Craftsman 143 Owner's Manual

OWNER'SMANUAL o Assembly Operation Customer Responsibilities Service Adjustments Repair Parts Caution: Read and Follow all Safety Rules and Instructions Before Operating This Equipment 160904 05.20.97 VBL Printed in U.S.A_

OBJECTS. FAILURE TO OBSERVE THE FOLLOWING SAFETY INSTRUCTIONS COULD RESULT IN SERIOUS INJURY OR DEATH. SAFETY STANDARDS REQUIRE OPERATOR PRESENCE CONTROLS TO MINIMIZE THE RISK OF INJURY. YOUR UNIT IS EQUIPPED WITH SUCH CONTROLS. DO NOT ATTEMPT TO DEFEAT THE FUNCTION OF THE OPERATOR PRESENCE CONTROLS UNDER ANY CIRCUMSTANCES. TRAINING: • Read this operator's manual carefully. Become familiar with the controls and know how to operate your mower properly. Learn how to quickly stop mower. • Do not allow children to use your mower. Never allow adults to use mower without proper instructions. • Keep the area of operation clear of atl persons, especially small children and pets. • Use mower only as the manufacturer intended and as de- scribed in this manual. • Do not operate mower if it has been dropped or damaged in any manner, Always have damage repaired before using your mower. • Do not usaaccessory attachments that are not recommended by the manufacturer. Use of such attachments may be hazardous. • The blade turns when the engine is running, PREPARATION: • Always thoroughly check the area to be mowed and clear it of all stones, sticks, wires, bones, and other foreign objects. These objects wilt be thrown by the blade and can cause severe injury. • Always wear safety glasses or eye shields when starting and while using your mower. • Dress properly. Do not operate mower when barefoot or weadng open sandals. Wear only solid shoes with good traction when mowing, • Check fuel tank before starting engine. Do not fill gas tank indoors, when the engine is running o rwhen the engine ishot. Allow the engine to cool for several minutes before filling the gas tank. Clean off any spilled gasoline before starting the engine. • Always make wheel height adjustments before starting your mower. Never attempt to do this while the engine is running. • Mow only in daylight or good artificial light. OPERATION: • Keep your eyes and mind on your mower and the area being cut. Do not let other interests distract you. • Do not mow wet or slippery grass. Never run while operating your mower. Always be sure of your footing - keep a firm hold on the handles and walk. • Do not put hands or feet near or under rotating parts. Keep clear of the discharge opening at all times. • Always stop the engine whenever you leave or are not using your mower, or before crossing driveways, walks, roads, and any gravel-covered areas. • Never direct discharge of material toward bystanders nor allow anyone near the mower while you are operating it. • Before cleaning, inspecting, or repaidng your mower, stop the engine and make absolutely sure the blade and all moving parts have stopped. Then disconnect the spark plug wire and keep it away from the spark plug to prevent accidental starting. • Do not continue to run your mower if you hit a foreign object. Follow the procedure outlined above, then repair any dam- age before restarting and operating you mower, • Do not change the governor settings or overspeed the engine. Engine damage or personal injury may result. • Do not operate your mower if it vibrates abnormally. Exces- sive vibration is an indication of damage; stop the engine, safely check for the cause of vibration and repair as required. • Do not run the engine indoors. Exhaust fumes are danger- ous. • Never cut grass by pulling the mower towards you. Mow across the face of slopes, never up and down or you might Ioseyourfooting. Do notmowexcessivelysteepslopes. Use caution when operating the mower on uneven terrain orwhen changing directions - maintain good footing. • Never operate your mower without proper guards, plates, grass catcher or other safety devices in place. MAINTENANCE AND STORAGE: • Check the blade and the engine mounting bolts often to be sure they are tightened properly. • Check all bolts, nuts and screws at frequent intervals for proper tightness to be sure mower is in safe working condi- tion. • Keep a!l safety devices in place and working. • To reduce fire hazard, keep the engine free of grass, leaves or excessive grease and oil. • Check grass catcher often for deterioration and wear and replace worn bags. Use only replacement bags that are recommended by and comply with specifications of the manufacturer of your mower. • Always keep a sharp blade on your mower. • Allow engine to cool before storing in any enclosure. • Never store mower with fuel in the tank inside a building where fumes may reach an open flame or an ignition source such as a hot water heater, space heater, clothes dryer, etc. & Look for this symbol to point out im- portant safety precautions. It means CAUTION!H BECOMEALERT!!! YOUR SAFETY IS INVOLVED. CAUTION: Always disconnect spark plug wire and place wire where it can- not contact spark plug in order to pre- vent accidental starting when setting up, transporting, adjusting or making • repairs. WARNING The engine exhaust from this product con- tains chemicals known to the State of Califor- nia to cause cancer, birth defects, or other reproductive harm.

Mower. It has been designed, engineered and manufac- tured to give you the best possible dependability and performance. Should you experience any problem you cannot easily remedy, please contact your nearest Sears Authorized Service Center/Department. We have competent, well- trained technicians and the proper tools to service or repair this lawn mower. Please read and retain this manuat. The instructions will enable you to assemble and maintain your lawn mower }roperly. Always observe the "SAFETY RULES". MODEL NUMBER 917.377201 SERIAL NUMBER DATEOFPURCHASE THE MODEL AND SERIAL NUMBERS WILL BE FOUND ON A DECAL ATTACHED TO THE REAR OF THE LAWN MOWER HOUSING YOUSHOULDRECORDBOTHSERIALNUMBERAND DATE OFPURCHASEAND KEEPIN A SAFE PLACE FOR FUTURE REFERENCE. PRODUCT SPECIFICATIONS HORSEPOWER: 5.5 DISPLACEMENT: 11.5 CU. IN. GASOLINE CAPACITY !.5 QUARTS AND TYPE: UNLEADED REGULAR OIL TYPE (APt-SF/SGiSH): SAE 30 {ABOVE 32°F) SAE 5W-30 {BELOW 32°F) OIL CAPACITY: 20 QZS. SPARK PLUG: CHAMPION RJ19LM (GAP: .030") VALVE CLEARANCE: INTAKE: .00@- .008 EXHAUST: .004 - .008 SOLID STATE IGNITION AIR GAP: ,0125 IN. BLADE BOLT TORQUE: 35-40 FT. LBS. MAINTENANCE AGREEMENT A Sears Maintenance Agreement is available on this product. Contact your nearest Sears store for details. CUSTOMER RESPONSIBILITIES * Read and observe the safety rules. = Follow a regular schedule in maintaining, caring for and using your lawn mower. , Follow the instructions under "Customer Responsibilities" and "Storage" sections of this owner's manual. LIMITED TWO YEAR WARRANTY ON CRAFTSMAN POWER MOWER For two (2) years from date of purchase, when this Craftsman Lawn Mower is maintained, lubricated, and tuned up according to the operating and maintenance instructions in the owner's manual, Sears will repair free of charge any defect in material or workmanship. If this Craftsman Lawn Mower is used for commercial or rental purposes, this warranty applies for only 90 days from the date of purchase. This Warranty does not cover: - Expendable items which become worn during normal use, such as rotary mower blades, blade adapters, belts, air cleaners and spark plug. = Repairs necessary because of operator abuse or negligence, including bent crankshafts and the failure to maintain the equipment according to the instructions contained in the owner s manual. WARRANTY SERVICE IS AVAILABLE BY RETURNING THE CRAFTSMAN POWER MOWER TO THE NEAREST SEARS SERVICE CENTER/DEPARTMENT IN THE UNITED STATES. THIS WARRANTY APPLIES ONLY WHILE THIS PRODUCT IS IN USE IN THE UNITED STATES. This Warranty gives you specific legal rights, and you may also have other rights which vary from state to state. SEARS, ROEBUCK AND COo, D/817 WA, HOFFMAN ESTATES, ILLINOIS 60179 3

SAFETY RULES ............................................................ 2 PRODUCT SPECIFICATIONS ...................................... 3 CUSTOMER RESPONSIBJL|TIES ....................... 3, 9=11 WARRANTY ................................................. ................. 3 ASSEMBLY ................................................................... 5 OPERATION .................................................................. 6 MAINTENANCE SCHEDULE ........................................ 9 SERVICE AND ADJUSTMENTS ................................. 12 STORAGE ................................................................... 14 TROUBLESHOOTING ................................................. 23 REPAIR PARTS- LAWN MOWER ........................ 15-19 REPAIR PARTS- ENGINE .................................... 20-22 PARTS ORDERING!SERVICE .................................... 24 DEX A Accessories .................................... 5 Adjustments: Carburetor ............................. 13 Drive Bett ............................... 12 Engine Speed ........................ 13 Handle Height ........................ 13 Height of Cut ............................ 7 Air Filter: Replacement ......................... 11 Service ................................... 11 Assembly ........................................ 5 B Blade: Sharpening ............................ 10 Replacement ......................... 10 C Controls: Drive Control ............................ 6 Engine Zone Control ................ 6 Engine Speed Control ............. 6 Operator Presence Control Bar .............................. 6 Customer Responsibilities ..... 3, 9-11 Air Filter ................................. ! 1 Blade Care/Replacement ...... 10 Drive Wheels ......................... 10 Engine ................................... 11 Lubrication ............................... 9 Spark Plug ............................. 11 Cutting Leveis ................................ 7 E Engine: Air Filter ................................. 11 QiI Change ............................. 11 Oil Level ................................. 11 Oil Type ................................. 11 Starting .................................... 8 Stopping .................................. 8 Storage .................................. 14 F Fuel: Capacity ................................... 3 Storage .................................. 14 Type ......................................... 8 H Handle Adjustment: Assembly ................................. 5 Cutting Height ........................ 13 L Lubrication: Engine ................................... 11 Lawn Mower ............................ 9 M Maintenance Agreement ................ 3 Maintenance Schedule ................... 9 Mowing Tips ................................... 8 Oil: O Engine ................................... 11 Storage .................................. 14 Operation: Drive Control ............................ 7 Engine Control ......................... 7 Grass Catcher ......................... 7 Mower ...................................... 7 Operator Presence Control Bar .............................. 7 Options: Accessories ............................. 5 R Repair Parts: Engine .............................. 20-22 Lawn Mower ..................... 15-19 Responsibilities, Customer .... 3, 9-tl S Safety Rules ................................... 2 Service and Adjustments ............. 12 Carburetor ............................. 13 Drive Belt ............................... 12 Engine Speed ........................ 13 Handle ................................... 13 Spark Plug .................................... 11 Specifications ................................. 3 Speed Control: Engine ..................................... 7 Starting the Engine ......................... 8 Stopping the Engine ....................... 8 Storage ......................................... 14 T Trouble Shooting Chart ................ 23 W Warranty ......................................... 3 &

They are also available at most Sears retail outlets and service centers. Most Sears stores can also order repair parts for you, when you provide the model number of your lawn mower. Some of these accessories may not apply to your lawn mower. LAWN MOWER PERFORMANCE CLIPPING DEFLECTOR FOR REAR DISCHARGE LAWN MOWERS GRASS CATCHERS FOR REAR DISCHARGE LAWN MOWERS \ \ LAWN MOWER MAINTENANCE MULCHER KITS I_ GRASS CATCHERS FOR SIDE DISCHARGE LAWN MOWERS f STABlUZER GAS CANS MUFFLERS BLADES AIR FILTERS BLADE ADAPTERS WHEELS SPARK PLUGS ENGINE OIL Read these instructions and this manual in its entirety before you attempt to assemble or operate your new lawn mower. Your new lawn mower has been assembled atthe factory with the exception of those parts left unassembled for shipping purposes. All parts such as nuts, washers, bolts, etc., necessary to complete the assembly have been placed in the parts bag. To ensure safe and proper operation of your lawn mower, all parts and hardware you assemble must be tightened securely. Use the correct tools as necessary to ensure proper tightness. TO REMOVE LAWN MOWER FROM CARTON = Remove loose parts included with mower. - Cut down two end corners of carton and lay end panel down flat. , Remove all packing materia s except padd ng between upper and lower handle and padding holding operator presence control bar to upper handle. = Roll lawn mower out of carton and check carton thor- oughly for additional loose parts. HOW TO SET UP YOUR LAWN MOWER TO UNFOLD HANDLE (See Fig= 1) IMPORTANT: UNFOLD HANDLE CAREFULLY SO AS NOT TO PINCH OR DAMAGE CONTROL CABLES. i, irlll ASSEMBLY OPERATOR PRESENCE CONTROLBAR LiFT UP MOWING POS_TION LOWER HANDLE FiG. 1 • Raise handles until lower handle section locks into place in mowing position. Raise protective padding, raise upper handle section into place on lower handle and tighten both handle knobs. , Remove handle padding holding operator presence control bar to upper handle. , Your lawn mower handle can be adjusted for your mowing comfort. Refer to "Adjust HandW' in the 5 Service and Adjustment section of this manual.

READ THiS OWNER'S MANUAL AND SAFETY RULES BEFORE OPERATING YOUR LAWN MOWER. Compare the illustrations with your lawn mower to familiarize yourself with the location of various controls and adjustments. Save this manual for future reference. These symbols may appear on your lawn mower or in literature supptied with the product. Learn and understand their meaning. - i\1 SLOW CHOKE ENGINE ENGINE ON OFF CAUTION FAST FUEL OR WARNING OIL DANGER, KEEP HANDS AND FEET AWAY OPERATOR PRESENCE CONTROL BAR DRIVE CONTROL LEVER ENGINE ZONE CONTROL CABLE DRIVE CONTROL STARTER HANDLE HANDLE KNOB ENGINE OiL CAP WiTH DIPSTICK ,1. GASOLINE FILL CAP I ENGINE SPEED CONTROL LEVER DRIVE COVER MULCNER DOOR WHEEL ADJUSTER HOUSING (ON EACH WHEEL) MEETS CPSC SAFETY REQUIREMENTS Sears rotary walk-behind power lawn mowers conform to the safety standards of the American National Standards Institute and the U.S. Consumer Product Safety Commission. The blade turns when the engine is running. OPERATOR PRESENCE CONTROL - must be held down to the handle to start the engine. Release to stop the engine. PRIMER - pumps additional fuel from the carburetor to the cylinder for use when starting a cold engine. STARTER HANDLE - used for starting the engine. DRIVE CONTROL LEVER - used to engage power-pro- pelled forward motion of lawn mower. MULCHER DOOR - allows cOnversion to discharge or bagging operation. ENGINE SPEED CONTROL LEVER - must be in the fast (,_) position for starting and mowing. 6

result in severe eye damage. Always wear safety glasses or eye shields while operating your lawn mower or performing any adjustments or repairs. We recommend a wide vision safety mask over the spectacles or standard safety glasses. HOW TO USE YOUR LAWN MOWER TO ADJUST CUTTING HEIGHT (See Fig. 4) ENGINE SPEED CONTROL (See Fig. 2) The engine speed is controlled by a lever located on the side of the engine. Fast position is for starting the engine, normal cutting and better grass bagging. Stow position is for light cutting, trimming and fuel economy. ENGINE SPEED CONTROL FiG. 2 ENGINE ZONE CONTROL CAUTION: Federal regulations require an engine control to be installed enth s lawn mower in order to minimize the risk of blade contact injury. Do not under any circumstances attempt to defeat the function of the operator con= trol, The blade turns when the engine is running. Your lawn mower is equipped with an operator pres- ence control bar which requires the operator to be positioned behind the lawn mower handle to start and operate the lawn mower. DRIVE CONTROL (See Fig. 3) - Self-propelling is controlled by holding the operator presence control bar down to the handle and pushing the drive control lever forward until it clicks; then release the lever. , Forward motion will stop when the operator presence control bar is released. To stop forward motion without stopping engine, release the operator presence control bar slightly until the drive control disengages. Hold operator presence control bar down to handle to con- tinue mowing without self-propelling. * To keep drive control engaged when turning corners, push down on handle and lift front wheels off ground while turninq lawn mower. OPERATOR PRESENCE CONTROL BAR TOENGAGE DRIVE C_ONTROL DRIVE CONTROL FIG. 3 DRIVE CONTROL DISENGAGE_ = Raise wheels for low cut and lower wheels for high cut. Adjust cutting height to suit your requirements. Me- dium position is best for most lawns, To change cutting height, squeeze adjuster lever to- ward wheel. Move wheel up or down to suit your requirements. Be sure all wheels are in the same setting. NOTE: Adjuster is properly positioned when plate tab inserts into hole in lever. Also, 9-position adjusters (if so equipped) allow lever to be positioned between the plate tabs. LOWER WHEELS PLATETAB FORHIGHCUT RAISE WHEELS FOR LOW CUT _=._ _ FiG. 4 NOTE: Your lawn mower has been shipped ready for mulching operation. To convert to discharging operation, you must install the discharge deflector attachment in- cluded with your mower. TO INSTALL DISCHARGING DEFLECTOR (See Fig. 5) • Lift door upward on it's hinge until the deflector frame can be hooked over the door mounting bracket as shown. , Release the door to rest against deflector frame. To return to mulching operation, reverse the above steps and be sure door is in closed position. .< . ._.4._ MULCHER DOOR DEFLECTOR _- << _ -- :'-.s_ , t FiG. 5 BEFORE STARTING ENGINE OIL (See Fig. 6) Your lawn mower is shipped without oi! in the engine. Be sure mower is level and area around oil fill is clean. Remove engine oil cap w!dipstick and fill to the full line on the dipstick.

"ENG{NE" in Customer Responsibilities section of this manuaI. • Pour oil slowly. Do not over fill. Check oil level before each use. Add oil if needed. Fill to full line on dipstick. = To read proper level, tighten engine oil cap each time. Reinstall engine oil cap and tighten. = Change the oil after every 25 hours of operation or each season You may need to change the oil more often under dusty, dirty conditions. GAS (See Fig. 6) o Fill gasoline tank with fresh, clean, unleaded gasoline. DO NOT USE PREMIUM GASOLINE. BE CAREFUL NOT TO OVER FILL TANK, WARNING: Experience indicates that alcohol blended fuels (called gasohol or using ethanol or methanol) can attract moisture which leads to separation and formation of acids during storage. Acidic gas can damage the fuel system of an engine while in storage. To avoid engine problems, the fuel system should be emptied before stor- age of 30 days or longer. Drain the fuet tank, start the engine and let it run until fuel lines and carburetor are empty. Use fresh fuel next season. See Storage Instruc- tions for additional information. Never use engine or carburetor cleaner products in fuel tank or permanent damage may occur. TO START ENGINE • To start a cold engine, push primer five (5) times before trying to start. Use a firm push. This step is not usually necessary when starting an engine which has already run for a few minutes. o Hold operator presence control bar down to the handle and pull starter handle quickly. DO NOT allow starter rope to snap back. - To STOP engine, release operator presence control bar. NOTE: In cooler weather it may be necessary to repeat priming steps. In warmer weather over priming may cause flooding and engine will not start, if you do flood engine, wait a few minutes before attempting to start and DO NOT repeat priming steps. MOWING TiPS - Under certain conditions, such as very tall grass, it may be necessary to raise the height of cut to reduce pushing effort and to keep from overloading the engine and leaving clumps of grass clippings. o For extremely heavy cutting, reduce thewidth of cut by overlapping previously cut path and mow slowly. For better grass bagging and most cutting conditions, the engine speed should be set in the fast position. o For side discharge lawn mowers, cutting in a counter- clockwise direction, starting at the outside of the area to be cut, spreads grass clippings more evenly and puts less load on the engine. To keep clippings off of walkways, flower beds, etc., make the first cuts in a clockwise direction. Pores in cloth grass catchers can become filled with dirt and dust with use and catchers will collect less grass. To prevent this, regularly hose catcher off with water and let dry before using. Keep top of engine around starter clear and clean of grass clippings and chaff. This will help engine air flow and extend engine life. GASOLINE FILLER CAP / ENGINE OiL CAP W/DIPSTICK FIG, 6 MULCHING MOWING TIPS IMPORTANT: FOR BEST PERFORMANCE, KEEP MOWER HOUSING FREE OF BUILT-UP GRASS AND TRASH. SEE "CLEANING" JNCUSTOMER RESPONSIBILITIES SECTION OF THIS MANUAL. • The special mulching blade will recut the grass clip- pings many times and reduce them in size so that as they fall onto the lawn they will disperse into the grass and not be noticed. Also, the mulched grass will biodegrade quickly to provide nutrients for the lawn. Always mulch with your highest engine (blade) speed as this wilt provide the best recutting action of the blades. * Avoid cutting you r lawn when it is wet. Wet grass tends to form clumps and interferes with the mulching action. The best time to mow your lawn is the early afternoon. At this time the grass has dried and the newly cut area will not be exposed to the direct sun. For best results, adjust the lawn mower cutting height so that the lawn mower cuts off only the top one-third of the grass blades (See Fig. 7). tf the lawn is over- grown it will be necessary to raise the height of cut to reduce pushing effort and to keep from overloading the engine and leaving clumps of mulched grass. For extremely heavy mulching, reduce your width of cut by overlapping previously cut path and mow slowly. - Certain types of grass and grass conditions may re- quire that an area be mulched a second time to com- pletely hide the clippings. When doing a second cut, mow across or perpendicular to the first cut path. = Change your cutting pattern from week to week. Mow north to south one weekthen change to east to west the next week. This will help prevent matting and graining of the lawn. MAX 1/3 8 FIG. 7

AS YOU COMPLETE REGULAR SERVICE Check for Loose Fasteners CIeanllnspect Grass Catcher (If Equipped) M Clean Lawn Mower O Clean Under Drive Cover W (Power-Propelled Mowers) Check drive belt/pulleys E Power-Proj?elled Mowers) R Check/Sharpen/Replace Blade _3 Lubrication Chart Clean Battery/Recharge (Electric Staff Mowers) E Check Engine Oil Level N ine Oil G Clean Air Filter Inspect Muffler N Clean or Replace Spark Plug E Replace Air Filter Paper Cartridge _t_4'2 I - Change more often when operating under a heav load or in high ambient temperatures, 2 - Service more often when operating in dirty or dusty conditions. 3 - Replace blades more often when mowing in sandy soil, 4 - Charge 48 hours at end of season. SERWCE DATES GENERAL RECOMMENDATIONS The warranty on this awn mower does not cover items that have been subjected to operator abuse or negligence. To receive full value from the warranty, operator must maintain mower as instructed in this manual. Some adjustments will need to be made periodically to properly maintain your unit. All adjustments in the Service and Adjustments section of this manual should be checked at least once each season. Once a year, replace the spark plug, clean or replace air filter element and check blade for wear. A new spark plug and clean/new air filter element assures proper air-fuel mixture and helps your engine run better and last longer. • Follow the maintenance schedule in this manual. BEFORE EACH USE ,, Check engine oil level. - Check for loose fasteners. LUBRICATION Keep unit well lubricated (See "LUBRICATION CHART"), LUBRICATION CHART (_) WHEEL ADJUSTER RiNG BRACKET (_ MULCHER DOOR (_) ENGINE OIL (_ HANDLE BRACKET MOUNTING P_N (_ SPRAY LUBRICANT (_) REFER TO CUSTOMER RESPONS|BILITIES "ENGINE" SECTION, 1IMPORTANT: DO NOT OIL OR GREASE PLASTIC WHEEL BEARINGS. VISCOUS LUBRICANTS WILL ATTRACT DUST AND DiRT THAT WILL SHORTEN THE LIFE OF THE SELF LUBRICATING BEARINGS. IFYOU FEEL THEY MUST BE LUBRICATED, USE ONLYA DRY, POWDERED GRAPHITE TYPE LUBRICANT SPARINGLY. 9

nance. TIRES • Keep tires free of gasoline, oil, or insectcontrol chemi- cals which can harm rubber. = Avoid stumps, stones, deep ruts, sharp objects and other hazards that may cause tire damage. BLADE CARE For best results, mower blade must be kept sharp. Replace bent or damaged blades. TO REMOVE BLADE (See Fig. 7) Disconnect spark plug wire from spark plug and place wire where it cannot come in contact with spark plug. • Turn lawn mower on its side. Make sure air filter and carburetor are up. = Use a wood block between blade and mower housing to prevent blade from turning when removing blade bolt. = Protect your hands with gloves and/or wrap blade with heavy cloth. • Remove blade bolt by turning counter-clockwise. Use a 9/16" box or open-end wrench. , Remove blade and attaching hardware (bolt, lock washer and hardened washer). NOTE: Remove the blade adapter and check the key inside hub of blade adapter. The key must be in good condition to work properly. Replace adapter if damaged. TO REPLACE BLADE (See Fig. 7) Position the blade adapter on the engine crankshaft. Be sure key in adapter and crankshaft keyway are aligned. • Position blade on the blade adapter aligning the two (2) holes in the blade with the raised lugs on the adapter. - Be sure the trailing edge of blade (opposite sharp edge) is up toward the engine. ® Installthe blade bolt with the Iockwasher and hardened washer into blade adapter and crankshaft. • Use block of wood between blade and lawn mower housing and tighten the blade bolt, turning clockwise. • The recommended tightening torque is 35-40 ft. Ibs. IMPORTANT: BLADE BOLT IS GRADE 8 HEAT TREATED. NOTE: We do not recommend sharpening blade- but if you do, be sure the blade is balanced. TO SHARPEN BLADE Care should be taken to keep the blade balanced. An unbalanced blade will cause eventual damage to lawn mower or engine . The blade can be sharpened with a file or on a grinding wheel. Do not attempt to sharpen while on the mower. • To check blade balance, drive a nailinto a beam or wall. Leave about one inch of the straight nail exposed. Place center hole of blade over the head of the nail. If blade is balanced, it should remain in a horizontal position. If either end of the blade moves downward, sharpen the heavy end until the blade is balanced. BLADE BLADE CRANK- ADAPTER_ SHAFT KEYWAY KEY 10 rK- BL BC SHAFT HARDENED WASHER TRAILING LOCK WASHER EDGE BLADE ADAPTER FIG. 7 GEAR CASE To keep your drive system working properly, the gear case and area around the drive should be kept clean and free of trash build-up. Clean under the drive cover twice a season. • The gear case is filled with lubricant to the proper level at the factory. The only time the lubricant needs attention is if service has been performed on the gear case. , If lubricant is required, use only Texaco Starplex Pre- mium Grease, part no. 750355. Do not substitute. DRIVE WHEELS Check front drive wheels each time before you mow to be sure they move freely. The wheels not turning freely means trash, grass cuttings, etc. are in the drive wheel area and must be cleaned to free drive wheels. If necessary to clean the drive wheels, check both front wheels. - Remove hubcaps, hairpin cotters and washers. , Remove wheels from wheel adjusters. = Remove any trash or grass cuttings from inside the dust cover, pinion and/or drive wheel gear teeth. • Put wheels back in place. • If after cleaning, the drive wheels do not turn freely, contact your nearest authorized service center. GRASS CATCHER (if purchased as an accessory) , The grass catcher may be hosed with water, but must be dry when used. = Check your grass catcher often for damage or deterio- ration. Through normal use it will wear. If catcher needs replacing, replace only with a manufacturer approved replacement catcher. Give the lawn mower model number when ordering.

ENGINE LUBRICATION Use only high quality detergent oil rated with API service classification SF, SG or SH. Select the oil's SAE viscosity grade according to your expected operating temperature. SAE VISCOSITY GRADES T .3oo -20° -loo D" _o" 2o° 3o_ 40° TEMPERATURE RANGE ANTICIPATED BEFORE NEXT OIL CHANGE NOTE: Although multi-viscosity otis (5W30, 10W30 etc.) improve starting in cold weather, these multi-viscosity oils wil! result in increased oil consumption when used above 32°F. Check your engine oii level more frequently to avoid possible engine damage from running low on oil. Change the oil after every 25 hours of operation orat least once a year if the lawn mower is not used for 25 hours in one year. Check the crankcase oil level before starting the engine and after each five (5) hours of continuous use. Tighten oil plug securely each time you check the oit level. TO CHANGE ENGINE OiL (See Fig. 8) NOTE: Before tipping lawn mower to drain oil, drain fuel tank by running engine until fuel tank is empty. = Disconnect spark plug wire from spark plug and place wire where it cannot come in contact with spark plug. Be sure lawn mower is on level surface. = Oil will drain more freety when warm. Catch oil in a suitable container. • Remove bottom oil drain plug. = After oil has drained completely, replace oil drain plug and tighten securely. = Refill engine with oil. Pour slowly. Do not over fill. Fill to top of slot inside of filler hole. Reconnect spark plug wire to spark plug. \ CONTAINER FIG. 8 AIR FILTER Your engine will not run properly and may be damaged by using a dirty air filter. Replace the air filter every year, more often if you mow in very dusty, dirty conditions. Do not wash air filter. 1i , Remove the air filter by turning counterclockwise to the stop and pull away from collar. o Remove filter from inside of cover. Clean the inside of the cover and the collar to remove any dirt accumulation. Insert new filter into cover, Put air filter cover and filter into collar aligning the tab with the slot. Push in on cover and turn clockwise to tighten. COLLAR SLOT COUNTER- CLOCKWISE TO REMOVE AiR FILTER _'URN CLOCKWISE AIR FILTER COVER TO TIGHTEN FIG. 9 MUFFLER Inspect and replace corroded muffler as it could create a fire hazard and/or damage. SPARK PLUG Change your spark plug each year to make your engine start easier and run better. Set spark plug gap at .030 inch. CLEANING IMPORTANT: FOR BEST PERFORMANCE, KEEP MOWER HOUSING FREE OF BUILT-UP GRASS AND TRASH. CLEAN THE UNDERSIDE OF YOUR MOWER AFTER EACH USE. CAUTION: Disconnect spark plug wire from spark plug and place wire where it cannot come in contact with the spark plug. o Turn lawn mower on its side. Make sure air filter and carburetor are up. Clean the underside of your lawn mower by scraping to remove build-up of grass and trash. , Clean engine often to keep trash from accumulating. A clogged engine runs hotter and shortens engine life. • Keep finished surfaces and wheels free of all gasoline, oit,etc. We do not recommend using a garden hose to clean lawn mower unless the electrical system, muffler, air filter and carburetor are covered to keep water out. Water in engine can result in shortened engine life. CLEAN UNDER DRIVE COVER Clean under drive cover at least twice a season. Scrape underside of cover with putty knife or similar tool to remove any buitd-up of trash or grass on underside of drive cover.

= Make sure the blade and all moving parts have completely stopped. = Disconnect spark plug wire from spark plug and place where it cannot come in contact with plug, LAWN MOWER TO ADJUST CUTTING HEIGHT See "TO ADJUST CUTTING HEIGHT" in the Operation section of this manual. DISCHARGE GUARD The discharge guard, attached to the discharge opening of your lawn mower, is provided to prevent the possibility of injury resulting from objects being thrown out of the dis- charge opening into the operator mowing position, tf the discharge guard becomes damaged, it should be replaced. DRIVE _COVER BELT PUSH DOWN REAR DEFLECTOR The rear deflector, attached between the rear wheels of your mower, is provided to minimize the possibility that objects will be thrown out of the rear of the mower into the operator mowing position. If the deflector becomes dam- aged, it should be replaced. TO REMOVE/REPLACE DRIVE BELT (See Fig. 10) * Remove drive cover. Remove belt by pushing down on gear case pulley. , Turn lawn mower on its side with carburetor and fuel cap up. , Remove blade. , Remove debris shield. . Remove belt from engine pulley on crankshaft. , Install new belt by reversing above steps. , Always use factory approved belt to assure fit and long life. FIG. 10 12

Your lawn mower handle can be raised or lowered for your mowing comfort. Four (4) positions are available: high, medium high, medium low and low. Handles are shipped mounted in the medium low position. • To change from medium low to medium high position, the upper and lower handle sections will have to be turned over (See Fig. 11B). - Remove the cable clips. = Remove the controls and operator presence control bar from the upper handle. , Remove hairpin cotters. - Disconnect the lower handle from the handle brackets (See Fig. 13). , Turn the handle over and reassemble the hairpin cotters that have been removed. , Reassemble the controls and the operator presence control bar to the upper handle. CAUTION: The operator presence con= trol bar must pivot freely to permit blade/ brake engagement when control bar is releasedo Do not overtighten the fas. toners holding the controls to the up- per handle. , To change from medium low to high position only the upper handle section will have to be turned over (See Fig. 12A). - To change from medium low to low position, only the lower handle section will have to be turned over (See Fig. 12B). ENGINE ENGINE SPEED Your engine speed has been factory set. Do not attempt to increase engine speed or it may result in personal injury. If you believe that engine is running too fast ortoo stow, take your mower to an authorized service center for repair and adjustment. CARBURETOR Your carburetor has a non-adjustable fixed main jet for mixture control. If your engine does not operate properly due to suspected carburetor problems, take your lawn mower to an authorized service center for repair and/or adjustment. SHIPPING POSITION MEDIUM LOW MEDIUM HIGH FIG. 11A FiG. 11B LOW FIG. 12A FIG. 12B \ LOWER HANDLE SQUEEZE TO REMOVE HAIRPIN CLiP HANDLE BRACKET FiG. 13 13

end of the season or if the unit will not be used for 30 days or more. LAWN MOWER When lawn mower is to be stored for a period of time, clean it thoroughly/remove all dirt, grease, leaves, etc. Store in a clean, dry area. • Clean entire lawn mower (See "CLEANING" in the Customer Responsibilities section of this manual). • Lubricate as shown in the Customer Responsibilities section of this manual. Be sure that all nuts, bolts, screws, and pins are securely fastened. Inspect moving parts for damage, breakage and wear. Replace if necessary. , Touch up all rusted or chipped paint surfaces; sand lightly before painting. HANDLE (See Fig. 14) You can fold your lawn mower handle for storage. o Squeeze the bottom ends of the tower handle toward each other until the lower handle clears the handle bracket, then move handle forward. , Loosen upper hand!e mounting bolts enough to allow upper handle to be folded back. IMPORTANT: WHEN FOLDING THE HANDLE FOR STORAGE OR TRANSPORTATION, BE SURE TO FOLD THE HANDLE AS SHOWN OR YOU MAY DAMAGE THE CONTROL CABLES. , When setting up your handle from the storage position, the lower handle will automatically lock into the mowing position. LOWER HANDLE SQUEEZE TO FOLD j \ MOUNTmNG PIN OPERATOR PRESENCE CONTROLBAR UPPER HANDLE FOLDFORWARD FORSTORAGE FOLD BACKWARD MOWING POSITION LOWER HANDLE ENGINE FUEL SYSTEM IMPORTANT: IT IS IMPORTANT TO PREVENT GUM DEPOSITS FROM FORMING IN ESSENTIAL FUEL SYSTEM PARTS SUCH AS CARBURETOR, FUEL FILTER, FUEL HOSE, OR TANK DURING STORAGE. ALSO, EXPERIENCE INDICATES THAT ALCOHOL BLENDED FUELS (CALLED GASOHOL OR USING ETHANOL OR METHANOL) CAN ATTRACT MOISTURE WHICH LEADS TO SEPARATION AND FORMATION OF ACIDS DURING STORAGE. ACIDIC GAS CAN DAMAGE THE FUEL SYSTEM OF AN ENGINE WHILE IN STORAGE. , Drain the fuel tank. • Start the engine and let it run until the fuel lines and carburetor are empty. - Never use engine or carburetor cleaner products in the fuel tank or permanent damage may occur. - Use fresh fuel next season. NOTE: Fuel stabilizer is an acceptable alternative in minimizing the formation of fuel gum deposits during stor- age. Add stabilizer to gasoline in fuel tank or storage container. Always follow the mix ratio found on stabilizer container, Run engine at least 10 minutes after adding stabilizer to allow the stabilizer to reach the carburetor. DO not drain the gas tank and carburetor if using fuel stabilizer. ENGINE OIL Drain oil (with engine warm) and replace with clean engine oil. (See "ENGINE" in the Customer Responsibilities section of this manual). CYLINDER • Remove spark plug. • Pour one ounce (29 ml) of oil through spark plug h01e into cylinder. o Pul! starter handle slowly a few times to distribute oil. , Replace with new spark plug. OTHER , Do not store gasoline from one season to another. , Replace your gasoline can if your can starts to rust. Rust and/or dirt in your gasoline witl cause problems. - tf possible, store your unit indoors and cover it to give protection from dust and dirt. ® Cover your unit with a suitable protective cover that does not retain moisture. Do not use plastic. Plastic cannot breathe which allows condensation to form and wit! cause your unit to rust. IMPORTANT: NEVER COVER MOWER WHILE ENGINE AND EXHAUST AREAS ARE STILL WARM. _ILA ing wb-.ere fume_ay reach an open ! fl_r spakr., AHow the engine to I FIG. 14 14

Engagement Bracket Shifter Sea! Gear Case Halves Kit _Inciudes Key Nos. 4, 5, and 7) Bearing Worm Shaft Drive Shaft Hardened Washer KEY NO, !! !2 13 14 15 16 t7 I8 19 PART NO, DESCRIPTION t 3t 484 C _.._tchYoke 700343 86447 ! 37050 -4eticat Gear 75_' Clutch Jaw 75: • Grease 12000003 EoRhg 850848 Hi.-Pro Key 81585X004 Spring Bracket NOTE: All compor_ent dimensions given in U.S. inches.. I inch = 25,4 mm ....... "15

REPAIR PARTS ROTARY LAWN MOWER - MODEL NO, 917.377201 o"} 6 1 lO 10 25 . 23 24_ 46 19 69 49 48 52 52 48 62 43 \ 51 33

46 85463 Rope Guide 48 149741 Control Bar 49 63601 Handle Bolt 51 134612 Cable Clip 52 150406 Hairpin Cotter 53 851084 Handle Knob 54 850263 Lower Handle 55 851074 Handle Bracket Assembly (Left) 56 152202 Handle Bracket Assembly (Right) 57 851514 Rear Deflector 58 752118 Hex Washer Head Screw #10-24 x 1/2 62 156516 Deflector Bracket 63 85543 Discharge Guard 64 87677 Hinge Rod 68 ...... Housing Bracket Torsion Spring 69 153350X479 Hubcap 70 153282X479 Wheel Adjusting Bracket 71 63601 Spacer -- 160904 Selector Spring Selector Knob Axle Arm Assembly BeJleville Washer 7J 33072 Shoulder Bolt 7"133623 Wheel & Tire Assembly 7"133500 Ftex Nut 7_3_133300 71 33723 71 33316 DESCRIPTION Locknut 3/8-16 Danger Decal Thread Cutting Screw 5/16-18 x 3/4 Hex Locknut Debris Shield Hex Head Thread Rolling Screw 3/8-16 x 1-1/8 Hex Head Screw 3/8-24 x 1-3/8 (Grd. 8) Helical Lockwasher Hardened VVasher Blade 22" , Blade Adapter Deflector Lawn Mower Housing (Incl. Ref. #46, 59 & 60) Engine Pulley Hi-Pro Key #HP 505 Engine - (See Breakdown) Craftsman Model 143.975502 Support Brkt Handle RH Support Brkt Handle LH Locknut Keps Owner's Manual (English!Spanish) Available accessories not included with lawn mower: Grass Catcher Gas Can (2.5 gal.) Fuel Stabilizer SAE 30W Oil (20 oz.) High Wheel Kit Mower Cover

Control Head Kit Locknut 1/4-20 Hex Washer Head Screw V-Belt Spring Retainer Hex Nut Hubcap Nylon Bushing Wheel & Tire Assembly E-Ring Pinion Dust Cover Felt Washer #10-24 x 2-1/8 16 67725 18 701037 25 152903 26 143603 28 154990 31 132010 32 137052 33 48386 35 152018 36 702511 37 137090 38 STD541425 40 75192 4! 152019 55 86012 917.377201 DESCR_PTION Washer 1/2 x 1-1/2 x .134 Selector Knob Drive Cover Decal Pan Head Tapping Screw #10-24 Drive Cover Hex Flange Nut Drive Pulley Drive Control Cable Kit Wheel Adjuster Assembly (Left) Gear Case Assembly Spring • Locknut 1/4-20 Spring Wheel Adjuster Assembly (Right) Driveshaft Cover

CRAFTSMAN 4=CYCLE ENGINE MOOELNUMBER143.97SS02 4O0 130 120 126 260 261 Oj 370K 223 390 287 241 < 245 238 250 20

Dowel Pin Breather Element Breather Ass'y. (Inc!. 6 & 12A) Breather Cover & Tube (Incl. 12B) Breather Tube Elbow Washer Governor Rod (Incl. 14) Governor Lever Governor Lever Clamp Screw, Torx T-15, 8-32 x 19/64" Extension Spring Oil Seal Crankshaft Piston, Pin & Ring Set (Std,) Piston, Pin & Ring Set (.010" OS Piston, Pin & Ring Set (.020" OS Piston & Pin Ass'y. (Std.) (Incl. 43) Piston & Pin Ass'y. (.010" OS) (Incl. 43) Piston & Pin Ass'y. (.020" OS) (Incl. 43) Ring Set (Std.) Ring Set (.010" OS) Ring Set (.020" OS) Piston Pin Retaining Ring Connecting Rod Ass'y. (Incl. 46) Connecting Rod Bolt Valve Lifter Camshaft (MCR) Oil Pump Ass'y. Mounting Flange Gasket Mounting Flange (Ind. 72 thru 83) Oil Drain Plug (Incl. 73) Drain Plug Gasket Oil Seal Governor Shaft Washer Governor Gear Ass'y. (Incl. 81) Governor Spool Screw, 1/4-20 x 1-1/4" Flywheel Key Flywheel Belleville Washer Flywheel Nut Solid State Ignition Spark Plug Cover Screw, Torx T-15, 10-24 x 15/16" Ground Wire * Cylinder Head Gasket Cylinder Head Exhaust Valve (Std.) (Incl. 151) Exhaust Valve (1/32" OS) (Incl. 151) Intake Valve (Std.) (Incl. 151) Intake Valve (1/32" OS) (incl. 151) Screw, 5/16-18 x 1-1/2" Resistor Spark Plug (RJ19LM) Valve Spring Valve Spring Cap * Valve Cover Gasket Valve Cover Screw, 10-24 x 9/16" Nut & Lock Washer, 1/4-28 Screw, 1/4-28 x 7/8" * Carburetor To Intake Pipe Gasket 21 185 36544 Intake Pipe 186 34337 Governor Link 189 650839 Screw, 1/4-20 x 3/8" 191 36559 S.E. Brake Bracket (Incl. 195) 195 610973 Terminal 200 35727 Control Bracket (Incl. 202 Thru 205) 202 36482 Compression Spring 203 31342 Compression Spring 204 650549 Screw, 5-40 x 7/16" 205 650777 Screw, 6-32 x 21/32" 207 34336 Throttle Link 209 30200 Screw, 10-24 x 9/16" 215 32410 Control Knob 223 650451 Screw, 1/4-20 x 1" 224 34690A * Intake Pipe Gasket 238 650932 Screw, 10-32 x 49/64" 239 34338 * Air Cleaner Gasket 241 35797 Air Cleaner Collar 245 35066 Air Cleaner Filter 250 35065 Air Cleaner Cover 260 36915 Blower Housing 261 30200 Screw, 10-24 x 9/16" 262 650831 Screw, 1/4-20 x 1/2" 275 36473 Muffler (Incl. 277) 277 650988 Screw, 1/4-20 x 2-5/16" 285 35000A Starter Cup 287 650926 Screw, 8-32 x 21/64" 290 30705 Fuel Line 292 26460 Fuel Line Clamp 298 28763 Screw, 10-32 x 35/64" 300 36916 Fuel Tank (Incl. 292 & 301) 301 36246 Fuel Cap 305 35647 Oil Fill Tube 306 36832 * "Q"-Ring 307 35499 "O"-Ring 309 650562 Screw, 10-32 x 1/2" 310 35648 Dipstick 313 34080 Spacer 370A 36261 Lubrication Decal 370B 35167 Control Decal 370C 36861 Primer Decal 370K 36695 Starter Decal 380 632747 Carburetor (incl. !84) 390 590694 Rewind Starter 400 36481 Gasket Set (Incl. Items Marked * in Notes) 416 36085 Spark Arrestor Kit (lncl. 417)(Optional) 417 650760 Screw, 8-32 x 3/8" (Optional) 900 -- Replacement Engine NONE 900 -- Replacement S!B 750679A, order from 71-999 RPM High 2900 to 3200 RPM Low 2450 to 2750 (NOTE: This engine could have been built with 590737 starter. Refer to the design of the rope pulley strength ribs for part identification. Individual starter parts do not interchange.) incl. Part #'s 26756 (1),27234A (1), 33735 (1), 36832 (1), 34338 (1), 34690A (1), 35261 (1), 36477 (1) NOTE: All component dimensions given in U.S. inches 1 inch = 25.4 mm

"_>_-4 _._5_3_,, _ 1 631615 Throttle Shaft & Lever Assembly 2 631767 Throttle Return Spring 4 631184 Dust Seal Washer _7._Z__ 5 631183 DustSeal (Throttle) _ ._.o 6 632504 Throttle Shutter O 7 650506 Shutter Screw "" 16 631807 Fuel Fitting _j 25 631867 Float Bowl -_/ 27 631024 Float Shaft _-_ 28 632019 Float ÷.... 29 631028 Float Bowl"Q" Ring 30 631021 Inret Needle, Seat, & Clip (Incl. 31) 31 631022 Spring Clip '_ 35 36045 Primer Bulb/Retainer Ring 36 632735 Main Nozzle Tube _! 37 632547 "0" Ring, Main Nozzle Tube ,_'_..8 40 632736 High Speed Bowl Nut 44 27110 Bowl Nut Washer 48 631027 Welch Plu Atmos hericVe t KEY PART NO. NO. DESCRIPTION -- 590694 Recoil Starter 1 590599A Spring Pin (Inc!. 4) 2 590600 Washer 3 590696 Retainer - ° 4 590601 Washer 5 590697 Brake Spring '-_ _ ..... 6 590698 Starter Dog 7 590699 Dog Spring E _" _'_-' 8 590700 Pulley & Rewind Spring Ass'y. (___ 11 590695 Starter Housing Ass'y. (40 degree grommet) 12 590535 Starter Rope ( 98" X 9/64" dia.) _-, ___ 13 590701 Starter Handle ,, KEY PART NO. NO. DESCRIPTION -- 590737 Rewind Starter 3 590740 Retainer 6 590616 Starter Dog 7 590617 Dog Spring 8 590618A Pulley & Rewind Spring Ass'y 11 590687A Starter Housing Ass'y (40 degree grommet) 12 590535 Starter' Rope (Length 98" x 9/64" dia.) 13 590701 Starter Handle 14 590741 Locking Tab 22

Loss of power Poorcut-uneven Excessive vibration Starter rope hard to pull Loss of drive (Self-Propelled Mowing) Grass catcher not filling (If so equipped) _ Hard to push CAUSE 1. Dirty air filter. 2. Out of fuel. 3. Stale fuel. 4. Waterin fuel. 5. Spark plug wire is disconnected. 6. Bad spark plug. 7. Loose blade or broken blade adapter. 8. Control bar in released position g. Control bar defective CORRECTION 1. 2. 3. 4. 5, 6. 7. 8. 9. Clean!replace air filter= Fil! fuel tank. Drain tank and refill with fresh clean fuel. Drain fuel tank and carburetorand refill tank with fresh gasoline. Connect wire to plug. Replace spark plug. Tighten blade bolt or replace blade adapter. Depress control bar to handle. Replace control bar. 1. Rear of lawn mower housing/blade dragging in heavy grass. 2 Cutting too much grass. 3. Dirty air filter. 4, Buildup of grass, leaves and trash under mower. 5. Too much oil in engine. 6 WaIking speed too fa_t. 1, Worn, bent orloose blade. 2. Wheel heights uneven. 3, Low engine speed. 4. Buildup of grass, leaves, and trash under mower, 1, Worn, bent or loose blade. 2. Bent engine crankshaft. 1. Engine flywheel brake is on when control bar is released. 2. Bent engine crankshaft 3. Blade adapter broken. 4. Blade dragging in grass. 1. Drive wheels not turning with drive control engaged. 2. Belt not driving. 1. Cutting height too low, 2. Lift on blade worn off. 3. Catcher not venting air, 4, Low engine speed. 1. Grass is too high or wheel height is too low. 2. Rear of lawn mower housing/blade dragging in grass. 3. Grass catcher too full. 4. Handle height positlon not right for you. I. Set in "Higher Cut" position. 2. Set in "Higher Cut" position. 3. Clean/replace air filter. 4. Clean underside of mower housing. 5. Check oil level. 6. Cut at slower walking speed. 1. Replace blade. Tighten blade bolt. 2. Set all wheels at same height. 3. Set engine speed control in fast position. 4. Clean underside of mower housing. 1. Replace blade. Tighten blade bolt. 2. Contact an authorized service center/department. 1. Depress control bar to upper handle before pulling starter rope. 2. Contact an authorized service center/department. 3. Replace blade adapter. 4. Move lawn mower to cut grass or to hard surface to start engine. 1. Adjust or replace drive control cable, if broken. 2. Put bett on pulleys or replace belts if broken. 1, Raise cutting height. 2. Replace blade. 3. Clean grass catcher. 4. Set engine speed control in fast position, 1. Raise cutting height. 2. Raise rear of lawn mower housing one (1) setting higher. 3. Empty grass catcher. 4. Adjust handle height to suit. 23

THIS TOLL FREE NUMBER: ! o800=4-REPAIR (1-800=473o7247) FOR REPLACEMENT PARTS INFORMATION AND ORDERING, CALL THIS TOLL FREE NUMBER: 1-800=FONoPART (1=800-366=7278) CRilFTSMI:IN® 5.5 HORSEPOWER 22" EZ MULCH POWER PROPELLED ROTARY LAWN MOWER Each tawn mower has its own model number. Each en- gine has its own model number. The model number for your lawn mower will be found on a decal attached to the rear of the lawn mower housing. The model number for your engine wilt be found on the blower housing of the engine. All parts Iisted herein may be ordered from any Sears, Roebuck and Co. Service Center/Department and most Retail Stores. WHEN ORDERING REPAIR PARTS, ALWAYS GIVE THE FOLLOWING INFORMATION: * PRODUCT - LAWN MOWER o MODEL NUMBER - 917.377201 ,, ENGINE = CRAFTSMAN - MODEL NO. 14.3,975502 ', PART NUMBER , PART DESCRIPTION Your Sears merchandise has added value when you consider Sears has service units nationwide staffed with Sears trained technicians.., professional technicians specifically trained to insure that we meet our pledge to you, we service what we sell.