Fiber Options S703V Instruction Manual

This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used properly in strict accordance with the instructions contained herein, may cause interference to radio communication. It has been tested and found to comply with the limits for Class A computing devices in accordance with the spec- ifications found in Subpart J of Part 15 of FCC rules, which are designed to provide reasonable protection against such interference when the equipment is operated in a commercial environment. Operation of this equipment in a residential area is likely to cause interference, in which case the user will be required to take whatev- er means may be necessary to correct the interference at his own expense. Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This apparatus does not exceed the Class A limits for radio noise emission set out in the Radio Interference Regulation of Industry of Canada. Cet appareil numérique de la Classe A respecte toutes les exigences du Règlement sur le matériel brouilleur du Canada. Federal Communications Commission and Industry Canada Radio Frequency Interference Statements FCC PART 15 COMPLIANT

1 INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 1.1 INSTALLATION CONSIDERATIONS. . . . . . . . . . . . .1 1.2 STANDALONE MODULES . . . . . . . . . . . . . . . . . . . .1 1.3 RACK CARDS . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 1.3.1 515R1 AND 517R1 CARD CAGES . . . . . . . . . . .1 1.3.2 501R ENCLOSURES . . . . . . . . . . . . . . . . . . . . .1 2 SIGNAL CONNECTIONS . . . . . . . . . . . . . . . . . . . . . . . .2 3 OPTICAL CONNECTIONS . . . . . . . . . . . . . . . . . . . . . . .2 4 ELECTRICAL CONNECTIONS . . . . . . . . . . . . . . . . . . . .2 4.1 RACKMOUNT CARDS . . . . . . . . . . . . . . . . . . . . . . .2 4.2 STANDALONE MODULES . . . . . . . . . . . . . . . . . . . .2 5 TROUBLESHOOTING . . . . . . . . . . . . . . . . . . . . . . . . . .2 6 CONTACTING FIBER OPTIONS . . . . . . . . . . . . . . . . . .2 7 SHIPPING AND PACKING . . . . . . . . . . . . . . . . . . . . . . .2 8 RETURNS TO FIBER OPTIONS . . . . . . . . . . . . . . . . . .2 Contents Figures & Tables FIGURE 1: STANDALONE TRANSMITTER . . . . . . . . . . . .ii FIGURE 2: 501R ENCLOSURE . . . . . . . . . . . . . . . . . . . .ii FIGURE 3: SYSTEM DIAGRAM . . . . . . . . . . . . . . . . . . . .1 FIGURE 4: S703V RACK CARD . . . . . . . . . . . . . . . . . . . .3 FIGURE 5: RACK CARD FRONT BEZELS . . . . . . . . . . . .3 FIGURE 6: RACK CARD CONNECTIONS . . . . . . . . . . . . .3 TABLE 1: POWER CONNECTION STANDALONE MODULE . . . . . . . . . . . . . . . . . . . .ii TABLE 2: POWER CONNECTION 502R ENCLOSURE . . . . . . . . . . . . . . . . . . . . . . . .ii TABLE 3: TRANSMITTER LED DIAGNOSTIC . . . . . . . . . . INDICATORS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4 TABLE 4: RECEIVER LED DIAGNOSTIC . . . . . . . . . . . . . INDICATORS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4

S703V & S7703V Instruction Manual ii TABLE 2: POWER CONNECTION 501R ENCLOSURE TABLE 1: POWER CONNECTION STANDALONE TRANSMITTER FIGURE 1: STANDALONE TRANSMITTER FIGURE 2: 501R ENCLOSURE PIN CONNECTION 1 12 – 16 VAC +12 – 16 VDC 2 DC Ground 3 12 – 16 VAC PIN CONNECTION 3 +13.5 – 16 VDC 2 ALARM / +5 VDC 1 Ground

S703V and S7703V series fiber optic two-channel video multi- plexer systems. Please read the entire manual before installing the equipment. These two-channel video multiplexers offer simultaneous trans- mission of two full-frame video signals (color or monochrome). The S703V units use multimode fiber while the S7703V units operate over single-mode fiber. Note: The series numbers S703VT and S703VR will be used to describe all models of transmitters and receivers unless noted otherwise. A complete system consists of a transmitter, S703VT, and a receiver, S703VR. Units are designed for standalone operation or for installation in Fiber Options’ 515R1 or 517R1 Card Cages or 501R miniature enclosures. The S703VT transmitter has two video inputs and one fiber output. The S703VR receiv- er unit has one fiber input and two video outputs. Unpacking the Unit In the event that anything is missing from the following list, con- tact your authorized Fiber Options dealer or representative. S703VT Transmitter or S703VR Receiver (S7703VT or S7703VR) Instruction manual Save the original packing materials in case it becomes neces- sary to return the unit. FIGURE 3: SYSTEM DIAGRAM one optical fiber two video inputs two video outputs S703V-T S703V-R 1 INSTALLATION 1.1 INSTALLATION CONSIDERATIONS This fiber-optic link is supplied in two forms, as a stand- alone module and as a rack card. Units should be installed in dry locations protected from extremes of tem- perature and humidity. 1.2 STANDALONE MODULES Determine where the module is to be installed and ensure that there is adequate space at both ends for making the various cable connections and for reading the diagnostic LEDs. Standalone modules are provided with mounting holes for four No. 6 screws (3-mm or 3.5-mm screws). The type of screw chosen must be suitable for the surface on which the module is to be mounted. Some standalone modules consist of a rack card installed in a standalone enclosure and are mounted in the same manner. The rack card is normally installed in the enclosure at the factory. 1.3 RACK CARDS: Rack cards are designed to be installed in one of Fiber Options’ 19-inch (483-mm) EIA standard card-cage racks, either the 515R1 or the 517R1. They may also be supplied in the 501R standalone rack-card enclosures. 1.3.1 515R1 AND 517R1 CARD CAGE RACKS To install rack cards in a rack, follow these steps: CAUTION: Fiber Options recommends that the power switch on the rack power supply be turned OFF and that the rack power supply is disconnected from any power source. Make sure that the card is oriented right-side up, and slide it into the card guides in the rack until the edge con- nector at the back of the card seats in the corresponding slot in the rack’s connector panel. Seating may require thumb pressure on the top and bottom of the card’s front panel. CAUTION: Take care not to press on any of the LEDs. Tighten the two thumb screws on the card until the front panel of the card is seated against the front of the rack. 1.3.2 501R STANDALONE ENCLOSURES To install rack cards in standalone enclosures, follow these steps: CAUTION: The rack card module can ONLY be powered by 13.5-16 VDC. AC power must not be used. S703V AND S7703V: TWO-CHANNEL VIDEO MULTIPLEXERS continued on page 2

2 CAUTION: Fiber Options recommends that the enclosure not be connected to any power source during installation. Look inside the enclosure to determine the location of the socket for the edge connector on the card. Orient the card so that it will seat in the socket, and slide it into the enclosure until the edge connector at the back of the card seats in the socket. Seating may require thumb pressure on the ends of the card’s front panel. CAUTION: Take care not to press on any of the LEDs. Tighten the two thumb screws on the card until the front panel of the card is seated against the front of the rack. 2 SIGNAL CONNECTIONS All fiber-optic links convert electrical signals of some type or types into a light signal at the transmitter and convert the light back to electrical signals for output at the receiv- er. These electrical signal connections to the S703V series consist of two BNC connectors on the transmitter and receiver. CAUTION: Make sure all peripheral equipment that is to be connected to the fiber unit is turned OFF during instal- lation. NOTE: Fiber Options recommends using Belden 9259 RG59/U coaxial cable between the video equipment and the fiber units. For best image, do not exceed the cable manufacturer’s recommendation for maximum distance. NOTE: Coaxial cable must be terminated with female BNC connectors to properly couple with the Fiber Options equipment. Connect two video sources, such as cameras, to the S703VT transmitter using terminated coaxial cables. Connect monitoring equipment to the S703VR receiver with terminated coaxial cables. 3 OPTICAL CONNECTIONS The standard optical connector on Fiber Options’ units is the ST type. Connect the pre-terminated fiber to the two fiber units. 4 ELECTRICAL CONNECTION 4.1 RACKMOUNT CARDS Make sure the power switch of the power supply is OFF, and plug the supplied power cord into a suitable outlet. Press the power switch to apply power to the modules in the rack. 4.2 STANDALONE MODULES 1. Identify the power connector and remove it from the module. 2. Make sure the power supply is not connected to any power source, and strip approximately 0.25-in (6-mm) of insulation from the ends of the cable. 3. Taking care to observe correct polarization of the cable (see table 1 for standalone transmitter modules, table 2 for 501R standalones), insert one lead into one of the screw sockets and tighten the screw. Repeat for the other conductor. Confirm the security of the con- nection by a light pull on the cable. 4. Seat the connector in its position in the fiber unit. 5. Plug the power supply into a suitable outlet. CAUTION: The rack card module can ONLY be powered by 13.5-16 VDC. AC power must not be used. Power up the peripheral equipment and verify system operation by observing video on the monitor at the receiver end. If the system does not perform as expect- ed, refer to Tables 3 and 4 for an explanation of how to diagnose system faults using the LEDs built into the Fiber Options units. 5 TROUBLESHOOTING Refer to Tables 3 and 4 for LED system diagnostic infor- mation. 6 CONTACTING FIBER OPTIONS For technical assistance in the U.S. or Canada, call the Fiber Options Headquarters in Bohemia, NY. If you are outside the U.S. or Canada, call the closest international office as listed on the back page of this manual. Have the following information available: exact model number of your fiber-optic links, and a listing of the diag- nostic indicators and their respective color or condition. 7 SHIPPING AND PACKAGING Before shipping or transporting your Fiber Options unit, pack it securely to prevent damage that could occur in transit. Take care to protect all connectors, LEDs, and corners from possible damage. 8 RETURNS TO FIBER OPTIONS If any equipment must be returned to Fiber Options for repair or replacement, you must obtain authorization from our Return Authorization department before ship- ping the unit. NOTE: Fiber Options will not accept return delivery of any products without prior authorization. Call Fiber Options at 631-567-8320 or 800-342-3748 and ask to speak to a Return Authorizations representative. You will be given full instructions for returning your prod- uct at that time. NOTE: All authorized returns must be clearly marked with the Return Authorization information. Please follow the instructions completely. continued from page 1

Fiber Options 3 FIGURE 4: S703V RACK CARD VIDEO IN VIDEO IN 703-T VIDEO IN 7703-T VIDEO IN VIDEO OUT 703-R LVL/LOSS VIDEO OUT VIDEO OUT 7703-R LVL/LOSS VIDEO OUT FIGURE 5: RACK CARD FRONT BEZELS, TRANSMITTER (LEFT) AND RECEIVER (RIGHT) FIGURE 6: RACK CARD CONNECTIONS, TRANSMITTER (LEFT) AND RECEIVER (RIGHT)

All specifications are subject to change without notice. Information furnished by FIBER OPTIONS is believed to be accurate and reliable. However, no responsibility or liability is assumed by FIBER OPTIONS for its use, nor for any infringement of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or other rights of FIBER OPTIONS. 11-0703VA Copyright 2001 by FIBER OPTIONS. All rights reserved. 010822 www.fiberoptions.com 80 Orville Drive, Bohemia NY 11716-2533 [email protected] US Tel: 631-567-8320 Fax: 631-567-8322 800-342-3748 877-FiberFax (877-342-3732) UK Tel: +44 113 238 1668 Fax: +44 113 253 8121 Australia Tel: +61 3 9370 9192 Fax: +61 3 9370 9936 France Tel: +33 01 60 86 54 53 Fax: +33 01 60 86 86 04 Germany Tel: +49 700 34237678 Fax: +49 36256 21991 Hong Kong Tel: +852 2907 8108 Fax: +852 2142 5063 Latin America Tel: 800-342-3748 Fax: 877-342-3732 TABLE 4: RECEIVER LED DIAGNOSTIC INDICATORS LED NAME COLOR INDICATION / CORRECTIVE ACTION LVL/ Green Sufficient optical power received. No action required. LOSSTM Red Insufficient optical power received. Verify fiber connected & within optical budget, receiver power on. VIDEO Green Video signal received from transmitter and video output functioning normally. No action required.* OUT Red Video output not functioning. Verify video source is connected & operating at transmitting end of link. TABLE 3: TRANSMITTER LED DIAGNOSTIC INDICATORS LED NAME COLOR INDICATION / CORRECTIVE ACTION VIDEO Green Sufficient video signal received. No action required.* IN Red Insufficient video signal received. Verify video source is connected & operating. * NOTE: A blank monitor screen may be valid video. * NOTE: A blank monitor screen may be valid video. . . . light years ahead™