Interfire G1-1200 Instruction Manual

free installation. CONGRATULATIONS ON YOUR PURCHASE Your new high fidelity mono block amplifier is designed to deliver maximum enjoyment and one year of trouble free service. Please take a few moments to read this manual thoroughly. It will explain the features and operation of your unit and help insure trouble FEATURES • • • • • • • • • • • Class ''D'' Technology 1 Ohm Stable Spec Audiophile Grade Components High Efficiency PWM Power Supply - Multi-stranded power toroid - Tow toroidal core - MOSFET transistors Oversized Capacitor Banks Discrete Mount Power and speaker terminals Variable Low Pass Electronic Crossover 50Hz - 250Hz Built in power bridging module Circuit / Thermal / Overload Protection Bridge Sync Capable Remote Level Control IMPORTANT The quality of installation may affect the performance and reliability of your product. If you have any doubts or questions regarding installation, you may wish to contact your authorized dealer. Remember to heed all wire and fuse requirements suggested in this manual. Warranty may be void if proper installation technique is not used (refer to warranty 1 section in the rear of the manual )

2. Once the location has been determined, place the amplifier into position. Using a felt tip pen or pencil mark the four holes to be drilled for mounting. NEVER use the amplifier as a template for drilling. It is very easy to damage the amplifier surface in this manner. 3. Remove amplifier. Drill four 3.5 m/m holes into mounting surface. If you want to mount 4. If possible, test the system to ensure it is operating correctly before final mounting of 5. FIG.1 2 MOUNTING: Mount the amplifier using the supplied 4 self tapping screws. the amplifier to MDF or wood panel, drill four 3.0m/m diameter holes into mounting surface. the amplifier. INSTALLATION DIAGRAM Self Tapping Screws

POWER REM GND B+ FUSE 30A 30A 30A SPEAKER G1-2000 digital mono block AMPLIFIER POWER REM GND B+ The Class "D" amplifier is a SINGLE CHANNEL dedicated subwoofer amplifier. Unlike other amplifiers, the Class "D" operates as a single channel and cannot be bridged. Don't be fooled by the outputs. Two outputs are used strictly for convenience and are paralleled internally on the amplifier. This means that if both outputs are used with one driver each, the amplifier sees the same load as if the same drivers are connected to 4OHM SUBWOOFER 4OHM SUBWOOFER 4OHM SUBWOOFER 3 4OHM SUBWOOFER only one output terminal. See diagram below. SPEAKER WIRING In both diagrams, the amplifier sees a 2 ohm load.

BASS BOOST SLAVE MASTER MASTER /SLAVE REMOTE GAIN CONTROL 4 FROM RADIO MONO BRIDGED WIRING SUBWOOFERS (DUAL AMPS) When using dual amplifiers to power one subwoofer, the Positive terminal of the Subwoofers voice coil is connected the positive terminal of the MASTER Amplifier and the Negative terminal of the Subwoofers voice coil is connected to Positive terminal on the SLAVE Amplifier. This procedure will allow the total power of both amplifiers to be added together and act like a single powerful amplifier. Please check that your subwoofer power handling capabilities are not exceeded CAUTION Always check your speaker load with a multi-meter before hooking up to the amplifier. These digital amplifiers are only 1 ohm stable. Any Impedance (load) smaller than 1 ohm will damage the amplifier. Such Damage is not covered under warranty either, so pay strict attention to what when hooking two amplifiers to it. connections are made to the amplifier. Master Amplifier Slave Amplifier MASTER SLAVE MASTER SLAVE SPEAKER WIRING 0dB 12dB

POWER REM GND B+ FUSE 30A 30A 30A SPEAKER Gd-1000 digital mono block AMPLIFIER POWER REM GND B+ FUSE 30A 30A 30A SPEAKER Gd-1000 digital mono block AMPLIFIER POWER REM GND B+ FUSE 30A 30A 30A SPEAKER G1-2000 digital mono block AMPLIFIER POWER REM GND B+ 5 Master Amplifier Slave Amplifier (OPTION) TWO AMPLIFIER/ ONE SUBWOOFER (SINGLE VOICE COIL)CONFIGURATION CHASSIS GROUND REMOTE TURN ON BATTERY VIA FUSE Using a lead wire of 8 gauge or bigger connect from the master Amp's negative(-) speaker terminal to the slave Amp's negative(-) speaker terminal. Master Amplifier Slave Amplifier Recommend : Competition Only MONO BRIDGED SPEAKER WIRING

POWER REM GND B+ FUSE 30A 30A 30A SPEAKER G1-2000 digital mono block AMPLIFIER POWER REM GND B+ FUSE 30A 30A 30A SPEAKER G1-2000 digital mono block AMPLIFIER POWER REM GND B+ FUSE 30A 30A 30A SPEAKER G1-2000 digital mono block AMPLIFIER POWER REM GND B+ MONO BRIDGED (OPTION) FOUR AMPLIFIER/ ONE SUBWOOFER (DUAL VOICE COIL)CONFIGURATION 6 Master Amplifier Slave Amplifier Master Amplifier Slave Amplifier Voice Coil1 Voice Coil2 SPEAKER WIRING

Class "D" amplifier is capable of drawing in excess of 90 amperes,4 gauge wire is recommended for lengths up to twenty feet. if a longer length is needed , a larger gauge Amplifier power wire should be wired directly to the battery using the wire requirements listed above. Start at the amplifier and run the power wire through the vehicle to the battery. The use of grommets is recommended when passing the power wire through any metal wall. Avoid sharp corners or sharp body parts that may easily cut through the insulation on the wire. Avoid running the power wire over engine components and near heater cores. Use an inline fuse to eliminate the risk of a fire caused by a short in your power wire. Connect the fuse holder as close to the battery positive as possible. For most applications, an 80 ampere Maxi fuse or comparable ANL wafer fuse can be used. Now connect the wire to the battery, but remember to leave the fuse out until all other POWER SUPPLY CONNECTIONS RECOMMENDED POWER WIRE POWER The Class "D" amplifier is designed to work within 10 to 16 volts DC. Before any wires are connected, the vehicle's electrical system should be checked for correct voltage supply with the help of a voltmeter. First check the voltage at the battery terminals with the ignition in the off position. The voltmeter should read no less than 12 volts. Next, check the battery with the engine running between 1500 and 2000 rpm. The voltmeter should now read between 13.5 and 14.5 volts. If your vehicle's electrical system Is not up to these specifications, we recommend having it checked by an automotive mechanic before further installation. wire may be necessary. wire connections are mode. When grounding your amplifier, locate a metal area close to the amplifier that is a good source of ground ( preferably the floor ).Once again, investigate the area you wish to use for electrical wires, vacuum lines, and brake or fuel lines. Using either a wire brush or sandpaper eliminate unwanted paint to supply a better contact for your ground. Use the same gauge wire for ground as you did for the power. Terminate the ground wire using the correct size ring terminal and attach it to the bare metal using a nut and bolt. It is important for this connection to be solid. To complete the job, spread silicon over the screw and bare GROUND REMOTE TURN-ON metal to prevent rust and possible water leaks. In between the power and ground is a remote turn-on terminal. This terminal must be connected to a switched +12volt source. Typically, remote turn-on leads are provided at the source unit that will turn on and off the amplifier in correspondence with the source. If a radio does not have a remote turn-on, then a power antenna wire may be used. Yet, if neither of these leads are available at the source, a switched +12 volt supply must be supplied. Run a minimum of 18-gauge wire from the amplifier location to the source of the switched +12 volt lead. If possible, route this wire on the same side of the vehicle as your power wire. Connect the source remote output wire to the REM terminal on the amplifier using a 3mm screw key. Cut the remote wire to length. Strip approximately 1/2 inch of insulation from the end of the wire and insert into the terminal. Tighten the screw securely.

BASS BOOST SLAVE MASTER MASTER /SLAVE REMOTE GAIN CONTROL 8 1 2 3 4 5 6 7 1. RCA Input Jacks 2. Input Level Control 3. Low Pass Frequency 4. Bass Boost 5. Remote Control Jack 6. Master/Slave Switch 7. Slave Input Jack OPERATION Control and Crossover 1. RCA Input Jacks - Low level-high impedance inputs. Use high quality RCA cables designed for mobile applications. 2. Input Level Control - Adjust the input level for the marked channels. Turn clockwise to increase the level, counterclockwise to decrease. Amplifiers will run cooler and produce less system noise at lower level settings. 3. Low Pass Frequency - Adjust the crossover frequency by turning clockwise to set to a higher frequency, counterclockwise to set to a lower frequency. 4. Bass Boost - Adjust the sub boost level of the selected frequency output from 0dB to 12dB. 5. Remote Control Jack - For connecting the remote control module to the amplifier. 6. Master/Slave Switch - Select the remote level control or the on-board level control as the master control. 7. Slave Input Jack - Used to connect to another amplifier when bridging 2 amps together. The Slave mode bypasses normal input jacks and controls.

POWER REM GND B+ FUSE 30A 30A 30A SPEAKER Gd-2000 digital mono block AMPLIFIER POWER REM GND B+ SPEAKER POWER REM GND B+ Gd-3000 digital mono block AMPLIFIER LINE INPUT CH1 CH2 GAIN LPF 6V 0.2V 50Hz 250Hz 0dB 12dB BASS BOOST SLAVE MASTER MASTER /SLAVE REMOTE GAIN CONTROL

and solutions. Before you consult this listing, make sure the vehicle's electrical system is working properly by verifying that other electrical items (e. g. headlights, windows, etc.) Still function correctly. TROUBLE SHOOTING GUIDE No Audio Low or N.C Remote Turn-on connections Blown Fuse Power wires not connected Blown or non speakers connected Check remote turn-on voltage at amp and head unit Replace with new fast-blow fuse Check butt splices or solder joints Check ground and battery connections Use VOM or DVM to measure speaker coil impedance; check speaker wiring connections SOLUTION PROBABLE CAUSE SYMPTOM See adjustment procedure and check each step; Inspect each speaker for damage and repair or replace suspected component Refer to head unit owner's manual Input Sensitivity not set properly or damaged speaker cones Low turn-on voltage Distorted Audio Audio Level Low Mute circuit on head unit is on. Check electrical system for low voltage; Check ground connection Audio Lacks Speakers wired with wrong polarity, causing cancellation of bass frequencies Check polarity of wires from amplifiers to each speaker as defined by the system design Check battery voltage at amplifier during operation External Fuse Blowing Incorrect wiring or short circuit Refer to electrical installation and check each installation step Whining noise on audio with engine running Amplifier is picking up alternator noise Install an in-line noise filter on the head unit's power wire; Check alternator routing diodes or voltage regulator for proper operation. Check all grounds , battery voltage, and RCA cables Ticking noise on audio with engine running Amplifier is picking up radiated spark noise Check RCA audio cable; Install an in-line noise filter on the head unit's power wire. Check spark plug wires.

for improvements. SPECIFICATION AMPLIFIER G1-1200 G1-2000 G1-3000 RMS POWER / 1 ohm @ 1% T.H.D 1200W x 1 2000W x 1 3000W x 1 750W x 1 1000W x 1 2000W x 1 400W x 1 500W x 1 1000W x 1 90% 90% 90% 79% 79% 79% 10Hz ~ 250Hz 10Hz ~ 250Hz 10Hz ~ 250Hz >100dB >100dB >100dB 150 150 150 200mV ~ 6V 200mV ~ 6V 200mV ~ 6V 20K Ohms 20K Ohms 20K Ohms 75Amp 90 Amp Need External Fuse/ Minimum 180 Amp 245 x 55 x 320 245 x 55 x 350 245 x 55 x 420 50 ~ 250Hz 50 ~ 250Hz 50 ~ 250Hz 24dB 24dB 24dB 0dB ~ 12dB 0dB ~ 12dB 0dB ~ 12dB 2 ohms @ 0.05% T.H.D 4 ohms @ 0.05% T.H.D Efficiency / Typical @ 4 ohms MIN RATE @ 1 ohm Signal To Noise Ratio ('A' WTD) Damping Factor Input Sensitivity Input Impedance Circuit Breaker Dimensions (W x H x D) mm Variable Low Pass Filter X-Over Slope Variable Bass Boost Bandwidth ±1dB

WARRANTY WARRANTY LIMITATIONS The following is NOT covered under Interfire Audio's warranty program: NOTICE: Products shipped without a valid RA # will be refused and shipped back. manual lightning, etc.) Custom finishes) Product with defaced, altered or removed serial numbers (no valid, legible serial No. = no warranty). or missing magnets. 1. 3. 4. 5. 6. 7. 8. WARRANTY TERMS (Effective January 01, 2010) These terms supersede all prior published warranty terms Interfire Audio products are warrantied against defects in materials and workmanship for a period of One (1) Year from the original date of purchase. Products found to be defective during the warranty period will be repaired or replaced (with a product deemed to be equivalent) at Interfire's discretion. Note: Products purchased from unauthorized dealers are not covered under warranty. Ask your dealer for details on warranty limitations. INTERNATIONAL WARRANTIES: Products purchased outside the United States of America are covered only by that country's distributor and not by Interfire Audio, Inc. IF YOU NEED SERVICE ON YOUR INTERFIRE AUDIO PRODUCT: and box. 9. Product damaged cosmetically due to improper handling or normal wear and tear Including Freight damage. Be sure to package all returns in its packing material 10. Installation and shipping costs associated with removing, re-installing or shipping the product to Interfire Audio for warranty service Interfire Audio dealer. (The warranty is Product owned by anyone other than the original purchaser from an authorized NOT transferable and will not apply to products purchased from unauthorized dealers.) or spiders). 2. Speaker products that have been over- powered, causing thermal (burnt voice coil) and/or mechanical failure (ripped surrounds Product that has NOT been installed according to the instructions in the owner's Product in which repair and/or modification has been attempted by unauthorized parties Product damaged in an accident, due to criminal activity (attempted theft, gunshot damage, etc.) or by "acts of God" (flooding, Product that has been physically damaged abused and/or altered. Including bent frames Custom finishes or other cosmetic treatments responsible for restoring or maintaining any sales receipt.) Direct returns from consumers by proof of purchase (a copy of the original 1-877-90-AUDIO to obtain an RA # (Return Authorization number). All warranty returns should be sent to INTERFIRE AUDIO freight prepaid through an authorized INTERFIRE AUDIO dealer and must be accompanied or non-authorized dealers will be refused unless specifically authorized by INTERFIRE AUDIO with a valid return authorization Please call Interfire Customer Service at number. Warranty expiration on products returned without proof of purchase will be determined from the manufacturing date code. Coverage may be invalidated as this date is previous to purchase date. Return only defective components. Non-defective items received will be returned freight-collect. Customer is responsible for shipping charges and insurance in sending the product to INTERFIRE AUDIO. Freight damage on returns is not covered under warranty. Always include proof of purchase (sales receipt).