Beam iridium SatDOCK 9555 Installation & User Manual

29 Bluetooth® Phone Call – Mobile Terminating 1. Ensure that the Bluetooth® audio headset is connected with the PotsDOCK, i.e. the Bluetooth® LED is turned on in BLUE - half intensity. 2. Answer the incoming call by: ♦♦Pressing the Bluetooth® headset answer button OR: ♦♦Pressing the GREEN key on the 9555 keypad. 3. To end the call: ♦♦Pressing the Bluetooth® headset answer button OR: ♦♦Pressing the RED key on the 9555 keypad. Once the call is in progress, Option A from “A Bluetooth® Phone Call – Mobile Originating” secion o ...

11 POTSDOCK 9555 KEY FEATURES POTSDOCK CRADLE • Securely holds 9555 handset • Robust design and construction • Charges 9555 handset ready for use • Integrated antenna connection • Integrated USB connectivity POTS/RJ11 • Supports standard cordless & corded telephones (5 REN) • The POTS phone can be run 600m (2000 ft) from unit • Easily integrated to PBX system • Ring, busy & dial tones • Superior voice quality TRACKING/GPS • In-built GPS engine • Tracking & alert monitoring capable • Periodic position reports or remotely polled ...

PotsDOCK has an in-built GPS module that can provide simple tracking, monitoring and alert management in various land and sea based applications within various types of vehicles, vessels or fixed site locations. The GPS module provides pinpoint accuracy and enables tracking worldwide. The tracking function has to be configured and enabled on the PotsDOCK via the PDMS. Once turned on, tracking and alert messages can be sent to a phone number, e-mail address, LeoTrak-Online or any other tracking application via SMS or Short Burst Data (SBD) if configured on the 955 ...

7 Placing Voice Calls 27 RJ11 POTS Phone Call – Mobile Originating 27 RJ11 POTS Phone Call – Mobile Terminating 28 A Bluetooth® Phone Call - Mobile Originating 28 Bluetooth® Phone Call – Mobile Terminating 29 Privacy Handset Use 29 Mute & Earpiece-Jack Mode 30 Mute functionality 30 Ringer Selection 30 Earpiece-Jack Mode 31 Tracking & Alert Operation 31 Enable Tracking & Alert 31 Send Tracking position 31 Activate Alert Mode 32 Clearing an Alert 32 PotsDOCK Front Panel 33 Data Communications 34 Using the USB Data Port 34 USB Driver Installation 3 ...

21 Preliminary Testing Prepare the Iridium 9555 Handset 1. Ensure that the 9555 Handset is running with the required compatible firmware which can be located at: www.beamcommunications.com/support/potsdock9555 2. Remove the rubber plug / bung / grommet from the rear of the 9555 Handset, to reveal the antenna socket hole. Connect Power Once all the components are installed, apply power to the PotsDOCK via the 4-way Microfit connector using the AC/DC power adaptor or the DC power cable. A: Power from the AC/DC Adaptor If the PotsDOCK is used inside a buil ...

The antenna connections exits from the rear of the PotsDOCK cradle, via the antenna loom as shown in the picture. Install the Iridium antenna in the appropriate location (with clear sky view) and then connect it to the TNC female connector on the antenna cable coming from the rear of the PotsDOCK. GPS Antenna Connection (Optional) The GPS connection is optional if the tracking function is not required. If connected, and tracking is enabled, position or location information will be shown on your tracking messages and alert messages. The GPS connection supports an a ...

43 Cradle Mounting Dimensions PotsDOCK Dimensions in millimeters 23.01 30.17 5.53 19.05 19.05 15.08 61.92 46.05 ...