Advent xt Operation & User’s Manual

REPLACEMENT PAPER paper roll must be replaced with THERMAL PAPER only thermal sensitive coating must be on the outside paper rolls must be 58mm wide maximum paper roll diameter 55mm (37.7 metres long) replacement paper roll: Tynetec P/No. W00336 LOADING PAPER 1. slide the lid release button until the lid springs open 2. unwind a small amount of paper and insert into the printer 3. close the lid down and the paper is loaded After loading, check that the paper advances properly and tear off any excess by pulling towards you across the serrated edge. Cowley Road, Blyth Riverside Business Park, Blyth, Northumberland, NE24 5TF Tel: 01670 352371 Fax: 01670 362807 Email: [email protected] Website: www.tynetec.co.uk USER GUIDE FOR THE ADVENT xt COMPACT THERMAL PRINTER Model No: Tynetec ZXT311

warden call system. All other system activity such as telephone line fault, mains fail, system reset, etc. is also recorded. PUSHBUTTON The pushbutton performs several functions; click once to turn the printer on, press and hold for paper feed when changing paper rolls or double-click to perform a self test and print the internal settings. LED INDICATOR The LED indicator on the front of the printer will normally flash short green - long orange, there are a number of other colour combinations which provide printer status information; Battery Flat - or printer in sleep mode No LED Spool  Error Condition Fast Flashing Red Spool  Fast Charging Fast Flashing Orange Spool  Battery Low Short Green - Short Red Normal Battery Low Long Green - Short Red Spool  Running on Battery Fast Flashing Green Normal Running on Battery Steady Green Spool  Trickle Charging Long Orange Flashing Normal Trickle Charging Short Green - Long Orange Buffer Mode Battery Status LED Pattern  The printer will enter Spool Mode if the paper runs out, the paper compartment flap is up or an error has occurred. Data will be buffered for printing when the condition is rectified. BATTERY STANDBY If the mains supply is disconnected the LED will be steady green for a preprogrammed time until the printer enters sleep mode. When the mains supply is restored click the pushbutton to return to standby mode and any missed calls will be printed. PRINT-OUT DETAILS The print-out is designed to give as much information as possible about the status of the system whilst using the minimum of paper. All alarm call print-outs are restricted to one line of text in the following format: Operating Mode Time (24HR) Date (DDMM) Call Type Channel ID Alarm Prefix Example: AL 0001 INTERCM 22/12 14:20 ON The above example tells you an intercom alarm from flat 1 was detected at 14:20 on 22 December and the system was operating in onsite mode. See below for details of the abbreviations used; ALARM PREFIXES AL Alarm Call SA System Alarm CA Call Answered SR System Report CE Call Ended FN Function Start/Finish Time CB Call Back Start/Finish Time (eg. FN 1000 = All Call) CALL TYPES INTERCM Intercom Alarm CO GAS Carbon Monoxide Alarm PENDANT Pendant Alarm GAS Natural Gas Alarm PCORD Pullcord Alarm FLOOD Flood Detector Alarm SMOKE Smoke Alarm LO TEMP Hypothermia Alarm OPEN CT Open Circuit Fault BED OCC Bed Occupancy Alarm AL FAULT Intercom Fault (not responding) CL WAND Client Wandering Alarm INACTIV Inactivity Alarm PILL DS Pill Dispenser Alarm INTRUDR Intruder Alarm ENURES Enuresis Alarm PARKED Intercom Parked SYSTEM ALARMS (SA) 4797 BT FLT Telephone Line Fault 3999 FIRE AL Fire Alarm Activated 4796 BT OK Telephone Line Restored 4800 NTR FLT Network Receiver Fault (ID 800-815) 4799 MAIN FL Mains Failed 4816 NEI FLT Network PBX I/F Fault (ID 816-823) 4798 MAIN OK Mains Restored 4824 NKS FLT Network Keyswitch Fault (ID 824-827) 4793 LOW BT Low Battery 4794 FUSE BL Low Voltage Fuse Blown SYSTEM REPORTS (SR) CARE CL Extracare Call Cancelled DIAL TELE 01 Dial Telephone Number 01 SYSTEM RESET System Reset BT LINE DROP Telephone Line Dropped RING DETECT Telephone Line Ring Detected BT LINE SEIZ Telephone Line Seized SUB PRIVACY Intercoms with Privacy On OPERATING MODES ON Onsite Mode LO Local Offsite Mode RO Remote Offsite Mode DOOR ENTRY DE 0032 DOOR 01 Flat 32 Called From Door Panel 1 DE DOOR OPEN 01 Door Entry Opened Door 1 TEL TRANS EN 0001 TO 0002 Flat 1 Door Entry Telephone Calls Transferred to Flat 2 TEL TRANS EN 0001 Confirm Flat 1 Door Entry Telephone Calls are Transferred CALL TRANS EN 0008 24 Hour Calling Enabled for Flat 8 CALL TRANS DIS 0008 24 Hour Calling Disabled for Flat 8 TEL PRIVACY 0015 Flat 15 Door Entry Telephone has Privacy ON TEL FAULT 0020 Flat 20 Door Entry Telephone has a Fault Note: to conserve paper all door entry related print-outs can be disabled via the Advent xt “Door Entry Setup” webpage.