RSQ RW-4002U Operation & User’s Manual

◆ Product Characteristic& Specification---------------------------------------------------------------3 ◆ User’s Guide/Basic Set---------------------------------------------------------------------------------4 ◆ Important Safeguards-----------------------------------------------------------------------------------5-6 Thank you for choosing our UHF wireless microphone receiver system. Before use, please read this manual carefully to know the right operation way in order to have the best result and excitement. The receiver unit, features with quartz controlled fixed frequency VHF high band, is compatible with our wireless microphone series for dual or multi channels use. This series applies tone code squelch design to avoid interference from outside signal and noise. Sound frequency signal is mixed from both channels, then output through AF output jack. Remember to use different frequencies with no interference when assemble receivers for application of multi channels. 1

( 1) ( 2) ( 8) ( 7) ( 4) ( 5) ( 3) 1. Power Switch: push on (LED Indicator will light); push off (LED Indicator will be off). 2. Channel A Volume Control: control sound volume of CH A. 3. Channel B Volume Control: control sound volume of CH B. 4. Channel A Microphone Signal LED Indicator: when microphone is turned on, RF LED Indicator will light. It means receiving signal. 5. Channel B Microphone Signal LED Indicator: when microphone is turned on, RF LED Indicator will light. It means receiving signal. 6. Channel A Sound Signal Indicator: indicate signal from MIC A. 7. Channel B Sound Signal Indicator: indicate signal from MIC B. 8. Charger left side LED Indicator: when rechargeable battery is inserted into left side of the charge, LED indicator will light red, After the battery is fully recharged, LED becomes green and charger stops charging. (1) ( 2) ( 3) ( 4) 1. AF OUT: Output of mixed sound signal from both channels. 2. DC Power Sound Input Jack: External DC 12~15V power adapter input jack. 3. CH 1 Antenna: antenna for receiving channel A 4. CH 2 Antenna: antenna for receiving channel B

(2) Power Switch (3) Power LED Indicator Transmitter Receiver Frequency Range: VHF 170~250MHz Frequency Range: VHF 170~250MHz Power Source: DC 9V Operating Range: 50~100m(in open & line Current Consumption: 20mA of sight areas) Spurious Emission: 45dB Image and Spurious Rejection: Min 80dB Distortion: less than 0.5% Sensitivity: 10dBuV Modulation: +/-15KHz Output: unbalanced 0~0.5V Frequency Stability: +/-0.005%quartz controlled Dynamic Range: >100dB Power Output: 30mW Frequency Response: 50Hz~18KHz Hum & Noise: <0.5% Power Source: DC 12~15V, 500mA a) Power Adapter 1 PC b) Output Connector 1 PC c) Microphone 2 PCS d) User’s Guide 1 PC e) 9V Batteries 2 PCS

the other AC plug into AC power supply outlet. 2. For better receiving, extend both antennas. 3. Sound Signal Output Jack: Insert one end of the cable connector plug into the signal Output Jack at the back of the receiver (AF OUT) and the other end of the plug into KTV or amplifier MIC-IN Jack. 4. This product has to be used in a complete set. The wireless microphone is compatible only with this unit’s receiver. (Not compatible with other brand’s receiver). 5. For better performance, receiver has to be placed at least 50CM from the ground to avoid electric waves reflection. Transmitter also has to be placed at least l meter from receiver. If external antenna is used, it has to be far away from source of noise. 6. If the RF LED indicator of receiver lights when approached by the microphone, it indicates the system works normally. If the RF LED indicator dose not light, it indicates the system dose not work normally and need to be examined. 7. When microphone is on, LED indicator will flash once then go off (with power saving circuit). If LED indicator lights red, it indicates the battery has low power and need to be changed. 8. When microphone’s battery is low, LED indicator will become red. If 9V rechargeable battery is used, take it out from the microphone and insert it into the battery charger. Full recharging time is about 10 hours. (Standard battery cannot be recharged. Change with new battery ). 9. Caution: Take out battery from battery charger after full recharging in order to protect battery life. 10. Distance between receiver and microphone has big influence on the performance of microphone. During operation the nearer the distance, the better the performance. 11. Remember to turn off microphone then receiver after use to save power. 12. If microphone is not going to be used for a long period of time, take out battery to prevent damage of PCB from leaking battery. 13. The internal parts and circuit of this product have gone through adjustment by comprehensive instrument. User is not allowed to open the cover for adjustment, which may cause damage to normal function. 14. One receiver cannot receiver signal from two same-frequency microphones. If more than 2 microphones are needed, user has to use at least 2 sets of microphones and receivers with different frequencies to prevent interference. (Microphones with other brand or different frequency are not compatible with this receiver).

If water goes into this product, please turn off the power immediately and send it to after-sale service department of our company for handling. One receiver cannot receive signal from two same frequency microphones simultaneously. Other microphone with different frequency or brand cannot be used for this receiver. CAUTION During Setup and Installation To reduce the risk of electric shock, use only the specified power voltage. To prevent damage from dropping or inclining , do not put equipment on shaking, inclining etc. unstable place. To reduce the risk of fire or electric shock caused by continued use when abnormity occurs, please pull out power plug and contact our dealer when the following happens: 1.When smoke comes out from this equipment and peculiar smell can be smelt. 2.Water or other article goes into this equipment. 3.Drop on the ground and cover is damaged. 4.Power cord damaged (core comes out or cord is broken). 5.No sound output. Caution Forbidden Forbidden Forbidden Forbidden Pull Out AC Plug To prevent hurt from heavy article dropping, do not put heavy article on the top of this equipment. During Operation Caution 5