Sharp AL-1600 Service Manual

the projections on the front frame side and the rear frame side of the copy lamp unit to the corner frame, and tighten the wire fixing screw. (3) Main scanning direction (FR direction) distortion adjustment This adjustment must be performed in the following cases: • When the mirror base drive wire is replaced. • When the lamp unit, or No. 2/3 mirror holder is replaced. • When a copy as shown is made. 1) Set A3 (11" x 17") white paper on the original table as shown below. 2) Open the original cover and make a normal (100 ...

solenoid) D. Resist roller clutch/Resist roller E. Paper feed clutch/Paper feed roller (Semi-circular roller) 9. Manual multi paper feed section No. Content A Manual multi paper feed section B Manual transport clutch C Manual paper feed clutch D Manual transport roller/Manual paper feed roller E Multi feed solenoid A. Manual multi paper feed (1) (2) (2) (3) � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � AL-1610 11 � ...

Initial value Set range 26 5 Counter mode setting Used to set the print counter mode in A3 or 11" × 17". Used to display the currently set counter value with the numbers at right. After entering the set value, press the start key, and the set value is stored. Key operation/Display 0: Total/Developer = 2 counts Maintenance = 2 counts 1: Total/Developer = 1 count Maintenance = 2 counts 2: Total/Developer = 2 counts Maintenance = 1 count 3: Total/Developer = 1 count Maintenance = 1 count 6 Destination setting Used to display the current destinatio ...

Initial value Set range 26 5 Counter mode setting Used to set the print counter mode in A3 or 11" × 17". Used to display the currently set counter value with the numbers at right. After entering the set value, press the start key, and the set value is stored. Key operation/Display 0: Total/Developer = 2 counts Maintenance = 2 counts 1: Total/Developer = 1 count Maintenance = 2 counts 2: Total/Developer = 2 counts Maintenance = 1 count 3: Total/Developer = 1 count Maintenance = 1 count 6 Destination setting Used to display the current destinatio ...

C. Manual paper feed clutch Disassembly: Set up the shutter arm (1) then remove it. Assembly: Install so that the boss section of the fulcrum arm (2) comes between ribs. Disassembly: Set up the cam transmission arm (2), and remove it. Assembly: Install so that the cam transmission arm (2) is under the roller arm (A). � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � AL-1610 11 – 9 ...

Initial value Set range 41 3 Document sensor light reception level display Used to display the light reception level and the detection level of the document sensor. (The sensor level adjusted with SIM 41-2 is dis- played.) Key operation Display Light reception/Detection level select: Magnification ratio display key Display at the 3rd digit "A": Light reception level display "b": Document detection level lighting LED Sensor select: Magnification ratio select key Sensor A: A3 document size LED Sensor B: A4 document size LED Sensor C: A4R document ...

Display Content Major cause Copy quantity display "– –" The correction value calculated is over 5%. • Improper position of reference width line of the reference white plate • Improper installation of CCD unit Paper jam lamp ON Reference line scanning error • Defective CCD • No reference white plate (6) Sub scanning direction (scanning direction) magnification ratio adjustment (SIM 48-2, SIM 48-5) a. OC mode in copying Note: • Before performing this adjustment, be sure to check that the CCD unit is properly installed. 1) Put a scale on the ori ...

the off center adjustment at each paper feed port is displayed on the display section in 2 digits. 5) Enter the set value and press the start key. The set value is stored and a copy is made. Mode Specification SIM Set value Set range Original off center mode (SPF mode) Single: Center ± 3.0mm SIM 50-16 Add 1: 0.1mm shift to R side Reduce 1: 0.1mm shift to L side 1 ~ 99 Duplex: Center ±3.5mm (8) Original sensor adjustment (SIM 43-3) 1) Execute SIM 41-2. 2) Set A3 (11" x 17") paper on the OC table. 3) ...