Shimaden SR90 Series Instruction Manual

The smaller the value of response code, the higher the priority of the response code; When two or more response codes are generated, a response code of higher priority order is returned. 5-6. Details of communication data addresses (1) Data address and read/write • In a data address, binary numbers (16 bit data) are expressed by hexadecimal numbers, with 4 bits as a unit. • R/W means that data are capable of being read and written. • R means that data are only for reading. • W means that data are only for writing. • In case a data address only for ...

b7b6b5 000 001 010 011 100 101 110 111 0 1 2 3 4 5 6 7 NUL TC7 (DLE) 0 1 2 3 4 5 6 7 8 9 TC1 (SOH) DC1 ! TC2 (STX) DC2 TC3 (ETX) DC3 # TC4 (EOT) DC4 $ TC5 (ENQ) TC8 (NAK) % TC6 (ACK) TC9 (SYN) & BEL TC10 (ETB) FE0 (BS) CAN ( FE1 (HT) EM ) FE2 (LF) SUB ∗ : FE3 (VT) ESC + ; [ FE4 (FF) IS4 (FS) , < \ FE5 (CR) IS3 (GS) SO IS2 (RS) . > ^ SI IS1 (US) DEL b4 ~ b1 0000 0001 0010 0011 0100 0101 0110 0111 1000 1001 1010 1011 1100 1101 1110 1111 0 1 2 3 4 5 6 7 8 9 A B C D E F _ _ / SP = ? @ A P B C D E F G H I J Q R S T U V W X Y Z p q r s t u v w x y z K L M N O a b c d e f g h i j k l m n o ] ...

Thus, the above data can be read. (3) Abnormal response format to read command (R) • The following is the abnormal response format (text portion) to read commands (R): (The basic format portions I and II are common to all commands and responses.) • d( ): indicating that it is a response to a read command (R) is inserted. • e( , ): A response code indicating that it is an abnormal response to the read command (R) is inserted. • For details of abnormal response code, refer to 5-5. De ...

Data address (hex) Parameter R/W Setting range 0704 0705 0706 0707 0708 0709 R/W R/W R/W R/W R/W R/W UNIT Unit of input data Refer to 7-1. Table of measuring range codes 0: None 1: 0.1 2: 0.01 3: 0.001 –1999 ~ 9989 UNIT –1989 ~ 9999 UNIT RANGE Reserved DP SC_L SC_H 0: "˚C" 1: "˚F" Unchangeable except linear input Measuring range 0 0.0 0 0 0 -199.9 -199.9 -200 -200 0 0 0 0 0 0 -199.9 400.0 800.0 200.0 200.0 -100.0 -50.0 50.0 0.0 200.0 -100.0 -50.0 0.0 100.0 100.0 50.0 200.0 1700 1200 1300 1300 2300 700 600 600 600 500 1700 1800 °C °F Code 01 02 03 04 05 06 07 08 09 10 11 12 1 ...

• No punctuation code is used between data and data. • The number of data is determined by the number of data (f: ) of the communication command format. • Each data is expressed by binary 16 bits (1 word), excluding a decimal point, as a unit. The position of decimal point is fixed in each data. • 16 bit data are split into 4 bit groups and respectively converted to ASCII data. • For details of data, refer to 5-3. Details of read commands (R) and 5-4. Details of write command (W). e : Response code ...

• When a portion is read in reply to a read command (R), or written in replay to a write command (W), normal response code "0", "0" (30H, 30H) is returned. (5) Option-related parameters • When the data address of a parameter which is not added as an option is designated, abnormal response code "0", "C" (30H, 43H)"Specification, option error" is returned to a read command (R) as well as a write command (W). If an address of data only for reading is read, however, the (0000H) data are returned. (6) Parameters not shown in front panel displays ...