Birch BD-408e Manuals

a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interface when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interface to radio communications. Operation of this equipment in a residential area is likely to cause harmful interface in which case the user will be required to correct the interface at his own expense.  All brand and trademark are belonged to their respective owner.  Specifications are subject change without notice. This device complies with part 15 of the FCC Rules. Operation is subject to the following two condition: (1) This device may not cause harmful interface, and (2) This device must accept any interface received, including Interface that may cause undesired operation. 1

Installation«««««««««««««««««««««««««««««««««««4 Recommended Steps«««««««««««««««««««« 4 Configuration Flowchart««««««««««««««««« 5 String Output Flowchart««««««««««««««««««5 Default Setting««««««««««««««««««««««««««««« 6 Manual Label Layout««««««««««««««««««««« 7 Frequent Question«««««««««««««««««««««««« 8 2 Interface««««««««««««««««««««««««««««««««««««««««««««««««««««««« 10 Host Interface«««««««««««««««««««««««««««««« 10 Keyboard Wedge«««««««««««««««««««««««««« 11 RS-232C«««««««««««««««««««««««««««««««««««««15 Wand Emulation (Linker or Pen)«««««««18 OCIA««««««««««««««««««««««««««««««««««««««««« 20 3 System Control««««««««««««««««««««««««««««««««««««««««««««« 21 4 Code Option««««««««««««««««««««««««««««««««««««««««««««««««« 26 UPC-A««««««««««««««««««««««««««««««««««««««««26 UPC-E««««««««««««««««««««««««««««««««««««««««28 EAN-13 (ISBN/ISSN) «««««««««««««««««««« 30 EAN-8«««««««««««««««««««««««««««««««««««««««« 32 CODE-39 (CODE-32) ««««««««««««««««««« 34 Interleaved 2 of 5 (Odd S-code) «««««« 36 Industrial 2 of 5«««««««««««««««««««««««««««««38 Matrix 2 of 5«««««««««««««««««««««««««««««««« 40 China Post 2 of 5«««««««««««««««««««««««««« 42 Codabar/NW7«««««««««««««««««««««««««««««« 44 Code-128««««««««««««««««««««««««««««««««««« 46 Code-93««««««««««««««««««««««««««««««««««««« 48 Code-11««««««««««««««««««««««««««««««««««««« 50 MSI/Plessey«««««««««««««««««««««««««««««««« 52 UK/Plessey««««««««««««««««««««««««««««««««« 54 Telepen«««««««««««««««««««««««««««««««««««««« 56 IATA«««««««««««««««««««««««««««««««««««««««««« 58 5 String Format««««««««««««««««««««««««««««««««««««««««««««««««60 Preamble/Postamble««««««««««««««««««««« 60 Prefix/Suffix««««««««««««««««««««««««««««««««« 61 Character Insertion««««««««««««««««««««««««62 Other Control««««««««««««««««««««««««««««««« 64 6 Cable Type««««««««««««««««««««««««««««««««««««««««««««««««««««66 7 Test Chart««««««««««««««««««««««««««««««««««««««««««««««««««««« 68 8 ASCII Code/Hexdecimal Table«««««««««««««««««««««««71 3

form your equipment before connecting the scanner. Beside, you also have to check the cable connector of the scanner match your equipment interface correctly. 2) Boot up your computer after connecting the scanner with your equipment, the scanner will make a long music and light the LED, above scanner to indicate a successful power on. Trigger the button, the scan line in front of scanner will active. Now you can start to set programming optimal usage.  If any of the above operation is not right, turn off the power immediately and check any improper connections. Go through all above steps again. Recommened Steps When the required settings have been configured, all settings are stored in non volatile memory of scanner after reading EXIT label. There are recommended steps as follows. 1) Set right host interface for your scanner at /10. (The scanner is in factory default as bold label) 2) Set interface to optimize protocol of scanner with your host in Charter 2. 3) Set system control of scanner, such as specific adjustments double confirm, power saving, indicator and scanning mode which you prefer usage in Chapter 3. 4) Set code option of scanner for your usage in Chapter 4. You must make sure to enable the symbology first, then Min./Max. code length, code ID checksum and truncate digits are also convered. 5) Set string format of the scanner, such as preamble, postamble, prefix, suffix, code ID and code name transmission for your application in Chapter 5.  If any of the error step is processing, scanner will generate a 5 wanrrying beeps to indicate an invaild setting. You have to take care this matter and set correctly again.  If still not work properly. Please contact with dealer. Operation Manual 4

Preamble Prefix Code Name Code ID Code Data Code Length Suffix Postamble Enter Programming Mode Finish ASCII Code or Decimal Value Setting Select Function Label Interface Default Exit & Interface Default Function PROGRAM Decimal (10's Value) Hexdecimal (High Byte) Decimal (1's Value) Hexdecimal (Low Byte) SET EXIT ABORT VERSION DATE SETTING LIST DEFAULT Prefix or Suffix Only Set ASCII Code Set Decimal Value Exit With Save Exit Without Save Exit & Default Exit & Version List Exit & Setting List 5 Introduction 1