Worcester DT10RF Instruction Manual

with domestic hot water programmer FOR GREENSTAR CDi, GREENSTAR i JUNIOR AND GREENSTAR Si MODELS ALSO GREENSTAR i SYSTEM AND GREENSTAR CDi SYSTEM MODELS (ONLY WHEN USED WITH THE OPTIONAL INTEGRAL DIVERTER VALVE) INSTRUCTION MANUAL OPERATING AND INSTALLATION UK/IE 8_716_115_493a 9/2/09 09:45 Page 1

TECHNICAL 08705 266241 SERVICE 08457 256206 SPARES 01905 752571 LITERATURE 01905 752556 TRAINING 01905 752526 SALES 01905 752640 WEBSITE worcester-bosch.co.uk SYMBOLS Domestic Hot Water Radio Frequency (RF) Transmitter PLEASE READ THESE INSTRUCTIONS CAREFULLY BEFORE STARTING THESE INSTRUCTIONS ARE APPLICABLE TO THE WORCESTER BOSCH MODEL(S) STAT- ED ON THE FRONT COVER OF THIS MANUAL ONLY AND MUST NOT BE USED WITH ANY OTHER MAKE OR MODEL THESE INSTRUCTIONS APPLY IN THE UK ONLY AND SHOULD BE FOLLOWED EXCEPT FOR ANY STATUTORY OBLIGATION IF YOU ARE IN ANY DOUBT CONTACT WORCESTER BOSCH TECHNICAL HELPLINE THIS ACCESSORY MUST BE FITTED BY A COMPETENT PERSON. FAILURE TO COMPLY COULD LEAD TO PROSECUTION. LEAVE THESE INSTRUCTIONS WITH THE USER OR AT THE APPLIANCE. ABBREVIATIONS CH = Central Heating DHW = Domestic Hot Water RF = Radio Frequency DLS = Daylight Saving BST = British Summer Time GMT = Greenwich Mean Time C = Celsius (Centigrade) IP = Ingress Protection V = Volt m = metre mA = milliAmpere DEFINITIONS (DLS/BST) Summer time begins: Last Sunday in March at 1:00 am GMT (Clocks are put forward by 1 hour) Summer time ends: Last Sunday in October at 2:00 am BST (Clocks are put back by 1 hour) PROPER BATTERY RECYCLING Electronic devices and batteries, rechargeable or not, should not be disposed of into ordinary household waste. Instead, they must be recycled properly to protect the environment and cut down the waste of precious resources. Your local waste management authority can supply details concerning the proper disposal of batteries. PROTECT YOUR ENVIRONMENT DT10RF PROGRAMMER INSTRUCTION MANUAL 8 716 115 493a (02.2009) OPERATING & INSTALLATION INSTRUCTIONS 8_716_115_493a 9/2/09 09:45 Page 3

GENERAL INFORMATION . . . . . . . . . . . . . . . . . . . . . . . . . . .2 DIGISTAT OPERATING CONTROLS . . . . . . . . . . . . . . . . . . .3 PRE-PROGRAMMED SETTINGS . . . . . . . . . . . . . . . . . . . . .4 ADJUSTING TIME AND TEMPERATURE . . . . . . . . . . . . . . .5 DIGISTAT / USER OPTIONS . . . . . . . . . . . . . . . . . . . . . . . . .7 RECEIVER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13 OPERATIONAL CONTROLS . . . . . . . . . . . . . . . . . . . . . . . .13 PRE-SET PROGRAMS . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15 PROGRAMMABLE SETTINGS . . . . . . . . . . . . . . . . . . . . . .16 RECEIVER INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . . .22 DIGISTAT INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23 SETTING UP RF LINK . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23 MOUNTING DIGISTAT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .25 CHECK PREVIOUSLY INSTALLED UNITS . . . . . . . . . . . . .26 CANCEL SIGNAL STRENGTH . . . . . . . . . . . . . . . . . . . . . .27 DIGISTAT / INSTALLER OPTIONS . . . . . . . . . . . . . . . . . . . .28 BATTERY CHANGE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .30 MAINTENANCE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .31 CONTENTS OPERATING & INSTALLATION INSTRUCTIONS DT10RF PROGRAMMER INSTRUCTION MANUAL 8 716 115 493a (02.2009) 8_716_115_493a 9/2/09 09:45 Page 4

Low Voltage Directive (2006/95/EC) Electro-Magnetic Compatibility Directive (89/336/EEC) EC Marking Directive (93/68/EEC) STANDARD PACKAGE: Programmable RF receiver Remote RF transmitter Screws (x2) Wall Plugs (x2) Instructions Batteries (x2) AA Alkaline DESCRIPTION UNITS DT10RF Receiver Digistat Transmitter Dimensions mm -- 137 x 96.5 x 31.3 Electrical supply V 24 3 Radio frequency MHz 433 433 Radio signal range The range may be affected by the composition / density and number of walls between the Digistat RF and receiver. 30 metres typically, through two internal plasterboard walls and a ceiling. 26 metres typically, through three internal plasterboard walls and a ceiling. 17 metres typically, through two internal plasterboard walls a ceiling and one external cavity wall. These distances are provided for guidance only, many factors can affect the range of the transmitter, including metal pipework, appliances and even furniture. Temperature range °C 5 to 32 5 to 32 Ambient operating temperature °C 0 to +50 0 to +40 Humidity operating range % non condensing up to 45°C 30 to 95 25 to 90 Class of operation II -- Degrees of protection IP 24 30 Accuracy at 25°C sec/day better than ±1 - Battery life (with alkaline batteries) years N/A approx. 2 Battery back up time and date years min. 10 10 Shortest switching period minutes 1 1 Hot water pre-heat settings number 3 ON / 3 OFF -- Central heating settings number -- 6 Hot water and Central heating programs days 7 1 TECHNICAL DATA DT10RF PROGRAMMER INSTRUCTION MANUAL 8 716 115 493a (02.2009) OPERATING & INSTALLATION INSTRUCTIONS 1 8_716_115_493a 9/2/09 09:45 Page 5

A programmable room thermostat is both a pro- grammer and a room thermostat. A programmer allows you to set ‘On’ and ‘Off’ time periods to suit your own lifestyle. A room thermostat works by sensing the air tem- perature, switching on the heating when the air temperature falls below the thermostat setting, and switching it off once this set temperature has been reached. So, a programmable room thermostat lets you choose what times you want the heating to be on, and what temperature it should reach while it is on. It will allow you to select different tempera- tures in your home at different times of the day (and days of the week) to meet your particular needs. Turning a programmable room thermostat to a higher setting will not make the room heat up any faster. How quickly the room heats up depends on the design of the heating system, for example, the size of boiler and radiators. Neither does the setting affect how quickly the room cools down. Turning a programmable room thermostat to a lower setting will result in the room being con- trolled at a lower temperature, and saves energy. The way to set and use your programmable room thermostat is to find the lowest temperature set- tings that you are comfortable with at the differ- ent times you have chosen, and then leave it alone to do its job. The best way to do this is to set low tempera- tures first, say 18°C, and then turn them up by one degree each day until you are comfortable with the temperatures. You won’t have to adjust the thermostat further. Any adjustments above these settings may waste energy. If your heating system is a boiler with radiators, there will usually be only one programmable room thermostat to control the whole house. But you can have different temperatures in indi- vidual rooms by installing thermostatic radiator valves (TRVs) on individual radiators. If you don’t have TRVs, you should choose a tem- perature that is reasonable for the whole house. If you do have TRVs, you can choose a slightly higher setting to make sure that even the coldest room is comfortable, then prevent any overheat- ing in other rooms by adjusting the TRVs. Programmable room thermostats need a free flow of air to sense the temperature, so they must not be covered by curtains or blocked by furniture. Nearby fires, televisions, wall or table lamps may prevent the thermostat from working properly. GENERAL INFORMATION PROGRAMMABLE THERMOSTATS OPERATING & INSTALLATION INSTRUCTIONS 2 DT10RF PROGRAMMER INSTRUCTION MANUAL 8 716 115 493a (02.2009) 8_716_115_493a 9/2/09 09:45 Page 6

setting adjustment Clock mode Right hand button > moves the pointer to the right, selects and accepts changes Day indicator Flame shows when calling for heat Left hand button < moves pointer to the left for selection Holiday, Manual, Auto, Day mode Time Mode indicator Clock Setting The Digistat Programmable Thermostat is fitted with a real-time clock, which is pre-set at the factory. You will not have to set the time. A special feature of this real-time clock is to automatically update the time during the summer/winter time change removing the need to manually alter the clock. General Operation With the unit in Auto mode (the small arrow to bottom of screen will point to Auto) the temperature can be changed for a short time by using the + or - buttons. Changing the temperature in this way will keep the Programmer set to your new temperature until the next pre-programmed event (at which time it will revert to programmed temperature). The temperature you are setting will flash on the screen. Once temperature is set, the unit will revert to showing the current temperature. The flame indicator will show on the screen if the heating is turned on. NOTE: The temperature displayed is actual room temperature unless adjusting the + or - button when the set temperature is displayed. Once adjustment is complete and after a 5 second delay the display will return to the actual room temperature. Digistat Programmable Thermostat The Digistat Programmer has factory set programs for ON/OFF periods for central heating which are described on the following pages. These factory installed settings can be used without any further programming. DT10RF PROGRAMMER INSTRUCTION MANUAL 8 716 115 493a (02.2009) OPERATING & INSTALLATION INSTRUCTIONS 3 8_716_115_493a 9/2/09 09:45 Page 7

This is a 24-Hour programmable thermostat product (the same program for every day of the week) which allows you to set up to 6 time and temperature events per day. Pre-set Program 1 The following default settings are pre-programmed for your convenience: Every day Event 1 2 3 4 5 6 Time 06:30 08:30 12:00 14:00 16:30 22:30 Temp. 20 16 16 16 21 7 As shown, at 06:30 , the heating will come on to raise the temperature to 20°C. At 08:30, the tem- perature set point is dropped from 20°C down to16°C, it stays at 16°C throughout the day, until 16:30 when the temperature increases to 21°C. The temperature then drops down to a night-set- back temperature of 7°C until 06:30 when the cycle repeats for the next day. To switch the thermostat OFF: Press the + and – simultaneously for 5 seconds until the OFF is displayed. The thermostat and heating system will now be OFF unless the temperature in the controlled space falls below 7°C, the frost protection set point. Please note this does not affect the operation of the domestic hot water where provided. To switch ON the thermostat, press any key to return to auto mode. 5 sec OPERATING & INSTALLATION INSTRUCTIONS 4 DT10RF PROGRAMMER INSTRUCTION MANUAL 8 716 115 493a (02.2009) 8_716_115_493a 9/2/09 09:45 Page 8

1. With the product operating as normal in Auto mode press > twice until the time display is flashing as shown. 2. Use the + or - buttons to adjust the 1st time as required. 3. When the time has been set press > to confirm. The temperature display will now be flashing. 4. Use + or – button to adjust required temperature. NOTE: Small 1 in lower half of screen shows the time period being set. e.g. 1=1st period, 2 = 2nd period etc) 5. When the temperature has been set press > to confirm and move to next time and temperature periods to be adjusted confirming changes by pressing > button (max 6 time periods). 6. To exit press < or > until you return to auto mode with the bottom arrow pointing to auto (as shown). To change temperature for a short period (Override): 1. Press + or - buttons to adjust set temperature. Set temperature flashing as shown. 2 OR PROGRAMMABLE SETTINGS ADJUSTING TIMES & TEMPERATURES OR 1=1st time period 2=2nd time period OR Auto mode indicator OR DT10RF PROGRAMMER INSTRUCTION MANUAL 8 716 115 493a (02.2009) OPERATING & INSTALLATION INSTRUCTIONS 5 8_716_115_493a 9/2/09 09:45 Page 9

2. After 5 seconds the Digistat will start controlling at the selected set point but now displays actual room temperature. Two chevrons indicates override mode. 3. To exit override press > once or wait until next change in the pre-set program (i.e. when period 5, in this case, becomes period 6). To set a constant room temperature (Manual mode): 1. Press < once, the display shows temperature flashing (e.g. 20°C). 2. Press + or - buttons to adjust the temperature as required. The temperature will stop flashing after 5 seconds and start controlling at this temperature. 3. Press > once, to return to auto mode. To set holiday mode: 1. Press < twice, the display shows time flashing. Time periods between 1 to 23(Hr) hours and 1 to 199(d) days can be set. 2. Press + or - buttons to adjust the count down time as required. 2 chevrons indicate override mode Reverts to 1 chevron OR 2 OR Holiday mode indicator OPERATING & INSTALLATION INSTRUCTIONS 6 DT10RF PROGRAMMER INSTRUCTION MANUAL 8 716 115 493a (02.2009) 8_716_115_493a 9/2/09 09:46 Page 10

flashing. 4. Press + or - buttons to adjust temperature and press > to start holiday count down time. Alternatively after 10 seconds the temperature will stop flashing and holiday count down time will start. Display shows count down time and ambient room temperature. 5. To exit the holiday mode press the < or > once, to return to auto. User Options User Options (shown in table on page 8) can be accessed from Auto or Man by pressing < and > simultaneously for 3 seconds. When you have accessed the User Options Menu press > to scroll through selectable options. The settings for each option can be changed by pressing + or - as required. Pressing > accepts the change and moves to the next option. NOTE: To exit User Options press < and > simultaneously for 3 seconds. Alternatively, not pressing any buttons for 2 minutes will cause the Programmer to return to Auto. This figure opposite shows option “01 24” (24 hour clock). Only options that have been accepted by pressing > will be changed. 3 sec DIGISTAT USER OPTIONS DT10RF PROGRAMMER INSTRUCTION MANUAL 8 716 115 493a (02.2009) OPERATING & INSTALLATION INSTRUCTIONS DT10RF PROGRAMMER INSTRUCTION MANUAL 8 716 115 493a (02.2009) OPERATING & INSTALLATION INSTRUCTIONS 7 8_716_115_493a 9/2/09 09:46 Page 11

Min Max Default 01 Change clock 12h/24h 12 24 24 02 Change pre-set program 1 3 1 03 Change number of program events per day 2,4 or 6 6 04 Switch on/off daylight saving time change On Off On 05 Adjust date and time Factory set 06 Change temperature offset °C -5 5 0 07 Restore pre-set program On Off Off 08 Disable OFF function On Off On 09 Access protection lock On Off Off Option 01 Change from 24hr to 12hr clock. 1. Enter user options by pressing < and > simultaneously for 3 seconds. 2. Select option 01 by pressing > until 01 appears. 3. Use + and – keys to select desired option setting, 12 = 12hr and 24 = 24hr. Press > to accept change. Option 02 Change to program 1, 2 or 3. 1. Enter user options by pressing < and > simultaneously for 3 seconds. 2. Select option 02 by pressing > until 02 appears. 3. Use + and – keys to select desired program 1, 2 or 3. 1 = program 1, 2 = program 2, 3 = program 3 etc. Press > to accept change. Preset programs 2 and 3 are shown below: Pre-set Program 2 (Home for lunch) 24 hours At 06:30 the heating raises the temperature to 21°C. At 08:30, the temperature set point is dropped to 16°C, until 12:00 when the heating raises the temperature to 21°C. The temperature stays at 21°C until 14:00 when it drops to 16°C. At 16:30 the heating raises the temperature to 21°C where it stays until 22:30 when the temperature drops down to a night setback temperature of 10°C until 06:30 when the cycle repeats the next day. Option setting Option select Option setting Option select Event 1 2 3 4 5 6 Time 6:30 8:30 12:00 14:00 16:30 22:30 Temperature 21 16 21 16 21 10 OPERATING & INSTALLATION INSTRUCTIONS 8 DT10RF PROGRAMMER INSTRUCTION MANUAL 8 716 115 493a (02.2009) 8_716_115_493a 9/2/09 09:46 Page 12

As you can see, at 06:00, the heating will come on to raise the temperature to 21°C. At 08:30, the temperature set point is dropped to 19°C, it stays at 19°C until 12:00 when the heating comes on to raise the temperature to 21°C. The temperature stays at 21°C until 14:00 when it drops to 19°C. At 17:30 the heating comes on to raise the temperature to 21°C where it stays until 22:30 when the temperature drops down to a night setback temperature of 16°C until 06:00 when the cycle repeats the next day. Option 03 How to change the number of program events per day. 1. Enter user options by pressing < and > simultaneously for 3 seconds. 2. Select option 03 by pressing > until 03 appears. 3. Use + and – keys to select option. 2 = 2 time / temp events per day 4 = 4 time / temp events per day 6 = 6 time / temp events per day. Press > to accept change. Option 04 How to switch on/off the automatic summer / winter time change. Twice a year the actual time is automatically changed to keep it in line with the summer / winter time change. Default setting is On. If you wish to disable / enable this feature: 1. Enter user options by pressing < and > simultaneously for 3 seconds. 2. Select option 04 by pressing > until 04 appears. 3. Press – or + key to display Off or On as desired. Press > to accept change. Event 1 2 3 4 5 6 Time 6:00 8:30 12:00 14:00 17:30 22:30 Temperature 21 19 21 19 21 16 Option select Program setting Option select On/Off setting DT10RF PROGRAMMER INSTRUCTION MANUAL 8 716 115 493a (02.2009) OPERATING & INSTALLATION INSTRUCTIONS 9 8_716_115_493a 9/2/09 09:46 Page 13

The DT10RF Programmer comes with a pre-set clock, which also automatically adjusts for daylight saving time changes. It is activated automatically on 1st installation. There should be no need to change these settings, however, should you wish to, it can be done in Option 05. Option 05 How to adjust date and time. 1. Enter user options by pressing < and > simultaneously for 3 seconds. 2. Select option 05 by pressing > until 05 appears. 3. To access the year press > once and the year selection is displayed. Use the + or - key to select the required year and press > to accept the change. The month selection is now displayed. 4. Use the + or - key to select the required month and press > to accept the change. The day selection is now displayed. 5. Use the + or - key to select the required day and press > to accept the change. The time selection is now displayed. 6. Use the + or - key to select the required time and press > to accept the change. Option 6 is now displayed. OPERATING & INSTALLATION INSTRUCTIONS DT10RF PROGRAMMER INSTRUCTION MANUAL 8 716 115 493a (02.2009) 10 8_716_115_493a 9/2/09 09:46 Page 14

through” using the > key before option 6 can be accessed Option 06 How to change temperature offset. The temperature displayed on the thermostat may not match that of other temperature measuring devices in the controlled space, because of its location. The displayed temperature may be offset to bring it in line with other devices. 1. To adjust the temperature, enter the user options by pressing < and > simultaneously for 3 seconds. 2. Select option 06 by pressing > until 06 appears. 3. The temperature may be offset by +/- 5 degrees by pressing the + and – keys. Press > to accept the desired change. Option 07 How to restore the built in time temperature programs. NOTE: Switching this option on will delete any user changes to the preset programs. 1. Enter the user options by pressing < and > simultaneously for 3 seconds. 2. Select option 07 by pressing > until 07 appears. 3. Use + and – keys to select desired option. Off = current programs retained. On = restore factory program settings. Press > to select the desired change. The option 07 display automatically reverts back to off. Option 08 How to disable the OFF function. 1. To disable the Off function, enter user options by pressing < and > simultaneously for 3 seconds. 2. Select option 08 by pressing > until 08 appears. 3. Use + or – keys to select Off. Press > to accept change. It is now not possible to switch the Digistat Off using the + and- keys as previously described. To enable the Off function return to option 08 and select On. Press > to accept change. Option select On/Off setting Option select On/Off setting DT10RF PROGRAMMER INSTRUCTION MANUAL 8 716 115 493a (02.2009) OPERATING & INSTALLATION INSTRUCTIONS 11 8_716_115_493a 9/2/09 09:46 Page 15

Lock. The access protection lock allows you to lock the Digistat Optimiser so that it cannot have any adjustments. The default is Off mode allowing you to adjust the Digistat. 1. To Lock the Digistat settings enter the user options by pressing < and > simultaneously for 3 seconds. 2. Select option 09 by pressing > until 09 appears. 3. Use + or – keys to select On. Press > to accept. Once the User Options Menu is exited all buttons will be locked. 4. To switch off the Protection Lock enter the user options by pressing < and > simultaneously for 3 seconds. 5. Change to Off. Press > to accept. Once the User Menu is exited all buttons will be free to adjust. NOTE: To exit User Options press < and > simultaneously for 3 seconds. Together On/Off setting 3 sec Special Note: The following only applies when the Intelligent delayed start feature is enabled. Ask your installer for details When the delay period is operating indicated by the flame symbol flashing, pressing any button returns the DT10RF Programmer to auto mode allowing normal button operation until the next time/temperature event, when it will resume the delay start mode or follows the Holiday, Manual, Override or Off modes as selected. Changes to the installer options and pre-set programmes must be made with the flame symbol not flashing What is Intelligent delayed start. The Intelligent Delayed Start is an energy saving feature which automatically reduces the warm up time for the heating system. As the weather becomes milder, Intelligent Start will delay the heating start times so that the fuel is not wasted bringing the room up to temperature earlier than necessary. NOTE: See page 28 for further information and set up details. OPERATING & INSTALLATION INSTRUCTIONS DT10RF PROGRAMMER INSTRUCTION MANUAL 8 716 115 493a (02.2009) 12 8_716_115_493a 9/2/09 09:46 Page 16

heat ON light Hot water pre-heat select button, moves the mode indicator up and down to select and accept changes Hot water pre- heat advance button, when pressed brings forward next ON/OFF period. Press to accept each program setting Setting clock, date, time, program and holiday function +/- changes ON/OFF times Modes DT10RF Receiver Programmer The Programmer has factory set programs for ON/OFF periods for hot water pre-heat, which are described on the following pages. These factory installed settings can be used without any further programming. This section also details how to program the DT10RF Receiver with new weekday and weekend times to suit your lifestyle requirements. How to set the clock, time and date, is also given, but should not require adjustment as these are factory set. A holiday function is also provided, where you can set the number of days that you are away on holiday. The boiler will provide frost protection for those number of days. After that set number of days the boiler will revert to the normal operating program, ready for your return DT10RF PROGRAMMER INSTRUCTION MANUAL 8 716 115 493a (02.2009) OPERATING & INSTALLATION INSTRUCTIONS 13 8_716_115_493a 9/2/09 09:46 Page 17

� off = constantly OFF �timed = up to 3 ON and 3 OFF time periods as programmed �once = ON from first ON until third OFF time period as programmed The default ON/OFF periods pre-pro grammed for hot water pre-heat are shown in the table opposite. �on = constantly ON 2. Press “advance” button: ON = hot water pre-heat light on (hot water pre-heat stays on until next off time period) OFF = hot water pre-heat light off (hot water pre-heat stays off until next on time period) NOTE: Advance has no effect with the constantly on or off selected on the receiver. DT10RF RECEIVER OPERATING CONTROLS OPERATING & INSTALLATION INSTRUCTIONS DT10RF PROGRAMMER INSTRUCTION MANUAL 8 716 115 493a (02.2009) 14 8_716_115_493a 9/2/09 09:46 Page 18

Hot Water pre-heat are shown in the table opposite. The factory installed settings can be used without any further programming of the receiver. The date and time are pre-programmed and should not require adjustment. If you need to restore the factory pre-set program times then: Press the + and - buttons together, for at least 3 seconds, to restore the default program times. NOTE: Two ON/OFF periods can be used instead of three, by setting the second ON/OFF periods to 12:00 as shown in the default program table. One ON/OFF period can be achieved by setting the second and third ON/OFF periods to the same time. See RECEIVER PROGRAMMABLE SETTINGS if changes are required to the clock time or pre- programmed settings. 1st 1st 2nd 2nd 3rd 3rd ON OFF ON OFF ON OFF Hot Water: MON to FRI Time 06:30 08:30 12:00 12:00 16:30 22:30 SAT & SUN Time 07:00 09:00 12:00 12:00 16:00 23:00 DT10RF RECEIVER PRE-SET PROGRAMS DT10RF PROGRAMMER INSTRUCTION MANUAL 8 716 115 493a (02.2009) OPERATING & INSTALLATION INSTRUCTIONS 15 8_716_115_493a 9/2/09 09:46 Page 19

1. Press set? until SET and PROG? are shown in the display. Press OK to select PROG to continue with programming. 2. Press OK to select MON-FRI. 3. Press OK to select ON time. NOTE: Speed up the display by holding down the + or - buttons. 4. Press + or - to change the ON time. 5. Press set? to set the ON time and select the OFF time. 6. Press + or - to change the OFF time. 7. Press set? to set the OFF time and select the next ON time. Repeat operations 4 to 7 to set the second and third ON/OFF times. NOTE: After pressing set? for the third hot water pre-heat OFF time the display shows SET MON ...see next page DT10RF RECEIVER PROGRAMMABLE SETTINGS OPERATING & INSTALLATION INSTRUCTIONS DT10RF PROGRAMMER INSTRUCTION MANUAL 8 716 115 493a (02.2009) 16 8_716_115_493a 9/2/09 09:46 Page 20

NOTE: If you do not require individual weekday times, then press set? until SET SAT-SUN is displayed and continue on the next page. If you do not wish to change the setting for the day displayed, then press set? until the first day you want to change is displayed. 1. Press OK to select weekday. 2. Press OK to select first ON time. NOTE: Speed up the display by holding down the + or - buttons. 3. Press + or - to change the ON time. 4. Press set? to set the ON time and select the OFF time. 5. Press + or - to change the OFF time. 6. Press set? to set the OFF time and select the next ON time. Repeat operations 3 to 6 to set the second and third ON/OFF times. NOTE: After pressing set? for the third OFF time, SET and the next weekday are displayed after completing the steps above for FRI the display shows SET SAT-SUN. see next page.... DT10RF RECEIVER PROGRAMMABLE SETTINGS DT10RF PROGRAMMER INSTRUCTION MANUAL 8 716 115 493a (02.2009) OPERATING & INSTALLATION INSTRUCTIONS 17 8_716_115_493a 9/2/09 09:46 Page 21

1. Press OK to select weekend. NOTE: Speed up the display by holding down the + or - buttons. 2. Press + or - to change the ON time. 3. Press set? to set the ON time and select the OFF time. 4. Press + or - to change the OFF time. 5. Press set? to set the OFF time and select the next ON time. Repeat operations 2 to 5 to set the second and third ON/OFF times. NOTE: After pressing set? for the third OFF time, SET SAT are displayed.... If you do not require individual weekend times, then press set? until the normal display is resumed. OPERATING & INSTALLATION INSTRUCTIONS DT10RF PROGRAMMER INSTRUCTION MANUAL 8 716 115 493a (02.2009) 18 8_716_115_493a 9/2/09 09:46 Page 22

NOTE: If you do not require individual weekend times, then press set? until the normal dis- play is shown. If you do not wish to change the setting for SAT, then press set? until the normal display is shown. 1. Press OK to select the day displayed. NOTE: Speed up the display by holding down the + or - buttons. 2. Press + or - to change the ON time. 3. Press set? to set the ON time and select the OFF time. 4. Press + or - to change the OFF time. 5. Press set? to set the OFF time and select the next ON time. Repeat operations 2 to 5 to set the second and third ON/OFF times. NOTE: After pressing set? for the third hot water pre-heat off time for SAT, the display will show SET SUN. Press OK to set SUN or press set? until the display returns to normal mode. Holiday settings 1. Press the set? button until SET and HDAY are displayed. 2. Press OK, the display shows 00. 3. Press + or - to set the number of days you require the system to be off. 4. Press set? then HDAY is shown in the display and no demand for heating will be made from the programmer. The programmer will return to normal after the set number of days. To cancel the Holiday setting and return to normal operation, press any button. NOTE: The programmer counts each pass through midnight as a day. For example, if you did not want heating from Saturday morning until Tuesday morning, set for three days. DT10RF PROGRAMMER INSTRUCTION MANUAL 8 716 115 493a (02.2009) OPERATING & INSTALLATION INSTRUCTIONS 19 8_716_115_493a 9/2/09 09:46 Page 23

1. Press the set? button until SET and CLOCK are displayed. 2. Press OK. 3. Press + to switch between 24hr and 12hr display. 4. Press set? to set the clock and the hours display flashes. 5. Press + or - to set the correct hour. NOTE: Speed up the display by holding down the + or - buttons. 6. Press the set? button to accept the correct hour and minutes display flashes. 7. Press + or - to set the correct minutes. 8. Press the set? button to accept the correct minutes. Now SET and DATE will be displayed. NOTE: If the day displayed is incorrect the date needs resetting. To change the date, refer to SETTING THE DATE on the next page. If you do not wish to change the date, press set? to return to the normal display. DT10RF RECEIVER PROGRAMMABLE SETTINGS OPERATING & INSTALLATION INSTRUCTIONS DT10RF PROGRAMMER INSTRUCTION MANUAL 8 716 115 493a (02.2009) 20 8_716_115_493a 9/2/09 09:46 Page 24

NOTE: If the day displayed is incorrect, the date needs resetting as follows: 1. Press the set? button until SET and DATE are displayed. 2. Press the OK button once, the year will flash on the display. 3. Press + or - to correct the year. 4. Press the set? button and the month will flash on the display. 5. Press + or - to correct the month. 6. Press the set? button and the day will flash on the display. 7. Press + or - to correct the day. 8. Press the set? button, the DLS and ON will flash on the display. 9. Press + or - to set for ON or OFF 10. Press set? twice to return to the normal display. NOTE: DLS = Day Light Saving time DT10RF PROGRAMMER INSTRUCTION MANUAL 8 716 115 493a (02.2009) OPERATING & INSTALLATION INSTRUCTIONS 21 8_716_115_493a 9/2/09 09:46 Page 25

DO NOT TOUCH THE ELECTRICAL COMPONENTS OR CIRCUITS CAUTION: ISOLATE THE MAINS ELECTRICITY SUPPLY BEFORE STARTING ANY WORK AND OBSERVE ALL RELEVANT SAFETY PRECAUTIONS 1. Remove the boiler outer casing and control panel fascia to gain access to the heatronic control panel. Release the securing screws. Pull the cover panel upwards to remove. Grip the tab and pull upwards to disengage clips, pull forward to remove blanking plate or existing programmer. 2. Align connector pins into the sockets on the PCB and push fully home. Feed the ribbon cable into the recess. 3. Align the programmer and locate the clips, push into the slots then downwards to secure. Locate the cover panel in place and secure with the screw. Replace fascia cover and outer casing before switching on the electrical supply and boiler. Switch boiler on when completed. Refer to the User Instructions section for details of pre-set and setting programs. Clips Panel Screw Tab Blanking plate Recess Connector plug Receiver Ribbon cable Clips Programmer Screw OBSERVE ELECTRO-STATIC DISCHARGE PRECAUTIONS. DO NOT TOUCH THE PCB CIRCUIT Tab NOTE: THIS ACCESSORY MUST BE FITTED BY A COMPETENT PERSON. FAILURE TO COMPLY COULD LEAD TO PROSECUTION. OPERATING & INSTALLATION INSTRUCTIONS DT10RF PROGRAMMER INSTRUCTION MANUAL 8 716 115 493a (02.2009) 22 8_716_115_493a 9/2/09 09:46 Page 26

SETTING UP THE RF LINK Receiver set up: After initial start up, the colon, CH and antenna symbols should be flashing on the display. 1. Press the set? button 4 times 2. Press the OK button once 3. Press the set? button 4 times; Lrn and OFF should be displayed 4. Press the + button so the display shows ON and a flashing antenna symbol. The learn mode is now ready to receive a signal from the transmitter during the next two minutes. Transmitter set up: 1. Take the Digistat Programmer unit and stand near the boiler. 2. Remove the battery cover and fit the batteries. How to fit the batteries Remove the battery cover using a coin. Insert 2 x 1.5V (AA) Alkaline batteries ensuring correct orienta- tion. Replace the battery cover pressing fully home. Transmitter battery compartment Digistat DT10RF PROGRAMMER INSTRUCTION MANUAL 8 716 115 493a (02.2009) OPERATING & INSTALLATION INSTRUCTIONS 23 8_716_115_493a 9/2/09 09:46 Page 27

SETTING UP THE RF LINK Signal strength indicators Transmitter code (may be different) LED indicator shows different colour depending on signal strength (see table below) 3. The symbols on the receiver will stop flashing and the display will show ‘SSI, Antenna and ON’. 4. Press ‘SET’ and the display will show ‘SSI and Antenna’. 5. After a few seconds the display will show ‘- - -’. 6. Remove the batteries from the transmitter and wait for the display to fade. Press and hold the ‘+’ button while re-inserting the batteries and keep the button depressed until the display shows ‘rF’. The transmitter is now in constant transmission mode enabling it to be correctly positioned within the home. 7. The receiver display will now show the ‘learnt’ transmitter code and the antenna’ as well as the signal strength as indicated by the chevrons on the right hand side of the display. 8. Place the transmitter in the desired final position and return to the boiler to check the receiver display. The ideal transmitter position will result in the receiver display showing 4 chevrons and the LED will be green. For siting advice please refer to “Positioning RF room thermostats” on page 25. 9. If the LED is red or no LED is showing and the display indicates 1 or 2 chevrons, the transmitter will need to be re-positioned until the LED changes to amber or green and 3 or 4 chevrons are indicated on the display. NOTE: If there is no LED and the display shows ‘- - -’, there is no signal being received at all from the transmitter. Transmission will resume once the transmitter is re-positioned in a part of the house where an amber or green LED and 3 or 4 chevrons are achieved. 10. Once you are happy that, when in the desired location, the transmitter is sending a good signal to the receiver i.e. amber or green and 3 or 4 chevrons, the transmitter can be fixed to the wall. LED Indication Chevrons RF Strength Green Amber Red None 4 3 2 1 Very strong Strong Weak Very weak OPERATING & INSTALLATION INSTRUCTIONS DT10RF PROGRAMMER INSTRUCTION MANUAL 8 716 115 493a (02.2009) 24 8_716_115_493a 9/2/09 09:46 Page 28

MOUNTING THE DIGISTAT Positioning RF room thermostats The Digistat is a radio frequency device which is very flexible for positioning as there is no need for hard wiring to the appliance. The device should be mounted in a open area, no closer than 30cm from metal objects, including wall boxes. Mount the Digistat on a wall which is not subject to direct sunlight or draughts, preferably on an inside wall, 1.5 metres above the floor. The Digistat must also not be directly influenced by radiators or other appliances giving off heat. 1. Remove the front cover using a flat screwdriver and separate from back plate. Mounting the digistat Digistat To cancel signal strength mode: 1. Remove the batteries from the transmitter to cancel the constant transmission. 2. After a few seconds the receiver display will show ‘---’ . 3. Press ‘OK’ on the receiver display and the display will return to the time with the ‘CH and Antenna’ flashing. 4. Re-insert the batteries into the transmitter and the RF link will be re-established. 2. Fix the back plate directly onto the wall using suitable wall plugs and screws. DT10RF PROGRAMMER INSTRUCTION MANUAL 8 716 115 493a (02.2009) OPERATING & INSTALLATION INSTRUCTIONS 25 8_716_115_493a 9/2/09 09:46 Page 29

TO CHECK PREVIOUSLY INSTALLED UNIT 3. Replace the front cover by locating in position and pushing fully onto the back cover. To check signal strength on previously installed and paired units : 1. Press the ‘set’ button 4 times. 2. Press ‘OK’ once. 3. Press the ‘set’ button 5 times. The display will show ‘SSI and OFF’. 4. Press the ‘+’ button so that the display shows ‘SSI, Antenna and ON’. 5. Press the ‘set’ button so the display shows ‘SSI and Antenna’. 6. After a few seconds the display will show ‘---’. 7. Remove the batteries from the transmitter and wait until the display has faded away. 8. Press and hold the ‘+’ button on the transmitter while re-inserting the batteries and keep the button depressed until the display shows ‘rF’ . OPERATING & INSTALLATION INSTRUCTIONS DT10RF PROGRAMMER INSTRUCTION MANUAL 8 716 115 493a (02.2009) 26 8_716_115_493a 9/2/09 09:46 Page 30

TO CHECK PREVIOUSLY INSTALLED UNIT Signal strength indicators Transmitter code (may be different) LED indicator shows different colour depending on signal strength (see table right) 9. Check the receiver LED and chevrons to determine the signal strength now being received. To cancel signal strength mode: 1. Remove the batteries from the transmitter to cancel the constant transmission. 2. After a few seconds the receiver display will show ‘---’ . 3. Press ‘OK’ on the receiver display and the display will return to the time with the ‘CH and Antenna’ flashing. 4. Re-insert the batteries into the transmitter and the RF link will be re-established. During normal operation The LED on the receiver will flash red, approximately every 5 minutes. This denotes that a radio signal is being received from the transmitter. LED Indication Chevrons RF Strength Green Amber Red None 4 3 2 1 Very strong Strong Weak Very weak DT10RF PROGRAMMER INSTRUCTION MANUAL 8 716 115 493a (02.2009) OPERATING & INSTALLATION INSTRUCTIONS 27 8_716_115_493a 9/2/09 09:46 Page 31

as shown in the table below, enter the Installer Option Menu from Auto mode by pressing: < and + simultaneously for 5 seconds. Pressing < and + again for 5 seconds will exit the Menu and return to Auto mode. Once the Installer Options screen has been selected, the < and > buttons allow you to scroll through the Menu (shown below). The + and - allow you to change values. Once a value has been changed pressing > before exiting the Menu will save the new setting. (The figure shows Option 02 OFF). 5 sec Installer Options Function Select Option Default 02 Freeze protection On Off On 04 Low Set Point C 5 High Limit 5 Option 02 - Freeze Protection Freeze protection will switch on the heating if the room temperature falls to 5°C and will then control the temperature at 7°C even if the Digistat is in OFF mode. The Freeze Protection default is ON. To switch off the Freeze Protection mode enter the Installer Options Menu (Refer to Installer Options 02) and change to OFF. Press > to accept. Option 04 & 05 - Low and High Limit set points. The user temperature set points defaults are High 32°C and Low 5°C, to change these limits enter the Installer Options Menu (Refer to Installer Options 04 & 05). Option 06 - Intelligent Delayed Start (Energy saving feature). The Intelligent Delayed Start is an energy saving feature which automatically reduces the warm up time for the heating system. Installer Options Function Select Option Default 05 High Set Point C Low Limit 32 32 Installer Options Function Select Option Default 06 Delayed Start (Energy saving feature On Off Off OPERATING & INSTALLATION INSTRUCTIONS DT10RF PROGRAMMER INSTRUCTION MANUAL 8 716 115 493a (02.2009) 28 8_716_115_493a 9/2/09 09:46 Page 32

earlier than the time you want the property to reach the set temperature. Intelligent Start will delay that start time, by an amount that it has calculated based on the actual and set temperature. As the weather becomes milder, the start time is delayed, so that fuel is not wasted bringing the room up to temperature earlier than necessary. The Digistat calculates approximately 10 minutes to raise the temperature by 1°C, up to a maximum of 6°C. Note: Intelligent Delayed Start only applies in Auto mode. Intelligent Delayed Start default is in OFF mode. To switch ON Intelligent Delayed Start enter the Installer Options Menu (see Installer Options 06). Note: The Intelligent Delayed start option is not suitable for underfloor application. Ensure Installer option 06 is set to OFF before final commissioning for underfloor application. Special Note: If the Intelligent delayed start feature is enabled, (Off changed to On in Installer option 06), please inform the end user of this feature. The following special note has been added to the user instruction to explain the adjustment requirement: When the delay period is operating indicated by the flame symbol flashing, pressing any button returns the Digistat to auto mode allowing normal button operation until the next time/ temperature event, when it will resume the delay start mode or follows the Holiday, Manual, Override or Off modes as selected. Changes to the installer options and pre-set pro- grammes must be made with the flame symbol not flashing. Option 10 - System Protection In some heating systems there may be a requirement to protect the system by operating it once a day, for a given period. Installer Options Function Select Option Default 10 System protection On Off Off DT10RF PROGRAMMER INSTRUCTION MANUAL 8 716 115 493a (02.2009) OPERATING & INSTALLATION INSTRUCTIONS 29 8_716_115_493a 9/2/09 09:46 Page 33

operated for a period as shown in system protection time (mins). System protection time is every day at 10.00am. System protection default is OFF. To enable the system protection mode enter the Installer Options Menu (Refer to Installer Option 10). Option 11 - System Protection time (mins). System protection time can be set between 1 and 5 minutes (default 3 minutes). To change this once a day on time enter the Installer Options Menu (Refer to Installer Option 11). 11 System protection time (Mins) 1 5 3 How do I know when to change the batteries. When the batteries start to run low a battery icon will flash in the display, to indicate “low battery” during this time the Digistat will function normally. Replace with 2 x 1.5V (AA) Alkaline batteries. When the battery icon alone is shown in the display, the batteries are completely exhausted and the Digistat will cease to function. Re-activate by replacing the batteries. The RF link will automatically be re-established. How to replace the batteries Remove the battery cover using a coin. Replace the spent batteries with 2 x 1.5V (AA) Alkaline batteries ensuring correct orientation. Replace the battery cover pressing fully home. OPERATING & INSTALLATION INSTRUCTIONS DT10RF PROGRAMMER INSTRUCTION MANUAL 8 716 115 493a (02.2009) 30 8_716_115_493a 9/2/09 09:46 Page 34

Programmer) requires no maintenance. The outer casing can be wiped clean using a dry cloth. DO NOT use polish or detergents. These units can not be serviced. Should the existing unit fail to function correctly, check: �Receiver times and program settings are correct RF signal link is set up �Transmitter batteries are the correct type, fitted correctly and are not exhausted. Fit new batteries if in doubt. DT10RF Receiver Part Number: 8 716 106 667 0 DIGISTAT / DT10RF RECEIVER MAINTENANCE Digistat Programmer Part number 8 716 114 461 0 DT10RF PROGRAMMER INSTRUCTION MANUAL 8 716 115 493a (02.2009) OPERATING & INSTALLATION INSTRUCTIONS 31 8_716_115_493a 9/2/09 09:46 Page 35

Cotswold Way, Warndon, Worcester WR4 9SW. Tel. 01905 754624 Fax. 01905 754619 worcester-bosch.co.uk Worcester, Bosch Group is a brand name of Bosch Thermotechnology Ltd. 8 716 115 493a (02.2009) 06515056001 ISSB CONTACT INFORMATION WORCESTER, BOSCH GROUP: TECHNICAL: 08705 266241 SERVICE: 08457 256206 SPARES: 01905 752571 LITERATURE: 01905 752556 TRAINING: 01905 752526 SALES: 01905 752640 WEBSITE: worcester-bosch.co.uk WEBSITE (EIRE): worcester-bosch.ie 8_716_115_493a 9/2/09 09:46 Page 36