Shindaiwa AHS242 Owner's/operator's Manual

WARNING! Always wear eye and ear protection when operating this machine! To minimize the risk of injury to yourself and others, read this manual and familiarize yourself with its contents. X7502801103 01/13

Hedge Trimmer is designed and built to deliver superior performance and reliability without compromise to qual- ity, comfort, safety or durability. Shindaiwa's engines represent the leading edge of high-performance, engine technology, delivering excep- tionally high power with remarkably low displacement and weight. As an owner/operator, you'll soon discover for yourself why Shindaiwa is simply in a class by itself! IMPORTANT! The information contained in these instructions describes machines avail- able at the time of publication. Echo Inc. reserves the right to make changes to products without prior notice, and without obligation to make alterations to units previously manufac- tured. WARNING! The engine exhaust from this product contains chemicals known to the State of California to cause can- cer, birth defects or other reproduc- tive harm. Safety .............................................3 Product Description.........................6 Specifications..................................7 Emission Control.............................7 Assembly.........................................8 Mixing fuel..................................... 11 Filling the fuel tank........................12 Starting the Engine .......................12 Stopping the Engine......................14 Checking Unit Condition................14 Safe Operation..............................15 Maintenance..................................16 Long Term Storage........................20 Troubleshooting Guide..................21 Warranty Statement.......................24 PAGE PAGE Throughout this manual are special “attention statements”. Attention Statements WARNING! A statement preceded by the triangular attention symbol and the word “WARNING” contains information that should be acted upon to prevent serious bodily injury. CAUTION! A statement preceded by the word “CAUTION” contains information that should be acted upon to prevent mechanical damage. IMPORTANT! A statement preceded by the word “IMPORTANT” is one that possesses special significance. NOTE: A statement preceded by the word “NOTE” contains information that is handy to know and may make your job easier. DANGER! A statement preceded by the triangular atten- tion symbol and the word “DANGER” contains informa- tion that should be acted upon to prevent serious injury or death. IMPORTANT! The procedures described in this manual are intended to help you get the most from your unit as well as to protect you and others from harm. These procedures are guidelines for safe operation under most conditions, and are not intended to replace any safety rules and/or laws that may be in force in your area. If you have questions regarding your power tool, or if you do not understand something in this manual, your Shindaiwa dealer will be glad to assist you. You may also contact Shindaiwa at the address printed on the back of this Manual.

make sure anyone using the trimmer does likewise. Failure to do so could result in serious personal injury or machine failure. Keep this manual for future reference. Safety tip shoes or boots with non-slip sole should be worn. Keep bystanders at least 50 feet (15 meters) away from the operating trimmer to reduce the risk of being cut by the cutting blades or struck by falling objects or thrown debris. Safety and Operational Labels This product conducts elec- tricity. Keep the product and/ or operator a minimum dis- tance of 33 feet (10 meters) away from electrical sources and power lines. Be aware of the danger of falling debris. 33 ft 10 M Always wear a hard hat to reduce the risk of head inju- ries during operation of this machine. In addition, always wear eye and hearing protec- tion. Shindaiwa recommends wearing a face shield as addi- tional face and eye protection. Wear non-slip heavy-duty gloves. The blades / cutting attach- ments are SHARP! Handle with care. An articulated hedge trimmer has the potential to cause serious personal injury to the operator or bystanders if mis- used, abused or mishandled. You must observe all special safety instructions to reduce the risk of personal injury. WARNING ! Surface can be hot. Always wear gloves when handling this unit. DANGER! THE ARTICULATED HEDGE TRIMMER IS NOT INSULATED AGAINST ELECTRICAL SHOCK! Approaching or contacting electrical lines with the trimmer could cause death or serious injury. Keep the trimmer at least 10 meters away from electrical lines or branches that contact electrical lines. Safety An articulated hedge trimmer has the potential to cause seri- ous personal injury to the operator or bystanders if misused, abused or mishandled. To reduce the risk of injury, you must maintain control at all times, and observe all safety precau- tions during operation. Never permit a person without training or instruction to operate this hedge trimmer! WARNING! Do not make unauthorized modifications or alterations to your articulated hedge trimmer or its components. Never operate this tool or any other power equipment if you are tired, ill, or under the influ- ence of alcohol, drugs, or any substance that could affect your ability or judgement. WARNING! WARNING! The ignition components of this machine generate an electromagnetic field during operation which may interfere with some pacemakers.  To reduce the risk of serious or fatal injury, persons with pacemakers should consult with their physician and the pacemaker manufacturer before operating this machine.   In the absence of such information, ECHO does not recommend the use of ECHO products by anyone who has a pacemaker.

from all openings. • ALWAYS stop engine, disconnect spark plug, and make sure all moving parts have come to a complete stop before removing obstructions, clearing debris, or servicing unit. • DO NOT start or operate unit unless all guards and protective covers are properly assembled to unit. • NEVER reach into any opening while the engine is running. Moving parts may not be visible through openings. Operating Precautions WARNING! ■ ■Never transport the articulated hedge trimmer or leave it unat- tended with the engine running. An engine that’s running could be accidently accelerated causing the blades to oscillate. ■ ■Make sure that the blade cover is in place when transporting or storing the articulated hedge trimmer. ■ ■Always make sure that the cut- ter attachment and all handles and guards are properly installed and firmly tightened before operation. ■ ■Inspect for broken, missing or improperly installed parts or attachments. ■ ■Never use a cracked or warped cut- ter or cutter bar: replace it with a serviceable one and make sure it fits properly. ■ ■Make sure there are no missing or loose fasteners, and that the stop switch and throttle controls are work- ing properly. ■ ■Never adjust blades when the engine is operating. ■ ■Make sure there is always good ventilation when operating the artic- ulated hedge trimmer. Fumes from engine exhaust can cause seri- ous injury or death. Never run the engine indoors! ■ ■Never smoke or light fires near the hedge trimmer. Keep the unit away from excessive heat. Engine fuel is very flammable and fire could lead to serious personal injury or prop- erty damage. ■ ■Make sure the cutters are cor- rectly adjusted before operating the articulated hedge trimmer (see the section ”Cutter Blade Adjustment” for cutter adjustment procedures). Never attempt cutter adjustment with the engine running! ■ ■Before starting the engine, make sure the cutter is not contacting anything. ■ ■Always confirm safe operation when using the machine. ■ ■Immediately stop the engine with the stop switch if the machine sud- denly begins to vibrate or shake. ■ ■Always stop the engine imme- diately and check for damage if you strike a foreign object or if the machine becomes tangled. Do not operate with broken or damaged equipment. ■ ■When cutting a branch that is under tension, be alert for spring- back so that you will not be struck by the moving branch. ■ ■If a cutter should bind fast in a cut, shut off the engine immediately. Push the branch or tree to ease the bind and free the cutter. ■ ■Always stop the engine and allow it to cool before refueling. Avoid overfilling and wipe off any fuel that may have spilled. ■ ■To reduce fire hazard, keep the engine and muffler free of debris, leaves, or excessive grease. ■ ■Keep a Solid Stance. Maintain footing and balance at all times. Do not stand on slippery, uneven or unstable surfaces. Do not work in odd positions or on ladders. Do not over reach. WARNING! Hedge Clipper blades are very sharp. Touching them may lead to severe personal injury. Avoid touching blades whenever possible, and always wear gloves to protect hands

Information Labels: Make sure all informa- tion labels are undamaged and readable. Immediately replace damaged or missing information labels. New labels are available from your local authorized Shindaiwa dealer. Safety Equipment and Labels Cutter Blade Cover Handle Shaft Safety Label Throttle Interlock Stop Switch Safety (continued) CAUTION! ■ ■Always maintain the articu- lated hedge trimmer according to this owner’s manual and fol- low the recommended scheduled maintenance. ■ ■Never modify or disable any of the hedge trimmer’s safety devices. Doing so may cause damage and lead to personal injury. ■ ■Always use genuine Shindaiwa parts and accessories when repair- ing or maintaining this machine. ■ ■Do not make unauthorized modi- fications to the articulated hedge trimmer or its components. ■ ■Keep the cutters sharp and prop- erly adjusted. ■ ■Never allow the engine to run at high speed without a load. Doing so could damage the engine. ■ ■When transporting the hedge trimmer in a vehicle, tie it down securely to prevent fuel spillage or damage to the machine. ■ ■Always stop the engine and allow it to cool before refueling. Avoid overfilling and wipe off any fuel that may have spilled. ■ ■Never place flammable material close to the engine muffler and never run the engine without the spark arrestor screen in place. ■ ■Always clear your work area of trash or hidden debris to help ensure good footing. ■ ■Keep the articulated hedge trim- mer as clean as possible. Keep it free of loose vegetation, mud, etc.

15 meters away from the operating trimmer to reduce the risk of being struck by falling objects or thrown debris. Always operate with both hands firmly gripping the machine. Always wear a hard hat to reduce the risk of head injuries during operation of this machine. Always wear eye and hearing protection. Shindaiwa recommends wearing a face shield as additional face and eye protection. Keep a proper footing and do not overreach— maintain your balance at all times during operation. This machine is designed for trimming hedges. Do not use this machine for other purposes. NEVER allow children to use the unit. Avoid operating near bystanders or when children are nearby. ALWAYS wear close-fitting clothing. Gloves offer added proctection and are strongly recommended. Do not wear clothing or jewelry that could get caught in machinery. ALWAYS protect yourself from hazards such as thorny brush and flying debris by wearing gloves and close fitting clothing that covers arms and legs. Never wear shorts. Don't wear loose clothing or items such as jewelry that could get caught in machinery or underbrush. Secure long hair so it is above shoulder level. ALWAYS clear your work area of trash or hidden debris that could be thrown back at you or toward a bystander. ALWAYS be aware of your surroundings and alert to any danger that you may not hear due to machine noise. Product Description Using the illustration as a guide, familiarize yourself with the Shindaiwa AHS242 articulated hedge trimmer and its various components. Understanding your machine helps ensure top perfor- mance, longer service life, and safer operation. Handle Grip Outer Tube Hedge Trimmer Cutter Assembly Cutter Assembly Adjustment Lever Cutter Blade Cover Fuel Tank Guard Handle Gearcase Hedge Trimmer Cutter Assembly Cutter Bar and Cutter Blades Latch Release Latch Lock Ignition Air Filter Assembly Spark Plug Powerhead Assembly Fuel Tank Guard ThrottleTrigger Fuel Tank Wear sturdy footwear with nonslip soles to provide good footing. Steel-toed safety boots are recommended. Never operate machine bare-footed.

Model AHS242 Engine type 2-stroke, single cylinder, air cooled, gasoline engine Dimensions (L x W x H) 1682 mm (66.2 in) x 248 mm (9.76 in) x 245 mm (9.6 in) Weight 5.99 Kg (13.2 lb) Bore x stroke 33 x 28 mm/1.3 x 1.1 in. Displacement 23.9 cm3/1.46 cu. in. Fuel/oil ratio 50:1 with *ISO-L-EGD or JASO FD class engine oil Carburetor type Diaphragm-type Fuel tank capacity .69 L / 23.3 oz. Ignition One-piece electronic, C.D.I. Spark plug NGK BPMR8Y Electrode Gap 0.6 mm/ .024 in. Torque 150-170 kgf cm / 130 - 150 in • lbf Air cleaner type Non-reversible double layer felt Starting method Recoil Stopping method Slide switch Transmission type Automatic, centrifugal clutch w/bevel gear Cooling System Forced Air Blade Length 568 mm/22.4 in. Cutter Drive Spur Gear Gear Lubricant Lithium Based Grease Idle Speed 3,000 RPM Clutch Engagement Speed 4,000 RPM Wide Open Throttle Speed (W.O.T.) 11,800 RPM An Emission Control Label is located on the engine. (This is an EXAMPLE ONLY, information on label varies by en- gine FAMILY). PRODUCT EMISSION DURABILITY (EMISSION COMPLIANCE PERIOD) The 50 or 300 hour emission compliance period is the time span selected by the manufacturer certifying the engine emissions output meets applicable emissions regulations, provided that approved maintenance proce- dures are followed as listed in the Maintenance Section of this manual. Emission Control (Exhaust & Evaporative) EPA 2010 and Later The emission control system for the engine is EM (engine modification) and, if the second to last character of the En- gine Family on the Emission Control Information label (sample below) is “C”, “K”, or “T”, the emission control system is EM and TWC (3-way catalyst). The fuel tank/fuel line emission control system is EVAP (evaporative emissions). Evaporative emissions for California models are only applicable to fuel tanks. IMPORTANT! This spark ignition system complies with the Canadian standard ICES-002.

ting, or when cutting thick and/or dense branches, efficiency may be increased by trimming without the blade guard. Assembly IMPORTANT! The terms “left”, “left-hand”, and “LH”; “right”, “right-hand”, and “RH”; “front” and “rear” refer to directions as viewed by the operator during normal opera- tion. A Blade Guard Removal 1. Move stop switch to stop position. 2. Disconnect spark plug wire. WARNING! Hedge Clipper blades are very sharp. Touching them may lead to severe personal injury. Avoid touching blades whenever possible, and always wear gloves to protect hands. Blade Guard Removal/Install B Install Blade Guard 1. Move stop switch to stop position. 2. Disconnect spark plug wire. WARNING Hedge clipper blades are very sharp. Touching them may lead to severe personal injury. Use a socket and extension when removing locknuts in order to keep hands at a safe distance from sharp blades. 3. Remove (4) locknuts (B). 4. Install blade guard. 5. Secure blade guard with four (4) locknuts. 6. Adjust blades. See “Cutter blade adjustment” section. WARNING! Hedge clipper blades are very sharp. Touching them may lead to severe personal injury. Use a socket and extension when removing locknuts in order to keep hands at a safe distance from sharp blades. 3. Remove four (4) blade guard locknuts (A). 4. Remove blade guard. 5. Install (4) locknuts. NOTE: Use new locknuts every time blade guard is installed or removed. 6. Adjust blades. See “Cutter blade adjustment” section. IMPORTANT! If blade guard is damaged or show signs of wear, replace it. NOTE: Use new locknuts every time blade guard is installed or removed. This unit comes completely assembled. Before using this product, please make sure you have all the components required for a complete unit. Carefully inspect all components for damage. ■ ■Operator’s Manual ■ ■Unit assembly w/blade stiffener ■ ■Assembly Tool (s) ■ ■Blade cover ■ ■Emission Control Warranty Statement

WARNING! WARNING! Never run the engine when adjusting the cutter assembly. Latch Release Grasp the outer tube near the handle Adjustment Lever Adjustment Lever Pivot the cutter assembly using the adjustment lever... Press the latch lock Make sure the latch lock and the latch release return securely to the locked position Latch Lock Latch Lock ■ ■The cutter blades are very sharp. Do not grasp the blades with your hands. Always use gloves when working near the cutter assembly. ■ ■Do not allow the blades to con- tact your body. ■ ■Do not touch the cutter blades when the engine is running. The blades can oscillate even if the engine is idling. 1. Position the hedge trimmer on a flat, level surface. 2. With your right hand, grasp the outer tube near the handle. With your left hand, grip the adjustment lever on the cutter assembly. IMPORTANT! The latch lock provides an interlock to help prevent inadvertent depression of the latch release. 3. With the index finger of your left hand, press the latch lock. With your left thumb, press the latch release. 4. While holding the latch release down, pivot the cutter assembly away from you using the adjustment lever until it is at the desired cutting angle. 5. Release the latch lock and the latch release. Make sure the latch lock and the latch release return securely to the locked position. 6. Remove the cover from the cut- ter blade. The engine now may be started (refer to the section ”Starting the Engine”.) Position the handle on the outer tube as shown Handle This unit comes with the handle in- stalled. It can be re-adjusted for opera- tor comfort in the following manner. 1. Loosen the four socket-head cap- screws. 2. Rotate/slide handle assembly to best position for operator comfort, usually 25 cm (10 in.) ahead of the throttle assembly. 3. Tighten socket-head capscrews in a crisscross manner. Assembly (continued)

to 10 different positions ranging from 90° to 225° from the outer tube as shown. NOTE: This articulated hedge trimmer is equipped with a travel limiter that pre- vents the cutter assembly from rotating outside of the 90°- 225° range. The travel limiter prevents the cutter assembly from rotating outside of the 90°- 225° range The cutter assembly can be adjusted to 10 different positions Travel limiter and adjustment range WARNING! Always make sure the latch lock is securely locked after each adjustment. 225° 135° 90° Adjusting cutter assembly for storage or transportation 1. With the engine off, install the blade cover onto the blade. 2. Using the procedures described above, rotate the cutter assem- bly so it is parallel to the tube. Make sure the latch lock and the latch release return securely to a locking position. WARNING! Never run the engine when adjusting the cutter assembly. Make sure the blade cover is in place before storing or transporting Transport / storage position 3. Make sure the blade cover is in place on the blade before storing or trans- porting. Cable Adjuster Rotate cable adjuster in or out to obtrain proper free play Lock Nut 4 - 6 mm Throttle lever free play The throttle lever free play should be approximately 4 - 6 mm. Make sure that the throttle lever operates smoothly without binding. If it becomes necessary to adjust the lever free play, follow the procedures and illustrations that follow. 1. Loosen the air cleaner cover knob(s) and remove the air cleaner cover. 2. Loosen the lock nut on the cable adjuster. Turn the cable adjuster in or out as required to obtain proper free play 4 - 6 mm. 3. Tighten the locknut. 4. Reinstall the air cleaner cover. Throttle lever free play Assembly (continued)

requirements are NOT approved for use in Shindaiwa gasoline engines. Use of alternative fuels may cause performance problems, loss of power, overheating, fuel vapor lock, and unintended machine operation, including, but not limited to, improper clutch engagement. Alternative fuels may also cause premature deterioration of fuel lines, gaskets, carburetors and other engine components. Fuel Requirements Gasoline - Use 89 Octane [R+M/2] (mid grade or higher) gasoline known to be good quality. Gasoline may contain up to 10% Ethanol (grain alcohol) or 15% MTBE (methyl tertiary-butyl ether). Gasoline containing methanol (wood alcohol) is NOT approved. 2 Stroke Mixture Oil - A 2-stroke engine oil meeting ISO-L-EGD (ISO/CD 13738) and J.A.S.O. M345/FD standards must be used. Shindaiwa OneTM 2-Stroke Oil is strongly recommended as it meets this standard and is specifically formulated for use in all Shindaiwa 2-stroke engines. Engine problems due to inadequate lubrication caused by fail- ure to use an ISO-L-EGD (ISO/CD 13738) and J.A.S.O. M345/FD certified oil will void the engine warranty. Mixing Fuel For increased engine protection, Shindaiwa recommends using Shindaiwa Red ArmorTM engine oil to protect the engine from harmful carbon build up, maintain engine performance, and increase engine life. Shindaiwa Red ArmorTM engine oil exceeds ISO-L-EGD and J.A.S.O. M345/FD performance requirements. Examples of 50:1 mixing quantities IMPORTANT! Shindaiwa OneTM 2-Stroke oil or Red ArmorTM engine oil may be mixed at 50:1 ratio for application in all Shindaiwa engines sold in the past, regardless of ratio specified in those manuals. IMPORTANT! Stored fuel ages. Do not mix more fuel than you expect to use in thirty (30) days, ninety (90) days when a fuel stabilizer is added. Use of unmixed, improp- erly mixed, or stale fuel, may cause hard starting, poor performance, or severe engine damage and void the product warranty. Read and follow instructions in the Long Term Storage section of this manual. Handling Fuel DANGER! Fuel is VERY flammable. Use extreme care when mixing, storing or handling or serious personal injury may result. • Use an approved fuel container. • DO NOT smoke near fuel. • DO NOT allow flames or sparks near fuel. • Fuel tanks/cans may be under pressure. Always loosen fuel caps slowly allowing pressure to equalize. • NEVER refuel a unit when the engine is HOT or RUNNING! • DO NOT fill fuel tanks indoors. ALWAYS fill fuel tanks outdoors over bare ground. • DO NOT overfill fuel tank. Wipe up spills immediately. • Securely tighten fuel tank cap and close fuel container after refueling. • Inspect for fuel leakage. If fuel leakage is found, do not start or operate unit until leakage is repaired. • Move at least 3m (10 ft.) from refueling location before starting the engine.

occur. Return unused fuel to an approved fuel stor- age container. Storage - Fuel storage laws vary by locality. Contact your local government for the laws affecting your area. As a precaution, store fuel in an approved, airtight container. Store in a well-ventilated, unoccupied build- ing, away from sparks and flames. IMPORTANT! Stored fuel may separate. ALWAYS shake fuel con- tainer thoroughly before each use. Mixing Instructions 1. Fill an approved fuel container with half of the required amount of gasoline. 2. Add the proper amount of engine oil to gasoline. 3. Close container and shake to mix oil with gaso- line. 4. Add remaining gasoline, close fuel container, and remix. IMPORTANT! Spilled fuel is a leading cause of hydrocarbon emissions. Some states may require the use of automatic fuel shut- off containers to reduce fuel spillage. 1. Place the unit on a flat, level sur- face. 2. Clear any dirt or other debris from around the fuel filler cap. Filling the Fuel Tank CAUTION! Slowly remove the fuel cap only after stopping the engine. WARNING! Minimize the Risk of Fire ■ ■NEVER smoke or light fires near the engine. ■ ■ALWAYS stop the engine and allow it to cool before refueling. ■ ■ALWAYS Wipe all spilled fuel and move at least 3 meters (10 feet) from the fueling point and source before starting. ■ ■NEVER place flammable material close to the engine muffler. ■ ■NEVER operate the engine without the muffler and spark arrester screen in place and in good working condition. ■ ■FUEL IS HIGHLY FLAMMABLE. ■ ■ALWAYS store gasoline in a container approved for flammable liquids. ■ ■ALWAYS inspect the unit for fuel leaks before each use. During each refill, check that no fuel leaks from around the fuel cap and/or fuel tank. If fuel leaks are evident, stop using the unit immediately. Fuel leaks must be repaired before using the unit. ■ ■ALWAYS move the unit at least 3 meters (10 feet) away from a fuel storage area or other readily flam- mable materials before starting the engine. 3. Remove the fuel cap, and fill the tank with clean, fresh fuel. 4. Reinstall the fuel filler cap and tighten firmly. 5. Wipe away any spilled fuel before starting engine. Starting the Engine IMPORTANT! Engine ignition is controlled by a two position switch mounted on the throttle housing labeled, “I” for ON or START and “O” for OFF or STOP. NOTE: The blade cover is used for transportation and storage. Remove blade cover before using the unit. WARNING! Never start the engine from the operating position.

late) when the engine is started. Keep away from the cutter assem- bly while starting the engine! IMPORTANT! The primer system only pushes fuel through the carburetor. Repeatedly pressing the primer bulb will not flood the engine with fuel. CAUTION! Do not pull the recoil starter to the end of the rope travel. Pulling the recoil starter to the end of the rope travel can damage the starter. 1. Slide the ignition switch to the “ON” position. 2. Press the primer bulb until fuel can be seen flowing in the transparent return tube. 3. Set the choke lever to the CLOSED position if engine is cold. 4. While holding the outer tube firmly with left hand. Use your other hand to slowly pull the recoil starter handle until resistance is felt, then pull quickly to start the engine. Primer Bulb Press the primer bulb Closed Set the choke lever to CLOSED Move choke lever to OPEN position when engine starts Open ...and pull recoil starter handle upward Slide the ignition switch to the “ON” position ON 5. When the engine starts, slowly move the choke lever to the ”OPEN” position. (If the engine stops after the initial start, close the choke and restart.) Starting the Engine (continued) IMPORTANT! If the engine fails to start after several attempts with the choke in the closed position, the engine may be flooded with fuel. If flooding is suspected, refer to the ”Starting a Flooded Engine” section of this manual. Return Tube When the Engine Starts... ■ ■After the engine starts, allow the engine to warm up at idle 2 or 3 minutes before operating the unit. ■ ■If the engine does not continue to run, repeat the appropriate crank- ing procedures for a cold or warm engine.When the engine starts, clear excess fuel from the combus- tion chamber by accelerating the engine several times with the throt- tle lever. ■ ■Advancing the throttle makes the cut- ting attachment move faster; releasing the throttle permits the attachment to stop moving. If the cutting attachment continues to move when the engine returns to idle, carburetor idle speed should be adjusted (see “Adjusting Engine Idle”.). If the engine does not start ■ ■Repeat the appropriate starting pro- cedure for a cold or warm engine. ■ ■If the engine still fails to start, use the procedures for “Starting a flooded engine.”

1. Slide the ignition switch to the “I” (ON) position. 2. Open the choke, put the throttle lever in the full throttle position, then clear excess fuel from the combustion chamber by cranking the engine several times. 3. If the engine still fails to start or fire, refer to the troubleshooting flow chart at the end of this manual. Starting the Engine (continued) Slide ignition switch to OFF OFF Idle the engine briefly before stopping (about 2 minutes), then slide the ignition switch to the “O” (Engine OFF) position. Stopping the Engine WARNING! The cutting attachment can continue moving after the engine is stopped! Checking Unit Condition ALWAYS make sure the cutting attach- ment fits properly into the appropriate attachment holder. If a properly in- stalled attachment vibrates, replace the attachment with new one and re-check. ALWAYS stop the engine immediately and check for damage if you strike a for- eign object or if the unit becomes tangled. Do not operate with broken or damaged equipment. NEVER allow the engine to run at high speeds without a load. Doing so could damage the engine. NEVER operate a unit with worn or damaged fasteners or attachment holders. NEVER operate the unit with the pro- tective devices removed! Use only authorized Shindaiwa parts and accessories with your Shindaiwa hedge trimmer. Do not make modifica- tions to this unit without written approv- al from Shindaiwa. ALWAYS make sure the cutting attach- ment is properly installed and firmly tightened before operation. NEVER use a cracked or warped cutting attachment: replace it with a serviceable one. WARNING! A cutting attachment shield or other protective device is no guarantee of protection against rico- chet. YOU MUST ALWAYS GUARD AGAINST FLYING DEBRIS! Safe Operation This machine is designed especially for trimming hedges. Never use this machine for any other purposes. Never try to cut stones, met- als, plastics or any other hard objects. Using this Articulated Hedgetrimmer for other purposes than trimming hedges may damage the machine or cause serious injury. Before trimming: ■ ■Wear suitable protective clothing and equipment. See the “Safety” section for information. ■ ■Choose the best working position for safety against the falling objects (branches, etc.). ■ ■Never stand directly underneath the branch you are cutting. Be aware of falling branches. Note that a branch may spring back at you after it hits the ground. WARNING! Moving parts can amputate fingers or cause severe injuries. Keep hands, clothing and loose objects away from all openings. Always stop engine, disconnect spark plug, and make sure all moving parts have come to a complete stop before removing obstructions, clearing debris, or servicing unit. WARNING! Engine exhaust IS HOT, and contains Carbon Monoxide (CO), a poison gas. Breathing CO can cause uncon- sciousness, serious injury, or death. Exhaust can cause serious burns. ALWAYS position unit so that exhaust is directed away from your face and body. WARNING! Operation of this equipment may create sparks that can start fires. This unit is equipped with a spark arrestor to prevent discharge of hot particles from the engine. Metal blade use also can create sparks if the blade strikes rocks, metal, or other hard objects. Contact local fire authorities for laws or regulations regarding fire prevention requirements.

Working Position ■ ■Hold the shaft grip above the powerhead with your right hand, and the loop handle with your left hand. ■ ■Your left arm should be extended to the most comfortable position. Operator in working position Right hand on shaft grip Hold the loop handle with your left hand Preparations Use power pruner attachment to cut out thick branches first. Cutting Sequence If a radial cut is necessary, cut a little at a time in several passes. Vertical Cut: Swing the blade up and down in an arc as you move along the hedge. Use both sides of the cutting blade. Cut without standing directly next to the hedge, e.g. with a flower bed between operator and hedge. Overhead Cut: Hold the shaft upright with a 90° blade angle to cut an upper surface of a hedge. Horizontal Cut: Hold the cutting blade at an angle of 0° to 10° as you swing the hedge trimmer horizontally. Swing the blade in an arc towards the outside of the hedge so that the cuttings are swept on to the ground. Cut without standing directly in front of the hedge, e.g. reach over a flower bed. Cut close to the ground from a standing position, e.g., for low shrubs. Using the Hedge Trimmer Cutting Techniques Vertical Cut Overhead Cut Horizontal Cut at ground level Horizontal Cut

pends a great deal on proper cutter blade adjustment. Properly adjusted blades will oscillate freely yet help prevent binding of cut material between blades. Adjust blades as follows: 1. Loosen all blade locknuts at least one full turn. 2. Tighten each blade shoulder bolt firmly, and then loosen the shoulder bolts 1/4 to 1/2 turn. Locknut Guide Bar Cutter Blades Shoulder Bolt Washer (should turn freely) Adjusting cutter blades Cutter blade adjustment 3. Working from the gearcase end, lock each bolt in place by firmly tighten- ing its locknut while preventing the shoulder bolt from turning. When shoulder bolt adjustment is cor- rect, there should be a gap of 0.25–0.50 mm between the cutter blades and the flat washers, and the flat washer be- neath each bolt head should turn freely. WARNING! The cutter blades are very sharp! Always wear gloves when working around the cutter assembly. CAUTION! Operating the trimmer with worn or improperly adjusted cutters will reduce cutter performance and may also damage your machine. Never operate the machine with damaged or worn cutters. Muffler This unit must never be operated with a faulty or missing spark arrester or muffler. Make sure the muffler is well secured and in good condition. A worn or damaged muffler is a fire hazard and may also cause hearing loss. Spark Plug Keep the spark plug and wire connections tight and clean. Fasteners Make sure nuts, bolts, and screws (except carburetor adjusting screws) are tight. WARNING! Before performing any maintenance, repair, or cleaning work on the unit, make sure the engine and cutting attachment are completely stopped. Discon- nect the spark plug wire before performing service or maintenance. WARNING! Non-standard accessories, cutting attach- ment, or replacement parts may not operate properly with your unit and may cause damage and lead to per- sonal injury. IMPORTANT! MAINTENANCE, REPLACEMENT OR REPAIR OF EMISSION CONTROL DEVICES AND SYSTEMS MAY BE PERFORMED BY ANY REPAIR ESTABLISHMENT OR INDIVIDUAL; HOWEVER, WARRANTY REPAIRS MUST BE PERFORMED BY A DEALER OR SERVICE CENTER AUTHORIZED BY ECHO, INC. THE USE OF PARTS THAT ARE NOT EQUIVALENT IN PERFORMANCE AND DURABILITY TO AUTHORIZED PARTS MAY IMPAIR THE EFFECTIVENESS OF THE EMISSION CONTROL SYSTEM AND MAY HAVE A BEARING ON THE OUTCOME OF A WARRANTY CLAIM. General maintenance NOTE: Using non-standard replacement parts could invalidate your Shindaiwa warranty.

following: ■ ■Remove all dirt and debris from the engine, check the cooling fins and air cleaner for clogging, and clean as necessary. ■ ■Carefully remove any accumula- tions of dirt or debris from the muf- fler and fuel tank. Check cooling air intake area at base of crank- case. Remove all debris. Dirt build-up in these areas can lead to engine overheating, fire, or prema- ture wear. Daily Maintenance WARNING! Always wear gloves when working around the cutter assembly. ■ ■Clean any debris or dirt from the- hedge trimmer cutter blades. ■ ■Lubricate the blades before use and after refueling. Check the cutters for damage or incorrect adjustment. ■ ■Check for loose or missing screws or components. Make sure the cut- ter attachment is securely fastened. ■ ■Check the entire machine for leak- ing fuel or grease. ■ ■Make sure nuts, bolts, and screws (except carburetor adjusting screws) are tight. Remove all dirt and debris from the engine and check the cooling fins Cooling fins Cooling fins Cooling fins Maintenance (continued) 10-Hour maintenance (more frequently in dusty conditions) CAUTION! Never operate the unit if the air cleaner assembly is damaged or missing! Unscrew Fasteners Loosen air cleaner cover screws Air Filter Element CAUTION! Before removing the spark plug, clean the area around the plug to prevent dirt and debris from getting into the engine’s internal parts. 10/15-Hour maintenance Remove and inspect spark plug Remove and clean or replace the spark plug. ■ ■Adjust the spark plug electrode gap to 0.6 mm (0.024 inch). If the spark plug must be replaced, use only an NGK BPMR8Y spark plug. Clean the spark plug and check the gap at the electrode. 0.6 mm (0.024 inch) 1. Close choke (cold start position). This prevents dirt from entering the carburetor throat when the air filter is removed. Brush accumulated dirt from air cleaner area. 2. Remove air filter cover. Brush dirt from inside cover. 3. Replace filter if it is damaged, very dirty, or the rubber sealing edges are deformed. ■ ■Lightly brush debris from filter. ■ ■Soak heavily soiled filters in water/ detergent solution to loosen dirt, then brush lightly. ■ ■Rinse with clean water and allow to dry completely before reuse. 4. Install air filter in air filter case. 5. Install air filter cover.

Remove and replace the fuel filter element Remove and replace the fuel filter element Outer Tube Gearcase Clamp Index Screw Gearcase Maintenance (continued) 50-hour maintenance Every 50 hours of operation; more frequnetly in dusty conditions: ■ ■ Remove and clean the cylinder cover and clean dirt and debris from the cylinder cooling fins. Remove and replace the fuel filter element. ■ ■Use a hooked wire to extract the fuel filter from inside the fuel tank. Inspect the fuel filter element. If it shows signs of contamination, replace with a genuine Shindaiwa replacement fuel filter element. CAUTION! Make sure you do not pierce the fuel line with the end of the hooked wire. The line is delicate and can be dam- aged easily. Before reinstalling the new filter element, inspect the condition of all the fuel system components (fuel pick-up line, fuel return line, tank vent line, tank vent, fuel cap and fuel tank). If damage, splitting or deterioration is noted, the unit should be removed from service until it can be inspected or repaired by a Shindaiwa-trained service technician. Gearcase lubrication To perform this operation, first remove the gearcase from the outer tube as follows: 1. Loosen the gearcase clamp bolt. 2. Remove the index bolt from the gearcase. Gearcase lubrication NOTE: Federal EPA regulations require all model year 2012 and later gasoline powered en- gines produced for sale in the United States to be equipped with a special low perme- ation fuel supply hose between the carburetor and fuel tank. When servicing model year 2012 and later equipment, only fuel supply hoses certified by EPA can be used to replace the original equipment supply hose. Fines up to $37,500 may be enforced for using an un-certified replacement part. Gearcase grease fitting A ■ ■Lubricate the cutter assembly gearcase by pumping one or two strokes of lithium-base grease into the grease fitting (A) using a lever- type grease gun. CAUTION! Over lubricating can cause the gear- case to operate sluggishly and can cause grease to leak out. Gearcase lubrication Lubricate cutter assembly and gearcase

Gearcase grease fitting B CAUTION! Do not remove the D-shaped shim washer from the gearcase clamp! The shim washer prevents damage from overtightening the tube clamp bolt. 3. Slide the gearcase out of the tube. Using a grease gun, pump lithium- base grease (about 10 grams) into the grease fitting (B) on the gearcase until you see old grease being purged from the gearcase. Purged grease will be visible in the outer tube cavity. 4. Clean up excess grease, then reassemble the gearcase onto the outer tube. Make sure the index bolt fits into the hole on the outer tube. Securely tighten both bolts. Maintenance (continued) 135 Hour Maintenance WARNING! Never operate the unit with a damaged or missing muffler or spark arrester! Operating with a missing or damaged spark arrester is a fire hazard and could also dam- age your hearing. Engine Cover Screws Muffler Cover Engine Cover Muffler Cover Screw Spark arrester screen Spark arrester cover Outlet Muffler gasket Muffler Gasket Muffler screws Muffler and spark arrester maintenance If the engine becomes sluggish and low on power, check and clean the spark arrester screen. 6. Inspect the cylinder exhaust port for any carbon buildup. 7. Gently tap the muffler on a wood surface to dislodge any loose car- bon. 8. Reassemble the spark arrester, muf- fler and engine cover in the reverse order of disassembly. 1. Remove the spark plug boot. 2. Remove the engine cover and muf- fler cover. 3. Remove the spark arrester screen and cover. 4. Clean the screen with a stiff bristle brush. 5. Remove the muffler. Screws

about 1/4 oz. of engine oil into the cylinder through the spark plug hole. Slowly pull the recoil starter 2 or 3 times so oil will evenly coat the interior of the engine. Reinstall the spark plug. ■ ■Before storing the unit, repair or replace any worn or damaged parts. ■ ■Remove the air cleaner element from the carburetor and clean it thor- oughly with soap and water. Let dry and reassemble the element. ■ ■Store the unit in a clean, dust-free area. Long Term Storage Whenever the unit will not be used for 30 days or longer, use the following procedures to prepare it for storage: ■ ■Clean external parts thoroughly and apply a light coating of oil to all metal surfaces. ■ ■Drain all the fuel from the carburetor and the fuel tank. To do so: 1. Prime the primer bulb until no more fuel is passing through. 2. Start and run the engine until it stops running. 3. Repeat steps 1 and 2 until the en- gine will no longer start. CAUTION! Gasoline stored in the carburetor for extended periods can cause hard starting, and could also lead to increased service and maintenance costs. IMPORTANT! All stored fuels should be stabilized with a fuel stabilizer such as STA-BIL™. NOTE: Damage resulting from stale or con- taminated fuel is not covered by the Shindaiwa warranty policy. Carburetor Adjustment Engine Break-In New engines must be operated a minimum duration of two tanks of fuel break-in before carburetor adjustments can be made. During the break-in period your engine performance will increase and exhaust emissions will stabilize. Idle speed can be adjusted as required. High Altitude Operation This engine has been factory adjusted to maintain satisfactory starting, emission, and durability performance up to 1,100 feet above sea level (ASL) (96.0 kPa). To maintain proper engine operation and emission compliance above 1,100 feet ASL the carburetor may need to be adjusted by an authorized Shindaiwa service dealer. NOTE: Every unit is run at the factory and the carburetor is set in compliance with emission regulations. Carburetor adjustments, other than idle speed, must be performed by an authorized Shindaiwa dealer. IMPORTANT! If the engine is adjusted for operation above 1,100 feet ASL, the carburetor must be re-adjusted when operating the engine below 1,100 feet ASL, otherwise severe engine damage may result. Idle ad- justment screw Adjusting engine idle 3. If a tachometer is available, adjust idle. Check Specifications page for correct idle speed. Adjusting Engine Idle The engine must return to idle speed whenever the throttle lever is re- leased. Idle speed is adjustable, and must be set low enough to permit the engine clutch to disengage the cutting attachment. Idle Speed Adjustment 1. Place the trimmer on the ground, then start the engine, and then allow it to idle 2-3 minutes until warm. 2. If the attachment moves when the engine is at idle, reduce the idle speed by turning the idle adjust- ment screw counter-clockwise. WARNING! The cutting attachment must NEVER move at engine idle! If the idle speed cannot be adjusted by the procedure described here, return the unit to your Shindaiwa dealer for inspection. NOTE: Carburetor fuel mixture adjustments are preset at factory and cannot be serviced in the field IMPORTANT! If you note excessive carbon buildup, consult with an authorized Shindaiwa servicing dealer.

Low fuel quality. Let cool completely and restart. Ref ll with fresh, clean unleaded gasoline with a pump octane of 89 or higher mixed with an air cooled engine oil that meets or exceeds ISO-L-EGD and/or JASO FD classif ed oils at 50:1 gasoline/oil ratio. What To Check Possible Cause Remedy ENGINE DOES NOT START OR HARD TO START NO NO NO NO Does the engine crank? Good compression? Does the tank contain fresh fuel of the proper grade? Is fuel visible and moving in the return line when priming? Is there spark at the spark plug wire terminal? Check the spark plug. Faulty recoil starter. Fluid in the crankcase. Internal damage. Loose spark plug. Excess wear on cylinder, piston, rings. Fuel incorrect, stale, or contaminated; mixture incorrect. Check for clogged fuel f lter and/or vent. Priming pump not functioning properly. The ignition switch is in “O” (OFF) position. Shorted ignition ground. Faulty ignition unit. If the plug is wet, excess fuel may be in the cylinder. The plug is fouled or improperly gapped. The plug is damaged internally or of the wrong size. Consult with an authorized Shindaiwa servicing dealer. Tighten and re-test. Consult with an authorized Shindaiwa servicing dealer. Ref ll with fresh, clean unleaded gasoline with a pump octane of 89 or higher mixed with an air cooled engine oil that meets or exceeds ISO-L-EGD and/or JASO FD classif ed oils at 50:1 gasoline/oil ratio. Replace fuel f lter or vent as required. Re-start. Consult with an authorized Shindaiwa servicing dealer. Move switch to “I” (ON) position and re-start. Consult with an authorized Shindaiwa servicing dealer. See "Starting a Flooded Engine" Clean and gap the spark plug. Check the Specif cations section for the correct plug and gap for your unit. Restart. Replace the spark plug. Check the Specif cations section for the correct plug and gap for your unit. Restart. NO YES What To Check Possible Cause Remedy ENGINE DOES NOT START YES YES YES YES

Engine is rough at all speeds. May also have black smoke and/or unburned fuel at the exhaust. Operator is overworking the unit. Carburetor mixture is too lean. Improper fuel ratio. Fan, fan cover, cylinder f ns dirty or damaged. Carbon deposits on the piston or in the muf er. Clogged air cleaner element. Loose or damaged spark plug. Air leakage or clogged fuel line. Water in the fuel. Piston seizure. Faulty carburetor and/or diaphragm. Overheating condition. Improper fuel. Carbon deposits in the combustion chamber. Use a lower throttle setting. Consult with an authorized Shindaiwa servicing dealer. Ref ll with fresh, clean unleaded gasoline with a pump octane of 89 or higher mixed with an air cooled engine oil that meets or exceeds ISO-L-EGD and/or JASO FD classif ed oils at 50:1 gasoline/oil ratio. Clean, repair or replace as necessary. Consult with an authorized Shindaiwa servicing dealer. Service the air cleaner element. Tighten or replace the spark plug. Check the Specif cations section for the correct plug and gap for your unit. Repair or replace fuel f lter and/or fuel line. Ref ll with fresh, clean unleaded gasoline with a pump octane of 89 or higher mixed with an air cooled engine oil that meets or exceeds ISO-L-EGD and/or JASO FD classif ed oils at 50:1 gasoline/oil ratio. Consult with an authorized Shindaiwa servicing dealer. Consult with an authorized Shindaiwa servicing dealer. Ref ll with fresh, clean unleaded gasoline with a pump octane of 89 or higher mixed with an air cooled engine oil that meets or exceeds ISO-L-EGD and/or JASO FD classif ed oils at 50:1 gasoline/oil ratio. Consult with an authorized Shindaiwa servicing dealer. What To Check Possible Cause Remedy LOW POWER OUTPUT Engine is knocking. Troubleshooting Guide (continued)

Clogged fuel f lter. Lean fuel/air mixture. Idle speed set too low. Ignition switch turned of . Fuel tank empty. Water in the fuel. Clogged fuel f lter. Shorted spark plug or loose terminal. Ignition failure. Piston seizure. Ground (stop) wire is disconnected, or switch is defective. Overheating due to incorrect spark plug. Overheated engine. Clean the air f lter. Replace the fuel f lter. Consult with an authorized Shindaiwa servicing dealer. Adjust idle. Check Specif cations page for correct idle speed. Reset the switch and re-start. Ref ll with fresh, clean unleaded gasoline with a pump octane of 89 or higher mixed with an air cooled engine oil that meets or exceeds ISO-L-EGD and/or JASO FD classif ed oils at 50:1 gasoline/oil ratio. Replace fuel f lter. Clean or replace spark plug. Check the Specif cations section for the correct plug and gap for your unit. Tighten the terminal. Replace the ignition unit. Consult with an authorized Shindaiwa servicing dealer. Test and replace as required. Replace the spark plug. Check the Specif cations section for the correct plug and gap for your unit. Restart. Idle engine until cool. Symptom Possible Cause Remedy Engine stops abruptly. Engine diffi cult to shut off. Troubleshooting Guide (continued) Engine idle too high. Broken clutch spring or worn clutch spring boss. Loose attachment holder. Warped or damaged attachment. Loose gearcase. Cutting attachment moves at engine idle. Excessive vibration. Cutting attachment will not move. Adjust idle. Check Specif cations page for correct idle speed. Replace spring/shoes as required, check idle speed. Inspect and re-tighten holders securely. Inspect and replace attachment as required. Tighten gearcase securely. Bent main shaft/worn or damaged bushings. Shaft not installed in powerhead or gearcase. Broken shaft. Damaged gearcase. Inspect and replace as necessary. Inspect and reinstall as required. Idle set too high. Adjust idle. Check Specif cations page for correct idle speed. Engine will not idle down. Engine has an air leak. Consult with an authorized Shindaiwa servicing dealer. Consult with an authorized Shindaiwa servicing dealer.

PRODUCT SOLD IN USA AND CANADA BEGINNING 01/01/2013 ECHO, INC’S RESPONSIBILITY ECHO Incorporated’s (ECHO, INC.) Limited Warranty, provides to the original purchaser that this Shindaiwa product is free from defects in material and workmanship. Under normal use and maintenance from date of purchase, ECHO, INC. agrees to repair or replace at it’s discretion, any defective product free of charge at any authorized Shindaiwa servicing dealer within listed below application time periods, limitations and exclusions. THIS LIMITED WARRANTY IS ONLY APPLICABLE TO SHINDAIWA PROD- UCTS SOLD BY AUTHORIZED SHINDAIWA DEALERS. IT IS EXTENDED TO THE ORIGINAL PURCHASER ONLY, AND IS NOT TRANSFERABLE TO SUBSEQUENT OWNERS EXCEPT FOR EMISSION RELATED PARTS. Repair parts and accesso- ries replaced under this warranty are warranted only for the balance of the original unit or accessory warranty period. Any dam- age caused by improper installation or improper maintenance is not covered by this warranty. All parts or products replaced under warranty become the property of ECHO, INC. This warranty is separate from the Emission control warranty statement supplied with your new product. Please consult the Emission Control Warranty Statement for details regarding emission related parts. For a list of Authorized Shindaiwa Dealers refer to WWW.SHINDAIWA.COM or call 1-877-986-7783. OWNER’S RESPONSIBILITY To ensure trouble free warranty coverage it is important that you register your Shindaiwa equipment on-line at WWW.SHINDAIWA. COM or by filling out the warranty registration card supplied with your unit. Registering your product confirms your warranty cover- age and provides a direct link if we find it necessary to contact you. The owner shall demonstrate reasonable care and use, and follow preventative maintenance, storage, fuel and oil usage as pre- scribed in the operator’s manual. Should a product difficulty occur, you must, at your expense, deliver or ship your Shindaiwa unit to an authorized Shindaiwa servicing dealer for warranty repairs (within the applicable warranty period), and arrange for pick-up or return of your unit after the repairs have been made. For your nearest authorized Shindaiwa servicing dealer, call Shindaiwa’s Dealer Referral Center, at 1-877-986-7783 or you can locate a Shindaiwa servicing dealer at WWW.SHINDAIWA.COM. Should you require assistance or have questions concerning Shindaiwa’s Warranty Statement, you can contact our Consumer Product Support Department at 1-800-673-1558 or contact us through the web at WWW.SHINDAIWA.COM. PRODUCT WARRANTY PERIOD RESIDENTIAL APPLICATION • 5 YEAR WARRANTY - Units for residential, or non-income producing use will be covered by this limited warranty for five (5) years from date of purchase. EXCEPTIONS: • For engine powered products, the electronic ignition module, flexible drive cable, and solid drive shaft are warranted for the life* of the product on parts only. • Cutting attachments such as, but not limited to, bars, chains, sprockets, tines, blades, PowerBroomTM, belts, and nylon trimmer heads for residential or non-income producing use will be covered for failures due to defects in material or workmanship for a period of 60 days from original product purchase date. Any misuse from contact with concrete, rocks, or other structures is not covered by this warranty. • Multipurpose Tool Attachments carry the same warranty duration as the units they are designed to fit. COMMERCIAL APPLICATION • 90 DAY WARRANTY - All Chain Saws and Cut-Off Saws for commercial, institutional, agricultural, industrial, or income produc- ing use will be covered by this limited warranty for 90 Days from the date of purchase. • 2 YEAR WARRANTY - Units for commercial, institutional, agricultural, industrial, or income producing use will be covered by this limited warranty for two (2) years from the date of purchase. EXCEPTIONS: • For engine powered products, the electronic ignition module, flexible drive cables, and solid drive shafts are warranted for the life* of the product on parts only. • Cutting attachments such as, but not limited to, bars, chains, sprockets, tines, blades, PowerBroomTM, belts, and nylon trimmer heads for commercial, institutional, agricultural, industrial, rental, or income producing will be covered for fail- ures due to defects in material or workmanship for a period of 30 days from original product purchase date. Any misuse from contact with concrete, rocks, or other structures is not covered by this warranty. • Multipurpose Tool Attachments carry the same warranty duration as the units they are designed to fit. RENTAL APPLICATION - 90 DAYS WARRANTY • Units for rental use will be covered against defects in material and workmanship for a period of 90 days from the date of pur- chase. * ECHO INC’s liability under the “Lifetime” coverage is limited to furnishing parts specified under the PRODUCT Warranty PERIOD section of this warranty statement for “Life” free of charge for a period of ten (10) years after the date of the complete unit’s final production.

• 90-day all applications ATTENTION ENGINE POWERED PRODUCT OWNERS This Shindaiwa engine powered product is a quality-engineered unit which has been manufactured to exact tolerances to provide superior performance. To help ensure the performance of the unit, it is required to use engine oil which meets the ISO-L-EGD Standard per ISO/CD 13738 and JASO M345/FD Standards. Shindaiwa Red ArmorTM and Shindaiwa OneTM are a premium engine oil specifically formulated to meet ISO-L-EGD (ISO/CD 13738) and JASO M345/FD Standards. The use of engine oils designed for other applications, such as for outboard motors or lawnmowers can result in severe engine damage, and will void your engine limited warranty. THIS WARRANTY DOES NOT COVER DAMAGE CAUSED BY: • Lack of lubrication or engine failure, due to the use of engine oils that do not meet the ISO-L-EGD (ISO/CD 13738) and JASO M345/FD Standards. Shindaiwa Red ArmorTM and Shindaiwa OneTM Engine Oil meets the ISO-L-EGD and JASO M345/FD Standard. Emission related parts are covered for 2 years regardless of engine oil used, per the statement listed in the EPA or California Emission Control Warranty Explanation. • Damage caused by use of gasohol, containing methanol (wood alcohol), or gasoline containing less than 89 octane. Only use gasoline which contains 89 octane or higher. Gasohol which contains a maximum 10% ethanol (grain alcohol) or 15% MTBE (methyl/tertiary/butyl/ether) is also approved. The prescribed mixing ratio of gasoline to oil is listed on the Shindaiwa oil label and covered in your operator’s manual. • Engine damage caused by use of ether or any starting fluids. • Damage caused by tampering with engine speed governor or emission components, or running engines above specified and recommended engine speeds as listed in your operator’s manual. • Operation of the unit with improperly maintained/removed cutting shield or removed/damaged air filter. • Damage caused by dirt, pressure or steam cleaning the unit, salt water, corrosion, rust, varnish, abrasives, and moisture. • Defects, malfunctions or failures resulting from abuse, misuse, neglect, modifications, alterations, normal wear, improper servic- ing, or use of unauthorized attachments. • Incorrect storage procedures, stale fuel, including failure to provide or perform required maintenance services as prescribed in the operator’s manual. Preventative maintenance as outlined in the operator’s manual is the customer’s responsibility. • Failures due to improper set-up, pre-delivery service or repair service by anyone other than authorized Shindaiwa servicing dealer during the warranty period. • Certain parts and other items are not warranted, including but not limited to: lubricants, starter cords, and engine tune-ups. • Use of spark plugs other than those meeting performance and durability requirements of the OEM spark plug listed in the Opera- tor’s Manuals. • Overheating or carbon scoring failures due to restricted, clogged exhaust port or combustion chamber, including damage to spark arrester screen. • Adjustments after the first (30) thirty days and beyond, such as carburetor adjustment and throttle cable adjustment. • Damage to gears or gear cases caused by contaminated grease or oil, use of incorrect type or viscosity of lubricants, and/or failure to comply with recommended grease or oil change intervals. • Damage caused by pump or sprayer running dry, pumping or spraying caustic or flammable materials, or lack of or broken strainers. • Additional damage to parts or components due to continued use after operational problem or failure occurs. Should operational problem or failure occur, the product should not be used, but delivered as is to an authorized Shindaiwa servicing dealer. It is a dealer’s and/or customer’s responsibility to complete and return the warranty registration card supplied with your Shindaiwa product or by visiting WWW.SHINDAIWA.COM. Your receipt of purchase including date, model and serial number must be main- tained and presented to an authorized Shindaiwa servicing dealer for warranty service. Proof of purchase rests solely with the cus- tomer. Some states do not allow limitations on how long an implied warranty lasts, so the above limitations may not apply to you. Some states do not allow the exclusion or limitation of incidental or consequential damages, so you may also have other specific legal rights which vary from state to state. This limited warranty is given by ECHO Incorporated, 400 Oakwood Rd., Lake Zurich, IL 60047. DISCLAIMER OF IMPLIED WARRANTIES This limited warranty is in lieu of all other expressed or implied warranties, including any warranty of FITNESS FOR A PARTICU- LAR PURPOSE OR USE and any implied warranty of MERCHANTABILITY otherwise applicable to this product. ECHO, INC. and its affiliated companies shall not be liable for any special incidental or consequential damage, including lost profits. There are no warranties extended other than as provided herein. This limited warranty may be modified only by ECHO, INC. X7561120400 10/12

Lake Zurich, IL 60047-1564 U.S.A. Telephone: 1-877-986-7783 Fax: 1-847-540-8416 www.shindaiwa.com Yamabiko Corporation 7-2 Suehirocho 1-Chome, Ohme, Tokyo, 198-8760, Japan Phone: 81-428-32-6118 Fax: 81-428-32-6145 Servicing Information Parts/Serial Number Genuine Shindaiwa Parts and Assemblies for your Shindaiwa products are available only from an Authorized Shindaiwa Dealer. When you do need to buy parts always have the Model Number, Type and Serial Number of the unit with you. You can find these numbers on the engine. For future reference, write them in the space provided below. Model No. _____________ SN. ______________ Service Service of this product during the warranty period must be performed by an Authorized Shindaiwa Service Dealer. For the name and address of the Authorized Shindaiwa Service Dealer nearest you, ask your retailer or call: 1-877- 986-7783. Dealer information is also available on WWW.SHINDAIWA.COM. When presenting your unit for Warranty service/repairs, proof of purchase is required. Consumer Product Support If you require assistance or have questions concerning the application, operation or maintenance of this product you may call the Shindaiwa Consumer Product Support Department at 1-877-986-7783 from 8:30 am to 4:30 pm (Central Standard Time) Monday through Friday. Before calling, please know the model and serial number of your unit. Warranty Registration To ensure trouble free warranty coverage it is important that you register your Shindaiwa equipment by filling out the warranty registration card supplied with your unit. Registering your product confirms your warranty coverage and pro- vides a direct link if we find it necessary to contact you. Additional or Replacement Manuals Replacement Operator and Parts Catalogs are available from your Shindaiwa dealer or at WWW.SHINDAIWA.COM or by contacting the Consumer Product Support Department (1-877-986-7783). Always check WWW.SHINDAIWA. COM for updated information. Copyright© 2013 By Echo, Incorporated All Rights Reserved. T17913001001/T17913999999