GE PB909SP3SS Installation Instructions

can tip. • BURNS or other SERIOUS INJURIES can result. • INSTALL and CHECK the ANTI-TIP bracket following the instructions supplied with the bracket. STEP 1 LOCATE THE BRACKET IMPORTANT: Determine the final location of the range before attempting to install the bracket. a. Place the bracket on the floor with the back edge against the rear wall. If the range does not reach the rear wall, align the back edge of the bracket with the rear panel of the range in its final location. RearWall Adjacentcabinet or final locationof range side panel LocA LocC LecB Two screws must enter floor orwall at LecA, BerC. ir bracket does not touch the rear wall, gou MUST screw bracket to FLOOR as described in Step 2. b. Position the side of the bracket against either the left or right cabinet. If there is no adjacent cabinet, align the edge of the bracket with the side panel of the range in its final location. If the countertop overhangs the cabinet, offset the bracket from the cabinet bg the amount of overhang. c. Mark the location for the pair of holes to be used (see illustration above). NOTE: For FLOOR installation use either Loc A or B. For REARWALL installation use Loc C. 31-10671 ] 04-08 JR To reduce the RISKOFTIPPINGthe range, the range must be secured bg a properly installed ANTI-TIP BRACKET. Secure the bracket with the screws provided. NOTE: The installation of the ANTI-TIP bracket must meet all local codes for securing the appliance. If gou did not receive an anti-tip bracket with gour purchase, call 1-800-626-8774 to receive one at no cost. In Canada, call 1-800-561-3344, For installation instructions of the bracket, visit: GEAppliances.com. In Canada, GEAppliances.ca. STEP 2 SECURE THE BRACKET The bracket must be screwed to either the FLOOR or REAR WALL. Attachmentto Flooror RearWall Bracket Wall Sill Plate /Screw mustenter "_ __] wood orconcrete Screw mustenterwood FLOOR Installation: WOOD FLOOR: Use the screws provided to secure the bracket using the pair of marked holes (either Loc A or B). CONCRETEFLOOR: Using a concrete bit, drill a 5/32" pilot hole 2" deep into the concrete at the center of each of the marked holes (either Loc A or B). Use the screws provided to secure the bracket into the floor. REARWALL Installation: Use the 2 screws provided to secure the bracket using the pair of marked holes at Loc C.The screws MUST enter into a wood sill plate. If the wall contains ang metal studs or similar materials, then the floor must be used. STEP 3 CHECKTHE BRACKET After installing the bracket, slide the range into its final location. The rear leveling leg must be fullg inserted into the ANTI-TIP bracket. If the range has a storage drawer, remove the drawer and look underneath the range to see if the leg is fullg engaged in the bracket as shown in Step !. On models without storage drawer or kickpanel, verifg the rear leveling leg is properlg secured within the bracket bg carefullg tipping the range forward. DO NOTtip the range more than 4 inches. If the bracket does not stop the range within 4 inches, the bracket is NOT properlg installed and MUST be reinstalled following these instructions. A he anti-tip bracket must be PROPERLYINSTALLED and the rear leveling leg must be FULLY ENGAGEDinto the bracket to prevent the range from tipping. NEVER remove the leveling legs. This will prevent the range from being secured to the ANTI-TIP bracket properlg.

1-800-626-8774pararecibirunosincostaalguno. EnCanad6,Ilameal 1-800-561-3344. Parainstruccionesde instalaci6ndelsoporte,visite:GEAppliances.com. EnCanad6,GEAppliances.ca. PASO 1 UBIOUE ELSOPORTE IIvlPORTANTE:Determine la ubicaci6n final de la cocina antes de tratar de instalar elsoporte. a. Coloque el soporte en el piso con el lado trasero sabre la pared trasera. Sila cocina no Ilega a la pared trasera, alinee el lado trasero del soporte con el panel trasero de la cocina en su ubicaci6n final. Gabineteadyacenteo ubicaci0nfinal del panel lateral dela cocina \ Paredtrasera Ubic. C Ubic.A Ubic.B Dostornillos debeningresar enel piso o pared en la Ubic.A, Bo C. Siel soporte no toca la pared trasera, usted DEBE atornillar el soporte al PlSOcoma se describe en el Paso2. b. Coloque el lado del soporte sabre el gabinete izquierdo o derecho. Si no hay un gabinete adyacente, alinee el extremo del soporte con el panel lateral de la cocina en su ubicaci6n final. Si el mostrador de encimera sobresale del gabinete, modifique la posici6n del soporte desde el gabinete considerando la cantidad que sobresale. c. Marque la ubicaci6n para el par de orificios que se utilizar6n (vet la ilustraci6n de arriba). NOTA: Para instalaciones de PISO utilice la Ubic. A o B. Para la instalaci6n de PAREDTRASERAutilice la Ubic. C. 31-10671 ] PASO 2 SUJETE ELSOPORTE Elsoporte debe atornillarse al PISOo a la PAREDTRASERA. SujeciOnal piso o la paredtrasera Saparte Eltornilledebe ingresarenmadera __J o concrete Umbraldela pared Instalaci6n de PISO: Eltornillo debeingresarenmadera PISODEMADERA:Utilice los tomillos provistospara sujetar el soporte utilizando el par de orificios marcados (Ubic.A o B). PISODECONCRETO:Utilizando una broca para concreto, perfore un orificio piloto de 5/32" de 2" de profundidad dentro del concreto en el centro de cada uno de los orificios marcados (Ubic. A o B). Utilice los tornillos provistos para sujetar el soporte al piso. Instalaci6n de PAREDTRASERA: Utilice los 2 tomillos provistos para sujetar el soporte utilizando el par de orificios marcados en Ubic. C.Lostomillos DEBENingresar en el umbral de madera. Si la pared contiene parantes de metal o materiales similares, entonces debe usarse el piso. PASO 3 VERIFIOUE ELSOPORTE Despu@sdeinstalar el soporte,deslicela cocina a su ubicaci6n final. Lapata de nivelaci6n trasera debe introducirse par completo en el soporte ANTI-VOLCADURAS.Sila cocina cuenta con el caj6n de almacenamiento, quite el caj6n U mire debajo de la cocina para vet si la pata estd bien enganchada en el soporte coma puedeverse en el Paso!. En modelos sin guanteras ni paneles delanteros inferiores, verifique que lapata de nivelaci6ntrasera seencuentre bien asegurada dentro del soporte inclinandocon cuidadola cocina hacia delante. NOinclinela cocina mds de4 pulgadas.Sielsoporte no detiene la cocina dentro de las4 pulgadas,elsoporte NOest6bien instalado U DEBEvolver a instalarse siguiendoestasinstrucciones. A I soporte anti-volcaduras debe INSTALARSEDEMANERA CORRECTAUla pata denivelaci6n trasera debe ENGANCHARSE BIENal soporte para evitar que la cocina vuelque. NUNCAquite las patas de nivelaci6n. Estono permitird que la cocina quede bien sujeta al soporte ANTI-VOLCADURAS. 04-08 JR