Baumatic BT26.1 Instruction Manual

BT26.1SS/BT29.1SS Cooker Hood 60/90cm Cooker Hood in Stainless Steel NOTE: This User Instruction Manual contains important information, including safety & installation points, which will enable you to get the most out of your appliance. Please keep it in a safe place so that it is easily available for future reference; for you or any person not familiar with the operation of the appliance. DD 20/06/07 2

5 – 7 Specifications of your cooker hood 8 Using your Baumatic cooker hood 9 Start and increase speed 9 Motor stopping and decreasing speed 9 Timer function 9 Light on/off function 9 Special functions 10 Cleaning your Baumatic cooker hood 11 The grease filter 11 Maintenance 12 Removing and cleaning the grease filter 12 Changing a light bulb 13 Fitting the carbon filters 14 Installation 15 Electrical connection 15 – 16 Before beginning installation 16 – 17 Installing your cooker hood 17 – 19 Connecting to external ducting 20 Fitting the chimney section 20 – 22 Extraction mode or recirculation mode? 23 Troubleshooting 24 Baumatic Ltd. conditions of guarantee 25 Contact details 26

disconnect it from the power supply. Cut off and render any plug useless. Cut the cable off directly behind the appliance to prevent misuse. This should be undertaken by a competent person. CONFORMITY TO W.E.E.E. DIRECTIVE 4

Your safety is of the utmost importance to Baumatic. Please make sure that you read this instruction booklet before attempting to install or use the appliance. If you are unsure of any of information contained in this booklet, please contact the Baumatic Technical Department. IMPORTANT: Any installation work must be carried out by a qualified electrician or competent person. o The hood must be installed in accordance with the installation instructions and all measurements followed. o If the cooker hood is installed for use above a gas appliance then the provision for ventilation must be in accordance with the Gas Safety Codes of Practice BS.6172, BS.5440 & BS.6891 (Natural Gas) and BS.5482 (LP Gas) 1994, the Gas Safety (Installation & Use) Regulations, the Building Regulations issued by the Department of the Environment, the Building Standards (Scotland) (Consolidated) Regulations issued by the Scottish Development Department. o It is dangerous to alter the specifications or to modify this product in any way. Do not tamper with it or attempt to modify the appliance in any way. o When installing the hood, ensure that the following recommended distances are observed between the highest point on the hob top (including the burners) and the bottom of the cooker hood: ¾ Electric cookers: 700 mm ¾ Gas cookers: 700 mm ¾ Coal/ oil cookers: 800 mm IMPORTANT: DO NOT SET YOUR COOKER HOOD LESS THAN 700mm ABOVE YOUR COOKER. o When installed between adjoining wall cabinets, the cabinets must not overhang the hob. 5

you handle your appliance, especially during installation and cleaning. DO NOT CLEAN IN BEHIND THE GREASE FILTERS! o If the room where the cooker hood is to be used contains a fuel burning appliance such as a central heating boiler then its flue must be of the sealed or balanced flue type. o If other types of flue or appliances are fitted, ensure that there is an adequate supply of air in the room. o When the hood is being used in its extractor function, ensure that the ducting is fire retardant and that there are no bends sharper than 90 degrees as this will reduce the efficiency of the hood. o Ensure the ducting for the extractor function has the same diameter as the outlet hole all the way through. o Keep young children from using, playing with or tampering with the cooker hood. Older children and infirm persons should be supervised if they are using the cooker hood. o Your cooker hood is for domestic use only. o Please dispose of the packing material carefully – children are especially vulnerable to it. o Dirty oil is an even greater fire risk. o Always put lids on pots and pans when cooking on a gas cooker. o The manufacturer refuses to accept any responsibility for damages arising to the hood or it catching on fire from failure to observe fire safety advice in these instructions. 6

removing air from your room. Ensure that proper ventilation measures are being observed. Note that it removes odours from your room, not steam. o Warning - Always ensure that the cooker hood has been disconnected from the power supply before carrying out any work on the hood, including replacing light bulbs. o Do not connect the ducting system of this appliance to any existing ventilation system which is being used for any other purpose. o Do not install above a cooker with a high level grill. o Never leave frying pans unattended during use as overheated fats and oils might catch fire. o Do not leave naked flames under the cooker hood. o Do not attempt to use the cooker hood if it is damaged in any way. Never attempt to use it without the grease filters fitted or if the filters are excessively greasy! o Never flambé cook under this cooker hood. THE MANUFACTURER DECLINES ALL RESPONSIBILITY IN THE EVENT OF FAILURE TO OBSERVE THE INSTRUCTIONS GIVEN HERE, FOR INSTALLATION, MAINTENANCE AND SUITABLE USE OF THE HOOD. 7

Congratulations on purchasing a Baumatic Cooker Hood! DIMENSIONS: BT26.1SS Width (canopy): 600 mm Depth (canopy): 470 mm Height (with chimney) 776 mm – 1116 mm DIMENSIONS: BT29.1SS Width (canopy): 900 mm Depth (canopy): 470 mm Height (with chimney) 776 mm – 1116 mm DIMENSIONS OF CHIMNEY SECTION: 222 mm x 197 mm Your stainless steel Cooker Hood is fitted with: o High extraction tangential motor o Touch control operation o 5 Speeds and booster o 2 Metallic grease filters o 3 Metallic grease filters (BT29.1SS only) o 2 Halogen lights Extraction capacity: 750 m³/hr Noise level min/max: 49 – 63 dB Optional Extra: 2 x UCF1 Carbon filters for air recirculation mode (available from the Baumatic Spares Department).

IMPORTANT: THE ELECTRONIC CONTROLS ON YOUR OOKER HOOD HAVE MULTIPLE FUNCTIONS. tart and Increase Speed (6 speeds) The hood utomatically sets itself to speed Level 1 when activated. tton 1 for less than one second; the isplay indicates the speed level. utton 1 pressed longer than one second top speed is elected. otor stopping and decreasing speed 2 for less an one second; the display indicates the speed level. eeping button 1 pressed longer than one second turns the hood off. imer Function s after ou have activated this function. To program: press button 3. tion is activated you will see the number displayed ulsing on and off. ight on-off function n and off by pressing button 4. C S The Cooker hood motor is turned on by pressing button 1. a Speed is increased by pressing bu d Keeping b s M The fan operating speed is decreased by pressing button th K T This function allows you to program the cooker hood’s motor and lights in order to have them automatically switched off fifteen minute y When the timer func p L The light is turned o 9

etal filters cleaning required warning ing “A” on the display, that it is time to clean the metal rease filters. ill guarantee better ducting performance and proved hygiene. e an mber “8” will be displayed, it will isappear after four seconds. filters’ cleaning clock and begin the ountdown to the next prompt. arbon filters replacement warning (only if mounted) ted air. It is necessary set the cooker hood’s controls accordingly. od is ot in operation, hold down button 3 for more than 4 seconds. he eaning that the hood is now aware that there are carbon lters fitted. s of use. This indicates that the carbon filters require placement. o processor will reset and begin the 120 our countdown once more. S Your cooker hood’s electronic system is equipped with spec d M Every thirty hours of utilisation the microprocessor warns the user, by means of a puls g Cleaning the filters w im To delete this prompt, once the filters have been cleaned and with th cooker hood off (not powered). Hold buttons 2 and 3 for more th four seconds: on screen the nu d The microprocessor will reset the c C If your cooker hood is used in recirculation mode, it will need to have active carbon filters fitted to purify the recircula to After fitting the carbon filter (see relevant section), whilst the ho n On the display, the symbol “-” will be displayed, this means that t hood, for the time being, is not utilising the carbon filters. If you continue to hold down button 3, after a further 4 seconds the letter “C” will appear, m fi From now on the appliance will display a pulsing “C” on the display every 120 hour re To reset the carbon filters replacement warning you should do the following. When the cooker hood is switched off (i.e. not connected t the mains supply), hold buttons no. 1 and no. 3 for more than four seconds: on screen the number “8” will be displayed. It will disappear after four seconds; the micro h

C IMPORTANT: BEFORE CLEANING, ALWAYS ENSURE THAT YOU HAVE SWITCHED YOUR COOKER HOOD OFF AT THE OMNI-POLAR SWITCH, SET AT THE WALL FROM THE CABLE. le n oker hood with mild liquid o ase filter grill with mild liquid o carbon filter”). A build up of grease o Never attempt to clean the area above the grease filters. he grease filter C a ing Clean the external parts of your co o detergent and a new damp cloth. o Never use abrasive powder, corrosive solvents or brushes. o Never insert pointed objects into the motor’s protective grid. Only clean the control panel and gre detergents and a new damp cloth. If you are using the appliance in recirculation mode, then be sure to replace the carbon filter at the recommended interval (see section on “Fitting the could cause a fire hazard. T o ticles to protect your kitchen & furniture from greasy o mmable if it becomes o . t month, using hot water and normal washing-up o DO NOT WASH THE GREASE FILTER IN A DISHWASHER. Your cooker hood includes a grease filter which helps to absorb grease par residues. This metallic filter may become infla saturated with this greasy residue. To prevent this fire hazard, the filter should be cleaned regularly Depending on use, this should be done every 10-15 days or a least once a detergent.

o Undo the side catches. Soak the grease filter in hot water and washing up liquid for se filters dry thoroughly before refitting them in the cooker hood. o First remove the grease filter by pulling down on it. o about an hour. o Rinse them off thoroughly with hot water. o Repeat the process if required. 12 o Refit the grease filters once they have dried. o IMPORTANT: Let the grea

A LIGHT BULB, YOU MUST ENSURE THAT YOU HAVE DISCONNECTED THE COOKER HOOD FROM NS S P o Remove the grease filters (as described on page 11). o n. o Find the bulb that re ement, you will find it located in the light fi on of the canopy. new E14 50W (max) bulb. o iately. If the lights still do not work, make sure that the lamps are fitted before you call for technical o Refit the grease filters. Changing a light bulb IMPORTANT: BEFORE ATTEMP U PLY. YOUR MAI Prior to touching the light bulbs ensure they are cooled dow quires replac xture which is inside the exposed secti o Unscrew the light bulb that needs to be replaced and insert a IMPORTANT: Defective bulbs should be replaced immed o properly into their housings assistance.

If the appliance is being use 14 d to be used in recirculation mode then it is necessary to fit carbon filters. This will help to absorb unpleasant b YOU HAVE DISCONNECTED THE COOKER HOOD FROM YOUR MAINS SUPPLY. ) Remove the grease filters. filter over e pins that are located at the nd of the motor. ) Turn the carbon filter anticlockwise, until you feel click into place. o Repeat this process for the second carbon filter. You need to ither end of the motor. o should be replaced every three months, when filter replacement warning activates or if they show signs of damage. y cooking. IMPORTANT: BEFORE ATTEMPTING TO FIT OR REMOVE THE CARBON FILTERS, YOU MUST odours caused ENSURE THAT 1 2) Hook the carbon th e 3 it place a carbon filter at e o Refit the grease filters. The carbon filters the carbon

all the instructions and make sure that the voltage (V) and the frequency (Hz) indicated on the rating plate are exactly the same as the voltage and freq r all the accident prevention regulations in force, normal use and the regular operation of the O R PE o ble must be fitted upstream from the electrical connection, using an omni-polar switch with a contact connected by a competent person, using uency in your home. The rating plate can be found behind the grease filters. The manufacturer declines all responsibility in the event of the installe failing to observe which are necessary for electric system. Electrical connection Y U COOKER HOOD IS INTENDED FOR FITTED AND RMANENT INSTALLATION. o The power cable must be connected to the terminals marked L (live) and N (neutral) in the hood and fixed with a cable clamp. The cooker hood’s power ca distance of at least 3 mm. WARNING: THIS APPLIANCE MUST BE EARTHED. It should only be 15 fixed wiring via a double pole switched fused spur outlet. (UK ONLY). We recommend that the appliance is connected by a qualified electrician, who is a member of the N.I.C.E.I.C. and who will comply ith t colou w he I.E.E. and local regulations. The wires in the mains lead are red in accordance with the following UK code: Blue = Neutral, Brown = Live, Green/Yellow = Ground

h th c in your spur box, p ea o The blue wire must be connected to the o The brown wire must be connected to the al marked “L” (live), or coloured red. Be r o socket available that will be accessible once the hood is mounted. If the product is going to be used in extraction mode, ly e o inside the product and insure that there is no transit packaging or any other materials, such as packets of screws, o all and ceiling. If this is not possible, then a thick, protective covering o Select a flat surface for assembling the cooker hood. Cover that only find two wires in the main’s lead (blue and brown), n neither must be connected to the earth terminal. o correspond wit e oloured markings identifying the terminals l se proceed as follows: terminal marked “N” (neutral), or coloured black. termin fo e beginning installation Check that the product purchased is of a suitable size for the chosen installation area. In addition check whether there is an electrical then there should also be space to connect a ducting hose to the outside. o Carry out all necessary masonry work prior to the fitting of the cooker hood. o Ensure that all electrical connections are carried out by a suitab qualified person. o Before commencing installation of the cooker hood the greas filter should be removed. Check guarantees etc. These should be removed and kept for future use. If possible, disconnect and move freestanding or slot-in cookers from their position, to provide easier access to the rear w should be placed over the worktop, hob top or cooker. This will help to protect these surfaces from damage and debris. surface with a protective covering and place all cooker hood parts and fittings on it.

going to use the appliance in extractor mode, you should also ce o er a qualified technician must verify the suitability of the materials, in accordance with the type of wall ke o Do not tile, grout or silicone this appliance to the wall. This e surface mounted only. y EFORE E ION MODE OR RECIRCULATION MODE. PLEASE TURN TO PAGE 23 NOW TO o ker hood should not be exposed to a direct heat source from the cooking device underneath it, i.e. naked flame from a n them. o o The lights on this appliance should only be used during operation of the cooker hood. They should not be left on permanently and MPORTANT: YOUR COOKER HOOD SHOULD BE CONNECTED TO In addition check whether there is an electrical socket available, which will be acc ensure that there is space to connect a fumes discharge devi to the outside. Raw plugs are provided to secure the hood to most types of walls and ceilings. Howev and ceiling. The wall and ceiling must be strong enough to ta the weight of the hood. appliance is designed to b our cooker hood IMPORTANT: YOU WILL HAVE TO DECIDE B INSTALLING YOUR COOKER HOOD WHETHER TO US IT IN EXTRACT Installing UNDERSTAND THE DIFFERENCES BETWEEN THESE TWO MODES. The coo gas burner or heat from electric hob zones without a pan o We recommend that at least two people install this hood. used as a lighting source. I YOUR MAINS SUPPLY AFTER THE REST OF THE INSTALLATION PROCESS HAS BEEN COMPLETED. 1) Remove the metal grease filters.

that you are intending to install it on and mark the position of the support holes that are to be drilled (as shown in the figure below). 2a) The support screw holes are indicated by figure A in this drawing and the anchoring screw holes are indicated by figure B. 3) Using a drill bit with a 6 mm diameter, make holes in the wall on the positions that you have marked in step 2. 4) Insert raw plugs into all of the holes that you have drilled. 18

halfway in, leaving them 10 mm out of the wall. 6) Hang the hood onto the support screws. 7) Fully tighten the support screws (A) and then screw the anchoring screws (B) through the relevant holes in the cooker hood. Tighten the anchoring screws fully into the wall 19

8) Connect the coupling to the top of the cooker hood, and then connect a 125 mm ducting hose to the coupling (please note that the ducting hose is not supplied with the appliance). o The other end of the ducting hose should be connected to your discharge outlet that is suitable for cooking vapours. It should have a cross section of at least 150 cm². o The maximum distance between the coupling and your discharge outlet should be 3 metres, with one 90 degree bend. Fitting the chimney 9) Take the two chimney sections (C and D). o Rest the bottom of chimney section C on the top of the hood. You should take care to position the tabs on the chimney section into the rear of the hood. 20 cil. o Mark the side measurement of both sides of chimney section C on the wall with a pen

o Mark the side measurement of both sides of chimney section D 1) Take the fixing bracket (E) and place it between the two pencil o Keeping the bracket in contact with the wall, use a pencil to mark on the wall the anchoring holes that are cut out of the bracket 1 must ensure that it is perpendicular to the hood. on the wall with a pencil and then remove chimney section D. 1 marks that you made in step 9

o Refit chimney section C to the hood and fix it onto the hood using the two screws that are supplied. o Secure the top of chimney section C to the fixing bracket, using the screws provided. ng the same method as 3) Lift ch cure it to the fixing racket using the screws provided. lectrical connection he electrical connection must correspond to the electrical requirement oted on the rating plate, which is placed inside the cooker hood. The ppliance should be connected to the electrical supply. See page 15 – 6 for detailed information on the electrical connection. ) Using a 6 mm drill bit, drill out two holes on the pencil marking t ou made in step 11. Insert raw plugs into the holes and then o Slide chimney section D inside of chimney section C. Then secure the upper bracket to the wall, usi you have just used to secure the lower bracket. 1 imney section D up to the ceiling and se b E T n a 1

hat is the difference between extraction and recirculation mo To ge will be taken out of the room via external ducting. r from an outside all, this may not be possible. The only alternative is to recirculate the hat is a All cooker hoods have a grease filter but if you are using your cooker o the grease filter. W des? t optimum performance from your cooker, the air Unfortunately if you live in a flat or the hood is too fa w air. In recirculation mode stale air is taken via the grease filter, and passed through a charcoal filter for purification. The air then re-enters the kitchen via an opening in the hood. W charcoal filter and do I need one? hood in recirculation mode, then a charcoal filter must be fitted in addition t

roperly, before contacting the Baumatic Service Department, lease refer to the checklist below. My cooker hood will not start. o Check that the hood is connected to the electricity supply o Check that the fan speed control is set correctly. My cooker hood is not working effectively. o The fan speed is not set high enough o The kitchen is not well ventilated enough. h ode, check that the carbon filters do not need replacing. cting hose and discharge outlet are not blocked. My cooker hood has switched off during operation. The safety cut-out device has been tripped. safety cut-out device to reset. o IMPORTANT: If you have installed your cooker hood too low, . Your cooker hood may become damaged if the safety cut-out device is tripped DO NOT MAKE ANY ATTEMPT TO REPAIR THE APPLIANCE T I p p o The grease filter is dirty and requires cleaning. o If t e hood is set up for recirculation m o If the hood is set up for extraction mode, check that the du o o Turn off the hob and then wait for the the safety cut-out device will frequently trip frequently. YOURSELF. IF THE APPLIANCE IS STILL NOT OPERATING CORRECTLY, PLEASE CONTACT THE BAUMATIC SERVICE DEPARTMENT ON TELEPHONE NUMBER (0118) 933 6911.

er Your new Bau ic appliance comes complete with a free 12 month guarantee covering both parts and labo i mon a applies t Scotland, Wales and Northern Ireland only. To q i to b v g the guar * In liance is covered by a 5 year parts warranty. Baumatic Ltd will provide free of charge the parts required to repair the appliance, only if they are fitted by a Baumatic engineer, for any defect that arises due to faulty materials or workmanship within a period of 5 years from the original p * w Shoul the policy he guarantee covers the appliance for normal domestic use only, unless otherwise stated. ny claims made under the terms of the guarantee must be supported by the original invoice/bill of sale his guarantee is transferable only with the written consent of Baumatic Ltd. s t will not be offered. he guarantee does not cover: damage or wilful abuse. allation k, paintwork, plastic items, covers, baskets, trays, shelves, burner bases, burner caps, decals, corrosion, rubber seals. the course of the work carried out it may be necessary to remove the appliance from it operating oever in this process. ghts. nical/Advice EL: 0118 933 6900 TEL: 0118 933 6911 TEL: 0118 933 6922 0118 933 6933 epublic of Ireland), please contact one of the numbers below: EL: 01 – 6266798 FAX: 01 - 6266634 Tha y aumatic. * Ap s labour & 1 year parts warranty only) Baum Dear Custom , mat ur costs resulting from defective materials or workmanship. Baumat c also gives you the opportunity to automatically extend the guarantee period for a further 12 ths t no extra cost, giving an initial guarantee period of 24 months. The extended guarantee period o England, ual fy for your full 24 months guarantee you must register your appliance within 28 days of purchase e co ered under this guarantee. This can be done online via: www.baumatic.co.uk or through returnin antee card which can be found in each new Baumatic appliance. addition, your app urchase date. An additional 1 to 3 year insurance scheme for labour is available should you wish to extend the arranty period. d any person other than an authorised representative of Baumatic Ltd interfere with the appliance, is negated and Baumatic Ltd will be under no further liability. T A issued at the time of purchase. T If the appliance fails and is considered either not repairable or uneconomical to repair between 12 month (2 years if registered) and five years, a free of charge replacemen The guarantee for any replacement will only be for the remainder of the guarantee on the original product purchased. T - Sinks and taps - Failure to comply with the manufacturers instructions for use. - The replacement of cosmetic components of accessories - Accidental - Subsequent loss or damage owing to the failure of the appliance or electrical supply - Incorrect inst - Losses caused by Acts of God, civil war, failure to obtain spare parts, strikes or lockouts - Filters, fuses, light bulbs, external hoses, damage to bodywor In position. Whilst all reasonable care will be taken, Baumatic Ltd cannot accept responsibility for damage sustained to any property whats This guarantee is in addition to and does not diminish your statutory or legal ri Contacting Baumatic Ltd Sales Service Spares Tech T FAX: 0118 931 0035 FAX: 0118 986 9124 FAX: 0118 933 6942 0118 933 6942 For ROI (R T nks ou for buying B plie to UK, Scotland, Wales & Northern Ireland only (Republic of Ireland has 1 year

+44 118 933 6911 Service Fax +44 118 986 9124 Spares Telephone +44 118 933 6922 Technical / Advice Telephone +44 118 933 6933 6 Bennet Road, Sales Telephone +44 118 933 6900 Sales Fax +44 118 931 0035 Service Telephone E-mail: [email protected] tech uk [email protected]. Website: http://www.baumatic.com