Siemens VersiCharge Quick Start Manual

Electric Vehicle Charging Station Sample Tools Used Certified Electrician (Recommended) 2 pole, 40 amp circuit breaker Cordless Drill (Phillips Bit) #8 copper wire, 3 conductors 240 V AC Voltmeter NEMA 6-50 Outlet (if not hardwiring) Powering your drive into the future! The information provided in this brochure contains merely general descriptions or characteristics of performance which in case of actual use do not always apply as described or which may change as a result of further development of the products. An obligation to provide the respective characteristics shall only exist if expressly agreed in the terms of contract. Siemens Industry, Inc. 5400 Triangle Parkway Norcross, GA 30092 1-800-241-4453 [email protected] Order No. RPBR-VERQS-0814 | Printed in USA | All rights reserved. © 2014, Siemens Industry, Inc. www.usa.siemens.com/versicharge All product designations may be trademarks or product names of Siemens AG or supplier companies whose use by third parties for their own purposes could violate the rights of the owners. NEC® is a registered trademark of the National Fire Protection Association. Refer to your USB key chain before installation to: • Review the complete Installation and Operations Manual • Learn how to use the amperage adjustment dial or participate in utility programs using the VersiCharge remote control interface • Find additional information on how to future proof your home’s energy consumption

illuminate. If it does not, verify that the outlet or wire is putting out 240 or 208 VAC. With the Power Available light on, plug the EVSE into the car. If you have any fault lights, please consult Installation and Operations Manual on the provided USB key chain. WARNING! Do not force the connector into the receiver on the vehicle. If the connection between the receiver and connector shows any resistance, inspect the pins in each, and if damage is found, call a qualified service person. WARNING! When installed outdoors, due to the risk of moisture, cord and plug installations require a NEMA outdoor rated receptacle and enclosure. Installing outdoors without properly rated outdoor receptacles and enclosures will violate listings and void the device warranty. Outdoor cord-and- plug installations must be bottom fed only. 6 Screw down charging station 1 2 3 5 6 4 1. Pause/Reset Button 2. Charging 3. Fault* 4. Power Available 5. Infrared Service Portal 6. Time Delay Button (2/4/6/8 hr delay options) Technical support: 1-800-241-4453 Visit our website: www.usa.siemens.com/versicharge VersiCharge Quick Start Guide VersiCharge Quick Start Guide DANGER Explosion Hazard This equipment has arcing or sparking parts that should not be exposed to flammable vapors. This equipment should be installed at least 18 inches above floor or ground level. Use extreme caution and follow instructions carefully. * For troubleshooting information refer to the complete Installation and Operations manual on the USB key chain provided or call technical support 1-800-241-4453. DANGER Hazardous Voltage Will cause death, serious injury or substantial property damage. Turn off power supplying equipment before working inside. DANGER Hazardous Voltage Will cause death, serious injury or substantial property damage. Turn off power supplying equipment before working inside. 1 Run Wire (If a 240V receptacle is already installed in the desired installation location with a dedicated 40 A circuit, please skip to step 3) A dedicated 40 amp, 2 pole circuit breaker is required. Ensure there is empty space in the load center and that the electrical system has sufficient capacity for a continuous 30 A load. Wire conductors (copper only) per all NEC and local jurisdiction requirement. Snake wiring through walls or run conduit on exposed surfaces. Be sure to tighten down wire in circuit breakers per manufacturer’s recommendation. NOTE: Please consider your planned installation location for the mounting bracket when choosing the location to which you will run the wire. 2 Wire Outlet (Skip this step if hardwiring the unit) 2 Wire Outlet (continued) (Skip this step if hardwiring the unit) Snake wiring through wall or run conduit on exposed surfaces. 4 3.b Wire up VersiCharge (Skip if using receptacle) 3 Select location and add mounting bracket (match bracket location with orientation of the ground hole as shown below) Locate a stud within the wall that can handle the 14+ lb load of the VersiCharge. For concrete or other walls, install appropriate anchors. If using receptacle, ensure that power cord will reach to the outlet. Using a 7/16” socket, attach mounting bracket to wall in compliance with all National Electrical Code® (NEC) and local jurisdiction requirements, using the 2 lag screws provided. 5 Mount VersiCharge 7 Check System