iLive ITP231B Operation & User’s Manual

ITP231B 2.1 Speaker Bar for Any TV

are recyclable and should be recycled or disposed of in normal household waste. Contact your local government for disposal or recycling practices in your area. They should never be incinerated since they might explode. WARNING: Shock hazard - Do Not Open. AVIS: RISQUE DE CHOC ÉLECTRIQUE - NE PAS OUVRIR Mains Plug or Direct plug-in adapter is used as disconnect device and it should remain readily operable during intended use. In order to disconnect the apparatus from the mains completely, the Mains Plug or Direct plug-in adapter should be disconnected from the mains socket outlet completely. La fiche d’alimentation ou adaptateur de courant est utilisé comme dispositif de déconnexion et doit rester accessible pendant l’utilisation. Pour mettre l’appareil hors tension, la fiche ou adaptateur de courant doit être débranché de la prise de courant. Do not mix old and new batteries. Do not mix alkaline, standard (carbon-zinc), or rechargeable (ni-cad, ni-mh, etc) batteries. No mezcle baterías viejas y nuevas. No mezcle baterías alcalinas, estándar (carbono-zinc) o recargables (ni-cad, ni-mh, etc.). CAUTION: TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE SLOT, FULLY INSERT. WARNING: To reduce the risk of fire or electric shock, do not expose this apparatus to rain or moisture. AVERTISSEMENT: Pour réduire le risque d’incendie ou de choc électrique, ne pas exposer cet appareil sous la pluie et l’humidité. CAUTION: Use of any controls or adjustments or performance of procedures other than those herein specified may result in hazardous radiation exposure. WARNING: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. WARNING: Do not place the unit on top of any soft, porous, or sensitive surfaces to avoid damaging the surface. Use a protective barrier between the unit and surface to protect the surface. WARNING: Use of this unit near fluorescent lighting may cause interference regarding use of the remote. If the unit is displaying erratic behavior move away from any fluorescent lighting, as it may be the cause. CAUTION: Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type. PRÉCAUTION: Danger d’explosion si les piles sont remplacées de façon incorrect. Remplacer les piles seulement par le même type de pile ou l’équivalent. WARNING: There is a danger of explosion if you attempt to charge standard Alkaline batteries in the unit. Only use rechargeable NiMH batteries. WARNING: The battery, batteries, and battery pack shall not be exposed to excessive heat such as sunshine, fire, or the like. The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. WARNING: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER- SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. ATTENTION RISQUE D' ÉLECTROCUTION NE PAS OUVRIR CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. Warnings and Precautions

iLive 3 13. Unplug this apparatus during lightning storms or when unused for long periods of time. 14. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped. 1. Read these Instructions. 2. Keep these Instructions. 3. Heed all Warnings. 4. Follow all instructions. 5. Do not use this apparatus near water. 6. Clean only with a dry cloth. 7. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions. 8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat. 9. Do not defeat the safety purpose of the polarized or grounding - type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. When the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet. 10. Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus. 11. Only use attachments/accessories specified by the manufacturer. 12. This symbol indicates that this product incorporates double insulation between hazardous mains voltage and user accessible parts. Use only with a cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over. Important Safety Instructions Special note: When placing your unit on a lacquered or natural finish, protect your furniture with a cloth or other protective material. WARNING: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: • Reorient or relocate the receiving antenna. • Increase the separation between the equipment and receiver. • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. • Consult the dealer or an experienced radio/TV technician for help. The apparatus shall not be exposed to dripping or splashing and that no objects filled with liquids, such as vases, shall be placed on apparatus. L’appareil ne doit pas être exposé aux écoulements ou aux éclaboussures et aucun objet ne contenant de liquide, tel qu’un vase, ne doit être placé sur l’objet. Battery shall not be exposed to excessive heat such as sunshine, fire or the like. Les piles ne doivent pas être exposées à de forte chaleur, tel qu’à la lumière du soleil, au feu ou autres choses de semblable. Caution marking is located at the rear or back of the apparatus. Attention marquage est situé à l’arrière ou à l’arrière de l’appareil The marking information is located at the rear or back of apparatus. Les informations de marquage est situé à l’arrière ou à l’arrière de l’appareil. FCC Warnings Additional Warnings

• Powered 2.1 channel speaker system with built-in subwoofer • Motorized dock plays & charges iPod & iPhone • FM radio with 20 station presets • RCA audio input • 3.5mm Audio Input • Composite video input • Composite video output • Component video output • Subwoofer output • Advanced remote control • 37” length • Wall mountable • Treble & bass controls • 5 EQ presets • Digital clock • Wake to iPod/iPhone or radio • Gradual wake • Sleep timer • AC power: built-in AC power cord • Remote control: requires 2 AAA batteries (included) • Docking brackets for iPhone/ iPod (5) • AV cable (RCA) • Wall-mount hardware Features Includes Setup AC power: built-in AC power cable Requires 2 AAA batteries (included) Power Remote

iLive 5 Table of Contents Warnings and Precautions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Important Safety Instructions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 2.1 Speaker Bar for Any TV. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Setup. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Table of Contents. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Introduction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 iPod and iPhone. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 FM Radio . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Clock, Alarm, and Sleep Timer. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Audio Inputs and Subwoofer Output. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Basic Connectivity. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 Video Inputs and Video Output . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 Mounting to a Wall. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 Company Information. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

speaker off or on. VOLUME Press to adjust the volume. SOURCE Press to switch between iPod, Tuner, Line, and AV modes. PLAY/PAUSE Press to play or pause a docked iPhone or iPod. iPod DRAWER Press to open and close the iPod docking drawer. LINE INPUT (3.5mm) Use to connect an MP3 player or other audio source to the bar speaker. RCA AUDIO INPUT AC POWER CABLE RESET Press using a paperclip or like object to reset the bar speaker to it’s original settings. FM ANTENNA SUBWOOFER OUTPUT COMPOSITE VIDEO INPUT COMPOSITE VIDEO OUTPUT COMPONENT VIDEO OUTPUT Introduction

iLive 7 VIDEO MUTE Press to mute the volume. ALARM With the power off, press to set the alarm. CLOCK With the power off, press to set the clock. SLEEP Press repeatedly to set the sleep timer. VIDEO Press to switch between Component and Composite video output modes. BASS With the EQ set to FLAT, press to adjust the levels of bass. REV/FWD/MIN/HR Press to rewind or fast forward a docked iPhone or iPod. Press to adjust the hour and minute when setting the clock or alarm. MENU Press skip through menus on a docked iPhone or iPod. TUN/SKIP Press to skip between tracks on a docked iPhone or iPod. Press to tune the radio. ALBUM/CHAPTER/PLAYLIST Press to skip through albums, chapters, or playlists on a docked iPhone or iPod. SOURCE Press to switch between iPod, Tuner, Line, and AV modes. NUMBER KEYPAD REPEAT Press to repeat a single track or entire album on a docked iPhone or iPod. TREBLE With the EQ set to FLAT, press to adjust the levels of treble. MENU UP/DN Press to navigate up and down in menus on a docked iPhone or iPod. SELECT Press to make selections on a docked iPhone or iPod. SHUFFLE Press to play songs from a docked iPhone or iPod in a random order. EQ Press to adjust the EQ. VOLUME Press to adjust the volume. PLAY/PAUSE Press to play or pause a docked iPhone or iPod. STOP Press to stop a docked iPhone or iPod during play. MEMORY Press to cycle through saved radio stations. iPod Press to switch to iPhone/ iPod mode. STANDBY/ON Press to turn the bar speaker off or on. DISPLAY Press to view the clock on the display. iPod DRAWER Press to open or close the motorized dock for iPhone/iPod. MEM Press to save a radio station to the bar speaker’s memory.

FM Radio 1. Press the POWER button to turn the bar speaker on. 2. Press the SOURCE button (iPod button on the remote) to switch to iPhone/iPod mode. 3. Press the iPod DRAWER button to open the MOTORIZED DOCK FOR iPhone/iPod 4. Locate the numbered bracket that fits the iPhone/iPod model that will be docked. Each included bracket has a number on it, indicating which iPhone/iPod model that bracket is compatible with. See the separate bracket chart page to identify which bracket is needed. 5. Snap the bracket into place over the iPhone/ iPod connector in the motorized dock. 6. Connect the iPhone or iPod to the connector inside the Dock for iPhone/iPod. When the speaker is plugged in, using AC power, the docked iPhone or iPod will charge. After docking an iPod or iPhone, the bar speaker will automatically switch to composite video output mode. 1. Follow the instructions for Docking an iPod or iPhone. 2. Press the PLAY/PAUSE button to begin playing music from the docked iPhone or iPod. Adjust the built-in FM Wire Antenna to improve FM radio reception. 1. Press the POWER button to turn the bar speaker on. 2. Press the SOURCE button to switch to Tuner mode. 3. Press the TUN/SKIP buttons on the remote to tune the FM radio. 1. Follow the instructions for Saving a Radio Station. 2. Press the MEMORY buttons on the remote to cycle through saved radio stations. 1. Follow the instructions for Tuning the FM Radio. 2. After tuning to the desired station, press the MEM button. 3. Press the MENU UP or MENU DN buttons on the remote to select a preset. 4. Press the MEM button to save the current radio station to the selected preset. Up to 20 stations can be saved to the bar speaker’s memory. Docking an iPod or iPhone Playing a Docked iPod or iPhone FM Antenna Tuning the FM Radio Listening to a Saved Radio Station Saving a Radio Station

iLive 9 Clock, Alarm, and Sleep Timer 1. Press the POWER button to turn the power off. 2. Press the CLOCK button on the remote control. 3. The time on the display will begin blinking. 4. Press the REV/MIN and FWD/HR buttons on the remote to adjust the minute and hour. 5. Wait 5 seconds to finish setting the clock. 1. Press the POWER button to turn the power on. 2. Press the SOURCE button on the bar speaker to switch to the desired sleep timer source. 3. Press the SLEEP button repeatedly to set the sleep timer. 4. After the set sleep time has expired, the bar speaker will automatically power off. 1. Press the POWER button to turn the power on. 2. Adjust the volume to the desired level. 3. Press the POWER button to turn the power off. 4. Press the ALARM button on the remote control. 5. The alarm time on the display will begin blinking. 6. Press the REV/MIN and FWD/HR buttons on the remote to adjust the minute and hour. 7. Press the SOURCE button on the bar speaker to switch to the desired alarm source. 8. Wait 5 seconds to finish setting the alarm. 9. ALARM will appear on the display when the alarm is set. 10. Press the ALARM button to cancel the alarm. Setting the Clock Setting the Sleep Timer Setting the Alarm Audio Inputs and Subwoofer Output 1. Connect a 3.5mm Audio Input cable (not included) to the 3.5MM AUDIO INPUT on the bar speaker and an audio source. 2. Press the POWER button to turn the bar speaker on. 3. Press the SOURCE button to switch to LINE mode. 4. Use the native controls on the connected audio device to begin playing music through the connected bar speaker. 1. Use an RCA cable (included) to connect an external subwoofer to the SUBWOOFER OUTPUT. 2. When audio is played through any source, the bar speaker will automatically use the connected subwoofer. 1. Connect an RCA cable (included) to the AUXILIARY INPUTS on the bar speaker and an audio source. 2. Press the POWER button to turn the bar speaker on. 3. Press the SOURCE button to switch to AV mode. 4. Use the native controls on the connected audio device to begin playing music through the connected bar speaker. Using the 3.5mm Audio Input Using the Subwoofer Output Using the RCA Audio Input

VCR GAMING CONSOLE SUBWOOFER TELEVISION Basic Connectivity This is a basic flow chart of how you can connect your home entertainment devices to the bar speaker, and in turn how the bar speaker connects to them. For optimal performance, always connect video sources such as a DVD players, gaming consoles or set-top boxes directly to your television. Video Inputs and Video Output For optimal performance, always connect video sources such as a DVD players, gaming consoles or set-top boxes directly to your television. 1. Connect an RCA cable (included) to the COMPOSITE VIDEO INPUT and a video source. 2. Follow the instructions for Using a Composite Video Output or Using the Component Video Output 3. Press the POWER button to turn the bar speaker on. 4. Press the VIDEO button on the remote to switch between Composite and Component video output modes. 5. Use the native controls on the connected video device to control video that runs through the bar speaker. 1. Connect an RCA cable (included) to the COMPOSITE VIDEO OUTPUT and a television. 2. Adjust the connected television to the proper input setting. 3. Press the VIDEO button on the remote to switch between Composite and Component video output modes. 4. Video from a docked iPhone/iPod, or a connected DVD player can now be played through the bar speaker to the connected television. The Component Video Output will only output video from a docked iPod or iPhone. It cannot output video from the composite video input. 1. Connect a component video cable (not included) to the COMPONENT VIDEO OUTPUT and a television. 2. Adjust the connected television to the proper input setting. 3. Press the VIDEO button on the remote to switch between Composite and Component video output modes. 4. Video from a docked iPhone/iPod, or a connected DVD player can now be played through the bar speaker to the connected television. Using the Composite Video Input Using the Composite Video Output Using the Component Video Output

iLive 11 Mounting to a Wall We recommend having this bar speaker professionally mounted. The included spacers should be used at your discretion to extend the face of the bar speaker farther from the wall. These are typically used when mounting the bar speaker under a television, and the face of the bar speaker needs to be flush with the face of the television. 1. Use the Tape Measure to decide how high you’d like to hang the bar speaker on the wall. 2. The bar speaker must be hung within 6 feet of an AC power outlet for the attached AC power cable to reach. 3. Use the Stud Finder to locate 2 parallel wooden studs to screw the mounting brackets into. 4. Mark the wall at the center of the studs using the Pencil. 5. Line the Level up on both of your marks to make sure they are level. If they’re not, adjust the marks as needed to make them level. 6. After you’ve double checked your markings, drill through the top hole on both mounting brackets directly into the marks you’ve made on the wall. 7. If you are using the brackets only and no spacers, use the included short screws. If you are using any of the spacers or combination of the spacers, use the long screws. 8. Use the Level to level each of the hanging brackets, then drill the second screw into the bottom hole on both mounting brackets. 9. Slide the bar speaker onto the mounting brackets, and make sure there is a firm and stable connection before letting go of the bar speaker. 10. Finally, use the Level to confirm that the bar speaker is level. • Manual or Power Screwdriver • Stud Finder • Pencil • Tape Measure • Level • (2) Wall Mount Brackets • (4) Long Screws • (4) Short Screws • (2) 1/4” Spacers • (2) 1/2” Spacers • (2) 3/4” Spacers • (4) Drywall anchors Important Notes Getting Started Required Tools Included Hardware 16” ITP231B ITP231B screws studs mounting bracket spacer

Specifications are subject to change without notice To download this User’s Guide in English, Spanish, or French, visit the support section at www.ilive.net. Para transferir esta guía de usuario en inglés, español, o francés, visite la sección de la ayuda en www.ilive.net. Pour télécharger ce guide de l’utilisateur en anglais, espagnol, ou français, visitez la section de soutien chez www.ilive.net. Phone: 1-888-999-4215 Email: [email protected] Parts Email: [email protected] Website: www.ilive.net International Support Contact Information Company Information