CEL ZICM2410-EVB3 Reference Manual

Hardware Reference Guide 0007-05-08-03-001 (Rev C)

Rev C Document No. 0007-05-08-03-001 Page 2 of 19 Table of Contents 1 INTRODUCTION .............................................................................. 3 1.1 PART DEFINITIONS .................................................................................... 3 2 ZICM2410-EVB3 EVALUATION BOARD ......................................... 4 2.1 BOARD COMPONENTS ............................................................................. 4 3 MESHCONNECT ZICM2410P0 MODULE ....................................... 6 3.1 DESCRIPTION ............................................................................................ 6 3.2 ZICM2410P0 MODULE CONNECTION ....................................................... 7 3.3 ZICM2410P2 MODULE CONNECTION ..................................................... 10 4 ON BOARD RESOURCES ............................................................. 13 4.1 POWER SUPPLY ....................................................................................... 13 4.2 RESET ....................................................................................................... 13 4.3 ISP SWITCH .............................................................................................. 13 4.4 POWER HEADER (J4) .............................................................................. 14 4.5 LEDS .......................................................................................................... 14 4.6 PUSHBUTTON SWITCHES ...................................................................... 15 4.7 EXTERNAL MEMORY ............................................................................... 15 4.8 VOICE CODEC .......................................................................................... 15 4.9 HEADPHONE / MICROPHONE JACKS .................................................... 15 4.10 ADDITIONAL JUMPER FUNCTIONS/CONNECTIONS ............................ 16 5 REVISION HISTORY ...................................................................... 17 APPENDIX-1: SCHEMATIC OF ZICM2410-EVB3 ............................... 18 APPENDIX-2: BILL OF MATERIALS (ZICM2410-EVB3) .................... 19

Rev C Document No. 0007-05-08-03-001 Page 3 of 19 1 INTRODUCTION This document describes the hardware, features and functions of the CEL ZICM2410-EVB3 Evaluation Board, one of the major hardware components in the CEL ZICM2410P0-KIT2 evaluation kit. At the heart of the evaluation board is the ZICM2410P0 (or ZICM2410P2), CEL’s transceiver module solution for IEEE 802.15.4 wireless applications. 1.1 PART DEFINITIONS  ZIC2410QN48: CEL MeshConnect single-chip IEEE 802.15.4 transceiver.  ZICM2410P0: CEL MeshConnect IEEE 802.15.4 module.  ZICM2410P2: CEL MeshConnect Extended Range IEEE 802.15.4 module with an external power amplifier.  ZICM2410-EVB3: An evaluation board containing a ZICM2410P0-1 for development and evaluation purposes. Using the CEL supplied software tools makes it possible to download user-created programs to the ZIC2410.  ZICM2410P0-KIT2: CEL MeshConnect IEEE 802.15.4 evaluation kit.  ZIC2410: Same as the ‘ZIC2410QN48’.

Rev C Document No. 0007-05-08-03-001 Page 4 of 19 2 ZICM2410-EVB3 EVALUATION BOARD CAUTION: Contains parts and assemblies susceptible to damage by Electrostatic Discharge (ESD) The ZICM2410-EVB3 is a PC interface board to which the ZICM2410P0 / ZICM2410P2 module has been mounted. A ZICM2410-EVB3 can be used to interface PC applications with the module, in order to program user applications to the ZICM2410. 2.1 BOARD COMPONENTS Figure 1 shows the ZICM2410-EVB3 evaluation board, the major components of which are described in Table 1. Figure 1 – Photo, ZICM2410-EVB3 Evaluation Board

Rev C Document No. 0007-05-08-03-001 Page 5 of 19 Table 1 – ZICM2410-EVB3 Descriptions / Functions of the Major Components Components Description / Function Audio / Voice Jacks Microphone input and Headphone output for connection when using the evaluation board’s voice / audio features. ZICM2410 Module ZICM2410 module. The DUT of the evaluation board DIP Switches 3 ea 10-pin DIP Switches used for disconnecting the evaluation boards connections to the various on board features (i.e. LEDs, switches, etc.). ISP Switch ISP Mode Switch: 2-position slide switch to control ISP mode ‘ISP’ position is used for downloading application firmware to the ZICM2410. For normal operation, the switch should be set to the ‘NORMAL’ position. RESET Switch Button switch to reset the device MPU (Active Low) General Purpose LEDs Four indicator LEDs for GPIO output tests Test Tact Switches Push Button Switches connected to General Purpose I/O (GPIO) Ports: When a button is pressed, the signal ‘0’ is applied to the corresponding port pin; otherwise, a value of ‘1’ is applied. Switches #3 and #4 can be configured as external interrupts to the 8051 microcontroller. Battery Holders Holder for 2 ea. 1.5 Volt Type AA Batteries DC JACK Input for a 5.0 – 9.0 Volt DC Power Supply POWER Switch This three position slide switch is used to select the power source for the evaluation board. In the position ‘VREG’, power is supplied either through the USB port or from a power supply inserted in the DC Jack. In the ‘VBAT’ position, batteries provide the power. Power Indicator LED LED indicates when DC power is turned on. USB Port Port to connect the evaluation board through a USB cable to a PC. ADC Variable Resistors Variable Resistors for testing ADC functions in the ZICM2410 module Current Monitor For measuring operating current of the module under various conditions USB to UART Bridge Silicon Labs CP2102 USB to UART Bridge IC: Converts I/O from USB to UART. Analog Inputs 1 ea. 4-pin header to provide a convenient method to monitor or connect to an Analog input. Digital I/O Headers 3 ea. 8-pin header to provide a convenient method for to monitor or connect to a selected Digital GPIO port. SPI Flash Memory Onboard ROM for storing additional information. Voice CODEC Onboard Voice CODEC used for A/D and D/A conversions of Voice / Audio. Power Header 4-pin header for direct powering of the EVB, bypassing the internal regulator

Rev C Document No. 0007-05-08-03-001 Page 6 of 19 3 MeshConnect ZICM2410P0 MODULE CAUTION: Contains parts and assemblies susceptible to damage by Electrostatic Discharge (ESD) 3.1 DESCRIPTION The ZICM2410P0 / ZICM2410P2 module is the primary active component/device under test of the ZICM2410-EVB3 evaluation board. Figure 2 shows the ZICM2410P0 / ZICM2410P2 modules, whose major components are as follows:  ZIC2410QN48  Power Amplifier and Low Noise Amplifier (only found on the ZICM2410P2)  16MHz Crystal  Integrated PCB Trace antenna (or optional U.FL connector for an external antenna)  Additional components for RF matching and termination Figure 2 – Photo, ZICM2410P0 / ZICM2410P2 Modules

Rev C Document No. 0007-05-08-03-001 Page 7 of 19 3.2 ZICM2410P0 MODULE CONNECTION Table 2, Table 3 and Table 4 describe the ZICM2410P0 module pins and their connection to the DIP switches, which can be used for isolation (to disconnect the evaluation board from the ZICM2410P0). Also listed is the ZIC2410 (discrete IC) pin number. The tables also indicate the default settings of the isolation DIP switches (U203, U204 and U205) for operation with the pre- programmed application. All module GND pins are physically hardwired to ground. Table 2 – ZICM2410 / EVB3 Connections, U204 PIN # U204 POSITION MODULE PIN NAME DESCRIPTION IC MODULE U204 PAD 1 GND4 Connected to Ground. PAD 2 GND3 Connected to Ground. 14 3 MS1 Connected to Ground. PAD 4 GND0 Connected to Ground. 13 5 MS0 Connected to Ground. 6 NC2 No Connection. PAD 7 GND20 Connected to Ground. PAD 8 GND12 Connected to Ground. PAD 9 GND13 Connected to Ground. PAD 10 GND17 Connected to Ground. PAD 11 GND5 Connected to Ground. 8 12 1 ON ACH0 ADC Input, Channel #0. When U204:1 “ON” - Connected to VR1 on EVB3 9 13 2 ON ACH1 ADC Input, Channel #1. When U204:2 “ON” - Connected to VR2 on EVB3 10 14 3 ON ACH2 ADC Input, Channel #2. 11 15 4 ON ACH3 ADC Input, Channel #3. 20 16 5 ON P1_7 GPIO P1.7 21 17 6 ON P1_6 GPIO P1.6 22 18 7 ON P1_4 GPIO P1.4 When U204:7 “ON” - Connected to SW2 on EVB3 23 19 8 ON P1_3 GPIO P1.3 When U204:8 “ON” - Connected to SW1 on EVB3 PAD 20 GND9 Connected to Ground. PAD 21 GND8 Connected to Ground. PAD 22 GND7 Connected to Ground. 24 23 9 ON P1_1 GPIO P1.1 When U204:9 “ON” - Connected to USB_RX on EVB3 7 24 VCC_3V Power Supply Input, See Section 4.1. 26 25 10 ON P1_0 GPIO P1.0 When U204:10 “ON” - Connected to USB_TX on EVB3

Rev C Document No. 0007-05-08-03-001 Page 8 of 19 Table 3 - ZICM2410 / EVB3 Connections, U205 PIN # U205 POSITION MODULE PIN NAME DESCRIPTION IC MODULE U205 27 26 1 ON P3_7 GPIO P3.7 When U205:1 “ON” - Connected to SPI Bus on EVB3 28 27 2 ON P3_6 GPIO P3.6 When U205:2 “ON” - Connected to SPI Bus on EVB3 29 28 3 ON P3_5 GPIO P3.5 When U205:3 “ON” - Connected to SPI Bus on EVB3 30 29 4 ON P3_4 GPIO P3.4 When U205:4 “ON” - Connected to SPI Bus on EVB3 30 GND10 Connected to Ground. 31 31 5 ON P3_3 GPIO P3.3 When U205:5 “ON” - Connected to SW4 on EVB3 32 32 6 ON P3_2 GPIO P3.2 When U205:6 “ON” - Connected to SW3 on EVB3 33 GND11 Connected to Ground. 33 34 7 ON P3_1 GPIO P3.1 When U205:7 “ON” - Connected to SPI Bus on EVB3 35 35 8 ON P3_0 GPIO P3.0 When U205:8 “ON” - Connected to LED4 on EVB3 36 GND6 Connected to Ground. 36 37 9 ON P0_7 GPIO P0.7 When U205:9 “ON” - Connected to I2S Bus on EVB3 37 38 10 ON P_06 GPIO P0.6 When U205:10 “ON” - Connected to I2S Bus on EVB3

Rev C Document No. 0007-05-08-03-001 Page 9 of 19 Table 4 - ZICM2410 / EVB3 Connections, U203 PIN # U203 POSITION MODULE PIN NAME DESCRIPTION IC MODULE U203 38 39 10 ON P0_5 GPIO P0.5 When U203:10 “ON” - Connected to I2S Bus on EVB3 39 40 9 ON P0_4 GPIO P0.4 When U203:9 “ON” - Connected to I2S Bus on EVB3 40 41 8 ON P0_3 GPIO P0.3 When U203:8 “ON” - Connected to LED1 on EVB3 41 42 7 ON P0_2 GPIO P0.2 When U203:7 “ON” - Connected to LED2 on EVB3 42 43 6 ON P0_1 GPIO P0.1 When U203:6 “ON” - Connected to LED3 on EVB3 43 44 5 ON P0_0 GPIO P0.0 When U203:5 “ON” - Connected to I2S Bus on EVB3 19 45 4 ON DVDD_1_5 1.5 Volt Regulated Output, Digital Plane. 15 46 3 ON ISP ISP Mode Select When U203:3 “ON” - Connected to SW7 on EVB3 17 47 2 ON RESET# When U203:2 “ON” - Connected to SW5 on EVB3 6 48 1 ON AVDD_1_5 1.5 Volt Regulated Output, Analog Plane. 49 GND14 Connected to Ground. 50 GND15 Connected to Ground. 51 GND16 Connected to Ground. 52 GND18 Connected to Ground. 53 GND19 Connected to Ground. 54 NC1 No Connection. 55 GND1 Connected to Ground. 56 GND2 Connected to Ground.

Rev C Document No. 0007-05-08-03-001 Page 10 of 19 3.3 ZICM2410P2 MODULE CONNECTION Table 5, Table 6 and Table 7 describe the ZICM2410P2 module pins and their connection to the DIP switches, which can be used for isolation (to disconnect the evaluation board from the ZICM2410P2). Also listed is the ZIC2410 (discrete IC) pin number. The tables also indicate the default settings of the isolation DIP switches (U203, U204 and U205) for operation with the pre- programmed application. All module GND pins are physically hardwired to ground. Table 5 – ZICM2410 / EVB3 Connections, U204 PIN # U204 POSITION MODULE PIN NAME DESCRIPTION IC MODULE U204 PAD 1 GND4 Connected to Ground. PAD 2 GND3 Connected to Ground. 14 3 MS1 Connected to Ground. PAD 4 GND0 Connected to Ground. 13 5 MS0 Connected to Ground. 6 NC2 No Connection. PAD 7 GND20 Connected to Ground. PAD 8 GND12 Connected to Ground. PAD 9 GND13 Connected to Ground. PAD 10 GND17 Connected to Ground. PAD 11 GND5 Connected to Ground. 8 12 1 ON ACH0 ADC Input, Channel #0. When U204:1 “ON” - Connected to VR1 on EVB3 9 13 2 ON ACH1 ADC Input, Channel #1. When U204:2 “ON” - Connected to VR2 on EVB3 10 14 3 ON ACH2 ADC Input, Channel #2. 11 15 4 ON ACH3 ADC Input, Channel #3. 20 NC3 No Connection. 21 NC4 No Connection. 22 18 7 ON P1_4 GPIO P1.4 When U204:7 “ON” - Connected to SW2 on EVB3 23 19 8 ON P1_3 GPIO P1.3 When U204:8 “ON” - Connected to SW1 on EVB3 PAD 20 GND9 Connected to Ground. PAD 21 GND8 Connected to Ground. PAD 22 GND7 Connected to Ground. 24 23 9 ON P1_1 GPIO P1.1 When U204:9 “ON” - Connected to USB_RX on EVB3 7 24 VCC_3V Power Supply Input, See Section 4.1. 26 25 10 ON P1_0 GPIO P1.0 When U204:10 “ON” - Connected to USB_TX on EVB3

Rev C Document No. 0007-05-08-03-001 Page 11 of 19 Table 6 - ZICM2410 / EVB3 Connections, U205 PIN # U205 POSITION MODULE PIN NAME DESCRIPTION IC MODULE U205 27 26 1 ON P3_7 GPIO P3.7 When U205:1 “ON” - Connected to SPI Bus on EVB3 28 27 2 ON P3_6 GPIO P3.6 When U205:2 “ON” - Connected to SPI Bus on EVB3 29 28 3 ON P3_5 GPIO P3.5 When U205:3 “ON” - Connected to SPI Bus on EVB3 30 29 4 ON P3_4 GPIO P3.4 When U205:4 “ON” - Connected to SPI Bus on EVB3 30 GND10 Connected to Ground. 31 31 5 ON P3_3 GPIO P3.3 When U205:5 “ON” - Connected to SW4 on EVB3 32 32 6 ON P3_2 GPIO P3.2 When U205:6 “ON” - Connected to SW3 on EVB3 33 GND11 Connected to Ground. 33 34 7 ON P3_1 GPIO P3.1 When U205:7 “ON” - Connected to SPI Bus on EVB3 35 35 8 ON P3_0 GPIO P3.0 When U205:8 “ON” - Connected to LED4 on EVB3 36 GND6 Connected to Ground. 36 37 9 ON P0_7 GPIO P0.7 When U205:9 “ON” - Connected to I2S Bus on EVB3 37 38 10 ON P_06 GPIO P0.6 When U205:10 “ON” - Connected to I2S Bus on EVB3

Rev C Document No. 0007-05-08-03-001 Page 12 of 19 Table 7 - ZICM2410 / EVB3 Connections, U203 PIN # U203 POSITION MODULE PIN NAME DESCRIPTION IC MODULE U203 38 39 10 ON P0_5 GPIO P0.5 When U203:10 “ON” - Connected to I2S Bus on EVB3 39 40 9 ON P0_4 GPIO P0.4 When U203:9 “ON” - Connected to I2S Bus on EVB3 40 41 8 ON P0_3 GPIO P0.3 When U203:8 “ON” - Connected to LED1 on EVB3 41 42 7 ON P0_2 GPIO P0.2 When U203:7 “ON” - Connected to LED2 on EVB3 42 43 6 ON P0_1 GPIO P0.1 When U203:6 “ON” - Connected to LED3 on EVB3 43 44 5 ON P0_0 GPIO P0.0 When U203:5 “ON” - Connected to I2S Bus on EVB3 19 45 4 ON DVDD_1_5 1.5 Volt Regulated Output, Digital Plane. 15 46 3 ON ISP ISP Mode Select When U203:3 “ON” - Connected to SW7 on EVB3 17 47 2 ON RESET# When U203:2 “ON” - Connected to SW5 on EVB3 6 48 1 ON AVDD_1_5 1.5 Volt Regulated Output, Analog Plane. 49 GND14 Connected to Ground. 50 GND15 Connected to Ground. 51 GND16 Connected to Ground. 52 GND18 Connected to Ground. 53 GND19 Connected to Ground. 54 NC1 No Connection. 55 GND1 Connected to Ground. 56 GND2 Connected to Ground.

Rev C Document No. 0007-05-08-03-001 Page 13 of 19 4 ON BOARD RESOURCES 4.1 POWER SUPPLY The three position slide switch (SW6) operates in accordance with the settings given in Table 8. The Power Indicator LED (red) illuminates when power is applied to the evaluation board through any of the methods. Table 8 – EVB3 Power Switch Settings # Power Switch Position VCC Power Supply Value Comments Switch Position 1 VREG VUSB: 5.0 V DC Jack: 5.0 – 9.0 V In this position the evaluation board and module are either powered from the USB interface or through the DC Jack from an external supply. 2 VBAT 3.0 V In this position the evaluation board and module are powered from the two 1.5 V Type AA batteries. 3 VREG + J4 ZIC2410-EVB3: 5 V ZICM2410: 2.1 – 3.0V In this position the evaluation board is powered via either the USB interface or through the DC Jack. The ZICM2410 module is powered externally via the J4 header. See the “ZICM2410-EVB3 Evaluation Board Hardware Reference Guide” for further details. NOTE #1: At power-on, the evaluation board preforms an initialization routine (approximately 1 second) during which all the LEDs (LED1 through LED4) are illuminated. Once the initialization routine has completed the LEDs are turned off. NOTE #2: If batteries are loaded into the holder and the board also has power applied via the USB or DC Jack, and the Power Switch is toggled between the VBAT and either of the VREG postions the device may get stuck in the initialization routine. If this occurs, simply press the RESETB button. 4.2 RESET The ZICM2410-EVB3, by default, has the switch labeled ‘RESETB’ (SW5) connected to the ‘RESET#’ pin of the ZICM2410 module. When pressed, the ZIC2410 will be reset. Using the isolation DIP switches (U203:2), SW5 can be disconnected and external circuitry added. Figure 3 – Photo, RESETB Push Button (SW5) 4.3 ISP SWITCH The 2-position slide switch (SW7) controls the mode of operation, as shown in Figure 4. The ZIC2410 can be placed into either ‘ISP’ or ‘NORMAL’ mode. When placed into ISP mode, the ZIC2410 is configured for the programming of the internal Flash memory (i.e. a firmware upgrade). In order to enter ISP mode, the slider switch must be set to ‘ISP’ and then power applied to the device (alternatively, if power has already been applied the ‘RESETB’ pushbutton

Rev C Document No. 0007-05-08-03-001 Page 14 of 19 may be pressed and released after the slider switch has been set). In order to return to ‘NORMAL’ mode after programming has completed, simply slide the slider switch to ‘NORMAL’ and press and release the ‘RESETB’ pushbutton. Figure 4 – Photo, ISP Switch 4.4 POWER HEADER (J4) This header allows the powering of the ZICM2410 module directly (bypassing the regulator) through Pin #3 and allows the monitoring of the module’s supply line through Pin #4 (SENSE+). Table 9 – Power Header (J4) Pin Out Pin 1 Pin 2 Pin 3 Pin 4 GND (SENSE–) GND Module (Supply) VCC Module (Supply) VCC Module (SENSE+) 4.5 LEDs Figure 5 - Photo, LEDs The ZICM2410-EVB3 includes four colored LEDs. They are connected to various GPIOs of the ZICM2410 module through an inverter as shown in Figure 6. To turn on a LED, the corresponding GPIO pin must be set high. To turn off a LED, the GPIO pin must be cleared (set low). Table 10 – LED Colors and Connections LED # Color GPIO LED # Color GPIO LED 1 White Port 0[3] LED 3 Green Port 0[1] LED 2 Amber Port 0[2] LED 4 Blue Port 3[0] Figure 6 – Drawing, LEDs Schematic

Rev C Document No. 0007-05-08-03-001 Page 15 of 19 4.6 PUSHBUTTON SWITCHES Figure 7 – Photo, Pushbutton Switches When a pushbutton switch is pressed, the corresponding GPIO is pulled low. When released (or not pressed), the GPIO is pulled high. The pushbutton switches correspond to the GPIOs as listed in Table 11. Switch #3 and #4 are dual purpose, as they can also be used as the External Interrupts (INT0 and INT1) inputs for the embedded processor. Table 11 – Pushbutton Switch Connections SWITCH # GPIO SWITCH # GPIO 1 Port 1[3] 3 Port 3[2] 2 Port 1[4] 4 Port 3[3] 4.7 EXTERNAL MEMORY To store non-volatile data, the ZICM2410-EVB3 provides an on-board external SPI Flash memory connected to the Serial Peripheral Interface (SPI) of the ZIC2410. The external memory is required when performing Over-the-Air programming. Using the isolation DIP switches, the memory can be easily disconnected from the ZIC2410. Figure 8 details the connection details below. Figure 8 – Drawing, External Memory Circuit 4.8 VOICE CODEC The ZICM2410-EVB3 has an on-board mono CODEC with speaker driver to support wireless audio and voice. The primary purpose of the external chip is to perform the analog-to-digital and digital-to-analog conversions. The CODEC is configured using the SPI interface while the audio / voice data uses the ZIC2410’s I2S interface. 4.9 HEADPHONE / MICROPHONE JACKS The ZICM2410-EVB3 is equipped with two 3.5 mm jacks, one for headphones and one for a microphone input. The evaluation board has been optimized for headphones with 32 Ω

Rev C Document No. 0007-05-08-03-001 Page 16 of 19 impedance and single-ended microphones with 2.2 kΩ impedance. 4.10 ADDITIONAL JUMPER FUNCTIONS/CONNECTIONS Table 12 –Functions/Connections of Other Jumpers/Connectors Jumper Pin Function Description J3 Analog Input Pins 4-pin connector 1 ACH0 The four ADC input channels are available on this connector. ACH0 and ACH1 are connected to VR1 and VR2 respectively. 2 ACH1 3 ACH2 4 ACH3 J5 GPIO Port Pins 8-pin connector 1 P0_0 GPIO Port 0, Bit #0 2 P0_1 GPIO Port 0, Bit #1 3 P0_2 GPIO Port 0, Bit #2 4 P0_3 GPIO Port 0, Bit #3 5 P0_4 GPIO Port 0, Bit #4 6 P0_5 GPIO Port 0, Bit #5 7 P0_6 GPIO Port 0, Bit #6 8 P0_7 GPIO Port 0, Bit #7 J9 Current Monitor 2-pin connector 1 VCC_MODULE When this jumper is removed a DC current meter can be inserted to monitor the current of the evaluation board 2 VCC J11 GPIO Port Pins 8-pin connector 1 P1_0 GPIO Port 1, Bit #0 2 P1_1 GPIO Port 1, Bit #1 3 N / C No Connection 4 P1_3 GPIO Port 1, Bit #3 5 P1_4 GPIO Port 1, Bit #4 6 N / C No Connection 7 P1_6 or N / C GPIO Port 1, Bit #6 – No Connection on ZICM2410P2 Evaluation Boards 8 P1_7 or N / C GPIO Port 1, Bit #7 – No Connection on ZICM2410P2 Evaluation Boards J14 GPIO Port Pins 8-pin connector 1 P3_0 GPIO Port 3, Bit #0 2 P3_1 GPIO Port 3, Bit #1 3 P3_2 GPIO Port 3, Bit #2 4 P3_3 GPIO Port 3, Bit #3 5 P3_4 GPIO Port 3, Bit #4 6 P3_5 GPIO Port 3, Bit #5 7 P3_6 GPIO Port 3, Bit #6 8 P3_7 GPIO Port 3, Bit #7 J200 Speaker Driver Output 2-pin connector 1 SPKOUTP Speaker Output Positive 2 SPKOUTN Speaker Output Negative

Rev C Document No. 0007-05-08-03-001 Page 17 of 19 5 REVISION HISTORY Revision Date Description A 11Jun09 Released B 18Sep09 Updated to support the use of a ZICM2410P2 module on the EVB3 evaluation board. C 24Sep10 Removed references to ZigBee.

Rev C Document No. 0007-05-08-03-001 Page 18 of 19 APPENDIX-1: SCHEMATIC OF ZICM2410-EVB3 (CEL Doc # 0007-01-01-03-001 Issue ES3-X2) Figure 9 – Diagram, ZICM2410-EVB3 Schematic ES3-X2 ZICM2410 EVAL BD ASSEMBLY SCHEMATIC C Sept 6, 2008 ISSUE Drawing Title: Size Document Number Date: Sheet of 1 1 Push Buttons LEDs Reset Button Power ON ZIC 2410 Module Land SENSE+ SENSE- B C D 5 4 3 2 1 D C B A 2 3 4 5 0007-01-01-03-001 SPI FLASH 09/06/08 REVISION RECORD DESCRIPTION: DATE: ISSUE PRELIMINARY ES ES1 REVISED PER ECR#000022 11/12/08 TX ENABLE RX ENABLE Audio Codec Headphone Jack Microphone Jack INT0 / Switch 3 INT1 / Switch 4 ACH_2 ACH_3 P17 P16 V = 3.0V nominal 1: VCC, VCC_MODULE = VREG 2: VCC, VCC_MODULE = VBAT 3: VCC = VREG, VCC_MODULE = J4 ES2 ES3-X0 ES3-X1 REVISED PER SPREADSHEET 03/23/09 REVISED PER ECR#000027 12/10/08 01/14/09 ES3-X2 04/03/09 REVISED PER SPREADSHEET REVISED PER ECR#000036 1 MH2 R6 390 D1 LNJ026 PCB1 0007-01-04-03-001 PCB 1 MH3 1 MH1 D5 POWER LNJ214 TP138 C52 10nF GND_4 GND_3 GND_13 GND_17 GND_5 P3_7 GND_MS1 P3_5 P3_4 ACH0 ACH1 ACH2 ACH3 GND_0 GND_MS0 NC2 GND_20 GND_12 P1_7 P1_6 P1_4 P1_3 GND_9 GND_8 GND_7 P1_1 VCC_3V P1_0 P3_6 GND_10 P3_3 P3_2 GND_11 P3_1 P3_0 GND_6 P0_7 P0_6 P0_5 P0_4 P0_3 P0_2 P0_1 P0_0 DVDD_1_5 ISP RESET AVDD_1_5 GND_14 GND_15 GND_16 GND_18 GND_19 NC1 GND_1 CW 1 2 3 VR1/SPKR-VOL D2 LNJ414 D3 LNJ326 D4 LNJ926 R7 390 R8 390 R9 390 1 MH4 GND_2 D11 D13 1 2 3 J7 + - BC2 2462 C9 47uF 6.3WVDC C12 10nF 1 2 J9 HDR_2X1 C8 4.7uF SW1 B3S-1100P SW2 B3S-1100P SW5 B3S-1100P 1 2 3 4 J3 1 2 3 4 J4 1 2 3 4 5 6 7 8 J5 22-10-2081 1 MH5 1 MH6 1 2 3 4 5 6 7 8 J11 22-10-2081 1 2 3 4 5 6 7 8 J14 22-10-2081 1 2 3 SW7 SW/SPDT APEM SLB12814 R1 33 C1 NP C2 NP 1 MH7 1 MH8 1 MH9 1 MH10 1 MH11 1 MH12 1 MH13 1 MH14 1 MH15 1 MH16 1 MH17 SW3 B3S-1100P SW4 B3S-1100P DVDD_1R5 AVDD_1R5 R5 33 R15 33 CW 1 2 3 VR2/MIC-VOL 1 DCD 2 RI 3 GND 4 D+ 5 D- 6 VDD 7 REGIN 8 VBUS 9 RST 10 NC 11 SUSPEND 12 SUSPEND 13 NC 14 NC 15 NC 16 NC 17 NC 18 NC 19 NC 20 NC 21 NC 22 NC 23 CTS 24 RTS 25 RXD 26 TXD 27 DSR 28 DTR U10 CP2102 C25 .1uF 1 /CS 2 SO 3 /WP 4 GND 5 SI 6 SCK 7 /HOLD 8 VCC U8 AT25FS010N JMP1 929955-06 JMP SCREW1 4-40 X 5/16" SCREW2 4-40 X 5/16" NUT1 4-40 NUT NUT2 4-40 NUT STANDOFF1 27FSTP00500 STANDOFF2 27FSTP00500 STANDOFF3 27FSTP00500 STANDOFF4 27FSTP00500 1 MICBIAS 2 AVDD 3 AGND 4 DCVDD 5 DBVDD 6 DGND 7 ADCDAT 8 DACDAT 9 FRAME 10 BCLK 11 MCLK 12 CSB/GPIO 13 SCLK 14 SDIN 15 MODE 16 MONOOUT 17 SPKOUTP 18 SPKGND 19 SPKOUTN 20 SPKVDD 21 AUX 22 VMID 23 MICN 24 MICP 25 GND_BOTTOM U200 WM8974/QFN24 1 2 J200 HDR_2X1 C6 1uF C11 1uF C16 1uF R14 2.2K R20 NP C17 NP SW9 1 3 11 10 2 SW11 R23 0 OHM R24 0 OHM ON ON ON ON ON ON ON ON ON OFF OFF OFF OFF OFF OFF OFF OFF OFF ON OFF 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 U203 ON ON ON ON ON ON ON ON ON OFF OFF OFF OFF OFF OFF OFF OFF OFF ON OFF 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 U204 ON ON ON ON ON ON ON ON ON OFF OFF OFF OFF OFF OFF OFF OFF OFF ON OFF 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 U205 7 GND 14 VCC 1 A0 3 A1 5 A2 13 A3 11 A4 9 A5 2 O0 4 O1 6 O2 12 O3 10 O4 8 O5 U4 74LVC04-SO14 R2 10K R10 10K R17 10K R18 10K C27 4.7uF C18 4.7uF C19 4.7uF C20 4.7uF C23 4.7uF C28 4.7uF + C30 220µF C24 .1uF 1 ADJ 2 VOUT1 3 VIN 4 VOUT2 U206 R28 165 R29 121 C33 4.7uF C32 4.7uF C29 220pF 1 VUSB 2 DATA- 3 DATA+ 4 GND 5 SHIELD1 6 SHIELD2 J1 USB-B C5 .1uF C26 .1uF C40 .1uF C15 4.7uF C4 1uF C22 1uF C31 1uF C53 1uF R19 33 R21 33 R25 33 R26 33 R11 390 R12 10K R13 10K R22 10K R3 10K R4 10K R16 10K R30 680 NP 1 2 3 4 C 1A 2A 4A CA 3A SW6 D6 TVS_DUAL_SOT23_300W_5V_ONS R27 12 DUT1 0007-00-00-00-001 DUT R31 10K R32 10K VCC RESET GND GND GND RESET MS2 ACH_0 ACH_1 GND VUSB GND GND GND GND GND GND GND GND GND GND VCC_MODULE_SENSE GND MS2 P33 P32 P10 GND P11 VCC P34 P37 P36 P35 GND GND GND GND VCC VCC P31 P36 P35 P07 GND GND VCC P00 P01 P02 P03 P04 P05 P10 P11 P13 P14 ACH_1 ACH_0 P36 P37 P35 P34 P33 P32 P31 P30 P07 P06 P13 P14 GND GND VCC P03 P02 P01 P30 GND GND GND GND GND P05 P00 P06 P04 GND GND GND VCC_MODULE VCC_MODULE VCC_MODULE VCC_MODULE GND VCC_MODULE VCC_MODULE_SENSE VCC_MODULE VUSB GND GND GND GND VCC VCC VCC_MODULE GND VCC VCC

Rev C Document No. 0007-05-08-03-001 Page 19 of 19 APPENDIX-2: BILL OF MATERIALS (ZICM2410-EVB3) (CEL Doc # 0007-01-02-03-001 Issue ES-X3) This document is subject to revision without notification. Table 13 – BOM, ZICM2410-EVB3