Cisco TelePresence System Codec C90 Manual 

Physical interface guide D14644.03 Codec C90 Physical Interface Guide TC4.1, February 2011. © 2010-2011 Cisco Systems, Inc. All rights reserved. www.cisco.com The Physical Interface Guide Cisco Telepresence System Codec C90 Software version TC4 FEBRUARY 2011

Physical interface guide D14644.03 Codec C90 Physical Interface Guide TC4.1, February 2011. © 2010-2011 Cisco Systems, Inc. All rights reserved. www.cisco.com TA - ToC - Hidden text anchor Table of Contents Introduction About this guide................................................................... 4 User documentation......................................................... 4 Connecting to the codec Basic setup when connecting to Codec C90...................... 6 The physical interface The front panel..................................................................... 8 Rear panel sockets overview............................................... 9 The Video Input Matrix....................................................... 10 About the matrix............................................................. 10 Configure the video inputs............................................. 10 The Advanced configuration menu............................ 10 The API commands.................................................... 10 The default values....................................................... 10 Video inputs........................................................................11 Component 1–2 (Y-Pr-Pb)...............................................11 HD-SDI 1–4......................................................................11 Composite 5 / S-Video (YC) 5........................................11 HDMI 1–4.........................................................................12 DVI-I 3 and 5...................................................................12 Video input formats.........................................................13 4 x HDMI inputs, supported formats............................13 4 x HD-SDI inputs, supported formats........................13 2 x DVI-I inputs, supported formats............................13 2 x YPbPr inputs, supported formats..........................13 1 x S-Video/Composite input, supported formats......13 Video outputs......................................................................14 HDMI 1 and 3...................................................................14 DVI-I 2 and 4...................................................................14 Composite 5....................................................................14 Video output formats.......................................................14 2 x HDMI and 2 x DVI-I outputs, supported formats...14 1 x Composite output, supported formats..................14 Levels..............................................................................14 Audio inputs....................................................................... 15 Microphone/Line In 1–8 (XLR)........................................ 15 HDMI In 3, 4.................................................................... 15 Line In 1–4 (RCA)............................................................ 16 Audio outputs......................................................................17 Line Out 5–6 (XLR)..........................................................17 HDMI Out 1, 3..................................................................17 Line Out 1–4 (RCA)......................................................... 18 Audio signal levels tables................................................... 19 Audio hardware information table...................................... 20 Volume control table.......................................................... 20 Network connectors........................................................... 21 Ethernet interface........................................................... 21 COM port and Camera Control port.................................. 22 COM port........................................................................ 22 Camera Control port...................................................... 22 Power ................................................................................ 23 Power socket.................................................................. 23 Power switch.................................................................. 23 Chassis grounding.......................................................... 23 GPIO and other connectors............................................... 24 GPIO............................................................................... 24 USB................................................................................ 24 T Link.............................................................................. 24 What’s in this guide? The top menu bar and the entries in the Table of Contents are all hyperlinks, just click on them to go to the topic. We recommend you visit our web site regularly for updated versions of the user documentation. Go to: http://www.cisco.com/go/telepresence/ docs - and navigate in the right pane to find the TelePresence product documentation.

Physical interface guide D14644.03 Codec C90 Physical Interface Guide TC4.1, February 2011. © 2010-2011 Cisco Systems, Inc. All rights reserved. www.cisco.com Chapter 1 Introduction

Physical interface guide D14644.03 Codec C90 Physical Interface Guide TC4.1, February 2011. © 2010-2011 Cisco Systems, Inc. All rights reserved. www.cisco.com About this guide The purpose of this document is to describe the physical interface for the Codec C Series listed below.: • Cisco TelePresence System Codec C90 User documentation The user documentation for the Cisco TelePresence systems, running the TC software, have several guides suitable to various user groups. • Video conference room primer • Video conference room acoustics guidelines • Installation guides for the TelePresence systems • Software release notes for the TC software • Getting started guide for the TelePresence systems • User guide for the TelePresence systems • When using the Touch controller, ref. TC4.1 version of the user guide • When using the Remote Control, ref. TC4.0 version of the user guide • Quick reference guides for the TelePresence systems • Administrator guides for the TelePresence systems • Camera user guide for the PrecisionHD cameras • API reference guides for the Codec C Series • TC Console user guide for the Codec C Series • Physical interfaces guides for the Codec C Series • Regulatory compliance and safety information guides • Legal & license information for products using TC software Download the user documentation Go to: http://www.cisco.com/go/telepresence/docs - in the right pane, select: • TelePresence Peripherals for the PrecisionHD cameras, microphones, Touch unit, and remote controls. • TelePresence Solutions Platform for the Codec C Series and Quick Set C20. Software download Go to: http://www.cisco.com/cisco/software/navigator.html

Physical interface guide D14644.03 Codec C90 Physical Interface Guide TC4.1, February 2011. © 2010-2011 Cisco Systems, Inc. All rights reserved. www.cisco.com Chapter 2 Connecting to the codec

Physical interface guide D14644.03 Codec C90 Physical Interface Guide TC4.1, February 2011. © 2010-2011 Cisco Systems, Inc. All rights reserved. www.cisco.com ! LAN/ Ethernet Monitor (Audio from HDMI 1 or Line Out 1–2) OPTIONAL: Loudspeakers Basic setup when connecting to Codec C90 The illustration shows you the basic setup when connecting the monitor, PC, camera, microphone, loudspeakers (if applicable), LAN and line voltage to your codec. Make sure the codec has been switched off and disconnected from the line voltage whenever connecting or disconnecting other equipment. OPTIONAL: Dual monitor setup Connect the second monitor to HDMI 3 Main camera: Video from PrecisionHD 1080p OPTIONAL: You may connect additional microphones Video from PC OPTIONAL: You may connect a second camera. (extra camera not included). Extra camera will require separate power supply and control cabling. Consult the documentation supplied with the extra camera for details. Main camera: Camera Control to PrecisionHD 1080p Microphone OPTIONAL: Audio from PC Mains Power Cable Inputs Outputs Basic Setup The main connectors for basic setup are highlighted in orange. 1 1 Power Switch First connect the cables, then turn the codec on.

Physical interface guide D14644.03 Codec C90 Physical Interface Guide TC4.1, February 2011. © 2010-2011 Cisco Systems, Inc. All rights reserved. www.cisco.com Chapter 3 The physical interface

Physical interface guide D14644.03 Codec C90 Physical Interface Guide TC4.1, February 2011. © 2010-2011 Cisco Systems, Inc. All rights reserved. www.cisco.com The front panel There are four LED’s in the front of the Codec: • Power – The POWER LED turns ON when power is connected, otherwise OFF • Call – The CALL LED turns ON when there are active calls on the codec, otherwise OFF • Infrared – The IR LED flashes when infrared signals are received • Alarm – The ALARM LED turns ON when there is no connection to the network, otherwise OFF Power Call IR Alarm (infrared)

Physical interface guide D14644.03 Codec C90 Physical Interface Guide TC4.1, February 2011. © 2010-2011 Cisco Systems, Inc. All rights reserved. www.cisco.com Codec C90 Rear Panel Audio sockets Video sockets Network interface sockets Power socket Power switch COM Port, Camera Control Audio sockets Video sockets GPIO and USB Rear panel sockets overview The Codec C90 provides great flexibility for the connection of audio and video equipment. The illustration below shows the rear panel of the Codec C90. Video sockets The video input sockets comprise: 4xHDMI 4xHD-SDI 2xDVI-I 2xAnalog Component (Y-Pr-Pb) 1xComposite or 1xS-Video(YC) The video output sockets comprise: 2xHDMI 2xDVI-I 1 Composite Audio sockets The audio input sockets comprise: 8xXLR Female - Microphone/Line In 4xRCA - Line In (1 Left, 2 Right, 3 Left, 4 Right) 2xHDMI The audio output sockets comprise: 2xXLR Male - Line Out 4xRCA - 1 Left (SPDIF), 2 Right, 3 Left (SPDIF), 4 Right 2xHDMI Other sockets The other sockets comprise: Ethernet 1 and Ethernet 2 COM - Serial data port Camera control, serial port Power socket Grounding - Chassis grounding Power On/Off switch GPIO–General purpose Input/Output USB Host*, USB Device*, T Link* The following pages give a detailed description of the rear panel sockets and connectors. * For future use T Link Inputs Outputs Basic Setup The main connectors for basic setup are highlighted in orange. 1 1

Physical interface guide D14644.03 Codec C90 Physical Interface Guide TC4.1, February 2011. © 2010-2011 Cisco Systems, Inc. All rights reserved. www.cisco.com The Video Input Matrix The video input matrix is found at the underside side of the codec. The matrix illustrates the combinations in which the video inputs can be connected. About the matrix Only one video input source from each row can be active at any time. The numbers in the left column represents the Video Input Sources 1–5. The main connectors, which are used in basic setup, are marked in orange color on the codec. Note that the Comp. 5 and S-Video (YC) 5 inputs uses the same physical connectors and can not be connected at the same time. Configure the video inputs You can configure the video input settings from the Advanced configuration menu or by running API commands. The Advanced configuration menu Go to the on screen menu to configure the video input sources. • Navigate to: Settings > Advanced > Advanced Configuration > Video > Input > Source 1. Configure the video input connectors, quality and name. See the video input matrix. Only one video input source from each row in the matrix, can be active at any time. • Navigate to: Settings > Advanced > Advanced Configuration > Video > MainVideoSource. Configure the main video source. • Navigate to: Settings > Advanced > Advanced Configuration > Video > DefaultPresentationSource. Configure the default presentation source. The API commands Open a telnet or ssh session, to the codec, to issue the API commands. Configure the video input connectors. See the video input matrix. Only one video input source from each row in the matrix, can be active at any time: • xconfiguration video input source 1 connector: hdmi • xconfiguration video input source 2 connector: hdmi • xconfiguration video input source 3 connector: dvi • xconfiguration video input source 4 connector: hdmi • xconfiguration video input source 5 connector: dvi Configure the video quality and define a name of the video inputs 1 to 5: • xconfiguration video input source 1 quality: motion • xconfiguration video input source 1 name: “Main Camera“ Configure the main video source. Here, the main video source is the camera, connected to video input source 1: • xconfiguration video mainvideosource: 1 Configure the default presentation source. Here, the default presentation source is a PC, and the PC is connected to video input source 3 connector: • xconfiguration video defaultpresentationsource: 3 The default values • Video Input Source 1 Connector: HDMI • Video Input Source 2 Connector: HDMI • Video Input Source 3 Connector: DVI • Video Input Source 4 Connector: HDMI • Video Input Source 5 Connector: DVI • Video Input Source 1 Name: “Main Camera“ • Video Input Source 2 Name: “Secondary Camera“ • Video Input Source 3 Name: “PC“ • Video Input Source 4 Name: “DVD“ • Video Input Source 5 Name: “Document Camera“ • Video Input Source 1 Quality: Motion • Video Input Source 2 Quality: Motion • Video Input Source 3 Quality: Sharpness • Video Input Source 4 Quality: Motion • Video Input Source 5 Quality: Sharpness • Video MainVideoSource: 1 • Video DefaultPresentationSource: 3 Video input matrix Input Sources Connector Name 1 1st Camera HDMI 1 HD-SDI 1 YPrPb 1 2 2nd Camera HDMI 2 HD-SDI 2 YPrPb 2 3 PC HDMI 3 HD-SDI 3 DVI-I 3 4 HDMI 4 HD-SDI 4 – 5 DVI-I 5 Comp. 5 YC 5

Physical interface guide D14644.03 Codec C90 Physical Interface Guide TC4.1, February 2011. © 2010-2011 Cisco Systems, Inc. All rights reserved. www.cisco.com Video inputs All video inputs can not be active at the same time. Please refer to the Video Input Matrix on the previous page to see an overview. Component 1–2 (Y-Pr-Pb) 2 x 3 BNC sockets, analog video input 1, 2. There are three BNC connectors for each Component interface; Y (luma), Pr (red), Pb (blue). Typical use: Camera, DVD and Content player. HD-SDI 1–4 4 x BNC sockets, digital video input 1, 2, 3, 4. Typical use: Cameras. Composite 5 / S-Video (YC) 5 2 x BNC sockets, analog video input 5. The S-Video (YC) and the composite inputs uses the same physical connectors, and will not be able to be connected at the same time. • S-Video 5 - Connect to the Y/Comp 5 (luma) and C 5 (chroma) connectors • Composite 5 - Connect to Comp 5 connector Typical use: Camera and DVD. Levels HD-SDI 0.8 Vpp, 75 Ω SMPTE 259M (270 Mbps) SMPTE 292M (1.485, 1.485/1.001 Gbps) Y-Pb-Pr Y: 1V Vpp, 75 Ω Pb: 0.7 Vpp, 75 Ω Pr: 0.7 Vpp, 75 Ω Composite. 1 Vpp, 75  Ω S-Video (YC) Y: 1 Vpp, 75 Ω C (PAL): 0.3 Vpp, 75 Ω C (NTSC): 0.28 Vpp, 75 Ω BNC pin-out External view of socket GND Signal 2xComponent In (YPrPb) 1xComposite or 1xS-Video (YC) 4xHD-SDI In BNC: Bayonet Neill-Concelman HD-SDI: High Definition - Serial Digital Interface Y-Pr-Pb: Y: Information about luma (luminance); Pr: Red color; Pb: Blue color Y-C: Y: Information about luma (luminance); C: Information about chroma (color)

Physical interface guide D14644.03 Codec C90 Physical Interface Guide TC4.1, February 2011. © 2010-2011 Cisco Systems, Inc. All rights reserved. www.cisco.com HDMI Pin-out Pin Assignment Pin Assignment 1 T.M.D.S. Data 2+ 11 T.M.D.S. Clock Shield 2 T.M.D.S. Data 2 Shield 12 T.M.D.S. Clock– 3 T.M.D.S. Data 2­– 13 CEC 4 T.M.D.S. Data 1 14 Reserved (N.C. on device) 5 T.M.D.S. Data 1 Shield 15 SCL 6 T.M.D.S. Data 1­– 16 SDA 7 T.M.D.S. Data 0 17 DDC/CEC Ground 8 T.M.D.S. Data 0 Shield 18 +5 V Power (max 50 mA) 9 T.M.D.S. Data 0– 19 Hot Plug Detect 10 T.M.D.S. Clock+ Pin: 19 17 3 1 Pin: 18 16 4 2 HDMI pin-out External view of socket 4xHDMI In 2xDVI-I In Video inputs, continued... All video inputs can not be active at the same time. Please refer to the Video Input Matrix (two pages back) to see an overview. HDMI 1–4 4 x HDMI sockets, digital video input 1–4. Audio input on 3 and 4. HDMI - High Definition Multimedia Interface (digital, sound & picture) Typical use: Camera, DVD, PC. Main connector. The HDMI 1 input is the main connector to the PrecisionHD 1080p camera. DVI-I 3 and 5 2 x DVI-I sockets, digital/analog video input 3, 5. • DVI-D • DVI-A (Analog RGB/VGA) • DVI-A Analog component/YPbPr DVI-I - Digital Video Interface - Integrated (digital DVI-D and analog DVI-A) Typical use: Two digital video inputs for PC presentations or used for the PrecisionHD camera. Main connector. The DVI-I 3 is the main connector for PC input. DVI-I pin-out External view of socket

Physical interface guide D14644.03 Codec C90 Physical Interface Guide TC4.1, February 2011. © 2010-2011 Cisco Systems, Inc. All rights reserved. www.cisco.com Video input formats 4 x HDMI inputs, supported formats • 1920 x 1080@60, 59.94 Hz (1080p60) • 1920 x 1080@50 Hz (1080p50) • 1920 x 1080@30, 29.97 Hz (1080p30) • 1920 x 1080@25 Hz (1080p25) • 1920 x 1080@24, 23.97 Hz (1080p24) • 1920 x 1200@50 Hz (WUXGA) • 1680 x 1050@60 Hz (WSXGA+) • 1600 x 1200@50, 60 Hz (UXGA) • 1440 X 900@60 Hz (WXGA+) • 1400 x 1050@60, 75 Hz • 1366 x 768@60 Hz • 1360 x 768@60 Hz • 1280 x 1024@60, 75, 85 Hz (SXGA) • 1280 x 960@60, 85 Hz • 1280 x 800@60 Hz (WXGA) • 1280 x 768@60, 75, 85 Hz (WXGA) • 1280 x 720@60, 59.94 Hz (720p60) • 1280 x 720@50 Hz (720p50) • 1152 x 864@75 Hz • 1024 x 768@60, 70, 75, 85 Hz (XGA) • 848 x 480@60 Hz • 800 x 600@56, 60, 72, 75, 85 Hz (SVGA) • 720 x 576@50 Hz (576p50) • 720 x 480@60, 59.94 Hz (480p60) • 640 x 480@60, 72, 75, 85 Hz (VGA) 4 x HD-SDI inputs, supported formats • 1920 x 1080@30 Hz (1080p30) • 1920 x 1080@25 Hz (1080p25) • 1280 x 720@60 Hz (720p60) • 1280 x 720@50 Hz (720p50) • 1280 x 720@30 Hz (720p30) • 1280 x 720@25 Hz (720p25) 2 x DVI-I inputs, supported formats Digital (DVI-D) • Same as HDMI inputs, ref. above. Analog RGB (DVI-A) • 1920 x 1080@60 Hz (1080p60) • 1920 x 1200@50 Hz (WUXGA) • 1680 x 1050@60 Hz (WSXGA+) • 1600 x 1200@60 Hz (UXGA) • 1440 x 900@60 Hz (WXGA+) • 1400 x 1050@60, 75 Hz • 1366 x 768@60 Hz • 1360 x 768@60 Hz • 1280 x 1024@60, 75, 85 Hz (SXGA) • 1280 x 960@60, 85 Hz • 1280 x 800@60 Hz (WXGA) • 1280 x 768@60, 75, 85 Hz (WXGA) • 1280 x 720@60 Hz (720p60) • 1152 x 864@75 Hz • 1024 x 768@60, 70, 75, 85 Hz (XGA) • 848 x 480@60 Hz • 800 x 600@56, 60, 72, 75, 85 Hz (SVGA) • 720 x 576@50 Hz • 720 x 480@60, 59.94 Hz (480p60) • 640 x 480@60, 72, 75, 85 Hz (VGA) Analog YPbPr (DVI-A) • Same as YPbPr inputs, ref. below. Extended Display Identification Data (EDID) 2 x YPbPr inputs, supported formats • 1920 x 1080@60 Hz (1080p60) • 1920 x 1080@50 Hz (1080p50) • 1920 x 1080@30 Hz (1080p30) • 1920 x 1080@25 Hz (1080p25) • 1280 x 720@60 Hz (720p60) • 1280 x 720@50 Hz (720p50) • 1280 x 720@30 Hz (720p30) • 720 x 576@50 Hz (576p50) • 720 x 480@60 Hz (480p60) 1 x S-Video/Composite input, supported formats • PAL/NTSC

Physical interface guide D14644.03 Codec C90 Physical Interface Guide TC4.1, February 2011. © 2010-2011 Cisco Systems, Inc. All rights reserved. www.cisco.com Video output formats 2 x HDMI and 2 x DVI-I outputs, supported formats • 1920 x 1080@60 Hz (1080p60) • 1920 x 1200@60Hz (WUXGA) • 1600 x 1200@60 Hz (UXGA) • 1366 x 768@60 Hz • 1360 x 768@60 Hz • 1280 x 720@60 Hz (720p60) • 1280 x 1024@60 Hz (SXGA) • 1280 x 768@60 Hz (WXGA) • 1024 x 768@60 Hz (XGA) • 800 x 600@60 Hz (SVGA) • 640 x 480@60 Hz (VGA) VESA Monitor Power Management 1 x Composite output, supported formats BNC Connector • PAL/NTSC Levels Composite. 1 Vpp, 75  Ω Video outputs HDMI 1 and 3 2 x HDMI sockets, digital video and audio output 1, 3. HDMI - High Definition Multimedia Interface (digital, sound & picture). Typical use: Monitor, recording device. Main connector. The HDMI output 1 is the main connector to the monitor. Dual monitor. Dual output is provided on HDMI output 3. DVI-I 2 and 4 2 x DVI-I sockets, digital/analog video output 2, 4. • DVI-D. • DVI-A (Analog RGB / VGA). DVI-I - Digital Video Interface - Integrated (digital DVI-D and analog DVI-A). Typical use: Monitors. Composite 5 1 x BNC sockets, analog video output 5. Typical use: Monitor. BNC pin-out External view of socket GND Signal Pin: 19 17 3 1 Pin: 18 16 4 2 HDMI pin-out External view of socket DVI-I pin-out External view of socket 1xComposite Out 2xDVI-I Out 2xHDMI Please refer to previous page for pin-out scheme. BNC - Bayonet Neill-Concelman

Physical interface guide D14644.03 Codec C90 Physical Interface Guide TC4.1, February 2011. © 2010-2011 Cisco Systems, Inc. All rights reserved. www.cisco.com Audio inputs Unused, but connected audio inputs must be set to Off to avoid unwanted audio/noise. Microphone/Line In 1–8 (XLR) 8 x Balanced XLR sockets, audio input 1–8. Main connector. The Microphone/Line In 1 is the main connector for the microphone. All eight microphone inputs are for balanced electret microphones, 48V phantom powered via XLR connectors. The phantom powering of all eight XLR sockets can be individually switched off. The input will then be a balanced line level input. All Microphone/Line In 1–8 are equipped with acoustic echo canceller. Use Microphone/Line In 1–8 to connect to an external microphone amplifier or an external mixer. Default configuration. In default configuration, all Microphone/Line In inputs are enabled and configured as microphones. HDMI In 3, 4 2 x HDMI connectors, audio input 3, 4 Typical use: Use HDMI In 3 or 4 (2–8 channels) to connect to external playback devices as DVD players. Each input support up to two channels at 48kHz sampling rate. XLR pin-out External view of socket Pin 1: Gnd Pin 2: Hot Pin 3: Cold/neutral 8xMicrophone /Line In 2xHDMI In XLR - Electrical Connector (Cannon XL series with Rubber compound) Pin: 19 17 3 1 Pin: 18 16 4 2 HDMI pin-out External view of socket Please refer to previous page for pin-out scheme. 1 2 3

Physical interface guide D14644.03 Codec C90 Physical Interface Guide TC4.1, February 2011. © 2010-2011 Cisco Systems, Inc. All rights reserved. www.cisco.com Audio inputs, continued... Unused, but connected audio inputs must be set to Off to avoid unwanted audio/noise. Line In 1–4 (RCA) 4 x RCA sockets, audio input 1–4 Audio Line In 1–4 are used when connecting to PC and to external playback devices, such as VCR’s or DVD players. Main connectors. The Line In 1 (left) and Line In 2 (right) are the main connectors to a PC. Stereo. For systems with stereo I/O the audio inputs can be configured in stereo pairs: • Connect the left channel to Line In 1 or 3 • Connect the right channel to Line In 2 or 4 Default configuration for Line In 1–2. In the default configuration Line In 1 and 2 are configured as stereo inputs for external playback devices, such as a PC. Default configuration for Line In 3–4. In the default configuration Line In 3 and 4 are configured as stereo input pairs. The two inputs are paired with Line Out 3 and 4 respectively. This pairing will avoid feedback situations that can arise when playback/recording devices are in standby mode (Loop suppression). Line In 3 and 4 are used with external playback devices as VCR’s and DVD players. RCA - Phono Plug (the Radio Corporation of America) 4xLine In RCA pin-out External view of socket GND Signal

Physical interface guide D14644.03 Codec C90 Physical Interface Guide TC4.1, February 2011. © 2010-2011 Cisco Systems, Inc. All rights reserved. www.cisco.com Audio outputs Line Out 5–6 (XLR) 2 x Balanced XLR sockets, audio output 5–6. Audio Line Out 5–6 are balanced outputs, for connection to balanced speakers. Default configuration. In default configuration Line Out 5 is configured as Left speaker, and Line Out 6 is configured as right speaker. HDMI Out 1, 3 2 x HDMI connectors, audio out 1, 3 Use HDMI Out 1 to connect to a flat screen with speakers. HDMI 1 will provide stereo audio speaker signals at 48kHz. Use HDMI Out 3 to connect to a DVD recorder. HDMI will provide stereo line output signals at 48kHz. Includes local microphones. Main connector. The HDMI output 1 is the main connector to the monitor. HDMI 1. Audio from far end and PC. HDMI 3. All audio mixed together for recordings. XLR pin-out External view of socket Pin 1: Gnd Pin 2: Hot Pin 3: Cold/neutral 2xLine Out (XLR male) XLR - Electrical Connector (Cannon XL series with Rubber compound) What is a Line output A Line output consists of all signals from the local side and all signals from the far end side. What is a Speaker output A Speaker output consists of all signals from the local side, except microphones, and all signals from the far end side. Left channel The Left channel consists of all the Left channel and Mono signals. Right channel The Right channel consists of all the Right channel and Mono signals. 2xHDMI Out 1 2 3

Physical interface guide D14644.03 Codec C90 Physical Interface Guide TC4.1, February 2011. © 2010-2011 Cisco Systems, Inc. All rights reserved. www.cisco.com Audio outputs, continued... Line Out 1–4 (RCA) 4xRCA sockets, audio output 1-4 Can be configured as two stereo pairs. Main connectors. Line Out 1 (left) and Line Out 2 (right) are the main connectors to the local loudspeaker system. The local loudspeaker system may or may not include the DNAM (Digital Natural Audio Module). Default configuration Line Out 1-2. In default configuration, Line Out 1 and 2 are configured as stereo speakers. if a DNAM is present or SPDIF is active on Line Out 1, then Line Out 1 provides a digital stereo speaker signal and Line Out 2 is not active. Default configuration Line Out 3-4. In default configuration, Line Out 3 and 4 are configured as stereo line out for external recording devices as VCR’s or DVD recorders. if a DNAM is present or SPDIF is active on Line Out 3, then Line Out 3 provides a digital stereo speaker signal and Line Out 4 is not active. SPDIF - Sony/Philips Digital Interface, used by the Digital Natural Audio Module. RCA - Phono Plug (the Radio Corporation of America) What is a Line output A Line output consists of all signals from local side and all signals from far end side. What is a Speaker output A Speaker output consists of all signals from local side, except microphones, and all signals from far end side. Left channel The Left channel consists of all Left channel and Mono signals. Right channel The Right channel consists of all Right channel and Mono signals. 4xLine Out RCA pin-out External view of socket GND Signal

Physical interface guide D14644.03 Codec C90 Physical Interface Guide TC4.1, February 2011. © 2010-2011 Cisco Systems, Inc. All rights reserved. www.cisco.com Notes: 1. Default levels are marked with white text on black 2. For the dBu value for input clipping level and absolute max output level, a sine waveform is assumed 3. If numbers in dBV are required, dBV value is 2.2 dB lower than the dBu value. Example: -10 dBu equals -12.2 dBV Line Inputs 1 to 8 XLR female Signal levels Clipping level Nominal level Level setting [dB] [Vpp] [dBu] [dBu] 0.0 34.7 24.0 6.0 1.0 31.0 23.0 5.0 2.0 27.6 22.0 4.0 3.0 24.6 21.0 3.0 4.0 21.9 20.0 2.0 5.0 19.5 19.0 1.0 6.0 17.4 18.0 0.0 7.0 15.5 17.0 -1.0 8.0 13.8 16.0 -2.0 9.0 12.3 15.0 -3.0 10.0 11.0 14.0 -4.0 11.0 9.8 13.0 -5.0 12.0 8.7 12.0 -6.0 13.0 7.8 11.0 -7.0 14.0 6.9 10.0 -8.0 15.0 6.2 9.0 -9.0 16.0 5.5 8.0 -10.0 17.0 4.9 7.0 -11.0 18.0 4,4 6.0 -12.0 19.0 3,9 5.0 -13.0 20.0 3,5 4.0 -14.0 21.0 3,1 3.0 -15.0 22.0 2,8 2.0 -16.0 23.0 2,5 1.0 -17.0 24.0 2,2 0.0 -18.0 Line Inputs 1 to 4 Female RCA/phone Signal levels Clipping level Nominal level Level setting [dB] [Vpp] [dBu] [dBu] 0.0 17.4 18.0 0.0 1.0 15.5 17.0 -1.0 2.0 13.8 16.0 -2.0 3.0 12.3 15.0 -3.0 4.0 11.0 14.0 -4.0 5.0 9.8 13.0 -5.0 6.0 8.7 12.0 -6.0 7.0 7.8 11.0 -7.0 8.0 6.9 10.0 -8.0 9.0 6.2 9.0 -9.0 10.0 5.5 8.0 -10.0 11.0 4.9 7.0 -11.0 12.0 4.4 6.0 -12.0 13.0 3.9 5.0 -13.0 14.0 3.5 4.0 -14.0 15.0 3.1 3.0 -15.0 16.0 2.8 2.0 -16.0 17.0 2.5 1.0 -17.0 18.0 2,2 0.0 -18.0 19.0 2,0 -1.0 -19.0 20.0 1,7 -2.0 -20.0 21.0 1,6 -3.0 -21.0 22.0 1,4 -4.0 -22.0 23.0 1,2 -5.0 -23.0 24.0 1,1 -6.0 -24.0 Microphone Inputs 1 to 8 XLR female Signal levels Clipping level Nominal level Level setting [dB] [mVpp] [dBu] [dBu] 0.0 275.0 -18.0 -36.0 1.0 245.1 -19.0 -37.0 2.0 218.4 -20.0 -38.0 3.0 194.7 -21.0 -39.0 4.0 173.5 -22.0 -40.0 5.0 154.6 -23.0 -41.0 6.0 137.8 -24.0 -42.0 7.0 122.8 -25.0 -43.0 8.0 109.5 -26.0 -44.0 9.0 97.6 -27.0 -45.0 10.0 87.0 -28.0 -46.0 11.0 77.5 -29.0 -47.0 12.0 69.1 -30.0 -48.0 13.0 61.6 -31.0 -49.0 14.0 54.9 -32.0 -50.0 15.0 48.9 -33.0 -51.0 16.0 43.6 -34.0 -52.0 17.0 38.8 -35.0 -53.0 18.0 34,6 -36.0 -54.0 19.0 30,9 -37.0 -55.0 20.0 27,5 -38.0 -56.0 21.0 24,5 -39.0 -57.0 22.0 21,8 -40.0 -58.0 23.0 19,5 -41.0 -59.0 24.0 17,4 -42.0 -60.0 Audio signal levels tables Line outputs 5 to 6 XLR male Signal levels Absolute max output level Nominal level Level setting [dB] [Vpp] [dBu] [dBu] -24.0 2,2 0.0 -18.0 -23.0 2,5 1.0 -17.0 -22.0 2,8 2.0 -16.0 -21.0 3,1 3.0 -15.0 -20.0 3,5 4.0 -14.0 -19.0 3,9 5.0 -13.0 –18.0 4.4 6.0 -12.0 –17.0 4.9 7.0 -11.0 –16.0 5.5 8.0 -10.0 –15.0 6.2 9.0 -9.0 –14.0 6.9 10.0 -8.0 –13.0 7.8 11.0 -7.0 –12.0 8.7 12.0 -6.0 –11.0 9.8 13.0 -5.0 –10.0 11.0 14.0 -4.0 –9.0 12.4 15.0 -3.0 –8.0 13.9 16.0 -2.0 –7.0 15.6 17.0 -1.0 –6.0 17.5 18.0 0.0 –5.0 19.6 19.0 1.0 –4.0 22.0 20.0 2.0 –3.0 24.7 21.0 3.0 –2.0 27.7 22.0 4.0 –1.0 31.0 23.0 5.0 0.0 34.8 24.0 6.0 This specification is valid for Mic 1–8 inputs if Microphone Level setting is selected. This specification is valid for Line 1–8 inputs if Line Level setting is selected.

Physical interface guide D14644.03 Codec C90 Physical Interface Guide TC4.1, February 2011. © 2010-2011 Cisco Systems, Inc. All rights reserved. www.cisco.com Audio hardware information table Notes: 1. Default levels are marked with white text on black 2. For the dBu value for input clipping level and absolute max output level, a sine waveform is assumed 3. If numbers in dBV are required, dBV value is 2.2 dB lower than the dBu value. Example: -10 dBu equals -12.2 dBV Volume control Ring tone volume* Audio gain value 0 0 1 -34.5 dB 70 0.0 dB 100 15.0 dB Audio signal levels, cont... Volume control table Hardware Information Mic 1–8 * Line in 1–8 ** Line out 5–6 Line in 1–4 Line out 1–4 Signal type Balanced Balanced Balanced Unbalanced Unbalanced Connector (codec) XLR-F XLR-F XLR-M Female RCA/phono Female RCA/phono Input impedance 8100 Ohm (pin 2–3) 10k Ohm (pin 2–3) 10 k Ohm Output impedance 50 Ohm 100 Ohm Max input level when set to Min input level –18dBu/275mVpp 24dBu/34.7Vpp 18dBu/17.4Vpp Max input level when set to Max input level –42dBu/35mVpp 0dBu/4.4Vpp -6dBu/2.2Vpp Max output level when set to Min output level 0dBu/4.4Vpp -6dBu/2.2Vpp Max output level when set to Max output level 24dBu/34.8Vpp 18dBu/17.4Vpp Gain range <–24dB (24 steps of 1dB) –> Phantom power 48 Volt +/- 2% Phantom power resistor pin 1 6800 Ohm Phantom power resistor pin 2 6800 Ohm Max phantom power current (per mic) 14mA Line outputs 1 to 4 Female RCA/phone Signal levels Absolute max output level Nominal level Level setting [dB] [Vpp] [dBu] [dBu] -24.0 1,1 -6.0 -24.0 -23.0 1,2 -5.0 -23.0 -22.0 1,4 -4.0 -22.0 -21.0 1,5 -3.0 -21.0 -20.0 1,7 -2.0 -20.0 -19.0 1,9 -1.0 -19.0 -18.0 2,2 0.0 -18.0 -17.0 2.5 1.0 -17.0 -16.0 2.8 2.0 -16.0 -15.0 3.1 3.0 -15.0 -14.0 3.5 4.0 -14.0 -13.0 3.9 5.0 -13.0 -12.0 4.4 6.0 -12.0 -11.0 4.9 7.0 -11.0 -10.0 5.5 8.0 -10.0 -9.0 6.2 9.0 -9.0 -8.0 6.9 10.0 -8.0 -7.0 7.8 11.0 -7.0 -6.0 8.7 12.0 -6.0 -5.0 9.8 13.0 -5.0 -4.0 11.0 14.0 -4.0 -3.0 12.3 15.0 -3.0 -2.0 13.8 16.0 -2.0 -1.0 15.5 17.0 -1.0 0.0 17.4 18.0 0.0 * This specification is valid for Mic 1–8 inputs if Microphone Level setting is selected ** This specification is valid for Line 1-8 inputs if Line Level setting is selected * The ring tone volume, which is displayed on screen when using the TRC5 remote control, goes from 0 to 20.

Physical interface guide D14644.03 Codec C90 Physical Interface Guide TC4.1, February 2011. © 2010-2011 Cisco Systems, Inc. All rights reserved. www.cisco.com Network connectors Ethernet interface 2 × Gigabit Ethernet LAN (RJ-45 Jack) interface (GbE). Ethernet 1: Main connector for network connection Ethernet 2: For direct pairing with the Cisco TelePresence Touch for C Series. Ethernet 2 1 ---------- 1 2 ---------- 2 3 ---------- 3 6 ---------- 6 Wiring diagram standard cable RJ-45 Connector pin-out TOP FRONT 1 8 1 8 Ethernet 1

Physical interface guide D14644.03 Codec C90 Physical Interface Guide TC4.1, February 2011. © 2010-2011 Cisco Systems, Inc. All rights reserved. www.cisco.com COM port and Camera Control port COM port 1 x COM (RS-232) data port for codec control and configuration through API commands. Camera Control port 1 x Camera Control (RS-232) port for power and camera control (pan, tilt, zoom) using the VISCA™* protocol. Main connector. The main camera is connected to the Camera Control port. Power. Pin No. 4 on the Camera Control port provides 12 V DC / 1 A to the main camera. If more than one camera is connected, only the first camera is powered from the codec. The additional cameras must be daisy chained by using a serial cable, and each will need an external power supply. Additional cameras. For information about additional cameras, see the PrecisionHD Camera User Guide which is found on our web site, go to: http://www.cisco.com/go/ telepresence/docs *VISCA™ is a trademark of Sony Corporation Pin-out—Camera cable Signal name RJ-45 pin D-SUB pin +12V DC 1 Twisted pair 4 GND 2 5 RX 3 Twisted pair 2 TX 6 3 NC 4 Twisted pair 1 NC 5 6 GND 7 Twisted pair 5 +12V DC 8 4 Pin-out—COM Port Pin Signal name Direction 1 Carrier detect, CD From DCE 2 Receive data, RXD From DCE 3 Transmit data, TXD To DCE 4 12 V / 1 A To the main camera 5 Signal GND 6 Data set ready, DSR From DCE 7 Ready to send, RTS To DCE 8 Clear to send, CTS From DCE 9 Ring indicator, RI From DCE Pin-out—VISCA™ camera control RJ11, 8 pins shielded modular jack Pin Signal name 8 +12V (presence 2.8mA current source when connected in daisy chain) 7 GND 6 TXD (out) 5 NC (no connect) 4 NC (no connect) 3 RXD (in) 2 GND 1 +12V RS232 9 pin D-SUB pin-out External view of socket Camera Control Port COM port 1 5 6 9

Physical interface guide D14644.03 Codec C90 Physical Interface Guide TC4.1, February 2011. © 2010-2011 Cisco Systems, Inc. All rights reserved. www.cisco.com Power Power socket Power Cord Socket. Accepts 100-240V, 50/60Hz, 2.8A max. CAUTION! This equipment must be grounded. Power switch Power Switch (On/Off) Chassis grounding For grounding of the chassis Chassis Grounding Power Socket Power Switch

Physical interface guide D14644.03 Codec C90 Physical Interface Guide TC4.1, February 2011. © 2010-2011 Cisco Systems, Inc. All rights reserved. www.cisco.com GPIO and other connectors GPIO 1 × GPIO (General Purpose Input/Output) 6 pins Phoenix plug, having 4 ports for On/Off control, GND and +12V. You can configure input/output integrations by using pre– defined behavior. Exposure of states and commands for external control requires external programming. For information about the API commands, see the API Guide for the codec, go to: http://www.cisco.com/go/telepresence/ docs Usage information • A contact closure between the GND and a GPIO port pin is detected as a low input signal. • When used for voltage inputs, the GPIO port detects it as: • Low signal for voltages 0 - 1 VDC • High signal for voltages 2 - 12 VDC • When used for outputs, the GPIO port acts as a switch to GND, and is rated for 500mA @ 48V DC. The +12V pin provides +12 VDC, and is capable of sourcing up to 500mA. • The GND connector is a common ground for all pins in the GPIO port. USB 1 × USB Host 1 × USB Device For future use. T Link 2 × T Link, RJ45 connector. The cable for T Link out must be shielded. For future use. T Link (for future use) USB (for future use) GPIO GPIO pin-out +12V 4 3 2 1 GND +12V 4 3 2 1 GND

Physical interface guide D14644.03 Codec C90 Physical Interface Guide TC4.1, February 2011. © 2010-2011 Cisco Systems, Inc. All rights reserved. www.cisco.com On our web site you will find an overview of the worldwide Cisco contacts. Go to: http://www.cisco.com/web/siteassets/contacts Corporate Headquarters Cisco Systems, Inc. 170 West Tasman Dr. San Jose, CA 95134 USA Disclaimer THE SPECIFICATIONS AND INFORMATION REGARDING THE PRODUCTS IN THIS MANUAL ARE SUBJECT TO CHANGE WITHOUT NOTICE. ALL STATEMENTS, INFORMATION, AND RECOMMENDATIONS IN THIS MANUAL ARE BELIEVED TO BE ACCURATE BUT ARE PRESENTED WITHOUT WARRANTY OF ANY KIND, EXPRESS OR IMPLIED. USERS MUST TAKE FULL RESPONSIBILITY FOR THEIR APPLICATION OF ANY PRODUCTS. THE SOFTWARE LICENSE AND LIMITED WARRANTY FOR THE ACCOMPANYING PRODUCT ARE SET FORTH IN THE INFORMATION PACKET THAT SHIPPED WITH THE PRODUCT AND ARE INCORPORATED HEREIN BY THIS REFERENCE. IF YOU ARE UNABLE TO LOCATE THE SOFTWARE LICENSE OR LIMITED WARRANTY, CONTACT YOUR CISCO REPRESENTATIVE FOR A COPY. The Cisco implementation of TCP header compression is an adaptation of a program developed by the University of California, Berkeley (UCB) as part of UCB’s public domain version of the UNIX operating system. All rights reserved. Copyright © 1981, Regents of the University of California. NOTWITHSTANDING ANY OTHER WARRANTY HEREIN, ALL DOCUMENT FILES AND SOFTWARE OF THESE SUPPLIERS ARE PROVIDED “AS IS” WITH ALL FAULTS. CISCO AND THE ABOVE- NAMED SUPPLIERS DISCLAIM ALL WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING, WITHOUT LIMITATION, THOSE OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT OR ARISING FROM A COURSE OF DEALING, USAGE, OR TRADE PRACTICE. IN NO EVENT SHALL CISCO OR ITS SUPPLIERS BE LIABLE FOR ANY INDIRECT, SPECIAL, CONSEQUENTIAL, OR INCIDENTAL DAMAGES, INCLUDING, WITHOUT LIMITATION, LOST PROFITS OR LOSS OR DAMAGE TO DATA ARISING OUT OF THE USE OR INABILITY TO USE THIS MANUAL, EVEN IF CISCO OR ITS SUPPLIERS HAVE BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. Cisco and the Cisco Logo are trademarks of Cisco Systems, Inc. and/or its affiliates in the U.S. and other countries. A listing of Cisco's trademarks can be found at www.cisco.com/go/trademarks. Third party trademarks mentioned are the property of their respective owners. The use of the word partner does not imply a partnership relationship between Cisco and any other company. (1005R) Any Internet Protocol (IP) addresses and phone numbers used in this document are not intended to be actual addresses and phone numbers. Any examples, command display output, network topology diagrams, and other figures included in the document are shown for illustrative purposes only. Any use of actual IP addresses or phone numbers in illustrative content is unintentional and coincidental. TANDBERG is now a part of Cisco. TANDBERG® is a registered trademark belonging to Tandberg ASA.