Ryobi 260111130 Owner's Operating Manual
Text of the manual
18 VOLT NICKEL-CADMIUM/
LITHIUM-ION BATTERY CHARGER
OWNER'S OPERATING MANUAL
260111130 (BCL-1800)
.
260111130 manual (SAA).indd A1
260111130 manual (SAA).indd A1
1/2/08 10:51:46 AM
1/2/08 10:51:46 AM
1. 260111130 Charger
2. Battery Port
3. Green LED
4. Red LED
5. "Key Hole" Hanger
6. Charge Indicator Light
7. Battery Gauge Button
8. Depress Latches to remove Battery Pack
DESCRIPTION (See Figures 1-3)
Fig. 1
3
4
1
2
5
Fig. 3
3
8
4
Fig. 2
7
6
260111130 manual (SAA).indd A2
260111130 manual (SAA).indd A2
1/2/08 10:51:51 AM
1/2/08 10:51:51 AM
When using the battery charger, the following
basic safety precautions should be observed for
protection against electric shock, danger of injury
and burns.
Please read and observe these instructions before using
the device.
n Before using the device check that the mains cable
and mains plug are not damaged.
n The device must not be damp, neither should it be
used in a damp environment.
n Do not use the device if it has suffered any heavy
shock or jolting, or is damaged in any other way.
n Due to the heat generated during charging,
the battery charger should not be operated on a
combustible surface/in an inflammable environment.
n Do not cover the ventilating slits
n Never disassemble the device yourself. Danger of
an electric shock or fire could be caused by improper
reassembly.
n Pull the plug of the battery charger out of the socket
when it is not in use or when cleaning it.
n Only use extension cable that is approved and
technically in perfect condition.
n During operation provide sufficient ventilation.
Malfunction during charging can be caused by storing
and operating in places where the temperature
exceeds +40°C; this should be avoided. Battery
charging in closed cupboards, near heat sources
(radiators, bright sunshine) etc. causes heat to
accumulate and can damage the device.
n If the battery is not going to be used for a longer
period, pull the battery off the battery charger and pull
out the mains plug.
n Protect battery contact to avoid a short circuit caused
by metallic object that can cause a fire or explosion!
n Do not rivet or screw any name-plates or signs onto
the device. The protective insulation can thereby
be rendered ineffective. Adhesive labels are
recommended.
n Only charge original recommended batteries.
n If the power cord is damaged, it must be replaced by an
Authorised Service Center in order to avoid a hazard.
WARNING
Do not recharge primary cells (non-
rechargeable).
Damage to property/material
Mains voltage must correspond with the voltage
specifications on the device.
n This appliance is not intended for use by persons
(including children) with reduced physical, sensory
or mental capabilities, or lack of experience and
knowledge, unless they have been given supervi-
sion or instruction concerning use of the appliance
by a person responsible for their safety. Children
should be supervised to ensure that they do not
play with the appliance.
n This appliance is not intended for use by young
children or infi rm persons unless they have been
adequately supervised by a responsible person to
ensure that they do not play with the appliance.
n Keep children and visitors away. Visitors should
wear safety glasses and be kept a safe distance from
work area. Do not let visitors contact tool or extension
cord.
n Complies with AS/NZS 60335.
ASSEMBLY
No assembly required on this product.
SPECIFICATIONS
Battery
Voltage Charger
Battery No. of cell
Pack
Input
Capacity for battery
130247015
18 V
240V, 50Hz, 1.7 Ah
15
AC only
130501002
18 V
240V, 50Hz, 2.4 Ah
10
AC only
OPERATION
WARNING
Do not allow familiarity with products to make
you careless. Remember that a careless fraction
of a second is sufficient to inflict serious injury.
260111130 manual (SAA).indd Sec1:1
260111130 manual (SAA).indd Sec1:1
1/2/08 10:51:53 AM
1/2/08 10:51:53 AM
Always wear safety goggles or safety glasses
with side shields when operating products.
Failure to do so could result in objects being
thrown into your eyes, resulting in possible
serious injury.
WARNING
Do not use any attachments or accessories
not recommended by the manufacturer of this
product. The use of attachments or accessories
not recommended can result in serious personal
injury.
APPLICATIONS
You may use this product for the following purposes:
n Charging compatible Ryobi 18 volt battery packs
CAUTION
If at any point during the charging process none
of the LEDs are lit, remove the battery pack
from the charger to avoid damaging the product.
DO NOT insert another battery. Return the
charger and battery to your nearest service
center for service or replacement.
CAUTION
Charge in a well ventilated area. Do not block
charger vents. Keep them clear to allow proper
ventilation.
BATTERY PROTECTION FEATURES
Ryobi One+ 18 V lithium-ion batteries are designed with
features that protect the lithium-ion cells and maximize
battery life.
If the tool stops during use, release the trigger to reset
and resume operation. If the tool still does not work, the
battery needs to be recharged.
BATTERY GAUGE (Fig. 2)
To display the amount of charge left in the battery, press
and hold the battery gauge button.
n If the charge indicator light glows green, the battery
pack is fully charged.
n If it glows yellow, it has a usable charge remaining but
will soon require recharging.
n If it glows red, the battery requires recharging as
indicated by the battery gauge symbols on top of the
battery.
Note: The LED charge indicator light will not work if
the battery protection feature has caused the battery
pack to stop powering the tool. When the battery pack
resets itself, the LED will again function.
LED FUNCTIONS OF CHARGER (Fig. 3-4)
CHARGER LED WILL BE ON TO INDICATE STATUS
OF CHARGER AND BATTERY PACK:
n Red LED on, Green LED off = Power to charger is on.
n Red LED flashing, Green LED off = Battery is being
tested.
n Red LED flashing, Green LED flashing = Battery is
defective.
n Red LED on, Green LED flashing = Battery is
charging.
n Red LED off, Green LED on = Battery is fully
charged.
CHARGING THE BATTERY PACK
Use only these Ryobi One+ 18 V battery packs with
this charger.
Battery packs for this tool are shipped in a low charge
condition to prevent possible problems. Therefore,
you should charge them until the green LED on the front
of the charger comes on.
Note: The charger will also charge Ryobi One+ 18 V
Ni-Cd battery packs.
CHARGING A COOL BATTERY PACK
If the charger does not charge the battery pack under
normal circumstances, return both the battery pack and
charger to your nearest Authorized Service Center for
electrical check.
n Charge the battery pack only with the charger
provided.
n Make sure the power supply is normal household
voltage, 240V, 50Hz, AC only.
n Make sure the latches on each side of the battery
pack snap into place and the battery pack is secured
in the charger before beginning operation.
n Connect the charger to the power supply.
n Place the battery pack in the charger aligning raised
rib on the battery pack with the groove in the charger.
260111130 manual (SAA).indd Sec1:2
260111130 manual (SAA).indd Sec1:2
1/2/08 10:51:55 AM
1/2/08 10:51:55 AM
n Press down on the battery pack to be sure contacts
on the battery pack engage properly with contacts in
the charger.
Note: After charging is complete, the green LED will
remain on until the battery pack is removed from the
charger or charger is disconnected from the power supply.
n The battery pack will become slightly warm to the
touch while charging. This is normal and does not
indicate a problem.
n Do not place the charger and battery pack in an area
of extreme heat or cold. They will work best at normal
room temperature.
Note: The charger and battery pack should be placed
in a location where the temperature is more than
10°C but less than 38°C.
n When batteries become fully charged, unplug the
charger from the power supply and remove the
battery pack.
n To remove the battery pack from the charger, depress
the latches on each side of the battery pack.
CHARGING A HOT BATTERY PACK
When using a tool continuously, the batteries in the
battery pack will become hot. You should let a hot battery
pack cool down for approximately 30 minutes before
attempting to recharge.
Note: This situation only occurs when continuous use
of a tool causes the batteries to become hot. It does not
occur under normal circumstances. Refer to "CHARGING
A COOL BATTERY PACK" for normal recharging of
batteries. If the charger does not charge your battery
pack under normal circumstances, return both the battery
pack and charger to your nearest Authorized Service
Center for electrical check.
LED FUNCTION
LED
INDICATOR
BATTERY
PACK
RED
LED
GREEN
LED
ACTION
Power
Without
battery
pack
ON
OFF
Ready to charge
battery pack.
Evaluate
Hot
battery
pack
Flashing
OFF
When battery pack
reaches cooled
t e m p e r a t u r e ,
charger begins fast
charge mode.
Evaluate
Cold
battery
pack
Flashing
OFF
When battery pack
reaches warmed
t e m p e r a t u r e ,
charger begins fast
charge mode.
Deeply
discharged
Flashing
OFF
C h a r g e r
p r e -
charges battery
until nomal voltage
is reached, then
begins fast charge
mode.
Defective Defective Flashing Flashing B a t t e r y
p a c k
o r c h a r g e r i s
defective.
If defective, try to repeat the conditions a second
time by removing and reinstalling the battery pack. If
the LED status repeats a second time, try charging a
different battery.
If a different battery charges normally, dispose of the
defective pack (see Maintenance section).
If a different battery also indicates "Defective," the
charger may be defective.
Charging
Fast
charging
ON
Flashing
Fast charging is
complete; charger
maintains charge
mode.
Full
OFF
ON
_
_
Evaluate
260111130 manual (SAA).indd Sec1:3
260111130 manual (SAA).indd Sec1:3
1/2/08 10:51:56 AM
1/2/08 10:51:56 AM
MAINTENANCE AND REPAIRS
Risk of injury
Service, testing and repairs should only be
carried out by authorised service centres.
We recommend our customer service department or
authorised service centres.
STORAGE
Store your charger in a cool dry place between 10 &
25°C. It is not recommended to leave it in a cold works
van overnight. Ensure no metal filings or swarf can fall
into the vents during storage, as this may cause serious
injury when it is next used.
260111130 manual (SAA).indd Sec1:4
260111130 manual (SAA).indd Sec1:4
1/2/08 10:51:57 AM
1/2/08 10:51:57 AM
!".
#ONTACT DURING NORMAL BUSINESS HOURS
!5#+,!.$ #LEMOW $RIVE -T 7ELLINGTON .:
#ONTACT DURING NORMAL BUSINESS HOURS
!,, !5342!,)!. %.15)2)%3 4%,
7%34 !5342!,)!. %.15)2)%3 4%, !
0URCHASED &ROM
DDRESS /F $EALER
0RESENT 4HIS &ORM 7ITH 9OUR 0URCHASE $OCKET 7HEN 'UARANTEE 3ERVICE )S 2EQUIRED
4EL
&AX
WWWRYOBICOMAU
4EL
&REE #ALL
&AX
WWWRYOBICONZ
&OR YOUR RECORD AND TO ASSIST IN ESTABLISHING DATE OF PURCHASE NECESSARY FOR IN
GUARANTEE SERVICE
PLEASE KEEP YOUR PURCHASE DOCKET AND THIS FORM COMPLETED WITH THE FOLLOWING PARTICULARS
4HIS 'UARANTEE &ORM 3HOULD "E 2ETAINED "Y 4HE #USTOMER !T !LL 4IMES
$ATE
-ODEL .O
3ERIAL .O
39$.%9 "UILDING " 2OSEHILL )NDUSTRIAL %STATE
3HIRLEY 3TREET 2OSEHILL .37
4%#(42/.)# ).$5342)%3 !5342!,)! 049 ,)-)4%$
4%#(42/.)# ).$5342)%3 .: ,)-)4%$
3UBJECT TO THE GUARANTEE CONDITION BELOW THIS 2YOBI TOOL HEREINAFTER CALLED hTHE PRODUCTv IS GUARANTEED BY 4%#(42/.)# ).$5342)%3 !5342!,)! 049 ,)-)4%$ HEREINAFTER CALLED hTHE #OMPANYv TO BE FREE FROM DEFECTS IN MATERIAL OR WORKMANSHIP FOR A PERIOD OF MONTHS FROM THE DATE OF ORIGINAL PURCHASE COVERING BOTH PARTS AND LABOUR 5NDER THE TERMS OF THIS GUARAN
TEE THE REPAIR OR REPLACEMENT OF ANY PART SHALL BE THE OPINION OF THE #OMPANY OR ITS AUTHORISED 3ERVICE CENTRE 3HOULD SERVICE BECOME NECESSARY DURING THE WARRANTY PERIOD THE OWNER SHOULD CONTACT THE CUSTOMER SERVICE (%,0,).% OR CONTACT THE RETAILER FROM WHOM THE PRODUCT WAS PURCHASED
)N ORDER TO OBTAIN GUARANTEE SERVICE THE OWNER MUST PRESENT THE SALES DOCKET AND 'UARANTEE #ERTIFICATE TO CONFIRM DATE OF PURCHASE 4HIS PRODUCT IS SOLD BY THE DEALER OR 3ERVICE CENTRE AS PRINCIPAL AND THE DEALER HAS NO AUTHORITY FROM THE #OMPANY TO GIVE ANY ADDITIONAL GUARANTEE ON THE #OMPANYS BEHALF EXCEPT AS HEREIN CONTAINED OR HEREIN REFERRED TO 'UARANTEE #ONDITIONS
4HIS GUARANTEE ONLY APPLIES PROVIDED THAT THE 0RODUCT HAS BEEN USED IN ACCORDANCE WITH THE MANUFACTURERS RECOMMENDATIONS UNDER NORMAL USE AND REASONABLE CARE IN THE OPINION OF THE #OMPANY AND SUCH GUARAN
TEE DOES NOT COVER DAMAGE MALFUNCTION OR FAILURE RESULTING FROM MISUSE NEGLECT ABUSE OR USED FOR A PURPOSE FOR WHICH IT WAS NOT DESIGNED OR IS NOT SUITED AND NO REPAIRS ALTERATIONS OR MODIFICATIONS HAVE BEEN ATTEMPTED BY OTHER THAN AN !UTHORISED 3ERVICE CENTRE 4HIS GUARANTEE WILL NOT APPLY IF THE TOOL IS DAMAGED BY ACCIDENT OR IF REPAIRS ARISE FROM NORMAL WEAR AND TEAR 4HE #OMPANY ACCEPTS NO ADDITIONAL LIABILITY PURSUANT TO THIS GUARANTEE FOR THE COSTS OF TRAVELLING OR TRANSPOR
TATION OF THE 0RODUCT OR PARTS TO AND FROM THE SERVICE DEALER OR 3ERVICE CENTRE
SUCH COSTS ARE NOT INCLUDED IN THIS GUARANTEE
#ERTAIN LEGISLATION INCLUDING THE 4RADE 0RACTICES !CT AS AMENDED AND OTHER STATE AND TERRITORIAL LAWS GIVE RIGHTS TO THE BUYER AND IMPOSE LIABILITY ON THE SELLER IN CERTAIN CIRCUMSTANCES .OTHING HEREIN SHALL HAVE THE EFFECT OF EXCLUDING RESTRICTING OR MODIFYING ANY CONDITION GUARANTEE RIGHT OR LIABILITY IMPOSED TO THE EXTENT ONLY THAT SUCH EXCLUSION RESTRICTION OR MODIFICATION WOULD RENDER ANY TERM HEREIN VOID
260111130 manual (SAA).indd Sec1:5
260111130 manual (SAA).indd Sec1:5
1/2/08 10:51:58 AM
1/2/08 10:51:58 AM