unless otherwise authorized by Macrovision. Reverse engineering or disassembly is prohibited. Moisture Condensation Warning Moisture condensation may occur inside the unit when it is moved from a cold place to a warm place or after heating a cold room or under conditions of high humidity. Do not use this unit at least for 2 hours until its inside gets dry. Notice for progressive scan output Consumers should note that not all high definition television sets are fully compatible with this product and may cause artifacts to be displayed in the picture. In case of picture problems with 525 progressive scan output, it is recommended that the user switch the connection to the ‘standard definition’ output. If there are questions regarding your TV set compatibility with this 525p DVD recorder, please contact our customer service center. Installation Location For safety and optimum performance of this unit: • Install the unit in a horizontal and stable position. Do not place anything directly on top of the unit. Do not place the unit directly on top of the TV. • Shield it from direct sunlight and keep it away from sources of intense heat. Avoid dusty or humid places. Avoid places with insufficient ventilation for proper heat dissipation. Do not block the ventilation holes on the sides of the unit. Avoid locations subject to strong vibration or strong magnetic fields. Avoid the Hazards of Electrical Shock and Fire • Do not handle the power cord with wet hands. • Do not pull on the power cord when disconnecting it from AC wall outlet. Grasp it by the plug. • If, by accident, water is spilled on this unit, unplug the power cord immediately and take the unit to our Authorized Service Center for servicing. • Remote control (NB075UD) with two AA batteries • RF cable (WPZ0901CAB01 or WPZ0901TM002) • Audio/Video cables (WPZ0102TM015 or WPZ0102LTE01) • Owner’s Manual (1VMN21672) • Quick Use Guide (1VMN21673) Owner's Manual Supplied Accessory

Recording Playing discs Editing Before you start Connections Getting started Changing the Setup menu Others Español Manufactured under license from Dolby Laboratories. “Dolby” and the double-D symbol are trademarks of Dolby Laboratories. SERVICING • Please refer to relevant topics on “Troubleshooting” on pages 72-75 before returning the product. • If this unit becomes inoperative, do not try to correct the problem by yourself. There are no user- serviceable parts inside. Turn off, unplug the power plug and please call our help line mentioned on the front page to locate an Authorized Service Center. CLEANING THE CABINET • Use a soft cloth slightly moistened with a mild detergent solution. Do not use a solution containing alcohol, spirits, ammonia or abrasive. CLEANING DISCS • When a disc becomes dirty, clean it with a cleaning cloth. Wipe the disc from the center to out. Do not wipe in a circular motion. • Do not use solvents such as benzine, thinner, commercially available cleaners, detergent, abrasive cleaning agents or antistatic spray intended for analogue records. CLEANING THE DISC LENS • If this unit still does not perform properly although you refer to the relevant sections and to “Troubleshooting” in this Owner’s Manual, the laser optical pickup unit may be dirty. Consult your dealer or an Authorized Service Center for inspection and cleaning of the laser optical pickup unit. DISC HANDLING • Handle the discs so that fingerprints and dust do not adhere to the surfaces of the discs. • Always store the disc in its protective case when it is not used. Maintenance Dolby Digital Recording “Dolby® Digital Recording enables consumers to record high-quality video with stereo sound on recordable DVD discs. The technology, when utilized instead of PCM recording, also saves record- able disc space, allowing for higher video resolution or extended recording time on each DVD. DVDs created using Dolby Digital Recording will play back on all DVD-Video players.” Note: This is true when the players are compatible with actual recordable DVD discs.

Before you start Fast forward / Fast reverse . . . . . . . . . . . . . . . . . 41 Skipping TV commercials during play . . . . . . . . . 41 Rapid Play . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42 Step by step playback . . . . . . . . . . . . . . . . . . . . . 42 Slow forward / Slow reverse play . . . . . . . . . . . . 42 Zoom . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43 Marker Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43 Search . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44 Title/Chapter search . . . . . . . . . . . . . . . . . . . . . . . 44 Track search . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45 Time search . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45 Repeat/Random/Program playback . . . . . . . . . . . 46 Repeat play . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46 Random playback . . . . . . . . . . . . . . . . . . . . . . . . 46 Program play . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47 Selecting the format of audio and video . . . . . . . 47 Switching subtitles . . . . . . . . . . . . . . . . . . . . . . . . 47 Switching audio soundtrack . . . . . . . . . . . . . . . . . 48 Switching virtual surround system . . . . . . . . . . . . 48 Switching camera angles . . . . . . . . . . . . . . . . . . . 49 Reducing block noise . . . . . . . . . . . . . . . . . . . . . . 49 Editing . . . . . . . . . . . . . . . . . . . . . . . . . . 50 Information on disc editing . . . . . . . . . . . . . . . . . 50 Guide to a title list . . . . . . . . . . . . . . . . . . . . . . . . 50 Editing discs in Video mode . . . . . . . . . . . . . . . . . 50 Editing discs in VR mode . . . . . . . . . . . . . . . . . . . 50 Editing discs in Video mode . . . . . . . . . . . . . . . . 51 Deleting titles . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51 Putting names on titles . . . . . . . . . . . . . . . . . . . . 52 Setting or clearing chapter markers . . . . . . . . . . . 53 Editing discs in VR mode (Original) . . . . . . . . . . 54 Deleting titles . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54 Setting titles to protect . . . . . . . . . . . . . . . . . . . . . 55 Releasing titles from protecting . . . . . . . . . . . . . . 56 Editing discs in VR mode (Playlist) . . . . . . . . . . . 57 Deleting titles . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57 Dividing a title . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58 Combining titles . . . . . . . . . . . . . . . . . . . . . . . . . . 59 Adding titles to a Playlist . . . . . . . . . . . . . . . . . . . 60 Deleting a Playlist . . . . . . . . . . . . . . . . . . . . . . . . 60 Editing discs in VR mode (Original / Playlist) . . 61 Deleting parts of titles . . . . . . . . . . . . . . . . . . . . . 61 Putting names on titles . . . . . . . . . . . . . . . . . . . . 62 Setting or clearing chapter markers . . . . . . . . . . . 63 Setting pictures for thumbnails . . . . . . . . . . . . . . 64 Changing the Setup menu . . . . . . . . . . 65 Tour of the Setup menu . . . . . . . . . . . . . . . . . . . . 65 Language setting . . . . . . . . . . . . . . . . . . . . . . . . . . 66 Display setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67 Audio setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68 Settings for Parental lock level . . . . . . . . . . . . . . 70 Others . . . . . . . . . . . . . . . . . . . . . . . . . . . 72 Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . 72 Language code . . . . . . . . . . . . . . . . . . . . . . . . . . . 75 Glossary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76 Frequently Asked Questions . . . . . . . . . . . . . . . . 76 Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77 Español . . . . . . . . . . . . . . . . . . . . . . . . . . 78 Before you start . . . . . . . . . . . . . . . . . . . . 2 Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Table of contents . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Symbol in this Owner’s Manual . . . . . . . . . . . . . . . 7 Functional overview . . . . . . . . . . . . . . . . . . . . . . . . 8 Installing batteries in the remote control . . . . . . . 10 Using a remote control . . . . . . . . . . . . . . . . . . . . . 10 Display menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 Setup menus . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 Connections . . . . . . . . . . . . . . . . . . . . . . 13 Connection to a TV . . . . . . . . . . . . . . . . . . . . . . . . 13 Connection to a cable box or satellite box . . . . . 14 Connection to an Audio System . . . . . . . . . . . . . 15 Getting started . . . . . . . . . . . . . . . . . . . . 16 Easy DVD recording . . . . . . . . . . . . . . . . . . . . . . . 16 Initial setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 Channel setting . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 Getting channels automatically . . . . . . . . . . . . . . 18 Adding/deleting channels . . . . . . . . . . . . . . . . . . . 19 Selecting the TV stereo or SAP . . . . . . . . . . . . . . 20 Setting the clock . . . . . . . . . . . . . . . . . . . . . . . . . . 21 Auto Clock Setting . . . . . . . . . . . . . . . . . . . . . . . . 21 Manual Clock Setting . . . . . . . . . . . . . . . . . . . . . . 22 Setting the Daylight Saving Time . . . . . . . . . . . . . 23 Selecting the TV aspect ratio . . . . . . . . . . . . . . . . 23 Recording . . . . . . . . . . . . . . . . . . . . . . . . 24 Information on DVD recording . . . . . . . . . . . . . . . 24 Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24 Recordable disc . . . . . . . . . . . . . . . . . . . . . . . . . . 24 Recording speed . . . . . . . . . . . . . . . . . . . . . . . . . 24 Restrictions on recording . . . . . . . . . . . . . . . . . . . 25 Information on copy control . . . . . . . . . . . . . . . . . 25 Making discs playable in other DVD player (Finalize) . . 25 Formatting a disc . . . . . . . . . . . . . . . . . . . . . . . . . 26 Choosing the recording format of a blank disc . . 26 Reformatting a disc . . . . . . . . . . . . . . . . . . . . . . . 27 Setting for Auto Chapter . . . . . . . . . . . . . . . . . . . 27 Basic recording . . . . . . . . . . . . . . . . . . . . . . . . . . . 28 One-touch Timer Recording . . . . . . . . . . . . . . . . . 29 Timer Recording . . . . . . . . . . . . . . . . . . . . . . . . . . 30 Hints for Timer Recording . . . . . . . . . . . . . . . . . . 32 Settings for an external source . . . . . . . . . . . . . . 33 Connection to an external source . . . . . . . . . . . . 33 Recording from an external source . . . . . . . . . . . 34 Setting a disc to protect . . . . . . . . . . . . . . . . . . . . 34 Finalizing the discs . . . . . . . . . . . . . . . . . . . . . . . . 35 Auto finalize . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36 Playing discs . . . . . . . . . . . . . . . . . . . . . 37 Information on DVD play . . . . . . . . . . . . . . . . . . . 37 Guide to displays . . . . . . . . . . . . . . . . . . . . . . . . . 37 Basic playback . . . . . . . . . . . . . . . . . . . . . . . . . . . 38 Playback . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38 Playing MP3 disc . . . . . . . . . . . . . . . . . . . . . . . . . 39 Playing discs using the Disc menu . . . . . . . . . . . 40 Playing discs using the Title menu . . . . . . . . . . . 40 Pause . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40 Special playback . . . . . . . . . . . . . . . . . . . . . . . . . . 41 Resume play . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41

Recording Playing discs Editing Before you start Connections Getting started Changing the Setup menu Others Español Recording This unit is compatible with both DVD-RW, which is rewritable repeatedly and DVD-R, which is available for recording once. You can choose either one for your convenience. Up to 8 program recording: You can program the unit to record up to 8 programs, with in a month in advance. Daily or weekly program recordings are also available. One-touch Timer Recording: You can easily set a recording time as you prefer. Every time [REC/OTR] is pressed during recording, the recording time will be increased by 30 minutes up to 8 hours. The recording automatically stops when the recording time you set is reached. Automatic Chapter marker setting: Chapter markers will be put on recordings as you set in the Setup menu before attempting to record. Automatic Title menu making: The unit makes title menus automatically when final- izing the disc which are recorded in Video mode. Automatic Playlist making (VR mode): A Playlist will be prepared from an Original title, so that you can edit titles in a Playlist as you prefer. An Original title is kept as it is. Automatic finalizing (Video mode): You can finalize discs after finishing all Timer Recordings and at the end of the disc space auto- matically as you set in the Setup menu. Left channel stereo recording: This unit can record the sound of the Left channel monaural input as Left and Right channels automati- cally (the input from the LINE 2 only). Play Theater surround sound in your home: When connecting the unit to an amplifier or a decoder which is compatible with Dolby Digital, you are allowed to experience the theater surround sound from discs with surround sound system. Quick search for what you want to watch: You can easily find the part you want to watch using the search function. Search for a desired point on a disc by title, chapter or time. Start to play from Original and Playlist: Title playing is available from either an Original title or Playlist. Virtual Surround System: You can enjoy stereophonic space through your excit- ing 2 channel stereo system. Playing back on MP3 disc: You can enjoy MP3 files which are recorded on CD-R/RW. Editing Deleting titles: You can delete titles which you do not need anymore. Making your own Playlist: With the original remains as it is, you can edit titles on various Playlist as you prefer. Putting names on titles Setting pictures for thumbnails Setting / clearing chapter markers Dividing / combining titles Deleting parts of titles, etc. Protecting titles: To avoid editing or erasing titles, the protect function is useful when it is ON in the Original titles. Compatibility Available for playing discs recorded in Video mode on a regular DVD player (Video mode): Discs recorded in Video mode can be played on regular DVD players, including computer DVD drives compatible with DVD-Video playback*. You will need to finalize the discs recorded in Video mode to play in other DVD players. * DVD-Video Format (Video mode) is a new format for recording on DVD-RW/R discs that was approved by the DVD Forum in 2000. Adoption of this format is optional for manufactures of DVD playback devices and there are DVD-Video players, DVD-ROM drives or other DVD playback devices that do not play DVD- RW/R discs recorded in the DVD-Video Format. Others Progressive Scan system Unlike conventional interlace scanning, the progressive scan system provides less flickering and images in higher resolution than that of traditional television signals. This DVD unit not only plays DVDs and CDs but also offers features for you to record to DVD discs and edit them after that. The following features are offered with this unit. Symbol in this Owner’s Manual Many functions of this unit are depending on the disc type or the recording mode. To specify for what disc type or recording mode each function is, we put the following symbols at the beginning of each item to operate. Features Symbol Description Available to DVD-Video discs Available to DVD-RW in Video mode Available to DVD-RW in VR mode Available to DVD-R discs Available to Audio CDs Available to CD-RW/R discs with MP3 files DVD-V DVD-V DVD-RW DVD-RW Video DVD-R DVD-R CD CD MP3 MP3 DVD-RW DVD-RW VR

Front Panel 1. Disc tray Place a disc when open. 2. Display Refer to “Front Panel Display Guide” on page 12. 3. OPEN/CLOSE A button* Press to open or close the disc tray. 4. CHANNEL L / K button Press to change the channel up and down. 5. REV E button During playback, press to skip to the previous chap- ter or track. During playback, press and hold for 1.5 seconds to fast reverse. When playback is paused, press repeatedly to slow reverse. 6. FWD D button During playback, press to skip to the next chapter or track. During playback, press and hold for 1.5 seconds to fast forward. When playback is paused, press repeatedly to slow forward. 7. STOP C button Press to stop play or recording. 8. PLAY B button* Press to start or resume play. 9. POWER button Press to turn the unit on and off. If timer programmings have been set, press to set the unit in timer-standby mode. 10. AUDIO input jacks (LINE2) Use to connect external equipment with standard audio cable. 11. VIDEO input jack (LINE2) Use to connect external equipment with a standard video cable. 12. S-VIDEO input jack (LINE2) Use to connect the S-Video output of external equipment with an S-Video cable. 13. REC/OTR button Press once to start a recording. Press repeatedly to start a One-touch Timer Recording. 14. REC SPEED button Press to switch the recording speed. 15. Remote control sensor Receive signals from your remote control so that you can control the unit from a distance. Rear Panel ANTENNA AUDIO IN VIDEO IN L R AUDIO OUT VIDEO OUT (L1) IN IN OUT OUT S-VIDEO COMPONENT VIDEO OUTPUT L Y PB/CB PR/CR R DIGITAL AUDIO OUTPUT PCM / BITSTREAM COAXIAL 1 2 3 4 5 6 7 8 9 10 11 1. ANTENNA IN jack Use to connect an antenna. 2. VIDEO IN jack (LINE1) Use to connect external equipment with a standard video cable. 3. VIDEO OUT jack Use to connect a TV monitor, AV receiver or other equipment with a standard video cable. 4. AC Power Cord Connect to a standard AC outlet to supply power to this unit. 5. COAXIAL DIGITAL AUDIO OUTPUT jack Use to connect an AV receiver, Dolby Digital decod- er or other equipment with a coaxial digital input jack with a digital coaxial cable. 6. AUDIO OUT jacks Use to connect a TV monitor, AV receiver or other equipment with standard audio cable. 7. COMPONENT VIDEO OUTPUT jacks Use to connect a TV monitor with component video inputs with component video cables. 8. S-VIDEO OUT jack Use to connect the S-Video input of a TV monitor, AV receiver or other equipment with an S-Video cable. 9. S-VIDEO IN jack (LINE1) Use to connect the S-Video output of external equipment with an S-Video cable. 10. AUDIO IN jacks (LINE1) Use to connect external equipment with standard audio cable. 11. ANTENNA OUT jack Use to connect an antenna cable to pass the signal from the TV ANTENNA IN to your TV monitor. Note • Do not touch the inner pins of the jacks on the rear panel. Electrostatic discharge may cause permanent damage to the unit. • This unit does not have the RF modulator. REC/OTR REC SPEED OPEN/CLOSE CHANNEL REV FWD STOP PLAY POWER S-VIDEO VIDEO AUDIO L R 8*9 1211 10 13 14 15 1 2 3* 4 5 6 7 (*) The unit can also be turned on by pressing these buttons.

Press to open or close the disc tray. 14. TIMER PROG. button Press to display the Timer Programming list. 15. CH K / L buttons Press to change the channel up and down. 16. REPEAT button Press to display the Repeat menu. 17. SETUP button Press to display the Setup menu. During DVD playback, press and hold for more than 5 sec- onds to switch the progressive scanning mode to the interlace mode. 18. CLEAR button Press to clear the password once entered or to cancel the programming for CD or to clear the selecting marker number in the marker setup mode or to clear the program once entered in the Timer Recording setting mode, etc. 19. ENTER button Press to confirm or select menu items. 21. PLAY B button* Press to start or resume play. 22. FWD D button During playback, press to play fast forward. Or when playback is paused, press to play slow forward. 23. PAUSE F button Press to pause play or record- ing. 24. CM SKIP button During playback, press to skip 30 seconds. 25. STOP C button Press to stop play or recording. POWER ZOOM DISPLAY SETUP TOP MENU MENU/LIST REC SPEED REC/OTR PAUSE SKIP SKIP PLAY CM SKIP REPEAT OPEN/CLOSE TIMER PROG. FWD REV CLEAR 1 2 3 4 5 6 7 8 9 SPACE 0 A H G ENTER CH RETURN .@/: ABC DEF GHI JKL MNO PQRS TUV WXYZ B C { B K L h g F STOP Bx1.3/0.8 9 1 13* 15 17 18 16 20 22 21* 24 23 25 14 3 4 5 11 12 10 2 6 7 8 19 (*) The unit can also be turned on by pressing these buttons. Functional overview (cont’d) Before you start Recording Playing discs Editing Before you start Connections Getting started Changing the Setup menu Others Español Remote Control 20. RETURN button Press to return to the previ- ously displayed menu screen. 1. POWER button Press to turn the unit on and off. If timer programmings have been set, press to set the unit in timer-standby mode. 2. ZOOM button During playback, press to enlarge the picture on the screen. 3. Number buttons Press to select channel numbers. Press to select a title/chapter/ track on display. Or press to enter values for the settings in the Setup menu. 4. DISPLAY button Press to display the On Screen menu on or off. 5. TOP MENU button Press to display the Top menu. 6. MENU/LIST button Press to display the Disc menu. To change Original and Playlist on the TV screen. (VR mode only) 7. Cursor K / L / { / B buttons Press to select items or settings. 8. REV E button During playback, press to fast reverse. Or when playback is paused, press to play slow reverse. 9. REC SPEED button Press to switch the recording speed. 10. B x1.3/0.8 button During playback, press to play- back in a slightly faster/slower speed with keeping the audio quality. 11. REC/OTR button Press once to start a record- ing. Press repeatedly to start a One-Touch Timer Recording. 12. SKIP H button During playback, press to skip to the previous chapter or track. Or when playback is paused, press to play reverse step by step. SKIP G button During playback, press to skip to the next chapter or track. Or when playback is paused, press to play forward step by step.

Before you start Press [DISPLAY] to call up the Display menu. This menu will give you the information on the playing disc. Some operations are available while disc is playing. 1. Indicates a disc type and a format mode. NOTE: In some descriptions on this manual, only one disc type is indicated as an example. 2. Indicates a channel number. 3. Indicates a recording mode and possible recording time left. 4. Indicates a title number, chapter number and the time lapse of disc play. 5. Each icon means: 6. Indicates current disc status. Using a remote control Keep in mind the following when using the remote control: • Make sure that there is no obstacle between the remote control and the remote sensor on the unit. • Remote operation may become unreliable if strong sunlight or fluorescent light is shining on the remote sensor of the unit. • Remote control for different devices can interfere with each other. Avoid using remote control for other equipment located close to the unit. • Replace the batteries when you notice a fall off in the operating range of the remote control. • The maximum operable ranges from the unit are as follows. - Line of sight: approx. 23 feet (7m) - Either side of the center: approx. 16 feet (5m) within 30° - Above: approx. 16 feet (5m) within 15° - Below: approx. 10 feet (3m) within 30° Installing batteries in the remote control Install two “AA” size batteries (supplied) matching the polarity indicated inside battery compartment of the remote control. Note: Incorrect use of batteries can result in hazards such as leakage and bursting. Please observe the following: • Do not mix new and old batteries together. • Do not use different kinds of batteries together, although they may look similar, different batteries may have different voltages. • Make sure that the plus and minus ends of each battery match the indications in the battery compartment. • Remove batteries from equipment that is not going to be used for a month or more. • When disposing of used batteries, please comply with governmental regulations or environmental public instruction’s rules that apply in your country or area. • Do not recharge, short-circuit, heat, burn or disassemble batteries. REC/OTR REC SPEED OPEN/CLOSE CHANNEL REV FWD STOP PLAY POWER S-VIDEO VIDEO AUDIO L R POWER DISPLAY REC SPEED CLEAR CM SKIP SKIP REC PAUSE P ENTER REC MONITOR OPEN/CLOSE TIMER PROG. MENU PLAY LIST TOP MENU/ ORIGINAL SPACE 1 2 3 4 5 6 7 8 9 0 FWD STOP PLAY REV CH .@/: ABC DEF GHI JKL MNO PQRS TUV WXYZ Remote control 30° Within about 23 feet (7m) 30° 2 1 3 Guide to Displays the On Screen menu This unit uses the following the On Screen menu for most operations: Setup menu, Title list, Playlist, Original and Display menu. They allow you to change the playing status of disc during play. The Display menu also gives you information on the status of the disc. : Search : Audio : Subtitle : Angle (except VR mode) : Repeat : Marker : Noise Reduction : Zoom : Surround DVD-R 1 1 0:00:00 XP 1:01 CH 8 Video mode 1 4 5 2 5 2 3 6 3 Display menu

Before you start Recording Playing discs Editing Before you start Connections Getting started Changing the Setup menu Others Español Setup menus Press [SETUP] to display the Setup menu, then press [ENTER] to display each menu, using [K / L]. These menus provide entries to all main functions of the unit. 1. Required Setting: To set up the required setting. 2. Playback: To set up the unit to play discs as you prefer. 3. Display: To set up the OSD screen and the front panel display of the unit as you prefer. 4. Recording: To set up the unit to record to discs as you prefer. 5. Clock: To set up the clock of the unit as you need. 6. Channel: To adjust the channel setting of the unit as you prefer. 7. Disc / CD Playback Mode: “Disc” is available only when a DVD-RW/R disc is inserted into the unit. When a DVD- Video disc (commercially available), a new DVD-R disc is inserted into the unit, you cannot select “Disc”. “CD Playback Mode” is available only when an Audio CD disc or a CD-RW/R disc with MP3 files is inserted into the unit. 1. Format (DVD-RW only): Allows you to erase all of the recorded content on the disc. The disc will be completely blank. • Erased content cannot be called back. • A DVD-RW disc formatted with this unit cannot be used in other DVD recorders without any recording using this unit. • If you want to use a disc only formatted with this unit on another DVD recorder, you have to re-format the disc on that recorder. 2. Finalize: Allows you to finalize a disc containing recorded titles. 3. Disc Protect (VR mode only): Allows you to protect a disc from accidental editing or recording. 4. Random Play: To activate the random playback feature. 5. Program Play (Audio CD only): To activate the programmed playback feature. Disc Finalize Disc Protect OFF ON Format 2 3 1 2 3 Setup Playback Display Recording Clock Channel Disc Required Setting 1 2 3 4 5 6 7 1 2 3 4 5 6 7 CD Playback Mode Program Play Random Play 4 5 4 5 Disc Finalize Format 1 2 1 2

Before you start Front Panel Display Guide Display message Appears when data is being recorded on a disc. 1 6 3 7 5 2 4 Appears when the disc tray is opening. Appears when the unit is turned on. Appears when the unit is turned off. Appears when the disc tray is closing. Appears when a disc is loaded on the disc tray. 1. Current Status of the unit :Appears when disc playback is paused. :Appears when playing a disc. :Appears when the timer programming has been set and is proceeding. Flashes when all Timer Recordings have been finished, or when a program cannot be performed by some reason. :Appears during recording process. :Appears during repeat play. 2. Disc type :Appears when an Audio CD or a disc with MP3 files is inserted in the disc tray. :Appears when a DVD disc is inserted in the disc tray. :Appears when a DVD-R disc is inserted in the disc tray. :Appears when a DVD- RW disc is inserted in the disc tray. 3. Recording speed Indicates the recording speed of the disc. 4. Title / Track and Chapter mark :Appears when indicating a title/track number. :Appears when indicating a chapter number. 5. Displays the following • Playing time • Current title / chapter / track number • Recording time/ remaining time • Clock • Channel number • OTR (One-touch Timer Recording) remaining time 6. :Appears in the afternoon with the clock displaying. 7. :Appears when the progressive scan system is activated.

Connections Recording Playing discs Editing Before you start Connections Getting started Changing the Setup menu Others Español Make one of the following connections, depending on the capabilities of your existing equipment. ANTENNA AUDIO IN VIDEO IN L R AUDIO OUT VIDEO OUT (L1) IN IN OUT OUT S-VIDEO COMPONENT VIDEO OUTPUT L Y PB/CB PR/CR R COAXIAL R L AUDIO OUT VIDEO OUT L R S-VIDEO IN IN OUT S-VIDEO PB/CB Y PR/CR COMPONENT VIDEO IN COMPONENT VIDEO OUTPUT Y PB/CB PR/CR AUDIO OUT TV Basic Audio Method 1 Method 2 Better picture Best picture S-VIDEO OUT COMPONENT VIDEO OUT Audio cable (supplied) S-Video cable (commercially available) Component Video cable (commercially available) This unit ANTENNA AUDIO IN VIDEO IN L R AUDIO OUT VIDEO OUT (L1) IN IN OUT OUT S-VIDEO COMPONENT VIDEO OUTPUT L Y PB/CB PR/CR R DIGITAL AUDIO OUTPUT PCM / BITSTREAM COAXIAL AUDIO IN VIDEO RF cable (supplied) Video cable (supplied) Audio cable (supplied) (Back of TV) or Cable TV signal or Cable TV signal Connect Connect Connect Connect Disconnect Antenna Antenna (Back of this unit) (Back of TV) 3 2 1 4 5 Plug in the AC power cord of this unit. 6 Note • Connect this unit directly to the TV. If the A/V cables are connected to a VCR, pictures may be distorted due to the copy protection system. • When Progressive Scan mode is selected, no video signal will be output from the VIDEO OUT or S-VIDEO OUT jack. After you have completed connections • Switch the input selector on your TV to an appropriate external input channel (usually near channel 0). Press a button on the TV’s original remote control (refer to “Input Mode Names for Common TV Brands” on page15) that selects an external input channel until the DVD recorder’s picture appears. Check your TV owner’s manual for details. Video - Progressive Activating progressive scan: Check TV has progressive scan and use component video cable. NOTE: If there is no picture or picture is distorted after selecting Yes, Wait about 15 seconds for auto recovery. Activate? Yes No ON Video - Progressive OFF This unit is compatible with the Progressive Scan System. The feature provides you with the higher definition images than the traditional output system does. To utilize this feature, you must set Progressive Scan mode to “ON” in the Setup menu by following the steps below. 1. Press [SETUP] to call up the Setup menu. 2. Select “Playback” using [K / L], then press [ENTER]. 3. Select “Video” using [K / L], then press [ENTER]. 4. Select “Progressive” using [K / L], then press [ENTER]. 5. Select “ON” using [K / L], then press [ENTER]. 6. Select “Yes” using [s / B], then press [ENTER]. If your TV is compatible with Progressive Scan (525p / 480p), you must use the Component Video cable (commercially available) to connect this unit to the TV. (See Method 2 on this page.) Make sure the “P.SCAN” appears on the front panel display. If not, use the video cable and set the Progressive Scan mode to “OFF”, or press and hold [SETUP] for more than 5 seconds, so that the “P.SCAN” on the front panel display disappears.

Connections Note to the Cable TV System Installer : This reminder is provided to call the Cable TV system installer’s attention to Article 820-40 of the National Electrical Code, which provides guidelines for proper grounding - in particular, specifying that the cable ground shall be connected to the grounding system of the building, as close to the point of cable entry as possible. With this setup: • You can record any unscrambled channel by selecting the channel on the cable box or satellite box. Be sure that the cable box or satellite box is turned on. • You cannot record one channel while watching another channel. ANTENNA AUDIO IN VIDEO IN L R AUDIO OUT VIDEO OUT (L1) IN IN OUT OUT S-VIDEO COMPONENT VIDEO OUTPUT L Y PB/CB PR/CR R DIGITAL AUDIO OUTPUT PCM / BITSTREAM COAXIAL AUDIO IN VIDEO RF cable (supplied) Video cable (supplied) Audio cable (supplied) (Back of TV) Cable TV signal Connect Connect Connect Connect (Back of this unit) 2 1 3 4 IN OUT (Cable box or Satellite box) RF cable

Connections Recording Playing discs Editing Before you start Connections Getting started Changing the Setup menu Others Español • When you change the connections, all devices should be turned off. • Refer to the operation manual accompanying external devices for more information. AUDIO OUT VIDEO OUT L R Stereo system COAXIAL DIGITAL AUDIO OUTPUT PCM / BITSTREAM COAXIAL AUDIO Method 1 Analog audio input jacks Digital audio input jack AUDIO OUT DIGITAL AUDIO OUT Method 2 Audio cable (supplied) Audio Coaxial Digital cable (commercially available) Dolby Digital decoder, MD deck or DAT deck This unit Note • The audio source on a disc in a Dolby Digital Multi-channel surround format cannot be recorded as digital sound by an MD or DAT deck. • By hooking this unit up to a Multi-channel Dolby Digital decoder, you can enjoy high-quality Dolby Digital Multi- channel surround sound as heard in the movie theaters. • Playing a DVD using incorrect settings may generate noise distortion and may also damage the speakers. If output is Dolby Digital encoded audio, connect to a Dolby Digital decoder. Unless connected to a Dolby Digital decoder. Connecting to an MD deck or DAT deck. - - - STREAM PCM PCM Setup >Playback >Audio >Digital Out > PCM Dolby Digital Setting Connection * To complete these settings, refer to pages 68-69. Admiral Curtis Mathis GE Hitachi JVC Kenwood LXI-Series Magnavox AUX LINE1, LINE2, 00, 90, 91, 92, 93 INPUT, TV/VCR, 00, 90, 91, 92, 93 INPUT, AUX VIDEO, VIDEO1, VIDEO2, VIDEO3 AUX 00 AUX CHANNEL Input Mode Names for Common TV Brands Panasonic RCA Samsung Sanyo Sharp Sony Toshiba Zenith TV/VIDEO INPUT, TV/VCR, 00, 90, 91, 92, 93 TV/VIDEO VIDEO 00 VIDEO1, VIDEO2, VIDEO3 TV/GAME 00 Note • Playing a DVD using incorrect settings may generate noise distortion and may also damage the speakers.

Getting started The following will help you to understand easily how to record to DVD discs. Note: Make sure batteries are in the remote control and you have connected this unit and the TV correctly. Step 1: Choose a disc type. There are several types of recordable DVD discs to choose from. Choose a recordable DVD disc type based on your playing/recording/editing require- ments. See “DVD disc types” at the bottom of this page for more information on the differences between the different kinds of compatible media. This unit can record on the following type of discs. For example, when you want to record repeat- edly on the same disc, or when you want to edit the disc after recording, select the rewrita- ble DVD-RW type disc. When you want to save recordings without any alteration, a non-rewritable DVD-R can be your choice. Step 2: Insert a blank disc. POWER ZOOM DISPLAY SETUP TOP MENU MENU/LIST REC SPEED REC/OTR PAUSE SKIP SKIP PLAY CM SKIP REPEAT OPEN/CLOSE TIMER PROG. FWD REV CLEAR 1 2 3 4 5 6 7 8 9 SPACE 0 A H G ENTER CH RETURN .@/: ABC DEF GHI JKL MNO PQRS TUV WXYZ B C { B K L h g F STOP Bx1.3/0.8 POWER ZOOM DISPLAY SETUP TOP MENU MENU/LIST REC SPEED REC/OTR PAUSE SKIP SKIP PLAY CM SKIP REPEAT OPEN/CLOSE TIMER PROG. FWD REV CLEAR 1 2 3 4 5 6 7 8 9 SPACE 0 A H G ENTER CH RETURN .@/: ABC DEF GHI JKL MNO PQRS TUV WXYZ B C { B K L h g F STOP Bx1.3/0.8 Remote Control To open To close Format the disc Insert the disc in the recorder. Then, format the disc from the Setup menu. Video format (Video mode) or Video recording format (VR mode) will be available depending on the disc type inserted. This is necessary to pre- pare the disc for record- ing. Details are on pages 26-27. * When you format, the entire contents on that disc will be erased. * The unit automatically starts formatting when an unused DVD-RW disc is inserted. DVD disc types DVD-RW VR DVD-RW Video You want to Record TV programs Reuse by deleting unwanted contents Edit recorded contents Edit/Record from connected equipment Copy discs for distribution Play on other DVD equipment *1 *1 DVD-RW VR DVD-RW Video Features Recording Rewritable? Yes Yes Can create chapters at fixed intervals (auto.) Yes Yes Can create chapters wherever you like (manual) Yes No Can record 16:9 size pictures Yes Yes Can record Copy-Once programs Yes No Editing Can perform basic edit functions Yes Yes Can perform advanced edit functions (Playlist edit) Yes No No Yes No Yes No Yes No *1 DVD-RW (VR mode) can only be played on DVD equipment that is VR compatible. Note: For details of the above functions and implied restrictions, see the explanations inside the manual. DVD-R DVD-R : Most suitable : Can be used : Some functions are limited : Cannot be used 2 To turn on 4 Loading This operation may take a while to be recognized. 3 (or) 1

Getting started Recording Playing discs Editing Before you start Connections Getting started Changing the Setup menu Others Español Step 3: Select the recording speed. POWER ZOOM DISPLAY SETUP TOP MENU MENU/LIST REC SPEED REC/OTR PAUSE SKIP SKIP PLAY CM SKIP REPEAT OPEN/CLOSE TIMER PROG. FWD REV CLEAR 1 2 3 4 5 6 7 8 9 SPACE 0 A H G ENTER CH RETURN .@/: ABC DEF GHI JKL MNO PQRS TUV WXYZ B C { B K L h g F STOP Bx1.3/0.8 Step 5: Record on DVD disc. Step 4: Select the desired channel. POWER ZOOM DISPLAY SETUP TOP MENU MENU/LIST REC SPEED REC/OTR PAUSE SKIP SKIP PLAY CM SKIP REPEAT OPEN/CLOSE TIMER PROG. FWD REV CLEAR 1 2 3 4 5 6 7 8 9 SPACE 0 A H G ENTER CH RETURN .@/: ABC DEF GHI JKL MNO PQRS TUV WXYZ B C { B K L h g F STOP Bx1.3/0.8 XP 0:58 Step 6: Stop the recording. POWER ZOOM DISPLAY SETUP TOP MENU MENU/LIST REC SPEED REC/OTR PAUSE SKIP SKIP PLAY CM SKIP REPEAT OPEN/CLOSE TIMER PROG. FWD REV CLEAR 1 2 3 4 5 6 7 8 9 SPACE 0 A H G ENTER CH RETURN .@/: ABC DEF GHI JKL MNO PQRS TUV WXYZ B C { B K L h g F STOP Bx1.3/0.8 CH 12 I Wait for a moment. 90% Hint 1: Play the recorded contents You can select the title you want to play from a displayed menu, and immediately start to play. Recorded contents are easily accessible, with simple procedure of choosing a title on a chapter in the menu screen. What are titles and chapters? The contents of DVD disc are generally divided into titles. Titles may be further divided into chapters. Hint 2: Edit the recorded disc You will find editing discs is easy. This unit offers convenient edit functions which are possible only with DVD-RW/R discs. You can edit the following from a title list. • Putting names on titles • Setting pictures for thumbnails • Setting / clearing chapter markers • Deleting titles or scenes (Possible editing functions depend on the recording format and editing method.) Original and Playlist (VR mode) You can edit the recordings in Playlist without changing the original recordings. Playlist does not take up much disc space. What “Original” or “Playlist” is for? Throughout this manual, you will find Original and Playlist to refer to the actual content and the edited version. • Original content refers to what’s actually recorded on the disc. • Playlist content refers to the edited version of the disc; how the Original content is to be played. Finalizing a Disc • This will allow a disc that is recorded on this unit to be played back on a different DVD player — without finalization it will not be playable on another player. • After finalizing a disc if the recording was in Video mode, you cannot edit any information that is on that disc. • If you have recorded in VR mode on DVD-RW disc then editing is still permitted after finalizing. Track 1 Track 2 Track 3 Track 4 Track 5 Start Rec. Stop/Start Stop Rec. Start Rec. Stop Rec. Title 1 Title 2 Chapter 1 Chapter 1 Chapter 2 Chapter 3 Chapter 2 This operation may take a while to be completed. C POWER ZOOM DISPLAY SETUP TOP MENU MENU/LIST REC SPEED REC/OTR PAUSE SKIP SKIP PLAY CM SKIP REPEAT OPEN/CLOSE TIMER PROG. FWD REV CLEAR 1 2 3 4 5 6 7 8 9 SPACE 0 A H G ENTER CH RETURN .@/: ABC DEF GHI JKL MNO PQRS TUV WXYZ B C { B K L h g F STOP Bx1.3/0.8

• The selection will depend on how you receive the TV channels. Press [RETURN ] or [SETUP] to cancel the auto presetting during scanning. Initial setting Turn on this unit for the first time, you need to follow these steps. 1 Press [POWER]. 2 Turn the TV on. Select the input to which the unit is connected. Refer to the table on page 15. “Initial Setting” will automatically appear. 3 Using [K / L], select your desired language for the OSD. Then press [ENTER] to go to next step. 4 Press [ENTER] to Channel Preset. The unit will start getting channels available in your area. 5 After finished channel setting, “Clock Setting” will appear. Then press [ENTER]. 6 Follow to step 3 on page 22 to “Manual Clock Setting”. Channel setting 2 Using [K / L], select “Channel”. Press [ENTER]. Channel menu will appear. 3 Using [K / L], select “Auto Preset”. Press [ENTER]. The unit will start getting channels available in your area. 4 Press [SETUP] to exit. • You can select only the channels memorized in this unit by using [CHANNEL K / L] or [CH K / L]. To select a channel You can select a channel by directly entering channel using the Number buttons on the remote control. Notes for using the Number buttons: • When selecting cable channels which are higher than 99, enter channel numbers as a three-digit number. (For example: 117, press [1], [1], [7]) • You must precede single-digit channel numbers with a zero (For example: 02, 03, 04 and so on). • You can select the line input mode (“L1” or “L2”). To select “L1” by pressing [0], [0], [1]. To select “L2” by pressing [0], [0], [2]. Details are on pages 33-34. 1 2 3 4 POWER ZOOM DISPLAY SETUP TOP MENU MENU/LIST REC SPEED REC/OTR PAUSE SKIP SKIP PLAY CM SKIP REPEAT OPEN/CLOSE TIMER PROG. FWD REV CLEAR 1 2 3 4 5 6 7 8 9 SPACE 0 A H G ENTER CH RETURN .@/: ABC DEF GHI JKL MNO PQRS TUV WXYZ B C { B K L h g F STOP Bx1.3/0.8 POWER ZOOM DISPLAY SETUP TOP MENU MENU/LIST REC SPEED REC/OTR PAUSE SKIP SKIP PLAY CM SKIP REPEAT OPEN/CLOSE TIMER PROG. FWD REV CLEAR 1 2 3 4 5 6 7 8 9 SPACE 0 A H G ENTER CH RETURN .@/: ABC DEF GHI JKL MNO PQRS TUV WXYZ B C { B K L h g F STOP Bx1.3/0.8 1 Auto Presetting Now CH 1 If you have changed antenna connection, we recommend you to program available channels in your area with the following procedures. Getting channels automatically 1 Press [SETUP]. 3 4 Initial Setting Français Español English Initial Setting Clock Setting 5 Setup Playback Display Recording Clock Channel Disc Required Setting

Getting started Recording Playing discs Editing Before you start Connections Getting started Changing the Setup menu Others Español 4 Select the channel number to add or delete. Press [{] or [CH L] to move to a lower channel number. Press [B] or [CH K] to move to a higher channel number. Press the Number buttons to select a channel number directly. • [CH K / L] works on the memorized channel in this unit. • [{ / B] works on all of channel numbers. 5 Using [K / L], select “Add” or “Delete”. Press [ENTER]. The channel number will be added or deleted from the channel memory. Then the next channel number will appear so that you can continue adding or deleting channels. 6 Press [SETUP] to exit. Adding/deleting channels The channels you no longer receive or seldom watch can be deleted from the memory. You also may add channels into memory. 1 Press [SETUP]. 2 Using [K / L], select “Channel”. Press [ENTER]. Channel menu will appear. 3 Using [K / L], select “Manual Preset”. Press [ENTER]. Manual Preset menu will appear. Manual Preset CH 2 Add Delete POWER ZOOM DISPLAY SETUP TOP MENU MENU/LIST REC SPEED REC/OTR PAUSE SKIP SKIP PLAY CM SKIP REPEAT OPEN/CLOSE TIMER PROG. FWD REV CLEAR 1 2 3 4 5 6 7 8 9 SPACE 0 A H G ENTER CH RETURN .@/: ABC DEF GHI JKL MNO PQRS TUV WXYZ B C { B K L h g F STOP Bx1.3/0.8 1 2 3 4 5 6 4 Manual Preset CH 7 Add Delete

Getting started You can select a sound channel to output from TV. “Stereo” has been selected as the default. 1 Press [SETUP]. 2 Using [K / L], select “Required Setting”. Press [ENTER]. Required Setting menu will appear. 3 Using [K / L], select “TV Audio Select”. Press [ENTER]. Option window will appear. 4 Using [K / L], select “Stereo” or “SAP”. Press [ENTER]. Stereo: Outputs main audio. SAP (Secondary Audio Program): Outputs sub audio. 5 Press [SETUP] to exit. POWER ZOOM DISPLAY SETUP TOP MENU MENU/LIST REC SPEED REC/OTR PAUSE SKIP SKIP PLAY CM SKIP REPEAT OPEN/CLOSE TIMER PROG. FWD REV CLEAR 1 2 3 4 5 6 7 8 9 SPACE 0 A H G ENTER CH RETURN .@/: ABC DEF GHI JKL MNO PQRS TUV WXYZ B C { B K L h g F STOP Bx1.3/0.8 1 2 3 4 5 Notes on TV channel audio • When you record a TV program available in second audio or stereo on a DVD-RW/R, you have to select either Stereo or SAP in the Channel Preset screen beforehand. Refer to the following table to check an appropriate setting. • You can only play the disc in second audio if a TV program is available in second audio and you set “ TV Audio Select ” to “ SAP ”. TV Audio Select SAP Stereo Selected audio Broadcast audio Disc recording Audio output Stereo STEREO+SAP STEREO STEREO STEREO STEREO STEREO MONO+SAP MONO MONO MONO MONO MONO SAP STEREO+SAP SAP SAP STEREO STEREO STEREO MONO+SAP SAP SAP MONO MONO MONO Select Video TV Aspect TV Audio Select Required Setting 4:3 Letter Box Stereo

Getting started Recording Playing discs Editing Before you start Connections Getting started Changing the Setup menu Others Español Set the clock before you try the Timer Recording. If a Public Broadcasting Station (PBS) is available in your area, follow “Auto Clock Setting” below. If not, follow “Manual Clock Setting” on page 22. Auto Clock Setting Make sure • The antenna/Cable TV connections are correct. • If this unit is connected to a Cable Box or Satellite Box, select the local PBS station on them to set the clock automatically. 1 Press [SETUP]. 2 Using [K / L], select “Clock”. Press [ENTER]. Clock menu will appear. 3 Using [K / L], select “Auto Clock Setting”. Press [ENTER]. Option window will appear. 4 • If you do not know your PBS channel number: Using [K / L], select “Auto”. Press [ENTER]. The setting will be activated. • If you know your PBS channel number: Using [K / L], select “Manual”. Press [ENTER]. Using the Number buttons or [K / L], enter your PBS channel number. Press [ENTER]. The setting will be activated. • If you want to set the clock manually and cancel the Auto Clock Setting function: Using [K / L], select “OFF”. Press [ENTER]. The Auto Clock Setting function will be canceled. 5 Press [SETUP] to exit. 6 Press [POWER] to turn off the unit. This unit will search for the time only when the power is off. Leave it off for several minutes to give this unit time to set the clock on the front display panel. Note • The clock may set itself automatically after you connect the antenna/cable signal to this unit and plug in the power cord. In this case, the current time will appear on the front panel display. • If the current time is not displayed or the displayed clock is not correct, set the clock manually. POWER ZOOM DISPLAY SETUP TOP MENU MENU/LIST REC SPEED REC/OTR PAUSE SKIP SKIP PLAY CM SKIP REPEAT OPEN/CLOSE TIMER PROG. FWD REV CLEAR 1 2 3 4 5 6 7 8 9 SPACE 0 A H G ENTER CH RETURN .@/: ABC DEF GHI JKL MNO PQRS TUV WXYZ B C { B K L h g F STOP Bx1.3/0.8 2 3 4 6 1 5 Auto Clock Setting OFF Manual Auto Auto Clock Setting - Manual CH 1 Set Channel No.

1 Press [SETUP]. 2 Using [K / L], select “Clock”. Press [ENTER]. 3 Using [K / L], select “Clock Setting”. Press [ENTER]. Clock Setting menu will appear. Clock Setting ---- / -- / ---- ( ---- ) -- : ---- Press [ENTER] again. Default date will appear. 4 Using [K / L], enter the date (month / day / year). Press [{ / B] to move the cursor. Clock Setting JAN/ 01 / 2006(SUN) 12: 00 AM 5 Using [K / L], enter the time (hour / minute). Press [{ / B]. A cursor will move on AM or PM. Clock Setting JAN/ 01 / 2006(SUN) 12: 00 AM 6 Press [K / L] to select “AM” or “PM”. Press [ENTER]. Clock menu will appear, then the settings will be activated. Although seconds are not dis- played, they begin counting from zero. 7 Press [SETUP] to exit. Note • Your clock setting will be lost if either there is a power failure or this unit has been unplugged for more than 30 seconds when you set the clock manually. POWER ZOOM DISPLAY SETUP TOP MENU MENU/LIST REC SPEED REC/OTR PAUSE SKIP SKIP PLAY CM SKIP REPEAT OPEN/CLOSE TIMER PROG. FWD REV CLEAR 1 2 3 4 5 6 7 8 9 SPACE 0 A H G ENTER CH RETURN .@/: ABC DEF GHI JKL MNO PQRS TUV WXYZ B C { B K L h g F STOP Bx1.3/0.8 1 2 3 4 5 7 Setting the clock (cont’d) 6

Connections Getting started Changing the Setup menu Others Español Getting started Setting the clock (cont’d) 3 Using [K / L], select “Daylight Saving Time”. Press [ENTER]. Option window will appear. 4 Using [K / L], select “ON” or “OFF”. Press [ENTER]. Choose “ON” when currently observing the daylight saving time. 5 Press [SETUP] to exit. You can select the TV aspect ratio to match the formats of what you are playing with the unit and your TV screen (4:3 standard or 16:9 widescreen TV). “4:3 Letter Box” has been selected as the default. 1 Press [SETUP]. 2 Using [K / L], select “Required Setting”. Press [ENTER]. Required Setting menu will appear. 3 Using [K / L], select “TV Aspect”. Press [ENTER]. Option window will appear. Refer to the Note on this page. 4 Using [K / L], select a desired option. Press [ENTER]. 5 Press [SETUP] to exit. Note If you have a standard TV: Select “4:3 Letter Box”, so that black bars appear on the top and bottom of the screen. Select “4:3 Pan & Scan” for a full height picture with both sides trimmed. If you have a widescreen TV: Select “16:9 Wide”. POWER ZOOM DISPLAY SETUP TOP MENU MENU/LIST REC SPEED REC/OTR PAUSE SKIP SKIP PLAY CM SKIP REPEAT OPEN/CLOSE TIMER PROG. FWD REV CLEAR 1 2 3 4 5 6 7 8 9 SPACE 0 A H G ENTER CH RETURN .@/: ABC DEF GHI JKL MNO PQRS TUV WXYZ B C { B K L h g F STOP Bx1.3/0.8 1 2 3 4 5 POWER ZOOM DISPLAY SETUP TOP MENU MENU/LIST REC SPEED REC/OTR PAUSE SKIP SKIP PLAY CM SKIP REPEAT OPEN/CLOSE TIMER PROG. FWD REV CLEAR 1 2 3 4 5 6 7 8 9 SPACE 0 A H G ENTER CH RETURN .@/: ABC DEF GHI JKL MNO PQRS TUV WXYZ B C { B K L h g F STOP Bx1.3/0.8 1 3 4 5 2 Selecting the TV aspect ratio Setting the Daylight Saving Time When “Daylight Saving Time” is “ON”, the unit clock will automati- cally move forward one hour at 2:00a.m. on the first Sunday in April and move back one hour at 2:00a.m. on the last Sunday in October. 1 Press [SETUP]. 2 Using [K / L], select “Clock”. Press [ENTER]. Clock menu will appear. TV Aspect 4:3 Pan & Scan 16:9 Wide 4:3 Letter Box Daylight Saving Time OFF ON

DVD-R discs can only be recorded once, and cannot be erased. DVD-RW discs can be recorded and erased many times. DVD-R discs can only be recorded in Video mode, while DVD-RW discs can select a recording format between Video mode and VR mode. Recordable disc • Discs that should or should not be used with this recorder: DVD-R 8x can be used, 16x may result in a Rec error. DVD-RW 4x can be used, 6x may result in a Rec error. • Discs that have been tested and are proven to be compatible with this recorder: MITSUBISHI KAGAKU MEDIA DVD-R 8x MITSUBISHI KAGAKU MEDIA DVD-RW 2x • About Video mode and VR (Video Recording) mode Video mode is the same recording format as DVD-Video discs purchased locally, so that you can play in most DVD players. To play in other DVD players, you will need to finalize (see page 35). Unless finalized, you can play, record additionally or edit discs recorded in Video mode with this unit. VR (Video Recording) mode is a basic recording format for DVD-RW. You can record and edit repeatedly. Recording speed You can select a recording speed among 6 options, and the recording time will depend on the recording speed you select as follows. * Discs recorded in SLP or SEP on this recorder may not be played back on other DVD recorders or DVD players. • The recording time are estimates and actual recording time may differ. • The audio and video quality is getting poorer as the Recording time becomes longer. • Each time [REC SPEED] is pressed, allowed recording time will be displayed. Note • This recorder cannot record CD-RW or CD-R discs. • DVD-RW/R and CD-RW/R discs recorded on a personal computer or a DVD or CD recorder may not play if the disc is damaged or dirty or if there is dirt of condensation on the player’s lens. • If you record a disc using a personal computer, even if it is recorded in a compatible format, there are cases in which it may not play because of the settings of the application software used to create the disc. (Check with the software publisher for more detailed information.) • Discs recorded in Video mode on this unit cannot record additionally using other DVD recorders. • A DVD-RW disc formatted with this unit cannot be used in other DVD recorders without any recording using this unit. • Since the recording is made by the variable bit rate (VBR) method, depending on the picture you are recording, the actual remaining time for recording may be a little shorter than the remaining time displayed on the OSD. Recording speed XP (1H) SP (2H) LP (4H) EP (6H) SLP (8H) SEP (10H) Recording time 18 min 36 min 72 min 108 min 144 min 180 min Video/Sound Quality Disc Size 8cm Disc XP (1H) SP (2H) LP (4H) EP (6H) SLP (8H) SEP (10H) 60 min 120 min 240 min 360 min 480 min 600 min 12cm Disc (poor) (poor) (good) (good) Disc type Disc format Video mode VR mode Video mode Functions Playing, limited recording, limited editing Playing, recording, Original/Playlist editing Playing, limited recording, limited editing DVD-RW DVD-R DVD-RW DVD-RW Video DVD-RW DVD-RW VR DVD-R DVD-R Logo Attributes 8cm/12cm, single-sided, single layer disc Approx. max. recording time (SEP mode): 600 minutes (4.7GB) (for 12cm) 180 minutes (1.4GB) (for 8cm) DVD-RW DVD-R DVD players with are capable of playing DVD-RW recorded in VR mode. Information on DVD recording

Connections Getting started Changing the Setup menu Others Español Restrictions on recording You cannot record copy-protected video using this unit. Copy-protected video includes DVD-Video discs and some satellite broadcasts. If copy-protected material is encountered during a recording, recording will pause or stop automatically and an error message will be displayed on the screen. Video that is “copy-once only” can only be recorded using a DVD-RW disc in VR mode with CPRM (see below). When recording a TV broadcast or through an external input, you can display copy control information on the screen. Information on copy control Some satellite broadcasts include copy-protected information. For recording these, refer to the following. Making discs playable in other DVD player (Finalize) After recording, you must finalize the disc in order to play on other units. (Refer to page 35.) After finalizing: • Once DVD-RW/R (Video mode) is finalized, you cannot record additionally or edit. • Even if DVD-RW (VR mode) is finalized, you can record additionally or edit the disc. • When DVD-RW/R (Video mode) is finalized, the Title menu will be created automatically. To play in other DVD players, finalize discs recorded on this unit. What is “CPRM”? CPRM is a copy protection system with scramble system regarding the recording of “copy-once” broadcast programs. CPRM stands for Content Protection for Recordable Media. This unit is CPRM compatible, which means that you can record copy-once broadcast programs, but you cannot then make a copy of those recordings. CPRM recordings can only be made on DVD-RW discs formatted in VR mode, and CPRM recordings can only be played on DVD players that are specifically compatible with CPRM. Disc type / format Copy -free Copy -once Copy- prohibited Recordable Not Recordable ver.1.1,1.2 ver.1.1,1.2 CPRM compatible ver.1.1,1.2 ver.1.1,1.2 CPRM compatible ver.2.0 DVD-RW DVD-RW VR DVD-RW DVD-RW Video DVD-R DVD-R This Unit DVD player Not Playable Playable REC/OTR REC SPEED OPEN/CLOSE CHANNEL REV FWD STOP PLAY POWER S-VIDEO VIDEO AUDIO L R Information on DVD recording (cont’d)

DVD-RW DVD-RW Video DVD-RW DVD-RW VR When inserting a blank disc, the unit automatically starts to initialize the blank disc. You have to select your desired format before insert- ing the blank disc. 1 Press [SETUP]. 2 Using [K / L], select “Disc”. Press [ENTER]. Disc menu will appear. 3 Using [K / L], select “Format”. Press [ENTER]. Format menu will appear. 4 Using [K / L], select “Format Mode”. Press [ENTER]. “Video mode” has been selected as the default. 5 Using [K / L], select “Video mode” or “VR mode”. Press [ENTER]. The recording format will be set. 6 Press [SETUP] to exit. 7 Insert a blank disc. Formatting will start. 8 Formatting is complete. “100%” will be indicated. Note • The recording format setting is effective only for DVD-RW discs. You cannot change the recording format on a DVD-R disc. DVD-R discs will always be in Video mode. • You cannot mix two formats on one DVD-RW disc. When you load a disc once recorded before, the recording format cannot be changed even if you change it in the Setup menu. • When inserting a blank DVD+R or DVD+RW disc, the error message (“Disc Error”) will appear. This unit is not compatible with a DVD+RW/ R disc. • Playlist will be created automatically when recording on DVD-RW in VR mode. • A blank chapter may be created depending on the remaining time of the disc. POWER ZOOM DISPLAY SETUP TOP MENU MENU/LIST REC SPEED REC/OTR PAUSE SKIP SKIP PLAY CM SKIP REPEAT OPEN/CLOSE TIMER PROG. FWD REV CLEAR 1 2 3 4 5 6 7 8 9 SPACE 0 A H G ENTER CH RETURN .@/: ABC DEF GHI JKL MNO PQRS TUV WXYZ B C { B K L h g F STOP Bx1.3/0.8 2 3 4 1 6 Disc Format Finalize Disc Protect OFF ON Formatting a disc 5 Format - Format Mode VR mode Video mode Video mode DVD Player Compatibility mode. VR mode Editing possibility mode. Formatting 90% Format Format Mode Video mode Start

Connections Getting started Changing the Setup menu Others Español DVD-RW DVD-RW Video DVD-RW DVD-RW VR If you are using a DVD-RW disc, by default it will be Video mode. You can change it to VR mode from the Setup menu. 1 Press [SETUP]. 2 Using [K / L], select “Disc”. Press [ENTER]. Disc menu will appear. 3 Using [K / L], select “Format”. Press [ENTER]. Format menu will appear. 4 Using [K / L], select “Start”. Press [ENTER]. Final confirm window will appear. 5 Using [K / L], select “Yes”. Press [ENTER]. Formatting will start. 6 Formatting is complete. “100%” will be indicated. Reformatting a disc Note • When you reformat the disc, the contents of the disc will be erased. • If you want to cancel format at step 4 or 5, select “No”. POWER ZOOM DISPLAY SETUP TOP MENU MENU/LIST REC SPEED REC/OTR PAUSE SKIP SKIP PLAY CM SKIP REPEAT OPEN/CLOSE TIMER PROG. FWD REV CLEAR 1 2 3 4 5 6 7 8 9 SPACE 0 A H G ENTER CH RETURN .@/: ABC DEF GHI JKL MNO PQRS TUV WXYZ B C { B K L h g F STOP Bx1.3/0.8 This operation may take a while to be completed. 2 3 4 5 1 Format Format Mode Video mode Start Formatting 90% Format Format mode Video mode Start Are you sure? Yes No DVD-RW DVD-RW Video DVD-RW DVD-RW VR 1 Press [SETUP]. 2 Using [K / L], select “Recording”. Press [ENTER]. 3 Using [K / L], select “Auto Chapter”. Press [ENTER]. Option window will appear. “10 minutes” has been selected as the default. 4 Using [K / L], select a desired time option. Press [ENTER]. 5 Press [SETUP] to exit. Setting for Auto Chapter Auto Chapter 5 minutes 10 minutes 15 minutes 30 minutes 60 minutes OFF POWER ZOOM DISPLAY SETUP TOP MENU MENU/LIST REC SPEED REC/OTR PAUSE SKIP SKIP PLAY CM SKIP REPEAT OPEN/CLOSE TIMER PROG. FWD REV CLEAR 1 2 3 4 5 6 7 8 9 SPACE 0 A H G ENTER CH RETURN .@/: ABC DEF GHI JKL MNO PQRS TUV WXYZ B C { B K L h g F STOP Bx1.3/0.8 2 3 4 5 1 Formatting a disc (cont’d)

and continues until the disc is full or you stop recording. • When the clock setting has not been made, the space for a date and time of title names in the Original list or Playlist will be blank. • When you record a TV program which has Stereo and SAP audio on a DVD- RW/R, you have to select the TV channel audio (Stereo or SAP) beforehand. Only the selected channel audio will be recorded. Refer to “Selecting the TV stereo or SAP” on page 20 for more details. • You cannot mix two formats on one DVD-RW disc. When you load a disc once recorded before, the recording format cannot be changed even if you change it in the Setup menu. • You cannot change the recording speed during the REC pause mode. • You can change a channel during the REC pause mode. DVD-RW DVD-RW Video DVD-RW DVD-RW VR DVD-R DVD-R Follow the steps below to record TV programs. 1 Turn on the unit. Load a record- able disc. Make sure that the TV input is set on the unit. 2 Using [REC SPEED], select a recording speed. Refer to “Recording speed” on page 24. 3 Using [CH K / L] or the Number buttons, select a desired chan- nel to record. 4 Press [REC/OTR] to start recording. “I” mark will be displayed for 5 seconds. Press [REC/OTR] to resume. Press [PAUSE F] or [REC/OTR] again to start recording again. 5 Press [STOP C] to stop record- ing. POWER ZOOM DISPLAY SETUP TOP MENU MENU/LIST REC SPEED REC/OTR PAUSE SKIP SKIP PLAY CM SKIP REPEAT OPEN/CLOSE TIMER PROG. FWD REV CLEAR 1 2 3 4 5 6 7 8 9 SPACE 0 A H G ENTER CH RETURN .@/: ABC DEF GHI JKL MNO PQRS TUV WXYZ B C { B K L h g F STOP Bx1.3/0.8 4 2 3 4 5 CH 12 XP 0:58 I This operation may take a while to be completed. This operation may take a while to be recognized. Basic recording 1

Connections Getting started Changing the Setup menu Others Español Note • The remaining recording time will appear on the display panel during a One- touch Timer Recording. Press [DISPLAY] to see it on the TV screen. • You cannot pause a One- touch Timer Recording. • Unlike a Timer Recording, you can perform the following operations during a One-touch Timer Recording. -Turning the power off -Using [REC/OTR] and [STOP C] • The unit will be turned off automatically under the following conditions. 1)No space remained on the disc 2)When a power failure occurs DVD-RW DVD-RW Video DVD-RW DVD-RW VR DVD-R DVD-R This is a simple way to set the recording time in blocks of 30 minutes. Check that the disc you are recording onto has enough space for the time you set. When the recording finishes the recorder automatically goes into standby. 1 Turn on the unit and load a recordable disc. Make sure that the TV input is set on the unit. 2 Using [REC SPEED], select a recording speed. Refer to “Recording speed” on page 24. 3 Using [CH K / L] or the Number buttons, select a desired chan- nel to record. 4 Press [REC/OTR] repeatedly to select desired recording time. Recording times appear on the TV screen (30 minutes to 8 hours). Recording will start. When the unit reaches the specified time, it will be turned off automatically. To change the recording length during the One-touch Timer Recording, press [REC/OTR] repeatedly until the desired length appear. To cancel the One-touch Timer Recording within the specified time, press [STOP C] . POWER ZOOM DISPLAY SETUP TOP MENU MENU/LIST REC SPEED REC/OTR PAUSE SKIP SKIP PLAY CM SKIP REPEAT OPEN/CLOSE TIMER PROG. FWD REV CLEAR 1 2 3 4 5 6 7 8 9 SPACE 0 A H G ENTER CH RETURN .@/: ABC DEF GHI JKL MNO PQRS TUV WXYZ B C { B K L h g F STOP Bx1.3/0.8 4 3 2 4 This operation may take a while to be recognized. 0:30 (Normal Recording) 8:00 7:30 1:00 I 0:30 This operation may take a while to be completed. One-touch Timer Recording

up to 8 programs within a month in advance. Daily or weekly program recordings are also available. • Be sure to set the clock before setting a timer programming. • Insert a recordable disc. 1 Press [TIMER PROG.]. Timer Programming list will appear. 2 Using [K / L], select a program number. Press [ENTER]. 3 Using [K / L], enter the Date. Press [B]. 4 Using [K / L], enter the Start and End. Press [B]. 5 Using [K / L], select the channel number to record. Press [B]. To record from external input, select L1 or L2. 6 Using [K / L], select a recording speed. Refer to “Recording speed” on page 24. POWER ZOOM DISPLAY SETUP TOP MENU MENU/LIST REC SPEED REC/OTR PAUSE SKIP SKIP PLAY CM SKIP REPEAT OPEN/CLOSE TIMER PROG. FWD REV CLEAR 1 2 3 4 5 6 7 8 9 SPACE 0 A H G ENTER CH RETURN .@/: ABC DEF GHI JKL MNO PQRS TUV WXYZ B C { B K L h g F STOP Bx1.3/0.8 Note • If you have not set the clock yet: A manual clock setting menu will appear instead of the Timer Programming list at step 1. Continue with the step 2 in “Manual Clock Setting” on page 22 before setting a timer programming. • Press [s / B] to move the cursor to the left and the right in the Timer Programming list. • After step 8, the recording will start immediately before the recording time you set. 1 2 3 4 5 6 Timer Programming 2. --- 3. --- 4. --- 5. --- 6. --- 7. --- 8. --- 1. JAN/01 12:57AM 1:57AM CH 8 Date Start End CH Speed Timer Programming 2. --- 3. --- 4. --- 5. --- 6. --- 7. --- 8. --- 1. JAN/01 12:57AM --:-- L1 Date Start End CH Speed Timer Programming 2. --- 3. --- 4. --- 5. --- 6. --- 7. --- 8. --- 1. JAN/01 --:-- --:-- L1 Date Start End CH Speed Timer Programming 2. --- 3. --- 4. --- 5. --- 6. --- 7. --- 8. --- 1. --- Date Start End CH Speed When pressing [L] at the current date, The Date will change as follows. Daily MON-SAT JAN/01 JAN/31 MON-FRI SAT FRI SUN L L L L L L L L Timer Programming 2. --- 3. --- 4. --- 5. --- 6. --- 7. --- 8. --- 1. JAN/01 12:57AM 1:57AM CH8 1H Date Start End CH Speed Timer Recording e.g. January 1st

information 7 Press [ENTER] when information is entered. Your program setting will be stored. • To set another program, repeat steps 2 to 7. • To exit, press [TIMER PROG.] or [SETUP]. • When two or more programs are overlapped, “Overlap” and the overlapped program number will appear in the display. 8 Press [POWER] to turn off. Recording Recording Playing discs Editing Before you start Connections Getting started Changing the Setup menu Others Español POWER ZOOM DISPLAY SETUP TOP MENU MENU/LIST REC SPEED REC/OTR PAUSE SKIP SKIP PLAY CM SKIP REPEAT OPEN/CLOSE TIMER PROG. FWD REV CLEAR 1 2 3 4 5 6 7 8 9 SPACE 0 A H G ENTER CH RETURN .@/: ABC DEF GHI JKL MNO PQRS TUV WXYZ B C { B K L h g F STOP Bx1.3/0.8 8 1 Press [POWER]. 2 Press [TIMER PROG.]. Timer Programming list will appear. 3 Check the information on the list you will need. 4 To clear the timer programming: Using [K / L], select your desired program. Press [CLEAR]. To correct the timer program- ming: Using [K / L], select your desired program. Press [ENTER]. Next, correct the timer programming by using [K / L / { / B]. Finally, Press [ENTER] again. 5 Press [TIMER PROG.] to exit. 6 Press [POWER] to return to the timer standby mode. Note • Press [TIMER PROG.] to check the timer programming in process. When the Timer Recording is proceeding, that program will be highlighted in red. 7 POWER ZOOM DISPLAY SETUP TOP MENU MENU/LIST REC SPEED REC/OTR PAUSE SKIP SKIP PLAY CM SKIP REPEAT OPEN/CLOSE TIMER PROG. FWD REV CLEAR 1 2 3 4 5 6 7 8 9 SPACE 0 A H G ENTER CH RETURN .@/: ABC DEF GHI JKL MNO PQRS TUV WXYZ B C { B K L h g F STOP Bx1.3/0.8 2 5 6 4 1 Press [CLEAR] to erase the selected program. Each error number means: Timer Programming 2. --- 3. --- 4. --- 5. --- 6. --- 7. --- 8. --- 1. JAN/01 12:57AM 1:57AM CH8 1H Date Start End CH Speed To stop the Timer Recording in process Press [STOP C] on the front panel of the unit. [STOP C] on the remote control is not effective. If the timer program did not complete correctly, the error number appears in the Timer Programming list. Timer Programming 2. --- 3. --- 4. --- 5. --- 6. --- 7. --- 8. --- * JAN/01 12:57AM 1:57AM CH8 E22 Date Start End CH Speed • A program with the error number is grayed and asterisked in the Timer Programming list. • Once the Timer Programming list with error line(s) is displayed, or after canceling and setting again the timer standby mode, the program line(s) with error will be cleared. indicator will appear on the front panel display. indicator disappears from the front panel display. Timer Recording (cont’d) E1-22 E37-39 Recording error other than below E35 PCA full E36 Already finalized Video format disc E23-24 Unrecordable disc E25-28 Copy prohibited program E40 Some portion has not been recorded because of program overlapping. Recording did not start at the start time. E29 Disc protected E30 Disc full E31-32 Already 99 titles recorded E33 Already 999 chapters recorded E41 Power failed E34 No space for Control information E42 No disc when recording

Note for DVD recording PROG. A PROG. B Actual recording The first 30 seconds (at the longest) will be cut off. PROG. B PROG. A When the End time of the programming currently being recorded and the Start time of the subsequent program are same: If PROG. A is a DVD recording program, the beginning of the PROG. B may be cut off. • When the recording time of two programs are overlapped, or the End time of a program and the Start time of another is the same, the first 30 seconds (at the longest) of the subsequent program will be cut off. • If the cut-off portion comes up to one minute or more, this program will be displayed with error number E40 in the timer programming list. The priority of overlapped settings PROG. A PROG. B Actual recording PROG. A PROG. B A programming set previously has priority When the starting time is same: A program set previously (PROG. A) has priority. The first 30 seconds (at the longest) will be cut off. PROG. A PROG. B Actual recording PROG. A PROG. B PROG. C When some programming have been made at the end time of the programming currently being recorded: A program set previously (PROG. B) has priority. The first 30 seconds (at the longest) will be cut off. PROG. A PROG. B Actual recording PROG.B PROG.A When the recording time is partially overlapped: PROG. A will start after PROG. B is complete to be recorded. The first 30 seconds (at the longest) will be cut off. PROG. A PROG. B Actual recording PROG. B When the recording time is entirely overlapped: PROG.A will not be recorded. • If there is a power failure or this unit has been unplugged for more than 30 seconds, the clock setting and all timer programming will be lost. • If a disc is not on the tray, the indicator flashes and Timer Recording cannot be performed. In some cases, the indicator appears momentarily around the start point as the unit attempts to record. Please insert a recordable disc. • When all the Timer Recording is completed, the indicator flashes. To play or eject the recorded disc, press [POWER] first, and then press [PLAY B] or [OPEN/CLOSE A]. • During the Timer Recording or timer standby ( indicator is on the front panel display), any operations on the unit will not be available. To make these operations available, cancel the Timer Recording or timer standby first ( indicator disappears). • To cancel the timer standby mode, press [POWER]. • When the Start and the End time are the same, the length of the recording will be set for 24 hours. When the disc reaches at the end during the recording, the unit turns itself off. • When the programmed Start and End time are earlier than the current time, the setting will not be accepted and be cleared for redoing. • If the Start time is earlier and the End time is later than the current time, the recording will start right after you turn the power off. This unit records the programs according to priority if the timer programmings are overlapped. The timer programming set previously has priority. A Timer Recording of lower priority will be canceled, start from the middle or stop on the way. Check the overlapped timer programmings and change the priority if necessary. Timer Recording (cont’d)

Connections Getting started Changing the Setup menu Others Español DVD-RW DVD-RW Video DVD-RW DVD-RW VR DVD-R DVD-R Connect the external source properly to the unit by using input jacks either LINE2 (Front) or LINE1 (Rear). When connecting an external equipment of monaural output to this unit, use AUDIO L jack of LINE2 (Front). Use commercially available S-Video or Video cable and an Audio cable for this connection. Connection to an external source 4. Using [K / L], select “L2 (Front)”. Press [ENTER]. 5. Using [K / L], select the input jack type to connect. Press [ENTER]. If you want to use S-VIDEO input jack, select “S-Video In”. If you want to use VIDEO input (Composite) jack, select “Video In”. 4. Using [K / L], select “L1 (Rear)”. Press [ENTER]. 5. Using [K / L], select the input jack type to connect. Press [ENTER]. If you want to use S-VIDEO IN jack, select “S-Video In”. If you want to use VIDEO IN (Composite) jack, select “Video In”. 1. Press [SETUP]. 2. Using [K / L], select “Required Setting”. Press [ENTER]. 3. Using [K / L], select “Select Video”. Press [ENTER]. REC/OTR REC SPEED OPEN/CLOSE CHANNEL REV FWD STOP PLAY POWER S-VIDEO VIDEO AUDIO L R Front of this unit Rear of this unit ANTENNA AUDIO IN VIDEO IN L R AUDIO OUT VIDEO OUT (L1) IN IN OUT OUT S-VIDEO COMPONENT VIDEO OUTPUT L Y PB/CB PR/CR R DIGITAL AUDIO OUTPUT PCM / BITSTREAM COAXIAL To LINE 2 IN To LINE 1 IN Another source (VCR camcorder etc.) VIDEO S- VIDEO AUDIO R L OUTPUT VIDEO S -VIDEO AUDIO L R OUTPUT S-Video cable Audio cable Video cable or AUDIO IN VIDEO IN L R IN S-VIDEO Audio cable S-Video cable Video cable or S-VIDEO VIDEO AUDIO L R or Select Video L2 (Front) Video In L1 (Rear) Video In Select Video L2 (Front) S-Video In L1 (Rear) Video In Select Video L2 (Front) Video In L1 (Rear) S-Video In Select Video - L2 (Front) S-Video In Video In Settings for an external source Select Video - L1 (Rear) S-Video In Video In

Recording from an external source 1. Turn the TV and this unit on, and be sure to select the input of the TV to which the unit is connected. Refer to the table on page 15. 2. Press [OPEN/CLOSE A] to open the disc tray. Place the disc to record properly. 3. Press [OPEN/CLOSE A] to close the disc tray. 4. Select the input of the unit which the external equipment is connected. (L2 or L1) • To use the input jacks on the back of this unit, select “L1” position by pressing [0], [0], [1] on the remote control or the [CHANNEL L / K] . • To use the input jacks on the front of this unit, select “L2” position by pressing [0], [0], [2] on the remote control or the [CHANNEL L / K] . 5. Select a recording speed pressing [REC SPEED]. Refer to “Recording speed” on page 24. 6. Press [REC/OTR] on the unit to start recording. 7. Press “Play” on the external source to record from. 8. Press [STOP C] on the unit to stop recording. POWER ZOOM DISPLAY SETUP TOP MENU MENU/LIST REC SPEED REC/OTR PAUSE SKIP SKIP PLAY CM SKIP REPEAT OPEN/CLOSE TIMER PROG. FWD REV CLEAR 1 2 3 4 5 6 7 8 9 SPACE 0 A H G ENTER CH RETURN .@/: ABC DEF GHI JKL MNO PQRS TUV WXYZ B C { B K L h g F STOP Bx1.3/0.8 4 Setting a disc to protect DVD-RW DVD-RW VR To prevent accidental recording, editing or erasing the titles, you can protect them from the Setting menu. 1 Press [SETUP]. 2 Using [K / L], select “Disc”. Press [ENTER]. Disc menu will appear. 3 Using [K / L], select “Disc Protect OFF ON”. Press [ENTER]. Confirm window will appear. 4 Using [K / L], select “Yes”. Press [ENTER]. A disc will be protected. POWER ZOOM DISPLAY SETUP TOP MENU MENU/LIST REC SPEED REC/OTR PAUSE SKIP SKIP PLAY CM SKIP REPEAT OPEN/CLOSE TIMER PROG. FWD REV CLEAR 1 2 3 4 5 6 7 8 9 SPACE 0 A H G ENTER CH RETURN .@/: ABC DEF GHI JKL MNO PQRS TUV WXYZ B C { B K L h g F STOP Bx1.3/0.8 1 2 3 4 Note • The Disc Protect setting is available only when a disc with VR mode is inserted. • You can select only the Disc Protect menu when a protected disc is inserted. To cancel the disc protect: • When you insert a disc protected with this unit, “Disc Protect ON → OFF” will appear instead of “OFF → ON”. To release the protect for the disc, select “Disc Protect ON → OFF” at step 3, then select “Yes”. REC/OTR REC SPEED OPEN/CLOSE CHANNEL REV FWD STOP PLAY POWER S-VIDEO VIDEO AUDIO L R 6 5 2 3 4 8 This operation may take a while to be recognized. XP SP LP EP SLP SEP (1H) (2H) (4H) (6H) (8H) (10H) This operation may take a while to be completed. No Yes Disc Protect OFF ON No Yes Disc Protect ON OFF Settings for an external source (cont’d)

Connections Getting started Changing the Setup menu Others Español Recording Note • Finalizing discs in Video mode automatically creates title menus. • Once you have finalized a disc recorded in Video mode, you cannot edit or record anything else on that disc. Discs recorded in VR mode can still be recorded and edited on this recorder even after finalized. • When you insert a DVD-RW disc finalized with this unit, “Undo Finalize” will appear instead of “Finalize”. To release the finalizing for the disc, select “Undo Finalize” at step 3. • DO NOT power off during finalizing, this will result in malfunction. DVD-RW DVD-RW Video DVD-RW DVD-RW VR DVD-R DVD-R You will need to finalize discs recorded in Video mode to play in other DVD players. Finalizing may take several minutes up to an hour. (A disc recorded in Video mode can take up to 15 minutes. A disc recorded in VR mode can take up to 60 minutes.) A shorter recording period on the disc will require a longer time period for finalization. Do not unplug the power cord during finalization. Details are on pages 24-25. 1 Press [SETUP]. 2 Using [K / L], select “Disc”. Press [ENTER]. Disc menu will appear. 3 Using [K / L], select “Finalize”. Press [ENTER]. Confirm window will appear. 4 Using [K / L], select “Yes”. Press [ENTER]. Finalizing will start. 5 Finalizing is complete. POWER ZOOM DISPLAY SETUP TOP MENU MENU/LIST REC SPEED REC/OTR PAUSE SKIP SKIP PLAY CM SKIP REPEAT OPEN/CLOSE TIMER PROG. FWD REV CLEAR 1 2 3 4 5 6 7 8 9 SPACE 0 A H G ENTER CH RETURN .@/: ABC DEF GHI JKL MNO PQRS TUV WXYZ B C { B K L h g F STOP Bx1.3/0.8 1 4 2 3 4 This operation may take a while to be completed. Finalizing 100% Finalizing 90% Finalize No Yes To cancel finalizing... (DVD-RW only) • To cancel finalizing at step 4, Press [STOP C], select “Yes”, then press [ENTER]. Finalizing is canceled and the unit will be in stop mode. • If appear when pressing [STOP C], you cannot cancel finalizing because the finalizing has been in certain progress. • When selecting “No” and press [ENTER] or [RETURN ] , finalizing will be continued. • You cannot cancel finalizing the DVD-R disc once it has started. Finalizing 5% Do you want to cancel ? Yes No Disc Format Undo Finalize Disc Protect OFF ON Finalizing the discs

REC SPEED REC/OTR PAUSE SKIP SKIP PLAY CM SKIP REPEAT OPEN/CLOSE TIMER PROG. FWD REV CLEAR 1 2 3 4 5 6 7 8 9 SPACE 0 A H G ENTER CH RETURN .@/: ABC DEF GHI JKL MNO PQRS TUV WXYZ B C { B K L h g F STOP Bx1.3/0.8 6 2 3 4 5 DVD-RW DVD-RW Video DVD-R DVD-R You can finalize discs automatically using Auto Finalize function. You can use this function to finalize discs after finishing all Timer Recordings and at the end of the disc space. 1 Press [SETUP]. 2 Using [K / L], select “Recording”. Press [ENTER]. Recording menu will appear. 3 Using [K / L], select “Auto Finalize”. Press [ENTER]. Auto Finalize menu will appear. 4 Using [K / L], select “Disc Full” or “End of Timer Rec”. Press [ENTER]. Option window will appear. 5 Using [K / L], select “ON”. Press [ENTER]. Your setting will be activated. 6 Press [SETUP] to exit. Auto finalize 1 Note • Auto Finalize does not function for VR format discs. Auto Finalize - End of Timer Rec OFF ON Auto Finalize End of Timer Rec Disc Full OFF OFF Auto Finalize - Disc Full OFF ON Finalizing the discs (cont’d)

Connections Getting started Changing the Setup menu Others Español Before you play DVD discs, read the following information. Guide to displays Playable discs This unit is compatible to play the following discs. To play a DVD, make sure that it meets the requirements for Region Codes and Color Systems as described followings. Discs that have the following logos will play on the unit. Other Disc types are not guaranteed to play. Color systems DVDs are recorded in different color systems throughout the world. The most common color system is NTSC (which is used primarily in the United States and Canada). This unit uses NTSC, so DVDs you play must be recorded in the NTSC system. You cannot play DVDs recorded in other color system . Region codes This unit has been designed to play DVD discs with Region One (1). DVDs must be labeled for ALL regions or for Region 1 in order to play on the unit. You cannot play DVDs that are labeled for other regions. Look for the symbols below on your DVDs. If these region symbols do not appear on your DVD, you cannot play the DVD in this unit. The number inside the globe refers to region of the world. A DVD labeled for a specific region can only play on the unit with the same region code. Hint for DVD playback The contents of DVD disc are generally divided into titles. Titles may be further subdivided into chapters. Logo Disc DVD-VIDEO DVD-RW (VIDEO/VR mode) DVD-R (VIDEO mode) CD-DA (AUDIO CD) CD-R (CD-DA FORMAT, MP3 files) CD-RW (CD-DA FORMAT, MP3 files) Track 1 Track 2 Track 3 Track 4 Track 5 Start Rec. Stop/Start Stop Rec. Start Rec. Stop Rec. Title 1 Title 2 Chapter 1 Chapter 1 Chapter 2 Chapter 3 Chapter 2 is a trademark of DVD Format/Logo Licensing Corporation. Information on DVD play Press [DISPLAY] to call up the Display menu. This menu will give you the information on the playing disc. Some operations are available while disc is playing. 1. Indicates a disc type and a format mode. NOTE: In some descriptions on this manual, only one disc type is indicated as an example. 2. Indicates a channel number. 3. Indicates a recording mode and possible recording time left. 4. Indicates a title number, chapter number and the time lapse of disc play. 5. Each icon means: 6. Indicates current disc status. : Search : Audio : Subtitle : Angle (except VR mode) : Repeat : Marker : Noise Reduction : Zoom : Surround DVD-R 1 1 0:00:00 XP 1:01 CH 8 Video mode 1 4 5 2 5 2 3 6 3

DVD-RW (Video mode) discs which are already finalized, a title list will be displayed instead of thumbnails. • You can resume play from where you stopped playing the disc. (Resume play) Refer to page 41 for details about resume play. • Some discs may start playback automatically. DVD-RW DVD-RW Video DVD-RW DVD-RW VR DVD-R DVD-R 1 Press [POWER]. When you are playing a DVD, turn the TV on and be sure to select the input to which the unit is connected. 2 Press [OPEN/CLOSE A] . The disc tray will open. 3 Insert your disc with its label fac- ing up. Align the disc to the disc tray guide. 4 Press [OPEN/CLOSE A] to close the disc tray. 5 Press [TOP MENU] to display the title menu. You can change “Original” or “Playlist” of VR mode using [MENU / LIST].

Connections Getting started Changing the Setup menu Others Español DVD-V DVD-V DVD-V DVD-V CD CD 1 Press [POWER]. When you are playing a DVD, turn the TV on and be sure to select the input to which the unit is connected. 2 Press [OPEN/CLOSE A] to open the disc tray. The disc tray will open. 3 Insert your disc with its label fac- ing up. Align the disc to the disc tray guide. 4 Press [PLAY B] to start play- back. Playback will start. If you are playing a DVD-Video disc, a menu may appear. Refer to page 40 for details about the Disc menu. 5 Press [STOP C] to stop play- back. Note • Some discs may start playback automatically. Note • The audio source of MP3 files cannot be recorded as digital sound by an MD or DAT deck. • Files whose extension is other than “.mp3(MP3)” will not be listed in the MP3 menu. • Some unplayable folders or tracks may be listed in the MP3 menu due to the recording status. POWER ZOOM DISPLAY SETUP TOP MENU MENU/LIST REC SPEED REC/OTR PAUSE SKIP SKIP PLAY CM SKIP REPEAT OPEN/CLOSE TIMER PROG. FWD REV CLEAR 1 2 3 4 5 6 7 8 9 SPACE 0 A H G ENTER CH RETURN .@/: ABC DEF GHI JKL MNO PQRS TUV WXYZ B C { B K L h g F STOP Bx1.3/0.8 1 2 5 4 POWER ZOOM DISPLAY SETUP TOP MENU MENU/LIST REC SPEED REC/OTR PAUSE SKIP SKIP PLAY CM SKIP REPEAT OPEN/CLOSE TIMER PROG. FWD REV CLEAR 1 2 3 4 5 6 7 8 9 SPACE 0 A H G ENTER CH RETURN .@/: ABC DEF GHI JKL MNO PQRS TUV WXYZ B C { B K L h g F STOP Bx1.3/0.8 1 2 MP3 MP3 1 In stop mode, press [TOP MENU] to call up the MP3 menu. • To exit the menu, press [TOP MENU] again. 2 Using [K / L], select a desired folder (group) or track. Press [ENTER]. When selecting track: Playback will start. When selecting the folder: The files in folder will appear. Press [K / L] to select the track or folder you want, then press [ENTER]. • Press [PLAY B], [ENTER] or [B] to move to the lower hierarchies. • Press [s] or [RETURN ] to the previous hierarchy. Hints for MP3 files: • Folders are known as Groups, files are known as Tracks. • Folders are accompanied by icon. • MP3 files are accompanied by icon. Reproduction will start from the selected track and go to the next one in turn. • The system can recognize up to 255 groups (or folders) and up to 999 tracks. • The name of group and track can be displayed in up to 29 characters. Unrecognizable characters will be replaced with asterisks. • If there are no files in the folder, “No Files” will be displayed. This unit recommends the files recorded under the following circumstances: • Sampling frequency: 44.1kHz or 48kHz. • Constant bit rate: 112kbps - 320kbps. Playing MP3 disc File List DISC NAME FOLDER NAME 1 FOLDER NAME 2 FOLDER NAME 3 FOLDER NAME 4 FOLDER NAME 5 FOLDER NAME 6 1 FILE NAME 1 2 FILE NAME 2 1/2 3 3 3 Basic playback (cont’d)

The Disc menu will appear. If the feature is not available, may appear on the TV screen. POWER ZOOM DISPLAY SETUP TOP MENU MENU/LIST REC SPEED REC/OTR PAUSE SKIP SKIP PLAY CM SKIP REPEAT OPEN/CLOSE TIMER PROG. FWD REV CLEAR 1 2 3 4 5 6 7 8 9 SPACE 0 A H G ENTER CH RETURN .@/: ABC DEF GHI JKL MNO PQRS TUV WXYZ B C { B K L h g F STOP Bx1.3/0.8 POWER ZOOM DISPLAY SETUP TOP MENU MENU/LIST REC SPEED REC/OTR PAUSE SKIP SKIP PLAY CM SKIP REPEAT OPEN/CLOSE TIMER PROG. FWD REV CLEAR 1 2 3 4 5 6 7 8 9 SPACE 0 A H G ENTER CH RETURN .@/: ABC DEF GHI JKL MNO PQRS TUV WXYZ B C { B K L h g F STOP Bx1.3/0.8 Press [MENU / LIST]. The Disc menu will appear. If the feature is not available, may appear on the TV screen. Playing discs Note • Menus vary among discs. Refer to the information accompanying the disc for details. Playing discs using the Disc menu DVD-V DVD-V DVD-V DVD-V A DVD disc contains a Disc menu that describes the contents or allows you to customize the playback. For example, the menu may offer choices for subtitle languages, special features, or chapter selection. Sometimes these are displayed automatically when you start playback, otherwise only appear when you press [MENU / LIST]. 1 2 Using [K / L / { / B], select an item. Press [ENTER] to confirm. Continue this step to set up all the features you want or to start playing the disc from the menu. MENU / LIST button: Displays a DVD Disc menu which varies with the disc and may be the same as the ‘Title menu.’ Cursor K / L / { / B buttons: Moves the cursor around screen. ENTER button: Selects the currently highlighted menu option. Number buttons: Selects a numbered menu option (some discs only). (Press [ENTER] after.) 3 Press [MENU / LIST] to exit the Disc menu. Note • [TOP MENU] will not always be active with all DVDs. • Menus vary among discs. Refer to the information accompanying the disc for details. Playing discs using the Title menu DVD-V DVD-V DVD-V DVD-V Some DVDs have a Title menu, which lists the titles available on them. It helps you to start play at a specific title. 1 2 Using [K / L / { / B], select a title to play. Press [ENTER]. Play will begin at the title you selected. TOP MENU button: Displays the ‘Title menu’ of a DVD disc which varies with the disc. Cursor K / L / { / B buttons: Moves the cursor around screen. ENTER button: Selects the currently highlighted menu option. Number buttons: Selects a numbered menu option (some discs only). (Press [ENTER] after.) 3 Press [TOP MENU] to exit the Title menu. 2 3 2 1 2 2 3 2 1 2 Pause DVD-V DVD-V DVD-V DVD-V DVD-RW DVD-RW Video DVD-RW DVD-RW VR DVD-R DVD-R CD CD MP3 MP3 1 During playback, press [PAUSE F]. Play will pause and sound will be muted. 2 Press [PLAY B] to resume play. POWER ZOOM DISPLAY SETUP TOP MENU MENU/LIST REC SPEED REC/OTR PAUSE SKIP SKIP PLAY CM SKIP REPEAT OPEN/CLOSE TIMER PROG. FWD REV CLEAR 1 2 3 4 5 6 7 8 9 SPACE 0 A H G ENTER CH RETURN .@/: ABC DEF GHI JKL MNO PQRS TUV WXYZ B C { B K L h g F STOP Bx1.3/0.8 1 2 F Basic playback (cont’d)

Connections Getting started Changing the Setup menu Others Español Resume play DVD-V DVD-V DVD-V DVD-V DVD-RW DVD-RW Video DVD-RW DVD-RW VR DVD-R DVD-R CD CD MP3 MP3 You can resume play from where you stopped playing the disc last. 1 During playback, press [STOP C]. The resume message will appear. 2 Press [PLAY B]. In a few seconds, play will resume from the point at which it stopped last. You can resume play at the same point even if you turn off the unit. To cancel the resume play and start playing the disc from the beginning, press [STOP C] the second time while the play is stopped. Fast forward / Fast reverse DVD-V DVD-V DVD-V DVD-V DVD-RW DVD-RW Video DVD-RW DVD-RW VR DVD-R DVD-R CD CD MP3 MP3 1 During playback, press [FWD D] or [REV E]. Every time you press [FWD D] or [REV E], approximate speed will be changed as follows. Fast forward or fast reverse playback across titles (for DVD discs) or tracks (for MP3) is not possible. For Audio CDs, approximate speed is fixed at x8 with sound. For MP3 files, approximate speed is fixed at x8 with sound. To return to the normal play, press [PLAY B]. DISPLAY SETUP TOP MENU MENU/LIST REC SPEED REC/OTR PAUSE SKIP SKIP PLAY CM SKIP REPEAT FWD REV CLEAR 1 2 3 4 5 6 7 8 9 SPACE 0 H G ENTER CH RETURN .@/: ABC DEF GHI JKL MNO PQRS TUV WXYZ B C { B K L h g F STOP Bx1.3/0.8 1 2 2 POWER ZOOM DISPLAY SETUP TOP MENU MENU/LIST REC SPEED REC/OTR PAUSE SKIP SKIP PLAY CM SKIP REPEAT OPEN/CLOSE TIMER PROG. FWD REV CLEAR 1 2 3 4 5 6 7 8 9 SPACE 0 A H G ENTER CH RETURN .@/: ABC DEF GHI JKL MNO PQRS TUV WXYZ B C { B K L h g F STOP Bx1.3/0.8 1 Note • For MP3 files, playback will resume from the beginning of the track at which playback was stopped. Skipping TV commercials during play DVD-V DVD-V DVD-V DVD-V DVD-RW DVD-RW Video DVD-RW DVD-RW VR DVD-R DVD-R You can skip TV commercials by pressing [CM SKIP], so that you can enjoy the recorded programs without interrupting. 1 During playback, press [CM SKIP]. Normal play will start at 30 seconds ahead from the point you press [CM SKIP]. Every time you press [CM SKIP], the searching point will be extended by 30 seconds ahead. You can press up to 6 times (180 seconds). e.g. Press [CM SKIP] once. POWER ZOOM DISPLAY SETUP TOP MENU MENU/LIST REC SPEED REC/OTR PAUSE SKIP SKIP PLAY CM SKIP REPEAT OPEN/CLOSE TIMER PROG. FWD REV CLEAR 1 2 3 4 5 6 7 8 9 SPACE 0 A H G ENTER CH RETURN .@/: ABC DEF GHI JKL MNO PQRS TUV WXYZ B C { B K L h g F STOP Bx1.3/0.8 1 Resume ON x20 Normal speed playback x2 x20 x5 x40 x40 FWD g REV g REV g REV g REV g REV g REV g FWD g FWD g FWD g FWD g FWD g B CM Skip 30 sec. Note • Forward/reverse speed will be indicated with icons as follows. Forward (Approx. Speed) x2: x20: x40: Reverse (Approx. Speed) x5: x20: x40: Special playback (forwarding 30 seconds) Playback will restart automatically.

DVD-V DVD-V DVD-V DVD-V DVD-RW DVD-RW Video DVD-RW DVD-RW VR DVD-R DVD-R 1 During playback, press [PAUSE F]. Play will pause and sound will be muted. 2 Press [SKIP G] repeatedly. The play will advance one frame (or step) at a time when you press [SKIP G] with the sound muted. To play step by step backward: Press [SKIP H] repeatedly. Every time you press the button, the play will go backward by one frame. • Press and hold [SKIP H / G] to reverse/ advance continuously. 3 Press [PLAY B] to resume play. Slow forward / Slow reverse play DVD-V DVD-V DVD-V DVD-V DVD-RW DVD-RW Video DVD-RW DVD-RW VR DVD-R DVD-R 1 During playback, press [PAUSE F]. Then press [FWD D] or [REV E]. Every time you press [FWD D] or [REV E], approximate speed will be changed as follows. (The sound will remain muted.) To return to the normal play, press [PLAY B]. POWER ZOOM DISPLAY SETUP TOP MENU MENU/LIST REC SPEED REC/OTR PAUSE SKIP SKIP PLAY CM SKIP REPEAT OPEN/CLOSE TIMER PROG. FWD REV CLEAR 1 2 3 4 5 6 7 8 9 SPACE 0 A H G ENTER CH RETURN .@/: ABC DEF GHI JKL MNO PQRS TUV WXYZ B C { B K L h g F STOP Bx1.3/0.8 1 3 2 POWER ZOOM DISPLAY SETUP TOP MENU MENU/LIST REC SPEED REC/OTR PAUSE SKIP SKIP PLAY CM SKIP REPEAT OPEN/CLOSE TIMER PROG. FWD REV CLEAR 1 2 3 4 5 6 7 8 9 SPACE 0 A H G ENTER CH RETURN .@/: ABC DEF GHI JKL MNO PQRS TUV WXYZ B C { B K L h g F STOP Bx1.3/0.8 1 F x1/8 Pause x1/16 x1/8 x1/16 x1/2 x1/4 FWD g REV g REV g REV g REV g REV g REV g FWD g FWD g FWD g FWD g FWD g Note • Slow forward/slow reverse speed will be indicated with icons as follows. Forward (Approx. Speed) x1/16: x1/8: x1/2: Reverse (Approx. Speed) x1/16: x1/8: x1/4: Rapid Play DVD-V DVD-V DVD-V DVD-V DVD-RW DVD-RW Video DVD-RW DVD-RW VR DVD-R DVD-R Rapid Play function is available only during playback. Available only on discs recorded in the Dolby Digital format, Rapid Play plays back in a slightly faster/slower speed while keeping the sound quality just as normal playback. 1 During playback, press [Bx1.3/0.8]. 2 Press [PLAY B] to continue the normal playback. B : Press [Bx1.3/0.8] once during playback. Plays back approximately at 0.8 times of normal playback. B : Press [Bx1.3/0.8] twice during playback. Plays back approximately at 1.3 times of normal playback. B : Press [Bx1.3/0.8] three times to play back in normal speed. No effects. Note • Audio (language) setting cannot be changed while using this mode. • This feature may not work at some point in a disc. • Audio is PCM during Rapid play mode. POWER ZOOM DISPLAY SETUP TOP MENU MENU/LIST REC SPEED REC/OTR PAUSE SKIP SKIP PLAY CM SKIP REPEAT OPEN/CLOSE TIMER PROG. FWD REV CLEAR 1 2 3 4 5 6 7 8 9 SPACE 0 A H G ENTER CH RETURN .@/: ABC DEF GHI JKL MNO PQRS TUV WXYZ B C { B K L h g F STOP Bx1.3/0.8 2 1 Special playback (cont’d)

Connections Getting started Changing the Setup menu Others Español Note • When selecting a smaller factor than the current one, the zoom area will not be displayed. • To exit the zoom menu, press [ZOOM] again at step 1. • To cancel the zoom function, select “x1.0” using [K / L], then press [ENTER]. Zoom DVD-V DVD-V DVD-V DVD-V DVD-RW DVD-RW Video DVD-RW DVD-RW VR DVD-R DVD-R 1 During playback, press [ZOOM]. Zoom menu will appear. There are four options (x1.0, x1.2, x1.5 and x2.0), these are displayed excluding the current zoom rate. 2 Using [K / L], select a desired zoom factor to zoom. Press [ENTER]. The zoom area will be displayed. 3 Using [K / L / { / B], select a desired zoom position. Press [ENTER]. The zoom play will start. POWER ZOOM DISPLAY SETUP TOP MENU MENU/LIST REC SPEED REC/OTR PAUSE SKIP SKIP PLAY CM SKIP REPEAT OPEN/CLOSE TIMER PROG. FWD REV CLEAR 1 2 3 4 5 6 7 8 9 SPACE 0 A H G ENTER CH RETURN .@/: ABC DEF GHI JKL MNO PQRS TUV WXYZ B C { B K L h g F STOP Bx1.3/0.8 1 2 3 Marker Setup DVD-V DVD-V DVD-V DVD-V DVD-RW DVD-RW Video DVD-RW DVD-RW VR DVD-R DVD-R CD CD This feature allows you to assign a specific point on a disc to be called back later. 1 During playback, press [DISPLAY]. The Display menu will appear. 2 Using [{ / B], select . Press [ENTER]. Marker Setup menu will appear.

The number next to will be highlighted. Title: Using [K / L] or the Number buttons, enter a desired title number to search. Press [ENTER]. Title search will start. Chapter: Press [B] to move to the number next to for chapter. Using [K / L] or the Number buttons, enter a desired chapter number to search. Press [ENTER]. Chapter search will start. Playing discs Title/Chapter search DVD-V DVD-V DVD-V DVD-V DVD-RW DVD-RW Video DVD-RW DVD-RW VR DVD-R DVD-R Using [SKIP H / G] 1 During playback, press [SKIP G] to skip the current title or chapter and move to the next. The title or chapter will move forward by one at a time. To go back to the beginning of the current title or chapter, press [SKIP H]. Press it repeatedly to go to the previous title or chapter. The title or chapter will move backward one title at a time. POWER ZOOM DISPLAY SETUP TOP MENU MENU/LIST REC SPEED REC/OTR PAUSE SKIP SKIP PLAY CM SKIP REPEAT OPEN/CLOSE TIMER PROG. FWD REV CLEAR 1 2 3 4 5 6 7 8 9 SPACE 0 A H G ENTER CH RETURN .@/: ABC DEF GHI JKL MNO PQRS TUV WXYZ B C { B K L h g F STOP Bx1.3/0.8 1 POWER ZOOM DISPLAY SETUP TOP MENU MENU/LIST REC SPEED REC/OTR PAUSE SKIP SKIP PLAY CM SKIP REPEAT OPEN/CLOSE TIMER PROG. FWD REV CLEAR 1 2 3 4 5 6 7 8 9 SPACE 0 A H G ENTER CH RETURN .@/: ABC DEF GHI JKL MNO PQRS TUV WXYZ B C { B K L h g F STOP Bx1.3/0.8 2 2 1 Using [DISPLAY] 1 During playback, press [DISPLAY]. The Display menu will appear. 2 Note • In search mode display, total numbers of each search contents (title/chapter/time) are shown as a denominator. 001/028 00:00:00/02:18:33 01 /01 Total number of titles Total number of chapters Total time DVD-Video 1 1 0:00:00 Search

The Display menu will appear.

only be set with in the current title (for DVDs), or current track (for Audio CDs). • To cancel the repeat playback, select “OFF” at step 2. The repeat setting will also be cancelled when you stop playback. • You cannot select “Group” during the random playback of MP3 files. Repeat play DVD-V DVD-V DVD-V DVD-V DVD-RW DVD-RW Video DVD-RW DVD-RW VR DVD-R DVD-R CD CD MP3 MP3 1 During playback, press [REPEAT]. Repeat menu will appear.

REC SPEED REC/OTR PAUSE SKIP SKIP PLAY CM SKIP REPEAT OPEN/CLOSE TIMER PROG. FWD REV CLEAR 1 2 3 4 5 6 7 8 9 SPACE 0 A H G ENTER CH RETURN .@/: ABC DEF GHI JKL MNO PQRS TUV WXYZ B C { B K L h g F STOP Bx1.3/0.8 Playing discs Recording Playing discs Editing Before you start Connections Getting started Changing the Setup menu Others Español Note • To erase tracks you selected, press [CLEAR]. • You can make program settings up to 50. • To cancel program play, press [STOP C] twice during program play. “Play mode OFF” appears on the screen. • You may also select a desired track using the Number buttons at step 4. Program play CD CD You can program the disc to play in your desired order. 1 Press [SETUP]. 2 Using [K / L], select “CD Playback Mode”. Press [ENTER]. CD Playback Mode menu will appear. 3 Using [K / L], select “Program Play”. Press [ENTER]. Program Play list will appear. 4 Using [K / L], select a desired track. Press [ENTER] or [B]. A cursor will move to next. 5 Press [PLAY B] to start program playback. Program playback will start. POWER ZOOM DISPLAY SETUP TOP MENU MENU/LIST REC SPEED REC/OTR PAUSE SKIP SKIP PLAY CM SKIP REPEAT OPEN/CLOSE TIMER PROG. FWD REV CLEAR 1 2 3 4 5 6 7 8 9 SPACE 0 A H G ENTER CH RETURN .@/: ABC DEF GHI JKL MNO PQRS TUV WXYZ B C { B K L h g F STOP Bx1.3/0.8 2 3 4 1 Selecting the format of audio and video You can select the format of audio and video as you prefer depending on the contents of the disc you are playing. Note • Some discs will only allow you to change the subtitle from the Disc menu. Press [TOP MENU] or [MENU / LIST] to display the Disc menu. • If a 4-digit language code appears in the subtitle menu at step 2, refer to the “Language code” on page 75. Switching subtitles DVD-V DVD-V DVD-V DVD-V DVD-RW DVD-RW VR Many DVD-Video discs have subtitles in one or more languages – the case usually tells you which subtitle languages are available. You can switch subtitle languages anytime during playback. 1 During playback, press [DISPLAY]. The Display menu will appear. 2 Using [{ / B], select . Press [ENTER]. Subtitle menu will appear. 3 Using [K / L], select a desired subtitle language. Press [ENTER]. Subtitle will be displayed in the selected language. When selecting “OFF”, subtitle will disappear. 1 2 3 5 Program Play 0:06:11 Total 09 -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- Program Play 0:00:00 Total -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- OFF 1.English 2.Japanese DVD-Video 1 1 0:00:00 DVD-Video 1 1 0:00:00 Repeat/Random/Program playback (cont’d)

you to change the soundtrack from the Disc menu. Press [TOP MENU] or [MENU / LIST] to display the Disc menu. • On DVD-RW discs recorded in VR mode that may have both a main and a sub audio channel, you can switch to main (L), sub audio (R) or a mix of both (L/R). • This unit CANNOT record in both stereo and SAP (Secondary Audio Program) at the same time. Switching audio soundtrack DVD-V DVD-V DVD-V DVD-V DVD-RW DVD-RW VR CD CD When playing a DVD-Video disc recorded with two or more soundtracks (these are often in different languages), you can switch them during playback. On DVD-RW discs recorded in VR mode, you can switch to main (L), sub audio (R) or a mix of both (L/R). When playing Audio CDs files you can switch between stereo, just the left channel or just the right channel. 1 During playback, press [DISPLAY]. The Display menu will appear. 2 Using [{ / B], select . Press [ENTER]. Audio menu will appear.

Connections Getting started Changing the Setup menu Others Español Switching camera angles DVD-V DVD-V DVD-V DVD-V Some DVD-Video discs feature scenes shot from two or more angles, check the case for details: it should be marked with Angle icon if it contains multi-angle scenes. 1 During playback, press [DISPLAY]. The Display menu will appear. Angle icon appears when a switching camera angle is available. 2 Using [{ / B], select . Press [ENTER]. Angle will switch each time you press [ENTER]. Reducing block noise DVD-V DVD-V DVD-V DVD-V DVD-RW DVD-RW Video DVD-RW DVD-RW VR DVD-R DVD-R 1 During playback, press [DISPLAY]. The Display menu will appear. 2 Using [{ / B], select . Press [ENTER]. Noise Reduction menu will appear. 3 Using [K / L], select a desired option. Press [ENTER]. Your setting will be activated. This function reduces noise in the playback picture. When playing back discs recorded in long time mode such as SLP or SEP mode, select “Type 1” or “Type 2”. (“Type 2” is more effective.) When playing back discs with a few noises such as DVD-Video discs, select “OFF”. POWER ZOOM DISPLAY SETUP TOP MENU MENU/LIST REC SPEED REC/OTR PAUSE SKIP SKIP PLAY CM SKIP REPEAT OPEN/CLOSE TIMER PROG. FWD REV CLEAR 1 2 3 4 5 6 7 8 9 SPACE 0 A H G ENTER CH RETURN .@/: ABC DEF GHI JKL MNO PQRS TUV WXYZ B C { B K L h g F STOP Bx1.3/0.8 2 1 POWER ZOOM DISPLAY SETUP TOP MENU MENU/LIST REC SPEED REC/OTR PAUSE SKIP SKIP PLAY CM SKIP REPEAT OPEN/CLOSE TIMER PROG. FWD REV CLEAR 1 2 3 4 5 6 7 8 9 SPACE 0 A H G ENTER CH RETURN .@/: ABC DEF GHI JKL MNO PQRS TUV WXYZ B C { B K L h g F STOP Bx1.3/0.8 2 3 1 DVD-Video 1 1 0:00:00 Type 1 Type 2 OFF DVD-Video 1 1 0:00:00 DVD-Video 1 1 0:00:00 Note Angle icon does not appear on the screen in a case you have selected Angle as “OFF” in the Display setting. Refer to pages 67-68. Selecting the format of audio and video (cont’d) 3 Using [K / L], select “OFF”, “Type1” or “Type2”. Press [ENTER]. DISPLAY SETUP TOP MENU MENU/LIST REC SPEED REC/OTR PAUSE SKIP SKIP PLAY CM SKIP REPEAT FWD REV CLEAR 1 2 3 4 5 6 7 8 9 SPACE 0 H G ENTER CH RETURN .@/: ABC DEF GHI JKL MNO PQRS TUV WXYZ B C { B K L h g F STOP Bx1.3/0.8 3 • OFF: no effect • Type1: Natural effect • Type2: Emphasised effect

Title list allows you to check the titles recorded on the disc easily. You can choose a title to play from this screen and easily edit the titles as you prefer. Press [TOP MENU]. 1. Titles recorded on the disc can be selected to edit or play by pressing [ENTER] with the cursor on the title. 2. The key icon, which appears when the title has been protected. (Original titles only) 3. The arrow icon, which means the Title list includes a next or a previous page. Press [{ / B] by following direction of the icon. 4. The menus in here for editing titles as you prefer. The available menus depend on the disc type and the format type. An item which is not available is grayed. 5. The details of the title, which can be changed to the title name you will edit. 6. Time status bar of the title. Time status will be held even after exiting the edit mode, and you can resume playback from that point. 7. The selected title thumbnail from the title list. 8. Playback status of the current disc. Editing discs in Video mode You can edit discs in Video mode for the following items. Be sure that once you edit titles, they will not remain as original. • Deleting titles (Refer to page 51) • Putting names on titles (Refer to page 52) • Setting or clearing chapter markers (Refer to page 53) Note • Once a disc is finalized, editing the disc or recording to the disc will not be available. (Except DVD-RW discs in VR mode.) • A Playlist is not available with the DVD-R discs and DVD-RW discs in Video mode. Editing discs in VR mode For discs in VR mode, you can edit from “Original” menu or “Playlist” menu, which is created from the original. Editing Original titles The following items can be used to edit the Original titles. • Deleting titles (Refer to page 54) • Setting titles to protect (Refer to page 55) • Releasing titles from protecting (Refer to page 56) Editing Playlists You can create a Playlist from Original titles, so that you can edit as you prefer without losing Original titles. The following items you can edit with a playlist. • Deleting titles (Refer to page 57) • Dividing a title (Refer to page 58) • Combining titles (Refer to page 59) • Adding titles to a Playlist (Refer to page 60) • Deleting a Playlist (Refer to page 60) Editing Original titles / Playlists The following items can be used to edit both the Original titles and the Playlists. • Deleting parts of titles (Refer to page 61) • Putting names on titles (Refer to page 62) • Setting or clearing chapter markers (Refer to page 63) • Setting pictures for thumbnails (Refer to page 64) Note • Original titles once edited will not remain as recorded originally. When you want to leave the original as it is, edit the Playlist as you prefer. Once all editings are made, press [RETURN ] in several times to exit the editing mode. “Writing to Disc” appears momentarily. This is true also when opening the disc tray, pressing [POWER] to turn the unit off. Original JAN/1 1:00AM CH12 XP 4 5 6 1 2 3 Original Edit Title Name Chapter Mark Index Picture Protect Scene Delete Title Delete JAN/1 1:00AM CH12 XP 0:00:59 6 1 3 7 4 6 5 8 2 3 Information on disc editing

Connections Getting started Changing the Setup menu Others Español Deleting titles DVD-R DVD-R DVD-RW DVD-RW Video You can delete titles which you do not need anymore. Be advised that the titles once deleted cannot be brought back to the disc. When the last title in the title list in Video mode is deleted, the disc space to record will be increased. For DVD-R disc, the disc space to record will not be changed. 1 Press [TOP MENU]. Title List will appear. 2 Using [K / L / { / B], select the desired title. Press [ENTER]. Option window will appear. 3 Using [K / L], select “Edit”. Press [ENTER] Edit menu will appear. You cannot select “Chapter Mark” when a DVD-R disc is inserted into the unit. “Chapter Mark” does not work on title less than 5 minutes. 4 Using [K / L], select “Title Delete”. Press [ENTER]. Confirm window will appear. 5 Using [K / L], select “Yes”. Press [ENTER]. After that, “Are you sure?” will appear, so that select “Yes” with [K / L] and then press [ENTER]. Title will be deleted. 6 Press [TOP MENU], [RETURN ] or [STOP C] to exit. Data will be written onto the disc momentarily. POWER ZOOM DISPLAY SETUP TOP MENU MENU/LIST REC SPEED REC/OTR PAUSE SKIP SKIP PLAY CM SKIP REPEAT OPEN/CLOSE TIMER PROG. FWD REV CLEAR 1 2 3 4 5 6 7 8 9 SPACE 0 A H G ENTER CH RETURN .@/: ABC DEF GHI JKL MNO PQRS TUV WXYZ B C { B K L h g F STOP Bx1.3/0.8 2 3 4 1 Title List JAN/1 1:00AM CH12 XP 4 5 6 1 2 3 Title List - Title Delete No Yes Are you sure? JAN/1 1:00AM CH12 XP 6 Editing discs in Video mode Title List JAN/1 1:00AM CH12 XP 4 5 1 2 3 6 Title List JAN/1 1:00AM CH12 XP 4 5 6 2 3 Play Edit Title List Title Delete Edit Title Name Chapter Mark JAN/1 1:00AM CH12 XP 0:00:59 6 Title List - Title Delete No Yes JAN/1 1:00AM CH12 XP 0:00:59 6 5

titles and change the names from this menu. The names you put on the titles will be displayed on a Title List. 1 Follow the steps 1 to 3 on page 51 to display the Edit menu. Using [K / L], select “Edit Title Name”. Press [ENTER]. A window for entering a title name will appear. 2 To enter a title name, follow the steps of “Guide to edit title name” on this page. character set area for entering title names When you finish entering a title name, press [ENTER]. Confirm window will appear. 3 Using [K / L], select “Yes”. Press [ENTER]. The name you entered will be activated for the title. 4 Press [RETURN ] and then [TOP MENU], [RETURN ] or [STOP C] to exit. Data will be written onto the disc momentarily. Putting names on titles POWER ZOOM DISPLAY SETUP TOP MENU MENU/LIST REC SPEED REC/OTR PAUSE SKIP SKIP PLAY CM SKIP REPEAT OPEN/CLOSE TIMER PROG. FWD REV CLEAR 1 2 3 4 5 6 7 8 9 SPACE 0 A H G ENTER CH RETURN .@/: ABC DEF GHI JKL MNO PQRS TUV WXYZ B C { B K L h g F STOP Bx1.3/0.8 3 2 4 1 2 This operation may take a while to be completed. Title List - Edit Title Name a b c A B C 1 2 3 @ ! ? JAN/1 1:00AM CH12 XP 0:00:59 6 Title List - Edit Title Name No Yes MY FAVORITE 6 0:00:59 Title List - Edit Title Name a b c A B C 1 2 3 @ ! ? M 0:00:59 6 Press ABC DEF GHI JKL MNO PQRS TUV WXYZ abc def ghi jkl mno pqrs tuv wxyz ! ” # $ % & ’ ( ) * + , - . / : ; < = > ? @ [ ] ^ _ { | } 2 3 4 5 6 7 8 9 0 1 ABC abc Select @ ! ? 123 1 1 2 2 3 4 5 6 7 8 9 9 0 *1 Press , character set will be changed to the “ @!? ” mode automatically. *2 Press to , character set will be changed to the previous input mode automatically. [Step1]: [Step2]: Follow the list below, press the Number buttons repeatedly until the desired letter appears. Select a desired character set using [K/L], then press [ENTER]. [ Guide to edit title name ] A B C a b c 1 2 3 @ ! ? • To delete letters, press [CLEAR] repeatedly. Holding [CLEAR] to delete all letters. • To go on to the next entering area for letters, press [B]. • You can enter up to 30 letters. (*1) (*1) (*2) (*2) (*2) (*2) (*2) (*2) (*2) (*2) e.g. character set : A B C A B C A... press 2 Note: Undefined letters in a title name are shown by “*”. If you delete them, adjoining letters letters may change to “*” or other. Editing discs in Video mode (cont’d)

Connections Getting started Changing the Setup menu Others Español Note • You cannot select a time for putting markers beyond a length of a title. • The length of chapters may be slightly longer or shorter than the one specified at the step 2. Setting or clearing chapter markers DVD-RW DVD-RW Video You can put chapter markers in each title. Once a chapter is marked, you can use it for the chapter search feature. You can set chapter markers at a specified time you selected for titles with more than 5 minutes. 1 Follow the steps 1 to 3 on page 51 to display the Edit menu. Using [K / L], select “Chapter Mark”. Press [ENTER]. Option window will appear. 2 Using [K / L], select desired time period. Press [ENTER]. Confirm window will appear. 3 Using [K / L], select “Yes”. Press [ENTER]. The marker will be added or deleting. 4 After this operation is complet- ed, press [RETURN ] and then [TOP MENU], [RETURN ] or [STOP C] to exit. Data will be written onto the disc momentarily. POWER ZOOM DISPLAY SETUP TOP MENU MENU/LIST REC SPEED REC/OTR PAUSE SKIP SKIP PLAY CM SKIP REPEAT OPEN/CLOSE TIMER PROG. FWD REV CLEAR 1 2 3 4 5 6 7 8 9 SPACE 0 A H G ENTER CH RETURN .@/: ABC DEF GHI JKL MNO PQRS TUV WXYZ B C { B K L h g F STOP Bx1.3/0.8 3 4 2 1 Title List - Chapter Mark - 5 minutes No Yes JAN/1 1:00AM CH12 XP 0:00:59 6 Title List - Chapter Mark JAN/1 1:00AM CH12 XP 0:00:59 6 5 minutes 10 minutes OFF 15 minutes 30 minutes 60 minutes Editing discs in Video mode (cont’d) This operation may take a while to be completed.

Original list in VR mode, the disc space to record will be increased. Be advised that the titles once deleted cannot be brought back to the disc. 1 Press [TOP MENU], and then press [MENU / LIST] to change “Playlist” to “Original”. Original list will appear. 2 Using [K / L / { / B], select the desired title. Press [ENTER]. Option window will appear. 3 Using [K / L], select “Edit”. Press [ENTER]. Original menu will appear. 4 Using [K / L], select “Title Delete”. Press [ENTER]. Confirm window will appear. 5 Using [K / L], select “Yes”. Press [ENTER]. After that, “Are you sure?” will appear, so that select “Yes” with [K / L] and then press [ENTER]. Title will be deleted. 6 After this operation is com- pleted, press [TOP MENU], [RETURN ] or [STOP C] to exit. Data will be written onto the disc momentarily. POWER ZOOM DISPLAY SETUP TOP MENU MENU/LIST REC SPEED REC/OTR PAUSE SKIP SKIP PLAY CM SKIP REPEAT OPEN/CLOSE TIMER PROG. FWD REV CLEAR 1 2 3 4 5 6 7 8 9 SPACE 0 A H G ENTER CH RETURN .@/: ABC DEF GHI JKL MNO PQRS TUV WXYZ B C { B K L h g F STOP Bx1.3/0.8 6 3 4 2 Deleting titles 1 This operation may take a while to be completed. Original - Title Delete Yes Are you sure? No JAN/1 1:00AM CH12 XP Wait for a moment. 3 Original - Title Delete No Yes JAN/1 1:00AM CH12 XP 0:00:59 3 Original Protect Title Delete JAN/1 1:00AM CH12 XP 0:00:59 3 Scene Delete Edit Title Name Chapter Mark Index Picture Original JAN/1 1:00AM CH12 XP 4 5 6 2 3 Play Edit Editing discs in VR mode (Original) 5

Connections Getting started Changing the Setup menu Others Español DVD-RW DVD-RW VR To prevent accidental editing, or erasing the titles, you can protect them from the Original menu. 1 Follow the steps 1 to 3 on page 54 to display the Original menu. Using [K / L]], select “Protect”. Press [ENTER]. Option window will appear. 2 Confirm the indication “OFF ON”. Press [ENTER]. The key icon will appear on the title in the Original list. 3 After this operation is complet- ed, press [RETURN ] and then [TOP MENU], [RETURN ] or [STOP C] to exit. Data will be written onto the disc momentarily. To protect a whole disc (DVD-RW VR mode Only): Select “Disc Protect” from the Disc menu, then select “Yes”. Refer to “Setting a disc to protect” on page 34. Setting titles to protect POWER ZOOM DISPLAY SETUP TOP MENU MENU/LIST REC SPEED REC/OTR PAUSE SKIP SKIP PLAY CM SKIP REPEAT OPEN/CLOSE TIMER PROG. FWD REV CLEAR 1 2 3 4 5 6 7 8 9 SPACE 0 A H G ENTER CH RETURN .@/: ABC DEF GHI JKL MNO PQRS TUV WXYZ B C { B K L h g F STOP Bx1.3/0.8 3 1 2 This operation may take a while to be completed. Original - Protect OFF ON JAN/1 1:00AM CH12 XP 3 Wait for a moment. Original - Protect OFF ON JAN/1 1:00AM CH12 XP 0:00:59 3 Editing discs in VR mode (Original) (cont’d)

titles protecting feature once protected. 1 Follow the steps 1 to 3 on page 54 to display the Original menu. Using [K / L], select “Protect”. Press [ENTER]. Option window will appear. 2 Confirm the indication “ON OFF”. Press [ENTER]. The key icon will disappear from the title in the Original list. 3 After this operation is complet- ed, press [RETURN ] and then [TOP MENU], [RETURN ] or [STOP C] to exit. Data will be written onto the disc momentarily. Releasing titles from protecting POWER ZOOM DISPLAY SETUP TOP MENU MENU/LIST REC SPEED REC/OTR PAUSE SKIP SKIP PLAY CM SKIP REPEAT OPEN/CLOSE TIMER PROG. FWD REV CLEAR 1 2 3 4 5 6 7 8 9 SPACE 0 A H G ENTER CH RETURN .@/: ABC DEF GHI JKL MNO PQRS TUV WXYZ B C { B K L h g F STOP Bx1.3/0.8 3 1 2 This operation may take a while to be completed. Original - Protect ON OFF JAN/1 1:00AM CH12 XP 3 Wait for a moment. Original - Protect ON OFF JAN/1 1:00AM CH12 XP 0:00:59 3 Editing discs in VR mode (Original) (cont’d)

Connections Getting started Others Español DVD-RW DVD-RW VR In VR mode, even when a title is deleted from a Playlist, the original title will remain in an Original list. The disc space to record will not be increased. 1 Press [TOP MENU] , and then press [MENU / LIST] to change “Original” to “Playlist”. Playlist will appear. 2 Using [K / L / { / B], select the desired title. Press [ENTER]. Option window will appear. 3 Using [K / L], select “Edit”. Press [ENTER]. Playlist menu will appear. 4 Using [K / L], select “Title Delete”. Press [ENTER]. Confirm window will appear. 5 Using [K / L], select “Yes”. Press [ENTER]. After that, “Are you sure?” will appear, so that select “Yes” with [K / L] and then press [ENTER]. Title will be deleted. 6 After this operation is com- pleted, press [TOP MENU], [RETURN ] or [STOP C] to exit. Data will be written onto the disc momentarily. Deleting titles POWER ZOOM DISPLAY SETUP TOP MENU MENU/LIST REC SPEED REC/OTR PAUSE SKIP SKIP PLAY CM SKIP REPEAT OPEN/CLOSE TIMER PROG. FWD REV CLEAR 1 2 3 4 5 6 7 8 9 SPACE 0 A H G ENTER CH RETURN .@/: ABC DEF GHI JKL MNO PQRS TUV WXYZ B C { B K L h g F STOP Bx1.3/0.8 2 3 4 1 6 Playlist Scene Delete Title Delete Edit Title Name Chapter Mark Index Picture Title Dividing Title Combining JAN/1 1:00AM CH12 XP 0:00:59 6 Playlist JAN/1 1:00AM CH12 XP 4 5 6 2 3 Play Edit Playlist - Title Delete No Yes Are you sure? JAN/1 1:00AM CH12 XP Wait for a moment. 3 Playlist - Title Delete No Yes JAN/1 1:00AM CH12 XP 0:00:59 3 This operation may take a while to be completed. Editing discs in VR mode (Playlist) Changing the Setup menu 5

Dividing a title DVD-RW DVD-RW VR You can divide a title into two new titles. 1 Follow the steps 1 to 3 on page 57 to display the Playlist menu. Using [K / L], select “Title Dividing”. Use [SKIP H / G], [REV E], [FWD D], [PLAY B] and [PAUSE F] to decide the point at which you will divide the title. Press [ENTER]. Confirm window will appear. 2 Using [K / L], select “Yes”. Press [ENTER]. The title will be divided into two new titles. Both title names are identical, and index pictures are reset to first scene at this point. 3 After this operation is com- pleted, press [TOP MENU], [RETURN ] or [STOP C] to exit. Data will be written onto the disc momentarily. Note • You cannot divide a title of the disc on which the number of recording title comes up to the maximum (99), and the number of recording chapter comes up to the maximum (999). POWER ZOOM DISPLAY SETUP TOP MENU MENU/LIST REC SPEED REC/OTR PAUSE SKIP SKIP PLAY CM SKIP REPEAT OPEN/CLOSE TIMER PROG. FWD REV CLEAR 1 2 3 4 5 6 7 8 9 SPACE 0 A H G ENTER CH RETURN .@/: ABC DEF GHI JKL MNO PQRS TUV WXYZ B C { B K L h g F STOP Bx1.3/0.8 3 2 1 This operation may take a while to be completed. Playlist - Title Dividing No Yes JAN/1 1:00AM CH12 XP Wait for a moment. 3 Playlist - Title Dividing No Yes JAN/1 1:00AM CH12 XP 0:00:59 3 F

Connections Getting started Others Español Changing the Setup menu Editing discs in VR mode (Playlist) (cont’d) Combining titles DVD-RW DVD-RW VR You can combine two titles into a single title. 1 Follow the steps 1 to 3 on page 57 to display the Playlist menu. Using [K / L], select “Title Combining”. Press [ENTER]. Title Combining setting window will appear. Selected title grays out, and the frame of the next title becomes yellow. 2 Using [K / L / s / B], select another title to combine. Press [ENTER]. Confirm window will appear. 3 Using [s / B], select “Yes”. Press [ENTER]. Two titles will combine into a single title. 4 After this operation is com- pleted, press [TOP MENU], [RETURN ] or [STOP C] to exit. Data will be written onto the disc momentarily. Note • You cannot combine the same titles into a single title. • If one of two titles in the original is deleted, the combined new title will be deleted automatically. • Selection order for the combining is affected in the combined new title. POWER ZOOM DISPLAY SETUP TOP MENU MENU/LIST REC SPEED REC/OTR PAUSE SKIP SKIP PLAY CM SKIP REPEAT OPEN/CLOSE TIMER PROG. FWD REV CLEAR 1 2 3 4 5 6 7 8 9 SPACE 0 A H G ENTER CH RETURN .@/: ABC DEF GHI JKL MNO PQRS TUV WXYZ B C { B K L h g F STOP Bx1.3/0.8 4 3 2 1 Playlist - Title Combining JAN/1 1:00AM CH12 XP 1 2 3 1 + Yes No Playlist - Title Combining 1 3 Wait for a moment. 2 1 + 2 Yes No Playlist - Title Combining 1 2 3 1 + 2 This operation may take a while to be completed.

Playlist as you prefer. You can add titles to a Playlist up to 99. 1 Follow the step 1 on page 57 to display the Playlist. Next to the final title, “Add New Title” “Delete Playlist” menu is shown. Using [K / L], select “Add New Title”. Press [ENTER]. 2 Using [K / L / s / B], select a desired title. Press [ENTER]. The added title will appear on the next to the selected title. 3 After this operation is completed, press [TOP MENU], [RETURN ] or [STOP C] to exit. Data will be written onto the disc momentarily. To delete a title from Playlist, refer to “Deleting titles” on page 57. To delete a Playlist, refer to “Deleting a Playlist” on this page. Adding titles to a Playlist Note • Deleting a Playlist will not increase the available recording time on disc. DVD-RW DVD-RW VR A Playlist can be deleted if no longer needed. 1 Follow the step 1 on page 57 to display the Playlist. Next to the final title, “Add New Title” “Delete Playlist” menu is shown. Using [K / L / s / B], select “Delete Playlist”. Press [ENTER]. Confirm window will appear. 2 Using [s / B], select “Yes”. Press [ENTER]. Final confirm window will appear. 3 Using [s / B], select “Yes”. Press [ENTER]. A Playlist will be erased. 4 After this operation is completed, press [TOP MENU], [RETURN ] or [STOP C] to exit. Data will be written onto the disc momentarily. Deleting a Playlist POWER ZOOM DISPLAY SETUP TOP MENU MENU/LIST REC SPEED REC/OTR PAUSE SKIP SKIP PLAY CM SKIP REPEAT OPEN/CLOSE TIMER PROG. FWD REV CLEAR 1 2 3 4 5 6 7 8 9 SPACE 0 A H G ENTER CH RETURN .@/: ABC DEF GHI JKL MNO PQRS TUV WXYZ B C { B K L h g F STOP Bx1.3/0.8 3 2 1 POWER ZOOM DISPLAY SETUP TOP MENU MENU/LIST REC SPEED REC/OTR PAUSE SKIP SKIP PLAY CM SKIP REPEAT OPEN/CLOSE TIMER PROG. FWD REV CLEAR 1 2 3 4 5 6 7 8 9 SPACE 0 A H G ENTER CH RETURN .@/: ABC DEF GHI JKL MNO PQRS TUV WXYZ B C { B K L h g F STOP Bx1.3/0.8 4 2 1 Note • When a Playlist contains 99 titles or more, or 999 chapters or more, “Add New Title” cannot be selected. This operation may take a while to be completed. Playlist - Add New Title JAN/1 1:00AM CH12 XP 1 4 2 5 3 Wait for a moment. Playlist - Add New Title JAN/1 1:00AM CH12 XP 1 2 3 Add New Delete Playlist Title Playlist Yes No 2 5 3 1 4 Add New Delete Playlist Title This operation may take a while to be completed. Editing discs in VR mode (Playlist) (cont’d) 3 Playlist Add New Delete Playlist Title Playlist Yes No 2 5 3 1 4 Add New Delete Playlist Title Wait for a moment. Are you sure? Are you sure?

a title. Even when a title is deleted from the Playlist, the original title will remain. The disc space to record will not be increased. 1 Press [TOP MENU], and then press [MENU LIST] to select “Original” or “Playlist”. 2 Using [K / L / { / B], select the desired title. Press [ENTER]. Option window will appear. 3 Using [K / L], select “Edit”. Press [ENTER]. Playlist menu will appear. 4 Using [K / L], select “Scene Delete”. Press [ENTER]. Option window will appear. 5 Use [SKIP H / G], [REV E], [FWD D], [PLAY B] and [PAUSE F] to decide the start point, then press [ENTER]. Then use [SKIP H / G], [REV E], [FWD D], [PLAY B] and [PAUSE F] again to move to the end point, and press [ENTER]. A cursor will move to “Preview”. The bar at the bottom of the screen indicates the total and the elapsed time of the title, and the area selected for deletion will be indicated in red. Press [ENTER] again to start the preview. You can check the result of deletion by “Preview”. 6 Using [K / L], select “Delete”. Press [ENTER]. Confirm window will appear. 7 Using [K / L], select “Yes”. Press [ENTER]. After that, “Are you sure?” will appear, so that select “Yes” with [K / L] and then press [ENTER]. Part of a title will be deleted. 8 After this operation is com- pleted, press [RETURN ] and then [TOP MENU], [RETURN ] or [STOP C] to exit. Data will be written onto the disc momentarily. Editing Recording Playing discs Editing Before you start Connections Getting started Others Español Changing the Setup menu Deleting parts of titles Note • You cannot select “Scene Delete” when the number of chapter markers is more than 900. Playlist - Scene Delete End Start Preview Delete JAN/1 1:00AM CH12 XP 0:00:59 3 This operation may take a while to be completed. Playlist - Scene Delete No Yes Are you sure? JAN/1 1:00AM CH12 XP Wait for a moment. 3 Playlist - Scene Delete No Yes JAN/1 1:00AM CH12 XP 0:00:59 3 Before editing Edited Start point End point Editing discs in VR mode (Original / Playlist) Playlist JAN/1 1:00AM CH12 XP 4 5 6 2 3 Play Edit Playlist Scene Delete Title Delete Edit Title Name Chapter Mark Index Picture Title Dividing Title Combining JAN/1 1:00AM CH12 XP 0:00:59 6 POWER ZOOM DISPLAY SETUP TOP MENU MENU/LIST REC SPEED REC/OTR PAUSE SKIP SKIP PLAY CM SKIP REPEAT OPEN/CLOSE TIMER PROG. FWD REV CLEAR 1 2 3 4 5 6 7 8 9 SPACE 0 A H G ENTER CH RETURN .@/: ABC DEF GHI JKL MNO PQRS TUV WXYZ B C { B K L h g F STOP Bx1.3/0.8 8 1 2 3 4 5 5 6 7

titles and change the names from this menu. The names you put on the titles will be displayed on a Title List. 1 Follow the steps 1 to 3 on page 61 to select “Original” or “Playlist”. 2 Using [K / L], select “Edit Title Name”. Press [ENTER]. A window for entering a title name will appear. 3 To enter a title name, follow the steps of “Guide to edit title name” on this page. character set area for entering title names When you finish entering a title name, press [ENTER]. Confirm window will appear. 4 Using [K / L], select “Yes”. Press [ENTER]. The name you entered will be activated for the title. 5 Press [RETURN ] and then [TOP MENU], [RETURN ] or [STOP C] to exit. Data will be written onto the disc momentarily. Putting names on titles POWER ZOOM DISPLAY SETUP TOP MENU MENU/LIST REC SPEED REC/OTR PAUSE SKIP SKIP PLAY CM SKIP REPEAT OPEN/CLOSE TIMER PROG. FWD REV CLEAR 1 2 3 4 5 6 7 8 9 SPACE 0 A H G ENTER CH RETURN .@/: ABC DEF GHI JKL MNO PQRS TUV WXYZ B C { B K L h g F STOP Bx1.3/0.8 2 3 3 This operation may take a while to be completed. Playlist - Edit Title Name a b c A B C 1 2 3 @ ! ? JAN/1 1:00AM CH12 XP 0:00:59 3 Playlist - Edit Title Name No Yes Wait for a moment. 3 MY FAVORITE Playlist - Edit Title Name a b c A B C 1 2 3 @ ! ? 0:00:59 3 M Press ABC DEF GHI JKL MNO PQRS TUV WXYZ abc def ghi jkl mno pqrs tuv wxyz ! ” # $ % & ’ ( ) * + , - . / : ; < = > ? @ [ ] ^ _ { | } 2 3 4 5 6 7 8 9 0 1 ABC abc Select @ ! ? 123 1 1 2 2 3 4 5 6 7 8 9 9 0 *1 Press , character set will be changed to the “ @!? ” mode automatically. *2 Press to , character set will be changed to the previous input mode automatically. [Step1]: [Step2]: Follow the list below, press the Number buttons repeatedly until the desired letter appears. Select a desired character set using [K/L], then press [ENTER]. [ Guide to edit title name ] A B C a b c 1 2 3 @ ! ? • To delete letters, press [CLEAR] repeatedly. Holding [CLEAR] to delete all letters. • To go on to the next entering area for letters, press [B]. • You can enter up to 30 letters. (*1) (*1) (*2) (*2) (*2) (*2) (*2) (*2) (*2) (*2) e.g. character set : A B C A B C A... press 2 Note: Undefined letters in a title name are shown by “*”. If you delete them, adjoining letters letters may change to “*” or other. Editing discs in VR mode (Original / Playlist) (cont’d) 4 5

Connections Getting started Changing the Setup menu Others Español DVD-RW DVD-RW VR You can put chapter markers in each title. Once a chapter is marked, you can use it for the chapter search feature. You can put a chapter marker anywhere you want. When the number of chapter markers in the Playlist comes to 999 in total, you cannot add any more chapter markers. 1 Follow the steps 1 to 3 on page 61 to select “Original” or “Playlist”. 2 Using [K / L], select “Chapter Mark”. Press [ENTER]. Option window will appear. 3 Use [SKIP H / G], [REV E], [FWD D], [PLAY B] and [PAUSE F] to decide the point at which you will create a new chapter marker. Or, use [SKIP H / G] to decide a chapter marker that you will delete. Select “Add” or “Delete” accordingly using [K / L] . Press [ENTER]. Confirm window will appear. • You cannot delete the first chapter of each title. 4 Using [K / L], select “Yes”. Press [ENTER]. When you select “Add” at step 3, a new chapter marker will be created at the point you have decided. When you select “Delete” at step 3, the chapter marker you have selected will be deleted. 5 After this operation is completed, press [RETURN ] twice and then [TOP MENU], [RETURN ] or [STOP C] to exit. Data will be written onto the disc momentarily. Setting or clearing chapter markers POWER ZOOM DISPLAY SETUP TOP MENU MENU/LIST REC SPEED REC/OTR PAUSE SKIP SKIP PLAY CM SKIP REPEAT OPEN/CLOSE TIMER PROG. FWD REV CLEAR 1 2 3 4 5 6 7 8 9 SPACE 0 A H G ENTER CH RETURN .@/: ABC DEF GHI JKL MNO PQRS TUV WXYZ B C { B K L h g F STOP Bx1.3/0.8 3 2 3 This operation may take a while to be completed. Chapter 2/ 2 Playlist - Chapter Mark - Add No Yes JAN/1 1:00AM CH12 XP Wait for a moment. 3 Palylist - Chapter Mark - Delete No Yes JAN/1 1:00AM CH12 XP 0:00:59 3 Chapter 2/ 2 F Playlist - Chapter Mark - Add No Yes JAN/1 1:00AM CH12 XP 0:00:59 3 Chapter 2/ 2 F Chapter 2/ 2 Palylist - Chapter Mark - Delete No Yes JAN/1 1:00AM CH12 XP Wait for a moment. 3 Playlist - Chapter Mark Delete Add JAN/1 1:00AM CH12 XP 0:00:59 3 Chapter 2/ 2 This operation may take a while to be completed. Editing discs in VR mode (Original / Playlist) (cont’d) 4 5

thumbnail is deleted by deleting a part of a title, a default picture will be selected. Setting pictures for thumbnails DVD-RW DVD-RW VR You can set a picture to each title for a thumbnail. It helps you to remember the contents of the title you are playing. The beginning picture has been selected as the default. 1 Follow the steps 1 to 3 on page 61 to select “Original” or “Playlist”. 2 Use [SKIP H / G], [REV E], [FWD D], [PLAY B] and [PAUSE F] to decide the picture you want to select as a thumbnail. Using [K / L], select “Index Picture”. Press [ENTER]. Confirm window will appear. 3 Using [K / L], select “Yes”. Press [ENTER]. A picture for thumbnail will be set. 4 After this operation is complet- ed, press [RETURN ] and then [TOP MENU], [RETURN ] or [STOP C] to exit. Data will be written onto the disc momentarily. POWER ZOOM DISPLAY SETUP TOP MENU MENU/LIST REC SPEED REC/OTR PAUSE SKIP SKIP PLAY CM SKIP REPEAT OPEN/CLOSE TIMER PROG. FWD REV CLEAR 1 2 3 4 5 6 7 8 9 SPACE 0 A H G ENTER CH RETURN .@/: ABC DEF GHI JKL MNO PQRS TUV WXYZ B C { B K L h g F STOP Bx1.3/0.8 2 This operation may take a while to be completed. Playlist - Index Picture No Yes JAN/1 1:00AM CH12 XP Wait for a moment. 3 Playlist - Index Picture No Yes JAN/1 1:00AM CH12 XP 0:00:59 3 F Editing discs in VR mode (Original / Playlist) (cont’d) 4 3

Recording Playing discs Editing Before you start Connections Getting started Others Español Note • If you change the setting in the Setup menu, the information of contents stays on even when the power is switched off. • An item which is not currently available is grayed in Setting menus. The following table is the contents which you can set and the default settings. Refer to the following table for useful operation. Tour of the Setup menu Changing the Setup menu Setup Items (highlight is the default) Contents 1.Language setting Pages 66-67 Disc Menu Language English French Spanish Set the language for the Disc menu. Audio Language Original English French Set the language for audio. Subtitle Language OFF English French Set the language for subtitle. 2.Display setting Pages 67-68 OSD Language English Français Español Set the language for OSD (On Screen Display). Angle Icon ON OFF Set the display or undisplay of multi- angle icon in a case the DVD in playback mode contains multi-angle scene. Screen Saver OFF 5 minutes 10 minutes Set the time to work the screen saver on the screen. FL Dimmer Auto Bright Dark Set the brightness of front panel display. 3.Audio setting Pages 68-70 Digital Out PCM 48kHz 96kHz Set whether the sound recorded in 96kHz will be down sampled in 48kHz. Dolby Digital PCM Stream Set the type of sound signal which outputs from the digital audio output jack. Dynamic Range Control ON OFF Compressing the range of sound volume. 4.Parental setting Pages 70-71 Parental Lock (Change password) ALL level 8 to 1 Set the parental level of your DVD discs. Enter the current four-digit password Set and change the password.

Language Audio Original Disc Menu English Subtitle OFF Language Audio Original Disc Menu English Subtitle OFF Language - Disc Menu French Spanish Other English Language - Audio English French Spanish Other Original Disc Menu Language (Default : English) Set the language for Disc Menu. • Using [K / L], select a setting. Press [ENTER]. Your setting will be activated. • Using [K / L], select a setting. Press [ENTER]. Your setting will be activated. • When Original is selected, the audio language will be in the disc’s default language. Audio Language (Default : Original) Set the Audio language. 1 Press [SETUP]. 2 Using [K / L], select “Playback”. Press [ENTER]. Playback menu will appear. 3 Using [K / L], select “Language”. Press [ENTER]. Language menu will appear. 4 Using [K / L], select a desired item. Press [ENTER]. Press [STOP C] if you are playing a disc. POWER ZOOM DISPLAY SETUP TOP MENU MENU/LIST REC SPEED REC/OTR PAUSE SKIP SKIP PLAY CM SKIP REPEAT OPEN/CLOSE TIMER PROG. FWD REV CLEAR 1 2 3 4 5 6 7 8 9 SPACE 0 A H G ENTER CH RETURN .@/: ABC DEF GHI JKL MNO PQRS TUV WXYZ B C { B K L h g F STOP Bx1.3/0.8 1 3 2 4 Language setting

Recording Playing discs Editing Before you start Connections Getting started Others Español If “Other” is selected, press 4-digit code using the Number buttons. Language - Subtitle Code Input - - - - • When you finish entering the code, press [ENTER]. Refer to “Language code” on page 75. 5 Press [SETUP] to exit. Note • Only the languages supported by the disc can be selected. • Audio Language setting may not be available to some discs. • You can change or switch off the subtitles on a DVD disc also from the Disc menu if it is available. • Press [CLEAR] or [s] to erase numbers entered incorrectly. Display setting 1 Press [SETUP]. 2 Using [K / L], select “Display”. Press [ENTER]. Display menu will appear. 3 Using [K / L], select a desired item. Press [ENTER]. Press [STOP C] if you are playing a disc. Instructions continue on the next page. Language Audio Original Disc Menu English Subtitle OFF Language - Subtitle OFF French Spanish Other English • Using [K / L], select a setting. Press [ENTER]. Your setting will be activated. Subtitle Language (Default : OFF) Set the Subtitle language. POWER ZOOM DISPLAY SETUP TOP MENU MENU/LIST REC SPEED REC/OTR PAUSE SKIP SKIP PLAY CM SKIP REPEAT OPEN/CLOSE TIMER PROG. FWD REV CLEAR 1 2 3 4 5 6 7 8 9 SPACE 0 A H G ENTER CH RETURN .@/: ABC DEF GHI JKL MNO PQRS TUV WXYZ B C { B K L h g F STOP Bx1.3/0.8 5 POWER ZOOM DISPLAY SETUP TOP MENU MENU/LIST REC SPEED REC/OTR PAUSE SKIP SKIP PLAY CM SKIP REPEAT OPEN/CLOSE TIMER PROG. FWD REV CLEAR 1 2 3 4 5 6 7 8 9 SPACE 0 A H G ENTER CH RETURN .@/: ABC DEF GHI JKL MNO PQRS TUV WXYZ B C { B K L h g F STOP Bx1.3/0.8 1 2 3 Language setting (cont’d) Changing the Setup menu

REC SPEED REC/OTR PAUSE SKIP SKIP PLAY CM SKIP REPEAT OPEN/CLOSE TIMER PROG. FWD REV CLEAR 1 2 3 4 5 6 7 8 9 SPACE 0 A H G ENTER CH RETURN .@/: ABC DEF GHI JKL MNO PQRS TUV WXYZ B C { B K L h g F STOP Bx1.3/0.8 Changing the Setup menu Display Angle Icon ON Screen Saver FL Dimmer 10 minutes Bright OSD Language English OSD Language Français Español English • Using [K / L], select a setting. Press [ENTER]. Your setting will be activated. OSD Language (Default : English) Set the language for OSD. Display Angle Icon ON Screen Saver FL Dimmer 10 minutes Bright OSD Language English FL Dimmer Bright Dark Auto • Using [K / L], select a setting. Press [ENTER]. Your setting will be activated. • If “Auto” is selected, the display is shown brighter when the power is on, darker when the power is off. FL Dimmer (Default : Bright) Set the brightness of front panel display. You can choose one among “Auto”, “Bright” and “Dark”. Display Angle Icon ON Screen Saver FL Dimmer 10 minutes Bright OSD Language English Screen Saver 5 minutes 10 minutes OFF 15 minutes 30 minutes • Using [K / L], select a setting. Press [ENTER]. Your setting will be activated. Screen Saver (Default : 10 minutes) Set the time to work the screen saver function on the screen. 4 Press [SETUP] to exit. 1 Press [SETUP]. Press [STOP C] if you are playing a disc. Choose the appropriate Audio settings for your equipment. It will only affect DVD discs during playback. Audio setting POWER ZOOM DISPLAY SETUP TOP MENU MENU/LIST REC SPEED REC/OTR PAUSE SKIP SKIP PLAY CM SKIP REPEAT OPEN/CLOSE TIMER PROG. FWD REV CLEAR 1 2 3 4 5 6 7 8 9 SPACE 0 A H G ENTER CH RETURN .@/: ABC DEF GHI JKL MNO PQRS TUV WXYZ B C { B K L h g F STOP Bx1.3/0.8 4 1 Display Angle Icon ON Screen Saver FL Dimmer 10 minutes Bright OSD Language English Angle Icon OFF ON • Using [K / L], select a setting. Press [ENTER]. Your setting will be activated. Angle Icon (Default : ON) Set to ON or OFF. Display setting (cont’d)

Recording Playing discs Editing Before you start Connections Getting started Others Español 2 Using [K / L], select “Playback”. Press [ENTER]. Playback menu will appear. 3 Using [K / L], select “Audio”. Press [ENTER]. Digital Out Set the digital audio output. • Using [K / L], select a setting. Press [ENTER]. Option window will appear. Proceed to step A or B. Settings for Dolby Digital (Default : Stream) • Using [K / L], select a setting. Press [ENTER]. Your setting will be activated. PCM :Convert the Dolby Digital into PCM(2 channel). When your amplifier/decoder is NOT compatible with Dolby Digital, set to “PCM”. Stream :Outputs Dolby Digital signals. When your amplifier/decoder is compatible with Dolby Digital, set to “Stream”. Settings for PCM (Default : 48kHz) • Using [K / L], select a setting. Press [ENTER]. Your setting will be activated. 48kHz :If your amplifier/decoder is NOT compatible with 96kHz PCM, select “48kHz”. 96kHz sound will be output in 48kHz. 96kHz :If your amplifier/decoder is compatible with 96kHz PCM, select “96kHz”. 96kHz sound will be output. B A Note When playing disc with copyright protection • Even if you select “96kHz”, the sound will be down sampled at 48kHz. Note When playing a DVD- RW disc recorded in VR mode • If the audio source on a disc is Dolby Digital format, set “Dolby Digital” to “PCM” so that you can switch to main (L), sub audio (R), or a mix of both (L/ R) with your amplifier/ decoder. Note • Dynamic Range Control function is available only on the discs which are recorded in the Dolby Digital format. POWER ZOOM DISPLAY SETUP TOP MENU MENU/LIST REC SPEED REC/OTR PAUSE SKIP SKIP PLAY CM SKIP REPEAT OPEN/CLOSE TIMER PROG. FWD REV CLEAR 1 2 3 4 5 6 7 8 9 SPACE 0 A H G ENTER CH RETURN .@/: ABC DEF GHI JKL MNO PQRS TUV WXYZ B C { B K L h g F STOP Bx1.3/0.8 2 3 Audio Dynamic Range Control ON Digital Out Audio - Digital Out Dolby Digital Stream PCM 48kHz Instructions continue on the next page. Audio setting (cont’d) Changing the Setup menu Digital Out - PCM 96kHz 48kHz Digital Out - Dolby Digital Stream PCM

Note • Parental lock function may not be available to some discs. • With some DVDs, it may be difficult to find if they are compatible with parental lock. Be sure to check if the parental lock function operates in the way that you have set. • Record the password in case you forget it. • Using [K / L], select a setting. Press [ENTER]. Your setting will be activated. Dynamic Range Control (Default : ON) Set to ON to compress the range between soft and loud sounds. 4 Press [SETUP] to exit. Settings for Parental lock level 1 Press [SETUP]. 2 Using [K / L], select “Playback”. Press [ENTER]. Playback menu will appear. 3 Using [K / L], select “Parental Lock”. Press [ENTER]. 4 Using [K / L], select the desired level. Press [ENTER]. Press [STOP C] if you are playing a disc. Some DVD-Video discs feature a Parental Lock level. Playback will stop if the ratings exceed the levels you set, it will require you to enter a password before the disc will playback. This feature prevents your children from viewing inappropriate material. POWER ZOOM DISPLAY SETUP TOP MENU MENU/LIST REC SPEED REC/OTR PAUSE SKIP SKIP PLAY CM SKIP REPEAT OPEN/CLOSE TIMER PROG. FWD REV CLEAR 1 2 3 4 5 6 7 8 9 SPACE 0 A H G ENTER CH RETURN .@/: ABC DEF GHI JKL MNO PQRS TUV WXYZ B C { B K L h g F STOP Bx1.3/0.8 4 POWER ZOOM DISPLAY SETUP TOP MENU MENU/LIST REC SPEED REC/OTR PAUSE SKIP SKIP PLAY CM SKIP REPEAT OPEN/CLOSE TIMER PROG. FWD REV CLEAR 1 2 3 4 5 6 7 8 9 SPACE 0 A H G ENTER CH RETURN .@/: ABC DEF GHI JKL MNO PQRS TUV WXYZ B C { B K L h g F STOP Bx1.3/0.8 4 1 4 3 2 Audio Digital Out Dynamic Range Conrtol ON Audio - Dynamic Range Control OFF ON Audio setting (cont’d)

Recording Playing discs Editing Before you start Connections Getting started Others Español Parental Lock (Default : All) Set the Parental Lock level. • Using [K / L], change the parental level. Press [ENTER]. Option window will appear Proceed to step A or B. • Using [K / L], select “Yes”. Using the Number buttons, enter a new password. Press [ENTER]. Your setting will be activated. • If you select “No”, proceed to Step 5. Yes A A password has not been set yet. Note • Press [CLEAR] to erase numbers entered incorrectly. • When you forget the password or you want to clear all settings in Parental lock, enter 4,7,3,7 using the Number buttons in Password Input window. Password will be cleared and parental levels will be set to All. Parental Lock Password Input - - - - • Using [K / L], select “Yes”. Using the Number buttons, enter a new password. Press [ENTER]. Your setting will be activated. 5 Press [SETUP] to exit. A password has been set already. Parental Lock Yes No Change Password? Parental Lock Password Input * * * * Yes • If you select “No”, proceed to Step 5. • Using the Number buttons, enter the current password. B POWER ZOOM DISPLAY SETUP TOP MENU MENU/LIST REC SPEED REC/OTR PAUSE SKIP SKIP PLAY CM SKIP REPEAT OPEN/CLOSE TIMER PROG. FWD REV CLEAR 1 2 3 4 5 6 7 8 9 SPACE 0 A H G ENTER CH RETURN .@/: ABC DEF GHI JKL MNO PQRS TUV WXYZ B C { B K L h g F STOP Bx1.3/0.8 5 Playback Video Audio Parental Lock All Language Parental Lock 8 7 6 5 4 3 2 1 All Parental Lock Yes No Change Password? Parental Lock Password Input - - - - Settings for Parental lock level (cont’d) Changing the Setup menu

experiencing. Some simple checks or a minor adjustment on your part may eliminate the problem and restore proper operation. Troubleshooting Symptom Remedy Power The power does not turn on. • Check that the AC power cord is connected securely. • (In case of power failure) Check the breaker. Picture There is no picture. • Re-connect the connecting cords securely. • Check if the connecting cords are damaged. • If Setup Display appears on the TV screen, press [RETURN ] to turn off the display. • Check the connection to your TV (page 13). • Check if the INTERLACE/PROGRESSIVE mode is set correctly according to your TV (page 13). • Switch the input selector on your TV (such as to “LINE1”) so that the signal from the unit appears on the TV screen. Picture noise appears. • The disc is dirty or flawed. • If the picture output signal from the unit passes through your VCR to get to your TV, or if you are connected to a combination TV/ VIDEO player, the copy-protection signal applied to some DVD programs could affect picture quality. If you still experience this problem even when you connect the unit directly to your TV, try connecting the unit to your TV’s S-VIDEO input. TV program reception does not fill the screen. • Try to set the channels with “Auto Preset” in the Setup menu (page 18). • Select a channel of any TV program using [CH K / L]. TV program pictures are distorted. • Adjust TV antenna. • Adjust the picture (see the TV’s instruction manual). • Place the unit and TV farther apart. • Place the TV and any bunched antenna cables farther apart. TV channels cannot be changed. • Switch the input to TV. • Connect the antenna cable correctly (page 13). Playback picture is distorted • Keep the equipment which may cause electrical disturbances, such as a cellular phone, away. The playback picture or TV program from the equipment connected through the unit is distorted. • If the playback picture output from a DVD player, VCR or tuner goes through the unit before reaching your TV, the copy-protection signal applied to some programs could affect picture quality. Disconnect the playback equipment in question and connect it directly to your TV. Sound There is no sound. • The disc is dirty or flawed. • Re-connect all connections securely. • Check if the connecting cord is damaged. • Check the connections to the amplifier input. • The input source setting on the amplifier is incorrect. • The recorder is in pause mode or in Slow-motion Play mode. • The recorder is in fast forward or fast reverse mode. • If the audio signal does not come through the DIGITAL OUT (COAXIAL) jack, check the Audio settings (pages 68-70). Sound is noisy. • The disc is dirty or flawed. No DTS sound is output. • This unit is not compatible with DTS sound. Remote control The remote control does not function. • Batteries are weak. • There are obstacles between the remote control and the unit. • The remote control is far from the unit. • There are no batteries in the remote control. • Turn on the unit. • The remote control is not pointed at the remote sensor on the unit. • If above remedies do not solve the problem, please call an Authorized Service Center for help.

Connections Getting started Others Español Troubleshooting (cont’d) Changing the Setup menu Symptom Remedy Playback The disc does not play. • No disc is inserted. • A blank disc is inserted. • The disc is upside down. Insert the disc with the labeled side facing up. • The disc is not correctly inserted. • The unit cannot play certain discs (such as a CD-ROM) (page 37). • The region code on the DVD-Video does not match the unit (page 37). • Moisture has condensed inside the unit. Remove the disc and leave the unit turned on for about two hours until the moisture evaporates (page 4). • If the disc was recorded on another recorder, the unit cannot play the disc if it was not finalized (page 35). Playback image freezes for a second. • During the playback of two layered disc, picture may freeze for a moment when the 1st layer switches to the 2nd layer. This is not a malfunction. The disc does not start playback from the beginning. • Resume play was activated (page 41). Press [STOP C] twice. • You have inserted a disc whose Title menu or DVD menu automatically appears on the TV screen when it is first insert. The unit starts playing from the disc automatically. • The DVD-Video features an auto playback function. Some functions such as Stop, Search, or Slow-motion Play cannot be performed. • Depending on the disc, you may not be able to do some of the operations above. See the instruction manual supplied with the disc. The language for the sound track cannot be changed. • Multilingual tracks are not recorded on the DVD-Video, DVD-R or DVD-RW being played. • The DVD-Video prohibits the changing of the language for the sound track. • Try changing the language using the DVD-Video’s menu. The subtitle language cannot be changed or turned off. • Multilingual subtitle are not recorded on the DVD-Video. • The DVD-Video prohibits changing of the subtitles. • Try changing the subtitle using the DVD-Video’s menu. The angles cannot be changed. • Multi-angles are not recorded on the DVD-Video being played. • The angle-change operation is whenever possible as long as the disc contains a multi-angle portion. Actual change will be performed when the portion has come up. • The DVD-Video prohibits changing angles. • Try changing the angle using the DVD-Video’s menu. Recording/Timer Recording/Editing The channel cannot be changed from the channel you are recording. • Set the TV’s input to “TV”. Recording does not start immediately after you press [REC/OTR]. • An unused DVD-R or DVD-RW has been inserted. It takes a while for the unit to automatically format a DVD-RW. Nothing was recorded even though you set the timer setting correctly. • There was a power failure during recording. • The unit’s internal clock stopped due to a power failure that lasted for more than 30 seconds. Reset the clock (pages 21- 22). • Disconnect the AC power cord from the AC outlet, and connect it again. • The program contains copy protection signals that restricts copying. • The timer setting overlapped with another setting that was set later or has priority. Recording does not stop immediately after you press [STOP C]. • It will take a few seconds for the unit to input disc data before recording can stop. Timer Recording is not complete or did not start from the beginning. • The timer setting overlapped with another setting that was set previously has priority (page 32). • Disc space was not enough.

• When static electricity, etc., causes the unit to operate abnormally, unplug the unit and then plug it in again. The disc tray does not open when you press [OPEN/CLOSE A]. • It may take a few seconds for the disc tray to open after you have recorded or edited a disc. “Repairing” appears on the display. • If there is a power failure or unplugging during recording, finalizing, formatting or editing (even after “Wait for a moment.” message is disappeared), a Repairing process will begin automatically just after turning the unit on again. It may take several minutes up to about four hours. • If you intend to cancel the Repairing process, press [OPEN/CLOSE A] on the front panel, then select “Yes” with [{ / B] and press [ENTER]. After that, press [OPEN/CLOSE A] to take out the disc. The disc canceled the Repairing process MAY NOT work. Repairing 90% In a case you intend to cancel the Repairing process. Repairing 90% Do you want to cancel a repairing process ? When selecting “Yes”, the disc may not be usable. Yes No Others Troubleshooting (cont’d) Error message Cause Solution Disc Error --- Please eject the disc. --- Playback feature may not be available on this Disc. • Unplayable disc is inserted in the unit. • The disc is upside down. • Insert the standardized disc which bear the marks on page 37. • Insert the disc with the labeled side facing up. Region Error --- Please eject the disc. --- Playback is not authorized in your region. • Playback is not authorized in the region of the DVD-Video disc which you inserted in the unit. • Insert the DVD-Video disc with region codes 1 or ALL. Parental Lock On The current selected parental level prohibits playback. • The current selected parental level in the Setup menu prohibits playback. • Check the “Parental Lock” setting (pages 70-71). Recording Error This program is not allowed to be recorded. • The recording function encountered the copy prohibited program. • You cannot record copy prohibited programs. Recording Error This program is not recordable in Video mode. • You are trying to record the copy- once program onto the DVD-RW disc in Video mode. • Set “Format mode” to “VR mode”(page 26). Recording Error Can not record on this disc. • You are trying to record onto the disc which is unrecordable, or the disc status is unable to record. • The disc is dirty. • The disc is damaged. • Insert the recordable disc, and ensure the disc status satisfies the recording requirements (pages 24-25). • Clean the disc with a cleaning cloth. • Replace the disc. Recording Error This program is not allowed to be recorded on this disc. • You are trying to record the copy- once program onto the DVD-RW disc which is not compatible with CPRM. • Insert the DVD-RW disc in VR mode (ver.1.1 or 1.2 compatible with CPRM). Recording Error This disc is protected and not recordable. • You are trying to record on to the protected disc which is set in the Disc menu. • Release the disc protect setting in the Disc menu (page 34). Recording Error Disc is full. (No area for new recording) • You are trying to record onto the disc which has no space for recording. • Insert the recordable disc with enough recording space.

Connections Getting started Others Español Language code * If you are still having trouble with the unit after checking “Troubleshooting”, write down the error code and the error description for calling our help line mentioned on the front page to locate an Authorized Service Center. Troubleshooting (cont’d) Changing the Setup menu Error message Cause Solution Recording Error You cannot record more than 99 titles on one disc. (The maximum is 99) You are trying to record onto the disc on which the number of recording titles comes up to the maximum (99). Delete unnecessary titles (pages 51, 54). Recording Error You cannot record more than 999 chapters on one disc. (The maximum is 999) You are trying to record onto the VR mode DVD-RW disc on which the number of recording chapters comes up to the maximum (999). Delete unnecessary chapter markers (page 63). Recording Error You cannot record on this disc as Control Information is full. This disc has no space to write the Control Information when recording or deleting contents. When editing has been repeatedly performed, the control Information area may come up to be full even the recording area has enough space. Delete unnecessary titles (pages 51, 54). Recording Error You cannot record on this disc as Power Calibration Area is full. When recordings are performed repeatedly onto an unstable disc, this area may come up to be full. Every time you insert a disc for recording, the disc’s working area will be taken up. And if you repeat this frequently, it will be used up sooner and you may not be able to record full 99 titles. Insert a new disc. Recording Error This disc is already finalized. You are trying to record onto the disc already finalized. Release the finalizing for this disc (page 35). Language Code Abkhazian 4748 Afar 4747 Afrikaans 4752 Albanian 6563 Amharic 4759 Arabic 4764 Armenian 5471 Assamese 4765 Aymara 4771 Azerbaijani 4772 Bashkir 4847 Basque 5167 Bengali;Bangla 4860 Bhutani 5072 Bihari 4854 Bislama 4855 Breton 4864 Bulgarian 4853 Burmese 5971 Byelorussian 4851 Cambodian 5759 Catalan 4947 Chinese 7254 Corsican 4961 Croatian 5464 Czech 4965 Danish 5047 Dutch 6058 English 5160 Esperanto 5161 Estonian 5166 Faroese 5261 Fiji 5256 Finnish 5255 Language Code French 5264 Frisian 5271 Galician 5358 Georgian 5747 German 5051 Greek 5158 Greenlandic 5758 Guarani 5360 Gujarati 5367 Hausa 5447 Hebrew 5569 Hindi 5455 Hungarian 5467 Icelandic 5565 Indonesian 5560 Interlingua 5547 Interlingue 5551 Inupiak 5557 Irish 5347 Italian 5566 Japanese 5647 Javanese 5669 Kannada 5760 Kashmiri 5765 Kazakh 5757 Kinyarwanda 6469 Kirghiz 5771 Kirundi 6460 Korean 5761 Kurdish 5767 Laothian 5861 Latin 5847 Latvian; Lettish 5868 Lingala 5860 Language Code Lithuanian 5866 Macedonian 5957 Malagasy 5953 Malay 5965 Malayalam 5958 Maltese 5966 Maori 5955 Marathi 5964 Moldavian 5961 Mongolian 5960 Nauru 6047 Nepali 6051 Norwegian 6061 Occitan 6149 Oriya 6164 Oromo (Afan) 6159 Panjabi 6247 Pashto; Pushto 6265 Persian 5247 Polish 6258 Portuguese 6266 Quechua 6367 Rhaeto-Romance 6459 Romanian 6461 Russian 6467 Samoan 6559 Sangho 6553 Sanskrit 6547 Scots Gaelic 5350 Serbian 6564 Serbo-Croatian 6554 Sesotho 6566 Setswana 6660 Shona 6560 Language Code Sindhi 6550 Singhalese 6555 Siswat 6565 Slovak 6557 Slovenian 6558 Somali 6561 Spanish 5165 Sundanese 6567 Swahili 6569 Swedish 6568 Tagalog 6658 Tajik 6653 Tamil 6647 Tatar 6666 Telugu 6651 Thai 6654 Tibetan 4861 Tigrinya 6655 Tonga 6661 Tsonga 6665 Turkish 6664 Turkmen 6657 Twi 6669 Ukrainian 6757 Urdu 6764 Uzbek 6772 Vietnamese 6855 Volapuk 6861 Welsh 4971 Wolof 6961 Xhosa 7054 Yiddish 5655 Yoruba 7161 Zulu 7267

Analog audio An electrical signal that directly represents sound. Compare this to digital audio which can be an electrical signal, but is an indirect representation of sound. See also Digital audio. Aspect ratio The width of a TV screen relative to its height. Conventional TVs are 4:3 (in other words, the screen is almost square); widescreen models are 16:9 (the screen is almost twice as wide as it is high). Chapter Just as a book is split up into several chapters, a title on a DVD disc is usually divided into chapters. See also Title. Component video output Each signal of luminance(Y) and component(Pb/Cb, Pr/Cr) is independent to output so that you can experience picture color as it is. Also, due to compatibility with progressive video (525p/480p), you can experience higher-density picture than that in interlace (525i/480i). CPRM (Content Protection for Recordable Media) CPRM is a copy protection system with scramble system regarding the recording of “copy-once” broadcast programs (e.g. some satellite broadcasts). Digital audio An indirect representation of sound by numbers. During recording, the sound is measured at discrete intervals (44,100 times a second for CD audio) by an analog-to- digital converter, generating a stream of numbers. On playback, a digital-to-analog converter generates an analog signal based on these numbers. See also Sampling frequency and Analog audio. Dolby Digital The system to compress digital sound developed by Dolby Laboratories. It offers you sound of stereo(2ch) or Multi-channel audio. Finalize To make DVD discs, which have been recorded on, possible to play in DVD players. With this unit, it is possible to finalize DVD-R/DVD- RW discs. MP3 (MPEG Audio Layer 3) MP3 is a method of compressing files. You can copy MP3 files on CD-RW/R discs from the computer and play the files on this unit. PCM (Pulse Code Modulation) The most common system of encoding digital audio, found on CDs and DAT. Excellent quality, but requires a lot of data compared to formats such as Dolby Digital and MPEG audio. For compatibility with digital audio recorders (CD, MD and DAT) and AV amplifiers with digital inputs, this unit can convert Dolby Digital and MPEG audio to PCM. See also Digital audio. Playlist From this list you can play contents of a disc as your desired order or in sequence. Also it is allowed to search a specific scene directly. Progressive Scan (525p/480p) A type of display that does not split each frame into fields, and instead scans directly through all the scanlines of each frame in order. Progressive Scan provides less flickering and higher image resolution than traditional (525i/480i) TV signals. Refer to page 13 for instructions on selective Progressive Scan mode. Regions code Regions associate discs and players with particular areas of the world. This unit will only play discs that have compatible region codes. You can find the region code of your unit by looking on the rear panel. Some discs are compatible with more than one region (or all regions). Sampling frequency The rate which sound is measured by a specified interval to turn into digital audio data. The numbers of sampling in one second defines as sampling frequency. The higher the rate, the better the sound quality as possible as it is. SAP (Secondary Audio Program) Sub audio channel which is delivered separately from main- audio channel. This audio channel is used as an alternate in bilingual broadcasting. S-Video output It delivers independently each signal of color(C) and luminance(Y) to TV as video signals, so that higher-quality picture will be gained. Title (DVD only) A collection of chapters on DVD disc. See also chapter. Track Audio CDs use tracks to divide up the content of a disc. The DVD equivalent is called a chapter. See also Chapter. –– Can I record to CD-R/RW? No, this unit records only DVDs. –– Can I play DVD-Video that is bought in another country? Possible when the region code of the disc is 1 and All. –– Is this unit JPEG compatible? No. –– Can I connect the unit to my PC? No, you cannot control the unit by PCs. Glossary

Connections Getting started Others Español Specifications Changing the Setup menu General System DVD-Video, DVD-RW/R, CD-DA, CD-RW/R Power requirements AC120 V, 60 Hz Power consumption 20 W (standby: 2.8 W) Weight 5.1 lbs ( 2.3 kg ) Dimensions (width x height x depth) 17 3/16” x 2 5/8” x 9 5/8” (435 x 66 x 244 mm) Operating temperature 41Fº to 104Fº (5ºC to 40ºC) Operating humidity Less than 80% (no condensation) TV format NTSC Recording Recording format Video Recording format (DVD-RW only), Video format (DVD-RW, DVD-R) Recordable discs DVD-Rewritable, DVD-Recordable Video recording format Sampling frequency Compression format 13.5MHz MPEG Audio recording format Sampling frequency Compression format 48kHz Dolby Digital Tuner Receivable channels VHF UHF CATV 2-13ch 14-69ch C1-C125ch Input / Output VHF/UHF antenna input/output terminal VHF/UHF set 75 Video input Input level Jacks Input 1 (rear), 2 (front) 1 Vp-p (75) RCA jack Video output Output level Jack Output 1 (rear) 1 Vp-p (75) RCA jack S-Video input Y (Iuminance) - Input level C (color) - Input level Jacks Input 1 (rear), 2 (front) 1 Vp-p (75) 286 mVp-p (75) 4 pin mini DIN S-Video output Y (Iuminance) - Output level C (color) - Output level Jack Output 1 (rear) 1 Vp-p (75) 286 mVp-p (75) 4 pin mini DIN Component video output Output level Jacks Output 1 (rear) Y: 1.0 Vp-p (75), PB/CB, PR/CR: 0.7 Vp-p (75) RCA jacks Audio input During audio input Jacks Input 1 (rear), 2 (front) L/R 2V rms (Input impedance: more than 22k) RCA jacks Audio output During audio output Jacks Output 1 L/R (rear) 2V rms (Output impedance: less than 1k) RCA jacks Digital audio output Output level Jacks Output 1 (rear) COAXIAL 500 mVp-p (75) RCA jack Note: The specifications and design of this product are subject to change without notice.

Nota: Asegúrese que las pilas están en el mando a distancia y que ha conectado correctamente esta unidad y el TV. Paso 1: Elija un tipo de disco. Puede elegir entre distintos tipos de discos DVD grabables. Elija un tipo de disco DVD grabable de acuerdo con sus necesidades de reproducción/ grabación. Vea los “Tipos de discos DVD” en la parte inferior de esta página para más detalles sobre las diferencias entre los distintos medios compatibles. Este grabador de DVD puede grabar los sigu- ientes tipos de discos. Por ejemplo, cuando desea grabar repetida- mente en el mismo disco o cuando desea edi- tar el disco después de grabar, seleccione el disco de tipo regrabable DVD-RW. Cuando desea guardar grabaciones sin alter- arlos, un DVD no regrabable DVD-R puede ser más conveniente. Paso 2: Coloque un disco en blanco. POWER ZOOM DISPLAY SETUP TOP MENU MENU/LIST REC SPEED REC/OTR PAUSE SKIP SKIP PLAY CM SKIP REPEAT OPEN/CLOSE TIMER PROG. FWD REV CLEAR 1 2 3 4 5 6 7 8 9 SPACE 0 A H G ENTER CH RETURN .@/: ABC DEF GHI JKL MNO PQRS TUV WXYZ B C { B K L h g F STOP Bx1.3/0.8 POWER ZOOM DISPLAY SETUP TOP MENU MENU/LIST REC SPEED REC/OTR PAUSE SKIP SKIP PLAY CM SKIP REPEAT OPEN/CLOSE TIMER PROG. FWD REV CLEAR 1 2 3 4 5 6 7 8 9 SPACE 0 A H G ENTER CH RETURN .@/: ABC DEF GHI JKL MNO PQRS TUV WXYZ B C { B K L h g F STOP Bx1.3/0.8 Mando a distancia Para abrir Para cerrar Formato del disco Coloque el disco en el grabador. Haga el formato del disco del menú SETUP, existen los formatos de video (modo de Video) o de grabación de video (modo VR) según el tipo de disco colocado. Esto es necesario para preparar el disco para gra- bación. Vea los detalles en las páginas 26-27. * Al formatear, todo el contenido de ese disco se borrará. * La unidad empieza a formatear automáticamente cuando se inserta un disco DVD- RW no usado. Tipos de discos DVD DVD-RW VR DVD-RW Video Desea Grabar programas de TV Volver a utilizar borrando partes no deseadas Editar las grabaciones Editar/grabar de equipos conectados Copiar discos para distribución Reproducir en otro equipo de DVD *1 *1 DVD-RW VR DVD-RW Video Detalles Grabación ¿Regrabable? Sí Sí Puede crear capítulos a intervalos fijos (auto.) Sí Sí Puede crear capítulos donde desee (manual) Sí No Puede grabar imágenes de tamaño 16:9 Sí Sí Puede grabar un programa de Copia-una-vez Sí No Edición Puede hacer funciones de edición básica Sí Sí Puede hacer funciones de edición avanzadas (edición de lista a reproducir) Sí No No Sí No Sí No Sí No *1 El DVD-RW (modo VR) sólo puede reproducirse en equipos de DVD compatibles con VR. Nota: Para más detalles sobre las funciones anteriores y las limitaciones implícitas, lea las explicaciones en este manual. DVD-R DVD-R : Más adecuado : Puede utilizar : Algunas funciones son limitadas : No puede utilizar Para encender Cargando Esta operación puede demorar en reconocerse. (o) Fácil grabación de DVD 2 4 3 1

velocidad de grabación. Paso 5: Grabe en discos DVD. Español Recording Playing discs Editing Before you start Connections Getting started Others Paso 4:Seleccione el canal des eado. XP 0:58 Paso 6: Pare la grabación. CH 12 I Sugerencia 1: Reproduzca el contenido grabado Puede seleccionar el título que desea reproducir de un menú indicado y empiece a reproducir inmediatamente. El contenido grabado se puede acceder fácilmente con un simple procedimiento de elegir un título en un capítulo en la pantalla del menú. ¿Qué son títulos y capítulos? El contenido de un disco DVD se divide gen- eralmente en títulos. Los títulos pueden dividirse a su vez en capítulos. Sugerencia 2: Edite el disco grabado La edición de discos es fácil. Esta unidad ofrece convenientes funciones de edición que sólo son posibles con discos DVD-RW/R. Puede editar lo siguiente de la lista de títulos. • Poniendo nombres en títulos • Seleccionando imágenes para índices • Seleccionando/borrando marcadores de capítulos • Borrado de títulos o escenas (Las funciones editables dependen del modo de grabación y forma de edición.) Original y Playlist (modo VR) Puede editar las grabaciones en la lista a reproducir sin cambiar las grabaciones originales. Cualquier lista a reproducir no ocupa mucho espacio en el disco. ¿Qué significa “Original” o “Playlist”? A lo largo de este manual encontrará Original y Playlist que se refieren a las gra- baciones reales y la versión editada. • La grabación Original se refiere a la grabación real en el disco. • El Playlist se refiere a la versión editada del disco; cómo se va a reproducir la versión Original. Finalización de un disco • Esto permitirá que un disco que se grabe en nuestra unidad pueda ser reproducido en un reproductor DVD diferente. Un disco sin finalizar no se podrá reproducir en otro reproductor. • Después de finalizar un disco, si la grabación se hizo en el modo de vídeo, usted no podrá editar ninguna información que se encuentre en ese disco. • Si ha grabado en el modo VR en un disco DVD-RW, la edición podrá realizarse incluso después de la finalización. Track 1 Track 2 Track 3 Track 4 Track 5 Inicio de grab. Parada/inicio Parada grab. Start Rec. Stop Rec. Título 1 Título 2 Capítulo 1 Capítulo 1 Capítulo 2 Capítulo 3 Capítulo 2 Esta operación puede demorar en completarse. Escrit de datos 90% C Fácil grabación de DVD (cont.) Español Changing the Setup menu POWER ZOOM DISPLAY SETUP TOP MENU MENU/LIST REC SPEED REC/OTR PAUSE SKIP SKIP PLAY CM SKIP REPEAT OPEN/CLOSE TIMER PROG. FWD REV CLEAR 1 2 3 4 5 6 7 8 9 SPACE 0 A H G ENTER CH RETURN .@/: ABC DEF GHI JKL MNO PQRS TUV WXYZ B C { B K L h g F STOP Bx1.3/0.8 POWER ZOOM DISPLAY SETUP TOP MENU MENU/LIST REC SPEED REC/OTR PAUSE SKIP SKIP PLAY CM SKIP REPEAT OPEN/CLOSE TIMER PROG. FWD REV CLEAR 1 2 3 4 5 6 7 8 9 SPACE 0 A H G ENTER CH RETURN .@/: ABC DEF GHI JKL MNO PQRS TUV WXYZ B C { B K L h g F STOP Bx1.3/0.8 POWER ZOOM DISPLAY SETUP TOP MENU MENU/LIST REC SPEED REC/OTR PAUSE SKIP SKIP PLAY CM SKIP REPEAT OPEN/CLOSE TIMER PROG. FWD REV CLEAR 1 2 3 4 5 6 7 8 9 SPACE 0 A H G ENTER CH RETURN .@/: ABC DEF GHI JKL MNO PQRS TUV WXYZ B C { B K L h g F STOP Bx1.3/0.8 POWER ZOOM DISPLAY SETUP TOP MENU MENU/LIST REC SPEED REC/OTR PAUSE SKIP SKIP PLAY CM SKIP REPEAT OPEN/CLOSE TIMER PROG. FWD REV CLEAR 1 2 3 4 5 6 7 8 9 SPACE 0 A H G ENTER CH RETURN .@/: ABC DEF GHI JKL MNO PQRS TUV WXYZ B C { B K L h g F STOP Bx1.3/0.8

Printed in China LIMITED WARRANTY FUNAI CORP. will repair this product, free of charge in the USA in the event of defect in materials or workmanship as follows: DURATION: PARTS: FUNAI CORP. will provide parts to replace defective parts without charge for one (1) year from the date of original retail purchase. Certain parts are excluded from this warranty. LABOR: FUNAI CORP. will provide the labor without charge for a period of ninety (90) days from the date of original retail purchase. LIMITS AND EXCLUSIONS: This warranty is extended only to the original retail purchaser. A purchase receipt or other proof of original retail purchase will be required together with the product to obtain service under this warranty. This warranty shall not be extended to any other person or transferee. This warranty is void and of no effect if any serial numbers on the product are altered, replaced, defaced, missing or if service was attempted by an unauthorized service center. This limited warranty does not apply to any product not purchased and used in the United States. This product is produced for home use and this warranty only covers failures due to defects in material or workmanship which occurs during normal use. It does not cover damage which occurs in shipment, or failures which are caused by repairs, alterations or product not supplied by FUNAI CORP, or damage which results from accident, misuse, abuse, mishandling, misapplication, alteration, faulty installation, improper maintenance, commercial use such as hotel, rental or office use of this product or damage which results from fire, flood, lightning or other acts of God. THIS WARRANTY DOES NOT COVER PACKING MATERIALS, ANY ACCESSORIES (EXCEPT REMOTE CONTROL), ANY COSMETIC PARTS, COMPLETE ASSEMBLY PARTS, DEMO OR FLOOR MODELS. FUNAI CORP. AND ITS REPRESENTATIVES OR AGENTS SHALL IN NO EVENT BE LIABLE FOR ANY GENERAL, INDIRECT OR CONSEQUENTIAL DAMAGES ARISING OUT OF OR OCCASIONED BY THE USE OF OR THE INABILITY TO USE THIS PRODUCT. THIS WARRANTY IS MADE IN LIEU OF ALL OTHER WARRANTIES, EX OR IMPLIED, AND OF ALL OTHER LIABILITIES ON THE PART OF FUNAI, ALL OTHER WARRANTIES INCLUDING THE WARRANTY OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, ARE HEREBY DISCLAIMED BY FUNAI AND ITS REPRESENTATIVES IN THE UNITED STATES. ALL WARRANTY INSPECTIONS AND REPAIRS MUST BE PERFORMED BY AN AUTHORIZED SERVICE CENTER. THIS WARRANTY IS ONLY VALID WHEN THE UNIT IS CARRIED-IN TO AN AUTHORIZED SERVICE CENTER. IMPORTANT: THIS LIMITED WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS. YOU MAY HAVE OTHER RIGHTS THAT VARY FROM STATE TO STATE. IF, AT ANY TIME DURING THE WARRANTY PERIOD, YOU ARE UNABLE TO OBTAIN SATISFACTION WITH THE REPAIR OF THIS PRODUCT, PLEASE CONTACT FUNAI CORP. ATTENTION: FUNAI CORP. RESERVES THE RIGHT TO MODIFY ANY DESIGN OF THIS PRODUCT WITHOUT PRIOR NOTICE. To locate your nearest AUTHORIZED SERVICE CENTER or for general service inquires, please contact us at: FUNAI CORPORATION Customer Service Tel :1-800-605-8453 http://www.SylvaniaConsumerElectronics.com 19900 Van Ness Avenue, Torrance, CA 90501

PCM / BITSTREAM COAXIAL AUDIO IN VIDEO Video cable (supplied) Audio cable (supplied) (Back of TV) or Cable TV signal Connect Connect Connect Connect Antenna (Back of this unit) 2 1 3 4 IN OUT (Cable box or Satellite box) RF cable (not supplied) RF cable (supplied) This unit can record to DVD-R and DVD-RW discs. DVD-R discs can only be recorded to once, and cannot be erased. DVD-RW discs can be recorded to and erased many times. DVD-R discs can only be recorded in Video mode, while DVD-RW discs can select a recording format between Video mode and VR mode. 1 Connections 2 Watching TV/DVD Follow to the back side of this sheet. disc tray guide Insert a disc. POWER ZOOM DISPLAY SETUP TOP MENU MENU/LIST REC SPEED REC/OTR PAUSE SKIP SKIP PLAY CM SKIP REPEAT OPEN/CLOSE TIMER PROG. FWD REV CLEAR 1 2 3 4 5 6 7 8 9 SPACE 0 A H G ENTER CH RETURN .@/: ABC DEF GHI JKL MNO PQRS TUV WXYZ B C { B K L h g F STOP Bx1.3/0.8 This unit is compatible to play the following discs. Disc type Functions DVD-RW: 1-4x DVD-R: 2x.4x.8x DVD-RW DVD-RW VR DVD-RW DVD-RW Video DVD-R DVD-R Attributes 8cm/12cm, single-sided, single layer disc Approx. max. recording time (SEP mode): 600 minutes (4.7GB) (for 12cm) 180 minutes (1.4GB) (for 8cm) 8cm/12cm, single-sided, single layer disc Approx. max. recording time (SEP mode): 600 minutes (4.7GB) (for 12cm) 180 minutes (1.4GB) (for 8cm) Playing, limited recording, limited editing Playing, limited recording, limited editing Playing, recording, Original/Playlist editing Disc format Video mode VR mode Video mode Logo Disc Logo Disc DVD-VIDEO DVD-RW (VIDEO/VR mode) DVD-R (VIDEO mode) CD-DA (AUDIO CD) CD-R (CD-DA FORMAT, MP3 files) CD-RW (CD-DA FORMAT, MP3 files) The number inside the globe refers to region of the world. This unit can play DVDs that are labeled for ALL regions or for Region 1. DVR90DG 2 – 1 DVD Playback 2 – 2 Initial Setting Press [POWER] to turn the unit on. Press [OPEN/CLOSE] to open the disc tray. After you have completed connections; Press the input selector button (usually TV/VIDEO, INPUT or AUX) on your TV to switch an appropriate external input channel (usually near channel 0) for viewing the picture from this unit. Please refer to “Input Mode Names for Common TV Brands” on page 15 of the Owner's manual or the manual accompanying your TV. DVD Recorder Playable discs Region codes Recordable discs 1 DVR90DG DVD Recorder is a trademark of DVD Format/Logo Licensing Corporation. I Both A/V and RF cables must be connected to the TV for operation. I See front page of the Owner's Manual for the connection with the RF modulator. 1. Turn on the TV and the unit in the first time. “Initial Setting” will appear. Using [K / L], select your desired language for OSD. Then press [ENTER] to go to next step. 2. Press [ENTER] to Channel Preset. The unit will start getting channels available in your area. I DVD+R/+RW discs can be played back only on this unit. 3. Clock Setting menu will appear. Press [ENTER], default date will appear. Initial Setting Français Español English Auto Presetting Now CH 1 4. Using [K / L], enter the date (month / day / year). Press [{ / B] to move the cursor. FEB/ 01 / 2006(WED) 12: 00 AM Initial Setting JAN/ 01 / 2006(SUN) 12: 00 AM Initial Setting 5. Using [K / L], enter the time (hour / minute). Press [{ / B]. A cursor will move on AM or PM. 6. Press [K / L] to select “AM” or “PM”. Press [ENTER]. TV Program will automatically appear. (Usually near channel 0) Playing, recording, and editing discs are available on this unit. FEB/ 01 / 2006(WED) 12: 00 AM Initial Setting

Set the date. Set start and end time. Timer Programming 2. --- 3. --- 4. --- 5. --- 6. --- 7. --- 8. --- 1. JAN/01 12:57AM --:-- L1 Date Start End CH Speed Select the channel number to record. Timer Programming 2. --- 3. --- 4. --- 5. --- 6. --- 7. --- 8. --- 1. JAN/01 12:57AM 1:57AM CH8 Date Start End CH Speed Select the recording speed. Timer Programming 2. --- 3. --- 4. --- 5. --- 6. --- 7. --- 8. --- 1. JAN/01 12:57AM 1:57AM CH8 1H Date Start End CH Speed ENTER 3 – 2 Timer Recording After all recordings, finalize your disc. After recording, you must finalize the disc in order to play on other units. This Unit DVD player Not Playable Playable REC/OTR REC SPEED OPEN/CLOSE CHANNEL REV FWD STOP PLAY POWER S-VIDEO VIDEO AUDIO L R Select the recording speed. POWER ZOOM DISPLAY SETUP TOP MENU MENU/LIST REC SPEED REC/OTR PAUSE SKIP SKIP PLAY CM SKIP REPEAT OPEN/CLOSE TIMER PROG. FWD REV CLEAR 1 2 3 4 5 6 7 8 9 SPACE 0 A H G ENTER CH RETURN .@/: ABC DEF GHI JKL MNO PQRS TUV WXYZ B C { B K L h g F STOP Bx1.3/0.8 Record on DVD disc. POWER ZOOM DISPLAY SETUP TOP MENU MENU/LIST REC SPEED REC/OTR PAUSE SKIP SKIP PLAY CM SKIP REPEAT OPEN/CLOSE TIMER PROG. FWD REV CLEAR 1 2 3 4 5 6 7 8 9 SPACE 0 A H G ENTER CH RETURN .@/: ABC DEF GHI JKL MNO PQRS TUV WXYZ B C { B K L h g F STOP Bx1.3/0.8 Select the desired channel. POWER ZOOM DISPLAY SETUP TOP MENU MENU/LIST REC SPEED REC/OTR PAUSE SKIP SKIP PLAY CM SKIP REPEAT OPEN/CLOSE TIMER PROG. FWD REV CLEAR 1 2 3 4 5 6 7 8 9 SPACE 0 A H G ENTER CH RETURN .@/: ABC DEF GHI JKL MNO PQRS TUV WXYZ B C { B K L h g F STOP Bx1.3/0.8 Stop the recording. POWER ZOOM DISPLAY SETUP TOP MENU MENU/LIST REC SPEED REC/OTR PAUSE SKIP SKIP PLAY CM SKIP REPEAT OPEN/CLOSE TIMER PROG. FWD REV CLEAR 1 2 3 4 5 6 7 8 9 SPACE 0 A H G ENTER CH RETURN .@/: ABC DEF GHI JKL MNO PQRS TUV WXYZ B C { B K L h g F STOP Bx1.3/0.8 Press [TIMER PROG.]. POWER ZOOM DISPLAY SETUP TOP MENU MENU/LIST REC SPEED REC/OTR PAUSE SKIP SKIP PLAY CM SKIP REPEAT OPEN/CLOSE TIMER PROG. FWD REV CLEAR 1 2 3 4 5 6 7 8 9 SPACE 0 A H G ENTER CH RETURN .@/: ABC DEF GHI JKL MNO PQRS TUV WXYZ B C { B K L h g F STOP Bx1.3/0.8 • You can set up to 8 programs (once, daily or weekly). • Be sure to set the clock before starting a timer programming. Timer Programming list appears. Select any blank line with [K / L] and press [ENTER]. POWER ZOOM DISPLAY SETUP TOP MENU MENU/LIST REC SPEED REC/OTR PAUSE SKIP SKIP PLAY CM SKIP REPEAT OPEN/CLOSE TIMER PROG. FWD REV CLEAR 1 2 3 4 5 6 7 8 9 SPACE 0 A H G ENTER CH RETURN .@/: ABC DEF GHI JKL MNO PQRS TUV WXYZ B C { B K L h g F STOP Bx1.3/0.8 Timer Programming 2. --- 3. --- 4. --- 5. --- 6. --- 7. --- 8. --- 1. --- Date Start End CH Speed Move to next Move to next POWER ZOOM DISPLAY SETUP TOP MENU MENU/LIST REC SPEED REC/OTR PAUSE SKIP SKIP PLAY CM SKIP REPEAT OPEN/CLOSE TIMER PROG. FWD REV CLEAR 1 2 3 4 5 6 7 8 9 SPACE 0 A H G ENTER CH RETURN .@/: ABC DEF GHI JKL MNO PQRS TUV WXYZ B C { B K L h g F STOP Bx1.3/0.8 Move to next POWER ZOOM DISPLAY SETUP TOP MENU MENU/LIST REC SPEED REC/OTR PAUSE SKIP SKIP PLAY CM SKIP REPEAT OPEN/CLOSE TIMER PROG. FWD REV CLEAR 1 2 3 4 5 6 7 8 9 SPACE 0 A H G ENTER CH RETURN .@/: ABC DEF GHI JKL MNO PQRS TUV WXYZ B C { B K L h g F STOP Bx1.3/0.8 POWER ZOOM DISPLAY SETUP TOP MENU MENU/LIST REC SPEED REC/OTR PAUSE SKIP SKIP PLAY CM SKIP REPEAT OPEN/CLOSE TIMER PROG. FWD REV CLEAR 1 2 3 4 5 6 7 8 9 SPACE 0 A H G ENTER CH RETURN .@/: ABC DEF GHI JKL MNO PQRS TUV WXYZ B C { B K L h g F STOP Bx1.3/0.8 POWER ZOOM DISPLAY SETUP TOP MENU MENU/LIST REC SPEED REC/OTR PAUSE SKIP SKIP PLAY CM SKIP REPEAT OPEN/CLOSE TIMER PROG. FWD REV CLEAR 1 2 3 4 5 6 7 8 9 SPACE 0 A H G ENTER CH RETURN .@/: ABC DEF GHI JKL MNO PQRS TUV WXYZ B C { B K L h g F STOP Bx1.3/0.8 POWER ZOOM DISPLAY SETUP TOP MENU MENU/LIST REC SPEED REC/OTR PAUSE SKIP SKIP PLAY CM SKIP REPEAT OPEN/CLOSE TIMER PROG. FWD REV CLEAR 1 2 3 4 5 6 7 8 9 SPACE 0 A H G ENTER CH RETURN .@/: ABC DEF GHI JKL MNO PQRS TUV WXYZ B C { B K L h g F STOP Bx1.3/0.8 POWER ZOOM DISPLAY SETUP TOP MENU MENU/LIST REC SPEED REC/OTR PAUSE SKIP SKIP PLAY CM SKIP REPEAT OPEN/CLOSE TIMER PROG. FWD REV CLEAR 1 2 3 4 5 6 7 8 9 SPACE 0 A H G ENTER CH RETURN .@/: ABC DEF GHI JKL MNO PQRS TUV WXYZ B C { B K L h g F STOP Bx1.3/0.8 POWER ZOOM DISPLAY SETUP TOP MENU MENU/LIST REC SPEED REC/OTR PAUSE SKIP SKIP PLAY CM SKIP REPEAT OPEN/CLOSE TIMER PROG. FWD REV CLEAR 1 2 3 4 5 6 7 8 9 SPACE 0 A H G ENTER CH RETURN .@/: ABC DEF GHI JKL MNO PQRS TUV WXYZ B C { B K L h g F STOP Bx1.3/0.8 1VMN21673 / E7A00UD_QG ★★★★★ Recording times appear on the TV screen (30 minutes to 8 hours). Recording will start. When the unit reaches the specified time, recording will stop automatically. Set the Timer Standby mode How to select the recording speed: Recording speed XP (1H) SP (2H) LP (4H) EP (6H) SLP (8H) SEP (10H) Recording time 18 min 36 min 72 min 108 min 144 min 180 min Video/Sound Quality Disc Size 8cm Disc XP (1H) SP (2H) LP (4H) EP (6H) SLP (8H) SEP (10H) 60 min 120 min 240 min 360 min 480 min 600 min 12cm Disc (poor) (poor) (good) (good) 3 – 1 Easy Recording 3 DVD Recording POWER ZOOM DISPLAY SETUP TOP MENU MENU/LIST REC SPEED REC/OTR PAUSE SKIP SKIP PLAY CM SKIP REPEAT OPEN/CLOSE TIMER PROG. FWD REV CLEAR 1 2 3 4 5 6 7 8 9 SPACE 0 A H G ENTER CH RETURN .@/: ABC DEF GHI JKL MNO PQRS TUV WXYZ B C { B K L h g F STOP Bx1.3/0.8 Daily MON-SAT JAN/01 JAN/31 MON-FRI SAT FRI SUN L L L L L L L L Timer Programming 2. --- 3. --- 4. --- 5. --- 6. --- 7. --- 8. --- 1. JAN/01 --:-- --:-- L1 Date Start End CH Speed POWER ZOOM DISPLAY SETUP TOP MENU MENU/LIST REC SPEED REC/OTR PAUSE SKIP SKIP PLAY CM SKIP REPEAT OPEN/CLOSE TIMER PROG. FWD REV CLEAR 1 2 3 4 5 6 7 8 9 SPACE 0 A H G ENTER CH RETURN .@/: ABC DEF GHI JKL MNO PQRS TUV WXYZ B C { B K L h g F STOP Bx1.3/0.8 POWER ZOOM DISPLAY SETUP TOP MENU MENU/LIST REC SPEED REC/OTR PAUSE SKIP SKIP PLAY CM SKIP REPEAT OPEN/CLOSE TIMER PROG. FWD REV CLEAR 1 2 3 4 5 6 7 8 9 SPACE 0 A H G ENTER CH RETURN .@/: ABC DEF GHI JKL MNO PQRS TUV WXYZ B C { B K L h g F STOP Bx1.3/0.8 Turn the unit off. Timer Recording is now set. I Formatting is not needed when inserting a blank disc. UNIT AUTOMATICALLY PREPARES THE DISC FOR RECORDING. I For playback on other DVD players, be sure to record on Video mode and to finalize the disc once recording is finished. OTHER PLAYER MUST PLAY BACK DVD-R or DVD-RW. Hints for DVD Recording 0:30 (Normal Recording) 8:00 7:30 1:00 I 0:30 When pressing POWER ZOOM DISPLAY SETUP TOP MENU MENU/LIST REC SPEED REC/OTR PAUSE SKIP SKIP PLAY CM SKIP REPEAT OPEN/CLOSE TIMER PROG. FWD REV CLEAR 1 2 3 4 5 6 7 8 9 SPACE 0 A H G ENTER CH RETURN .@/: ABC DEF GHI JKL MNO PQRS TUV WXYZ B C { B K L h g F STOP Bx1.3/0.8 at the current date, Timer Recording mode will change as follows: e.g. January 1st at present indicator will appear on the front panel display.