Megalarm MEGA 450 Installation & Operation Instructions

INSTALLATION & OPERATION INSTRUCTIONS WIRING DIAGRAM H1: Main 5 Pin White harness H3: 6 Pin White Mini Connector Black Antenna Wire LED Indicator Valet Switch H7/3 Blue Wire: (-) 200mA Unlock H7/1 Green Wire: (-) 200mA Lock Pulse H7 3 Pin White H2 4 Pin Orange H5 2 Pin Blue H6 2 Pin White H4 Black Wire Dual Zone Shock Sensor H1 5 Pin White H3 6 Pin White H1: MAIN 5 PIN WIRE HARNESS: 5. Red Wire: +12V To Constant Battery Source 4. Brown Wire: Positive output To 3. Black Wire: Ground to Vehicle FRAME 2. White Wire: Parking Light Relay Output 15A Fuse 1. Red / White Wire: Parking Light Relay input Siren Or Horn (Programmable) H3: 6 PIN MINI CONNECTOR WIRE HARNESS: 6. Gray Wire: (-) 200ma Programmable Output 2. Blue Wire: Zone 2 / Instant Trigger Ground Input 1. Violet Wire: Zone 3 / Positive Door Pin Switch Input 4. Yellow Wire: Zone 5 / To Ignition Switched + 12V 5. Orange Wire: 200mA Grounded when armed 3. Green Wire: Zone 3 / Negative Door Pin Switch Input 85 86 30 87a 87 Cut To start solenoid From ignition switch Red wire White wire Orange wire Channel 2 / 2 Step Door Unlock / Pager Output. 12V 12V 1

through holes on the firewall to prevent fraying. Watches out sharp edges that may damage wires and causes short circuit. CAUTION: Do not connect the wire harness to the control module until all wiring to vehicle is complete. H1: MAIN 5 PIN WIRE HARNESS: H1/1. RED / WHITE WIRE – PARKING LIGHT RELAY INPUT -- The RED/WHITE wire is the input to the flashing parking light relay. The connection of the RED/WHITE wire will determine the output polarity of the flashing parking light relay. If the vehicle you are working on has +12volt switched parking lights, you don’t need connect this wire. This wire already connected to +12volt. If the vehicle’s parking lights are ground switched, cut the RED/WHITE wire, connect the RED/WHITE to chassis ground. H1/2. WHITE WIRE -- PARKING LIGHT RELAY OUTPUT (+12 V 10A OUTPUT) -- Connect the WHITE wire to the parking light wire coming from the headlight switch. Do not connect the white wire to the dashboard lighting dimmer switch. (Damage to the dimmer will result). The limitation of the white wire is 10 AMP max. Do not exceed this limit or damage to the alarm and parking relay will result. H1/3. BLACK WIRE -- SYSTEM GROUND – This is main ground connection of the alarm module. Make this connection to a solid section of the vehicle frame. Do not connect this wire to any existing ground wires supplied by the factory wire loom, make the connection to the vehicle's frame directly. H1/4. BROWN WIRE -- SIREN DRIVE OR HORN OUTPUT -- (Set Feature III – 1 Programming) SIREN DRIVE OUTPUT (Factory default setting) This is the positive (+) output connection for the siren. Current capacity is 2 amps. Make connection to the (+) red wire from the siren. Make the (-) black wire coming from the siren to a good chassis ground. (+) LOW CURRENT HORN OUTPUT -- (Set Alarm Feature III – 1 To Horn Output) This wire is provided to use the existing vehicle's horn as the alarm system's optional's warning audible device. It's a transistorized low current output, and should only be connected to the low current positive (+) output from the vehicle's horn switch. H1/5. RED WIRE -- SYSTEM POWER (+12V CONSTANT) -- The RED wire supplies power to the system. Connect this wire to a constant +12 volt source. H2: 4 PIN ORANGE CONNECTOR FOR 2 STAGE SHOCK SENSOR 4. Green Wire / Warn Away Input 3. Blue Wire / Zone 4 Ground Trigger 2. Black Wire / Negative 1. Red Wire / +12Volts Function: Allows easy positive, negative, instant trigger, and warn-away trigger connection with quick disconnect ability for other detection devices. H3: 6-PIN MINI CONNECTOR WIRE HARNESS. H3/1. VIOLET WIRE -- POSITIVE DOOR SWITCH SENSING INPUT-- This wire is the positive trigger input wire for positive door pin switch. This wire is connection for "positive" type factory door pins(typical FORD MOTOR). Locate the "common wire" for all door pins and make the connection of the Violet Wire here. H3/2. BLUE WIRE -- GROUND INSTANT TRIGGER INPUT -- This wire is the ground trigger input wire for hood/trunk pin switches. H3/3. GREEN WIRE -- NEGATIVE DOOR SWITCH SENSING INPUT -- This wire is the ground trigger input wire for negative door pin switch. This wire is connection for "grounding" type factory door pins locate the "common wire" that connects the door pin switches. Make the connection of the Green Wire here. H3/4. YELLOW WIRE – TO IGNITION SWITCHED +12V -- This wire is connected to a switched 12 volts source. This wire should receive "12 Volts" when the ignition key is in the "ON" and "START" position. When the ignition is turned "OFF", this wire should receive "0" voltage. H3/5. ORANGE WIRE – (-) 200mA GROUNDED OUTPUT WHEN ARMED -- This wire will become grounded when the alarm is armed. The current capacity of this wire is 200mA. This output can control starter disable, when an intrusion is detected and the system is triggered. The vehicles prevent from any unauthorized starting. 2

b). When found, use voltmeter, connect one probe of the voltmeter to ground and connect the other end of the probe to the starter wire, it should receive "12 Volts" only when the ignition key in the "START" position. c). After locating the correct wire, cut it in half, try to start the vehicle. The engine should not "crank over". d). When the extend wires are needed, they must be exactly same gauge as the cut wire. Connect the cut wire from the key switch to the RED wire (pin #30) of the relay, and connect the starter wire to the WHITE wire (pin #87a ) of the relay. e). Connect the H3/5 ORANGE Wire from the control module to the ORANGE wire (pin #86) of the relay. NOTE: If more than one electronic device will be connected to the H3/5 ORANGE Wire, it will be necessary to isolate the connection of each device control wires with a 1N4003 diode. 87 87a 85 30 86 IN4003 Diode H3/5 Orange wire “Start” “On” White wire X Cut Red wire Orange wire “Acc” “Off” Starter H3/6 . GRAY WIRE – (-) 200mA PROGRAMMABLE OUTPUT – CHANNEL 2 OUTPUT (Factory default setting) This will become a 1 second pulse ground by press and hold the button II on transmitter for two seconds, the current capacity of this wire is 200 mA. this feature allows you to remote control trunk release or other electric device. 2 STEPS UNLOCK OUTPUT (Set Feature III – 2 Programming to “2 Step Door Unlock Output) The 2 steps unlock feature will work for the most fully electronic door lock circuit. The vehicle must have an electronic door lock switch (not the lock knob or key switch), which locks and unlocks all of vehicle's doors. When wired for this feature, press the button II one time will disarm the alarm and unlock the driver's door only. If, press button II two times within 3 seconds, the alarm will disarm and all doors will unlock. PAGER OUTPUT (Set Feature III – 2 Programming to “PAGER Output) This wire provides a negative output, when the alarm triggered. The current capacity of this wire is 200mA. For optional electrical device in this system, please connected to an additional relay. (I.E. Pager interface....) H4: RF ANTENNA - BLACK THIN WIRE The black thin wire on control module is the receiver antenna wire. Antenna placement is very important! Ensure that it is unwrapped and stretched out with the last 6" straight and keep it away from large metal objects or chassis for best reception. H7: 3 PIN DOOR LOCK CONNECTOR: Blue Wire Green Wire ( - ) 200mA Lock Pulse ( - ) 200mA Unlock Pulse 3 Pin Mini-Molex Connector INSTALL NEW DOOR LOCK MOTOR Blue Wire Green +12V 30 86 87a 85 87 30 86 87a 85 87 3 Pin Plug To Alarm NEGATIVE TRIGGER DOOR LOCK SYSTEM Blue Wire Door Unlock Green Wire Door Lock Locking Master Switch To Exiting Door Lock Relay POSITIVE TRIGGER DOOR LOCK SYSTEM Locking Master Switch To Exiting Door Lock Relay + 12V Blue Wire Green +12V 30 86 87a 85 87 30 86 87a 85 87 3 Pin Plug To Alarm 3

Lock Wire To Door Lock Motor To Slave Door Lock switches Cut the Existing Unlock Wire 3 Pin Plug To Alarm 5-WIRE ALTERNATING DOOR LOCK 30 86 87a 85 87 30 86 87a 85 87 +12V Green Wire Blue Wire VACUUM OPERATED CENTROL LOCKING Green Wire Blue Wire +12V X Cut Compressor Door Switch 30 86 87a 85 87 30 86 87a 85 87 3 Pin Plug To Alarm 2 STEP DOOR UNLOCK WIRE CONNECTION FOR 5 WIRE ALTERNATING DOOR LOCKS +12V Cut the Existing Lock Wire Cut Existing Unlock X Cut the Unlock Wire Lock Unlock OEM Door Master Lock OEM Slave Door Lock Switch +12V Lock Unlock To All Other Door Lock Motors 6-Pin Plug From Alarm H3/6 Gray Wire x X H7/1 Blue Wire OEM Driver’s Door Lock Motor + 12V + 12V 85 86 87 87A 30 30 87 85 87A 86 30 87 85 87A 86 H7/3 Green Wire 3 Pin Plug To Alarm VACUUM OPERATED DOOR LOCKING SYSTEM: TYPICAL OF MERCEDES BENZ AND AUDI. Locate the wire under the driver's kick panel. Use the voltmeter connecting to ground, verify that you have th correct wire with the doors unlocked, the voltmeter will receive "12 volts". Lock the doors and the voltmeter wi read "0 volt". Move the alligator clip to +12V and the voltmeter will receive "12 volts". Cut this wire and make connections. Be sure to program door lock timer to 3 seconds.(See Feuture II – 1 Programming.) 2 STEP DOOR UNLOCK WIRE CONNECTION FOR GROUND SWITCHED DOOR LOCKS Cut Existing Unlock X Lock Unlock OEM Door Master Lock Switch To All Other Door Lock Motors 6-Pin Plug From Alarm H3/6 Gray Wire OEM Door Lock Motor Existing Neg. Lock Wire Existing Neg. Unlock Wire 86 30 85 87 87A + 12V H7/3 Green Wire Door Lock H7/1 Blue Wire Door Unlock 3 Pin Plug To Alarm OEM Door Lock Relay 2 STEP DOOR UNLOCK WIRE CONNECTION FOR POSITIVE SWITCHED DOOR LOCKS Cut Existing Unlock X Lock Unlock OEM Door Master Lock Switch To All Other Door Lock Motors 6-Pin Plug From Alarm H3/6 Gray Wire OEM Driver's Door Lock Motor + 12V Existing Pos. Lock Wire Existing Pos. Unlock Wire 30 87A 87 86 85 +12V + 12V OEM Door Lock Relay 86 30 85 87 87A H7/1 Blue Wire Door Unlock H7/3 Green Wire Door Lock + 12V 86 30 85 87 87A 4

Enter: 1. Turn the Ignition switch ‘OFF/ON’ 3 TIMES and stay in ON position. Within 15 seconds. 2. Push the Valet switch 3 times and hold it until a long chirp is hearing then release the valet switch. You are now in the Transmitter programming mode. Program: 1. Press button on one of the transmitter until the siren respond with a confirming chirp the first transmitter is now programmed. 2. Press button on the second transmitter until the siren respond with a confirming chirp, the second transmitter is now programmed. 3. Apply the same procedure to program 3rd and 4th. Exit: Turn Ignition to 'OFF' position, or leave it for 15 seconds. A 3 long chirps to confirm exit. Note: If more than 4 transmitters programmed, the system only kept the last 4 transmitters. B. ALARM FEATURES PROGRAMMING: ALARM FEATURE “I” PRORAMMING: 1. Turn the Ignition 'switch ‘ON/OFF’ 3 TIMES and stay in OFF position. 2. Push the Valet switch 2 times and hold it until one chirp and a long chirp is hearing then release the valet switch. You are now in the Alarm feature ‘I’ programming mode. 3. Press and release the transmitter button ‘A’ corresponding to the feature ‘A’ you want to program. a. The siren chirps and LED pause will indicate the latest setting. b. The factory default setting is always [1] LED flash, [1] chirp. 4 Depress the transmitter button ‘A’ to change the feature. Simple re-depressing the transmitter button ‘A’ again until the module advances to your desired setting. a. In this case, Press button ‘A’ again, the module would advance to [2] LED flash, [2] chirp. Press button ‘A’ again, the module would advance to [3] LED flash, [3] chirps etc. 5. Depress the transmitter button ‘B’ corresponding to the feature ‘B’ you wants to program. Press Transmitter Button One Chirp / LED one pulse Factory Default Setting Two Chirps / LED two pulse 1. Button I Chirps on Chirps off 2. Button II Automatic Rearm On Automatic Rearm Off 3. Button I + II With Door Ajar error chirp. Bypass Door Ajar error chirp Exit: Turn Ignition to 'ON' position, or leave it for 15 seconds. A 3 long chirps to confirm exit. ALARM FEATURE “II” PRORAMMING: 1 Turn the Ignition 'switch ‘ON/OFF’ 3 TIMES and stay in OFF position. 2 Push the Valet switch 4 times and hold it until two chirps and a long chirp is hearing then release the valet switch. You are now in the Alarm feature ‘II’ programming mode. 3 Press and release the transmitter button ‘A’ corresponding to the feature ‘A’ you want to program. Press Transmitter Button One Chirp / LED one pulse Factory Default Setting Two Chirps / LED two pulse Three Chirps / LED three pulse 1 Button I 0.9-second Door lock pulses. 3.0-second Door lock pulse. Double pulse unlock 2 Button II Active arming Passive arming without passive door locking Passive arming with passive door locking. 3 Button I + II Ignition controlled door locks & unlocks Without ignition controlled door locks & unlocks Exit: Turn Ignition to 'ON' position, or leave it for 15 seconds. A 3 long chirps to confirm exit. ALARM FEATURE “III” PRORAMMING: 1 Turn the Ignition switch ‘ON/OFF’ 3 TIMES and stay in OFF position. 2 Push the Valet switch 6 times and hold it until three chirps and a long chirp is hearing then release the valet switch. You are now in the Alarm feature ‘III’ programming mode. 5

Press Transmitter Button One Chirp / LED one pulse Factory Default Setting Two Chirps / LED two pulse Three Chirps / LED three pulse 1 Button I H1/4 Brown Wire = Siren Output H1/4 Brown Wire = Horn Output 2 Button II H3/6 Gray Wire = Trunk (Channel 2) Output H3/6 Gray Wire = Two Step Door Unlock Output H3/6 Gray Wire = Pager Output 3 Button I + II Car Jacking Off Car Jacking On Exit: Turn Ignition to 'ON' position, or leave it for 15 seconds. A 3 long chirps to confirm exit. OPERATION MANUAL A. TRANSMITTER OPERATION: Transmitter Button System Function Remark Button I Arm / Lock door Button I – I Arm and Delete Optional Sensor Press twice. Button I Car Locator System in Armed Button I for 3 seconds Panic function Press 3 seconds Button II Disarm & Unlock Door Button II – II Two Steps Door Unlock & Disarm System Press twice within 3 seconds. Button II for 2 seconds Disarm & Pop Trunk Release Press 2 seconds Button I + II Silent Arm / Disarm Ignition in "off" position. Button I + II for 2 seconds Activate Anti Car-Jacking Ignition in "on" position. B. LED INDICATOR: LED Function LED Function Off Disarmed 2 flashes... pause Trigger on trunk/hood Slow flash Armed 3 flashes... pause Trigger on door switch Fast flash Passive arming 4 flashes... pause Trigger on Dual Zone Shock Sensor On (solid) Valet mode 5 flashes... pause Trigger on Ignition switch C. CHIRP INDICATORS: D. PARKING LIGHT: Chirp Function Parking light Function 1 chirp Arm 1 flash Arm 2 chirps Disarm 2 flashes Disarm 3 chirps Defective reminder 3 flashes Disarm / Intrusion 4 chirps Disarm / Intrusion 12 flashes Car Locator 6 chirps Car Locator E. ALARM OPERATING CONDITION: Siren Parking Light LED Doors Starter disable Pager 1. Arming 1 Chirp 1 Flash Slow flash Locking On 2. Disarming 2 or 4 Chirps 2 or 3 Flashes Off or Fast flash Unlocking Off 3. Trigger Alarming Flashes Slow flash On On 4. Panic Alarming Flashes Slow flash Locking On F. ACTIVE ARMING – LOCK & ARM: 1. Press button I on transmitter. 2. The siren will chirp once and parking light will flash once indicating that the system is now armed. The vehicle’s door will lock upon arming when interfaced with the security system. Note: Defective sensor reminder: If the siren sounds 3 chirps, then you have left a door, trunk, or hood lid ajar. (See Feature “I - 3 Programming) SILENT ARMING / DISARMING: Press the button I + II together on the transmitter will arm or disarm your security system, No chirp sound will be heard, arm / disarm confirmation will be through the vehicles parking lights only. 6

seconds will arm the security system, by-pass the shock sensor and the optional sensor connected to 4 pin plug. The system will chirp one additional time to confirm the sensor bypass mode was activated. The sensor bypass feature is programmed to activate for one arming cycle only. The security system will return to normal operation during the next arming cycle. G. PASSIVE ARMING: (See Feature “II - 2” Programming) Active arming / disarming is controlling your security system via the remote transmitter. This security system is equipped with an optional Passive Arming feature, which allows the security system to arm 30 seconds after the last door is closed. Operation is as follows. 1. Turn the ignition to the “OFF” position and exit the vehicle. 2. After all entrances are closed, the security system LED will flash fast for 30 seconds. If you reopen any door / hood / trunk, the security system LED will stop flashing. It will begin flashing again once the vehicle all entrances are closed. 3. After 30-second timer has elapsed, the security system will automatically “ARM”. The siren will chirp [1] time and the parking lights will flash [1] time. PASSIVE DOOR LOCKING: (See Feature “II - 2” Programming) The vehicle’s door will automatically lock after passive arming cycle has been completed. H. ACTIVE DISARMING – UNLOCK & DISARM: 1. Press the button II on the transmitter. 2. The siren will chirp twice and parking light will flash twice to indicating that the security system is now disarmed. The vehicle’s door will unlock disarming when interfaced with the security system. TAMPER DISARMING: If alarm triggered, upon disarm the system, siren chirp 4 times, parking light flash 3 times. TWO STEP DOOR UNLOCK: (See Feature III – 2 Programming.) This feature will independently unlock the driver’s door only when disarming the security system. Pushing the button II on the transmitter two times within 3 seconds will unlock the entire vehicle. AUTOMATIC RE-ARM (See Feature “I - 2” Programming): If this feature is selected, the security system will automatically re-arm itself 60 seconds after disarming with remote transmitter. Automatic rearm will cancel if any door is opened before the 60 seconds timer has elapsed. I. DISARMING WITHOUT A TRANSMITTER The Override function may be used if the remote transmitter is lost or inoperative. 1. Enter the vehicle and turn the ignition switch to 'ON’ position. (Alarm will sound.) 2. Within 10 seconds push and release the valet switch The alarm will stop sounding and enter the disarm mode. You can now start and operate the vehicle normally. J. VALET MODE: The valet switch allows you to temporarily bypass all alarm function, eliminating the need to hand your transmitter to parking attendants or garage mechanics. When the system is in valet mode, all alarm function are bypassed, however the remote panic feature and remote door lock will remain operational. Enter Valet Mode: 1. Turn the ignition to “ON” position. 2. Push and hold valet switch for 2 seconds until the LED turns on. The LED will remain on as long as the system is in 'valet mode. Exit Valet Mode: 1. Return to normal operation, turn ignition 'ON'. 2. Push and hold valet switch for 2 seconds, The LED will turn off indicate the system are exiting the valet mode. K. PANIC FUNCTION: The transmitter can be used as a remote panic switch to manually trigger the alarm in case emergency. 1. Press and hold the button I on the transmitter for 3 seconds. The alarm will immediately sound. 2. To stop the alarm, press and hold the button I or II on the transmitter, the panic mode will be turned off immediately. 3. If the button is not pressed, the alarm will automatically stop after 30 seconds. L. TRIGGER THE SYSTEM When armed, your vehicle is protected as follows: 1. Light impact will trigger the warn-away signal. A long chirp from siren/horn. 2. Heavy impact / Doors open / Hood open / Trunk open / Turns on the ignition switch will trigger the programmed sequence. The starter disable relay (if installed) prevents the vehicle’s starter from cranking. The siren and parking lights will turn on to alerting of an intrusion for 30 seconds. Then it will stop and automatic reset and re-arm. 7

seconds . M. ANTI CAR-JACKING Warning: If you don't need the anti car-jacking function in this alarm system, be sure to set anti car-jacking feature “OFF”. This system is default setting all anti car-jacking “OFF”. (See Alarm Feature III - 3 Programming.) 1. TRANSMITTER ACTIVATE THE ANTI CAR-JACKING: Press and hold button I + II on the transmitter for 2 seconds while the vehicle’s ignition is ON. The parking light will turn on for 1.5 seconds to indicate trigger the anti car-jacking. 2. DOOR SWITCH ACTIVATE ANTI CAR-JACKING: It operate as below: 1. Turn the ignition switch to “ON” position, the system is armed. 2. Once the system is armed, If you are forced from the vehicle, the system will active the anti Car-jacking trigger when the door is opened and closed. TRIGGER THE ANTI CAR-JACKING MODE: 3-timer circuits will function as follows: First timer: a. 50 seconds after the system has been triggered. The siren will start chirping for 15 seconds. b. During this 15 seconds period of chirping, you will be alerting to push the valet switch once to turn off the anti car-jacking feature. c. If not, it will enter second timer anti car-jacking. Second timer: 65 seconds after the system has been triggered. The siren starts alarming and the parking light starts flashing. Third timer: 90 seconds after the system has been triggered a. The siren still alarming and the parking light flashing, and b. The starter disable will activate to prevent the vehicle from starting. c. It will remain active until the vehicle's battery power exhausted. OVERRIDE THE SYSTEM TO TURN OFF ANTI CAR-JACKING: Turn the ignition switch from OFF to ON, and within 10 seconds push valet switch, the siren will stop and the system disarmed N. IGNITION CONTROL DOOR LOCKS. (See Feature II – 3 Programming.). If the vehicle’s door lock have been interfaced to the security system, the system will automatically lock the vehicle's door when the ignition is turned “ON” and /or unlock the vehicle’s door when the ignition is turned “OFF”. O. TRUNK RELEASE. (See Feature III – 2 Programming.). Press and hold button II on transmitter for two seconds to remote control the trunk release or other electric devices. P. CAR LOCATOR Under Arm situation press the button I on the transmitter to active car locator function. The siren will chirp 6 times. The parking light will flash 12 times, for you to easily locate your car. 8