Panasonic KX-HNB600 Systems Setup Manual

Home Network System HUB Model No. KX-HNB600 Thank you for purchasing a Panasonic product. This document explains how to configure the hub and access it using a mobile device. These steps must be followed before you can use the system. For details about how to use the system, refer to the User’s Guide (page 17). Please read this document before using the unit and save it for future reference. For assistance, please contact us at 1-800-272-7033 or visit our Web site: http://shop.panasonic.com/support for customers in the U.S.A. Please register your product: http://shop.panasonic.com/support Printed in China HNB600_(en_en)_0124_ver.201.pdf 1 2017/01/25 10:22:31

Important Information About this system .........................................6 For your safety .............................................6 Important safety instructions ........................7 Security cautions ..........................................7 For best performance ...................................8 Other information .........................................8 Setup Part names and functions ..........................10 LED indicator ..............................................10 Connections ...............................................11 Wi-Fi® settings ...........................................12 Registering another mobile device .............15 Registering other devices to the hub ..........15 Appendix Wireless communication range (DECT) .....17 Accessing the User’s Guide .......................17 Wall mounting ............................................18 Specifications .............................................20 Open source software notice .....................20 Software information ..................................20 FCC and other information .........................21 Customer services .....................................23 Limited Warranty (ONLY FOR U.S.A.) .......24 2 Table of Contents HNB600_(en_en)_0124_ver.201.pdf 2 2017/01/25 10:22:34

Quantity A AC adaptor/PNLV236-0Y 1 B Telephone line cord/PQJA10075Z 1 C Wall mounting adaptor/PNKL1049Z1 1 A B C Additional accessories microSD card (not supplied) A commercially-available microSD card must be inserted into the hub in order to record images from cameras. The following types of microSD cards are supported. R microSD / SDHC card: Up to 32 GB Other information R Design and specifications are subject to change without notice. R The illustrations in these instructions may vary slightly from the actual product. Trademarks R microSDHC Logo is a trademark of SD-3C, LLC. R iPhone and iPad are registered trademarks of Apple Inc. R iPad mini is a trademark of Apple Inc. R Android and Google Play are registered trademarks or trademarks of Google Inc. R Microsoft, Windows, and Internet Explorer are either registered trademarks or trademarks of Microsoft Corporation in the United States and/or other countries. R Wi-Fi®, WPA™, and WPA2™ are registered trademarks or trademarks of Wi-Fi Alliance®. R All other trademarks identified herein are the property of their respective owners. Notice R The hub supports microSD and microSDHC memory cards. In this document, the term “microSD card” is used as a generic term for any of the supported cards. For assistance, please visit http://shop.panasonic.com/support 3 Introduction HNB600_(en_en)_0124_ver.201.pdf 3 2017/01/25 10:22:34

The Panasonic Home Network System is a wireless system that lets you create a powerful network of devices, such as cameras, sensors, and smart plugs, and control them all with an easy-to-use app. Compatible devices are explained below. For information about the Home Network app, refer to the User’s Guide (page 17). The maximum number of devices for each device type is listed below. Digital Cordless Handset (KX-HNH100: 6 max.*1) R Makes and receives calls using your home landline R Can be used to change the system’s arm mode R Displays system status R Receives notification when the sensors are triggered Indoor Camera (KX-HNC210: 4 max.*2) R Full-color camera and built-in microphone for live monitoring and recording R Built-in visual sensor, audio sensor, and temperature sensor can be used to trigger other actions (camera recording, turning on a light, etc.) R Built-in microphone and speaker for two-way communication Outdoor Camera (KX-HNC600: 4 max.*2) R Full-color camera with built-in microphone for live monitoring and recording R Built-in visual sensor and infrared sensor can be used to trigger other actions (camera recording, turning on a light, etc.) R Built-in microphone and speaker for two-way communication R Splash proof design for permanent, outdoor installation Window/Door Sensor (KX-HNS101: 50 max.*2) R Detects when the corresponding window or door is opened R Can be used to trigger other events (camera recording, turning on a light, etc.) Motion Sensor (KX-HNS102: 50 max.*2) R Detects motion in the surrounding area R Can be used to trigger other events (camera recording, turning on a light, etc.) 4 For assistance, please visit http://shop.panasonic.com/support Introduction HNB600_(en_en)_0124_ver.201.pdf 4 2017/01/25 10:22:34

R Can be turned on and off using the handset or Home Network app, when triggered by a sensor, or according to a schedule R Built-in overcurrent and overwattage detection for added peace of mind R Power consumption is logged for your reference *1 Optional handsets may be a different color from that of the handset supplied as part of a pre-configured bundle. *2 A total of 6 cordless handsets, 4 cameras, and 50 other devices (motion sensors, window/ door sensors, smart plugs, etc.) can be registered to the hub. The Home Network System product lineup is growing! You can look forward to new devices that will make your Home Network System even more useful and convenient. For information about the latest devices and bundles, visit the website below. http://shop.panasonic.com/support Mobile devices Your mobile devices: 8 max.*1 You can expand the system by installing the Home Network app on your mobile devices (smartphones, tablets, etc.) and registering your mobile devices to the hub. See page 12 for more information about the Home Network app. Note: R You must configure the hub’s Wi-Fi settings before you can use the app. *1 8 mobile devices can be registered to the hub, however, only the first 4 can use phone features. For assistance, please visit http://shop.panasonic.com/support 5 Introduction HNB600_(en_en)_0124_ver.201.pdf 5 2017/01/25 10:22:34

R This system is an auxiliary system; it is not designed to provide complete protection from property loss. Panasonic will not be held responsible in the event that property loss occurs while this system is in operation. R The system’s wireless features are subject to interference, therefore functionality in all situations cannot be guaranteed. Panasonic will not be held responsible for injury or damage to property that occurs in the event of wireless communication error or failure. For your safety To prevent severe injury and loss of life/ property, read this section carefully before using the product to ensure proper and safe operation of your product. WARNING Power connection R Use only the power source marked on the product. R Do not overload power outlets and extension cords. This can result in the risk of fire or electric shock. R Completely insert the AC adaptor/power plug into the power outlet. Failure to do so may cause electric shock and/or excessive heat resulting in a fire. R Regularly remove any dust, etc. from the AC adaptor/power plug by pulling it from the power outlet, then wiping with a dry cloth. Accumulated dust may cause an insulation defect from moisture, etc. resulting in a fire. R Unplug the product from power outlets if it emits smoke, an abnormal smell, or makes an unusual noise. These conditions can cause fire or electric shock. Confirm that smoke has stopped emitting and contact us at http://shop.panasonic.com/support R Unplug from power outlets and never touch the inside of the product if its casing has been broken open. Danger of electric shock exists. R Never touch the plug with wet hands. Danger of electric shock exists. R Do not connect non-specified devices. Installation R To prevent the risk of fire or electrical shock, do not expose the product to rain or any type of moisture. R Do not place or use this product near automatically controlled devices such as automatic doors and fire alarms. Radio waves emitted from this product may cause such devices to malfunction resulting in an accident. R Do not allow the AC adaptor or telephone line cord to be excessively pulled, bent or placed under heavy objects. R Keep small parts, such as microSD cards, out of the reach of children. There is a risk of swallowing. In the event they are swallowed, seek medical advice immediately. Operating safeguards R Unplug the product from power outlets before cleaning. Do not use liquid or aerosol cleaners. R Do not disassemble the product. R Do not spill liquids (detergents, cleansers, etc.) onto the telephone line cord plug, or allow it to become wet at all. This may cause a fire. If the telephone line cord plug becomes wet, immediately pull it from the telephone wall jack, and do not use. R Never put metal objects inside the product. If metal objects enter the product, turn off the circuit breaker and contact an authorized service center. Medical R Consult the manufacturer of any personal medical devices, such as pacemakers or hearing aids, to determine if they are adequately shielded from external RF (radio frequency) energy. DECT features operate between 1.92 GHz and 1.93 GHz with a peak transmission power of 115 mW. Wi-Fi features operate between 2.412 GHz 6 For assistance, please visit http://shop.panasonic.com/support Important Information HNB600_(en_en)_0124_ver.201.pdf 6 2017/01/25 10:22:35

power of 100 mW. R Do not use the product in health care facilities if any regulations posted in the area instruct you not to do so. Hospitals or health care facilities may be using equipment that could be sensitive to external RF energy. CAUTION Installation and location R Never install wiring during a lightning storm. R Never install telephone line jacks in wet locations unless the jack is specifically designed for wet locations. R Never touch uninsulated telephone wires or terminals unless the telephone line has been disconnected at the network interface. R Use caution when installing or modifying telephone lines. R The AC adaptor is used as the main disconnect device. Ensure that the AC outlet is installed near the product and is easily accessible. R This product is unable to make calls when: – there is a power failure. – when the cordless handset or mobile device’s batteries need recharging or have failed. Important safety instructions When using your product, basic safety precautions should always be followed to reduce the risk of fire, electric shock, and injury to persons, including the following: 1. Do not use this product near water for example, near a bathtub, washbowl, kitchen sink, or laundry tub, in a wet basement or near a swimming pool. 2. Avoid using a telephone (other than a cordless type) during an electrical storm. There may be a remote risk of electric shock from lightning. 3. Do not use the telephone to report a gas leak in the vicinity of the leak. 4. Use only the power cord indicated in this document. SAVE THESE INSTRUCTIONS Security cautions Take appropriate measures to avoid the following security breaches when using this product. – Leaks of private information – Unauthorized use of this product – Unauthorized interference or suspension of the use of this product Take the following measures to avoid security breaches: R Configure the wireless router that connects your mobile device to this product to use encryption for all wireless communication. R You may be vulnerable to security breaches if the unit is used with the login password, disarm code, or PIN code, or other settings at their defaults values. Configure your own values for these settings. R Do not use passwords that could be easily guessed by a third party. If you keep a record of your passwords, protect that record. Change passwords regularly. R If you lose your mobile device, change the password used to access this product. R If you enable the product’s auto login feature, enable the screen lock or similar security feature on your mobile device. R Take care when performing important security related operations such as deleting MAC address, unit IDs, etc. R To prevent disclosure of personal information, enable the screen lock or similar security feature on your mobile device. R When submitting the product for repair, make a note of any important information stored in the product, as this information may be erased or changed as part of the repair process. R Before handing the product over to a third party for repair or other purposes, perform a factory data reset to erase any data For assistance, please visit http://shop.panasonic.com/support 7 Important Information HNB600_(en_en)_0124_ver.201.pdf 7 2017/01/25 10:22:35

microSD card. Use only trusted repair services authorized by Panasonic. R Before disposing of the product, perform a factory data reset to erase any data stored in the product. Remove and erase the microSD card. R If your mobile device will no longer be used with the product, delete your mobile device’s registration from the product and delete the corresponding app from your mobile device. R If this product experiences a power outage, its date and time setting may become incorrect. In this case, the date and time setting will be automatically corrected when your mobile device and this product are connected to the same wireless network. Additionally, note the following. R Multiple hubs cannot be used on the same network. R Only one mobile device can access this product while away from home. If a second mobile device connects to this product while away from home, the first mobile device is disconnected. R Communications may be interrupted depending on network conditions and wireless signal quality. R This product may be used in ways that violate the privacy or publicity rights of others. You are responsible for the ways in which this product is used. For best performance Hub location/avoiding noise The hub and other compatible Panasonic devices use radio waves to communicate with each other. R For maximum coverage and noise-free communications, place your hub: – at a convenient, high, and central location with no obstructions between the devices and hub in an indoor environment. – away from electronic appliances such as TVs, radios, personal computers, wireless devices, or other phones. – facing away from radio frequency transmitters, such as external antennas of mobile phone cell stations. (Avoid putting the hub on a bay window or near a window.) R Coverage and voice quality depends on the local environmental conditions. R If the reception for a hub location is not satisfactory, move the hub to another location for better reception. Environment R Keep the product away from electrical noise generating devices, such as fluorescent lamps and motors. R The product should be kept free from excessive smoke, dust, high temperature, and vibration. R The product should not be exposed to direct sunlight. R Do not place heavy objects on top of the product. R When you leave the product unused for a long period of time, unplug the product from the power outlet. R The product should be kept away from heat sources such as heaters, kitchen stoves, etc. It should not be placed in rooms where the temperature is less than 0 °C (32 °F) or greater than 40 °C (104 °F). Damp basements should also be avoided. R The maximum communication range may be shortened when the product is used in the following places: Near obstacles such as hills, tunnels, underground, near metal objects such as wire fences, etc. R Operating the product near electrical appliances may cause interference. Move away from the electrical appliances. Other information Routine care R Wipe the outer surface of the product with a soft moist cloth. 8 For assistance, please visit http://shop.panasonic.com/support Important Information HNB600_(en_en)_0124_ver.201.pdf 8 2017/01/25 10:22:35

abrasive powder. Protecting your recordings R Do not remove the microSD card or disconnect the hub’s AC adaptor while reading or writing data to the microSD card. Data on the card could become corrupted. R If a microSD card malfunctions or is exposed to electromagnetic waves or static electricity, data on the card could become corrupted or erased. Therefore we recommend backing up important data to a computer or other device. Notice for product disposal, transfer, or return R This product can store your private/ confidential information. To protect your privacy/confidentiality, we recommend that you erase information such as phonebook or caller list entries from the memory before you dispose of, transfer, or return the product. Notice For assistance, please visit http://shop.panasonic.com/support 9 Important Information HNB600_(en_en)_0124_ver.201.pdf 9 2017/01/25 10:22:35

C B A D E G H I F Speaker LED indicator DC jack LINE jack MWi-Fi SETUPN Used when performing initial setup. microSD card slot Used when inserting a microSD card. Remove the label when inserting. M HANDSET/LOCATORN Used when registering a handset. You can also press this button to locate a misplaced handset. M CAMERAN Used when registering a camera. M OTHER DEVICEN Used when registering other devices, such as sensors and smart plugs. LED indicator You can use the LED indicator to confirm the hub’s status. Indicator Status Off No power, or LED indicator is turned off*1 Green, lit Normal operation, connected to wireless router*1 Green, blinking slowly Registration mode Green, blinking quickly Hub is searching for wireless router Alternating: Green, blinking slowly Yellow, blinking slowly Hub is starting up (cannot be used yet)*2 Red, lit Alarm system is armed*1 Red, blinking quickly Alarm system was triggered Yellow, lit Initial setup required Yellow, blinking slowly Initial setup in progress, mobile device connected Yellow, blinking Initial setup is starting *1 You can configure the hub so that its LED indicator does not light during normal operation. For more information, refer to the User’s Guide (page 17). *2 It may take some time for the hub to finish starting up. 10 For assistance, please visit http://shop.panasonic.com/support Setup HNB600_(en_en)_0124_ver.201.pdf 10 2017/01/25 10:22:35

DC jack. Secure the AC adaptor cord by wrapping it around the hook. Connect the AC adaptor to the power outlet. Insert the telephone line cord into the LINE jack and a single-line telephone jack (RJ11C) until you hear a click.*1 DSL/ADSL service users only: Connect your DSL/ADSL filter (not supplied).*1 Outdoor Camera (KX-HNC600) or Indoor Camera (KX-HNC210) users only: Remove the label covering the card slot and then insert the microSD card (not supplied) into the slot with the notched corner (1) facing upwards (2) until it clicks into place. *1 This step is only necessary if you want to use the landline phone features. For details about the landline phone features, refer to the User’s Guide (page 17). Note: R Use only the supplied Panasonic AC adaptor PNLV236. R A microSD card (not supplied) is required to record images from cameras. Refer to the information about the available microSD card (page 3). R To remove the microSD card, push in the microSD card and then remove it. 4 5 4 3 2 1 6 1 2 Note about power connections AC adaptor connection R The AC adaptor must remain connected at all times. (It is normal for the adaptor to feel warm during use.) R The AC adaptor should be connected to a vertically oriented or floor-mounted AC outlet. Do not connect the AC adaptor to a ceiling-mounted AC outlet, as the weight of the adaptor may cause it to become disconnected. For assistance, please visit http://shop.panasonic.com/support 11 Setup HNB600_(en_en)_0124_ver.201.pdf 11 2017/01/25 10:22:35

R The hub’s telephone features will not work during a power failure. We recommend connecting a corded-type telephone that does not use an AC adaptor to your telephone line. Wi-Fi® settings After you have connected your hub, here is what you will need to do in order to access the system from your mobile device. Each procedure is explained in this chapter. 1 Download Download the [Home Network] app to your mobile device. 2 Initial setup Use the [Home Network] app to configure the hub to connect to your wireless router, and then register your mobile device to the hub. Downloading the [Home Network] app Download information is available at the web page listed below. www.panasonic.net/pcc/support/tel/ homenetwork/ Compatible mobile devices iPhone® 4 or later, iPad®, or iPad mini™ (iOS 6.0 or later) or an Android™ device (Android 4.0 or later) Note: R The [Home Network] app may not function properly depending on the system environment, such as the model of your mobile device, peripherals connected to your mobile device, and the apps installed on your mobile device. R The following Android devices are not compatible with the [Home Network] app. – Android devices that are not supported by Google Play – Android devices with limited hardware features (Bluetooth, Wi-Fi, and microphone support are required.) Initial setup Confirm the following before you begin. – Make sure you have installed the [Home Network] app on your mobile device – Make sure the hub and your wireless router are turned on and the hub’s LED indicator is lit in yellow – Make sure the hub is located within range of your wireless router – Make sure your mobile device is connected to your wireless router – Make sure your mobile device can connect to the Internet – Make sure you know the network name (SSID) and password assigned to your wireless router Initial setup for iPhone, iPad 1 Start the [Home Network] app. R If prompted, follow the on-screen instructions and select the appropriate region/country. R If prompted to select the device to be set up, tap [Hub]. 2 When prompted, tap [Set up the Hub]. 3 When prompted, press MWi-Fi SETUPN on the hub. R The LED indicator blinks in yellow. 12 For assistance, please visit http://shop.panasonic.com/support Setup HNB600_(en_en)_0124_ver.201.pdf 12 2017/01/25 10:22:35

setting temporarily so that it connects to the hub directly. R Open your mobile device’s [Settings] app, tap [Wi-Fi], select “KX-HNB600_Panasonic”, enter “00000000” as the password, and then tap [Join]. R If more than 1 item named “KX-HNB600_Panasonic” is displayed, wait approx. 10 minutes and perform this procedure from the beginning. 5 Start the [Home Network] app again. 6 If necessary, enter the password required to connect to your wireless router and then tap [Next]. R The hub and your mobile device connect to your wireless router. R If prompted, follow the on-screen instructions and connect your mobile device to your wireless router, start the app again, and then tap [Add This Mobile Device]. R If you enter the wrong Wi-Fi password, [Setup failed.] is displayed and the hub’s LED indicator lights. Proceed as follows according to the color of the hub’s LED indicator. – If the LED indicator is lit in yellow, repeat the initial setup procedure from the beginning. – If the LED indicator is blinking quickly in green, you must reset the hub’s Wi-Fi settings. See “If the hub's LED indicator blinks in green”, page 13. 7 When prompted, press MWi-Fi SETUPN on the hub. R Your mobile device will be registered to the hub. 8 When prompted, follow the on-screen instructions and set the password used to log in to the hub while away from home and then tap [OK]. 9 When prompted, enter a name for the hub and your mobile device and then tap [OK]. R The hub name setting is used by your mobile device to identify the hub. This is useful when you have multiple hubs. R The mobile device name setting is used by the hub and other system users to identify your mobile device. This is useful when performing certain operations, such as deregistering or making intercom calls using a cordless handset. 10 When prompted, select whether you want to customize device profiles, i.e., the device name, location, and other settings for your devices. R If you choose not to customize the device profiles now, you can change them later if desired. For details about customizing device profiles, refer to the User’s Guide (page 17). R If you choose to customize the device profiles now, change each setting as desired. When finished, tap repeatedly until the “completed” message is displayed. R The app’s home screen is displayed when initial setup is complete. If the hub's LED indicator blinks in green If you enter the wrong Wi-Fi password during the initial setup procedure for iPhone or iPad, [Setup failed.] is displayed and the hub’s LED indicator blinks quickly in green. In this case, perform the following. 1. Press and hold the 3 registration buttons on the side of the hub and MWi-Fi SETUPN on the back of the hub at the same time (4 buttons total) until the hub’s LED indicator blinks slowly in green and yellow. 2. Wait for the hub’s LED indicator to light in yellow. 3. Repeat the initial setup procedure (“Initial setup for iPhone, iPad”, page 12). For assistance, please visit http://shop.panasonic.com/support 13 Setup HNB600_(en_en)_0124_ver.201.pdf 13 2017/01/25 10:22:35

1 Start the [Home Network] app. R If prompted, follow the on-screen instructions and select the appropriate region/country. R If prompted to select the device to be set up, tap [Hub]. 2 When prompted, tap [Set up the Hub]. 3 When prompted, press MWi-Fi SETUPN on the hub. R The LED indicator blinks in yellow. R The app temporarily changes your mobile device’s Wi-Fi setting so that it connects to the hub directly. 4 If necessary, enter the password required to connect to your wireless router and then tap [Next]. R The hub and your mobile device connect to your wireless router. 5 When prompted, press MWi-Fi SETUPN on the hub. R Your mobile device will be registered to the hub. 6 When prompted, follow the on-screen instructions and set the password used to log in to the hub while away from home and then tap [OK]. 7 When prompted, enter a name for the hub and your mobile device and then tap [OK]. R The hub name setting is used by your mobile device to identify the hub. This is useful when you have multiple hubs. R The mobile device name setting is used by the hub and other system users to identify your mobile device. This is useful when performing certain operations, such as deregistering or making intercom calls using a cordless handset. 8 When prompted, select whether you want to customize device profiles, i.e., the device name, location, and other settings for your devices. R If you choose not to customize the device profiles now, you can change them later if desired. For details about customizing device profiles, refer to the User’s Guide (page 17). R If you choose to customize the device profiles now, change each setting as desired. When finished, press your device’s “back” button repeatedly until the “completed” message is displayed. R The app’s home screen is displayed when initial setup is complete. Information about Wi-Fi communication The hub uses Wi-Fi to communicate with your wireless router. Refer to the following information when planning where to place the hub. Do not use the hub in the following areas or locations. Malfunction or interference to radio communication may result. R Indoor areas that have certain types of radio or mobile communications equipment R Locations near microwave ovens or Bluetooth devices R Indoor areas where antitheft devices or 2.4 GHz frequency devices such as POS systems are used Do not place the hub in areas where the following materials or objects are located between the hub and the wireless router. These materials and objects may interfere with wireless communication or cause wireless transmission speed to become slower. R Metallic doors or shutters R Walls containing aluminum-sheet insulation R Walls made of concrete, stone, brick, or tin R Multiple walls R Steel shelving R Fireproof glass 14 For assistance, please visit http://shop.panasonic.com/support Setup HNB600_(en_en)_0124_ver.201.pdf 14 2017/01/25 10:22:35

device In order to access the system from a mobile device, you must first register the mobile device to the hub. You can register up to 8 mobile devices to a hub. Confirm the following before you begin. – Make sure you have completed the initial setup procedure – Make sure your mobile device can connect to the Internet – Make sure your wireless router and the hub are turned on – Make sure your mobile device and the hub are connected to the same wireless router 1 Using the mobile device that you want to register, download the [Home Network] app and then start the app. R If prompted, follow the on-screen instructions and select the appropriate region/country. R If prompted to select the device to be set up, tap [Hub]. 2 When prompted, tap [Add This Mobile Device]. 3 When prompted, press MWi-Fi SETUPN on the hub. R Your mobile device will be registered to the hub. 4 When prompted, follow the on-screen instructions and enter the password used to log in to the hub while away from home. 5 When prompted, enter a name for your mobile device and then tap [OK]. R This setting allows you to change the name assigned to your device. It can help you identify your mobile device when performing certain operations, such as deregistering or making intercom calls using a cordless handset. R The app’s home screen is displayed when initial setup is complete. Registering other devices to the hub This procedure is not required for devices that were included as part of a bundle. Before you can use devices such as cameras, sensors, and smart plugs, they must be registered to the hub. If you purchased devices separately (i.e., not as part of a bundle), you must register each device to the hub. You can register each device by using the registration buttons or the [Home Network] app. Using registration buttons 1 Hub: Press and hold the registration button until the LED indicator blinks slowly in green. R Press and hold the appropriate registration button (page 10) according to the device you want to register. M HANDSET/LOCATORN: For handsets M CAMERAN: For cameras M OTHER DEVICEN: For other devices 2 Handset: Place the handset on the charger. Devices other than handset: Press and hold the device’s registration button until the device’s LED indicator blinks slowly in green. R When registration is complete, the hub sounds one long beep. Note: R If registration fails, the hub sounds several short beeps. R To register a mobile device, use the procedure described on page 15. Using the app 1 Start the [Home Network] app. For assistance, please visit http://shop.panasonic.com/support 15 Setup HNB600_(en_en)_0124_ver.201.pdf 15 2017/01/25 10:22:35

screen, tap [Settings]. 3 Tap [Device Registration]. 4 Tap [Registration]. 5 Select the type of device that you want to register. 6 Handset: Place the handset on the charger. Devices other than handset: Press and hold the registration button on the device you want to register until the device’s LED indicator blinks slowly in green. R When registration is complete, the hub sounds one long beep. Note: R If registration fails, the hub sounds several short beeps. 16 For assistance, please visit http://shop.panasonic.com/support Setup HNB600_(en_en)_0124_ver.201.pdf 16 2017/01/25 10:22:35

device in the system from the hub is approximately 50 m (160 feet) indoors and approximately 300 m (1,000 feet) outdoors. Wireless communication may be unreliable when the following obstacles are located between the hub and other system devices. R Metal doors or screens R Walls containing aluminum-sheet insulation R Walls made of concrete or corrugated iron R Double-pane glass windows R Multiple walls R When using each device on separate floors or in different buildings Accessing the User’s Guide The User’s Guide is a collection of online documentation that helps you get the most out of the [Home Network] app. 1 iPhone/iPad Tap in the app’s home screen. Android devices Tap or press your mobile device’s menu button in the app’s home screen. 2 Tap [User’s Guide]. Note: R Microsoft® Windows® Internet Explorer® 8 and earlier versions are not supported. R Android 4.1 or later versions are recommended. R You can also access the User’s Guide at the web page listed below. www.panasonic.net/pcc/support/tel/ homenetwork/manual/ For assistance, please visit http://shop.panasonic.com/support 17 Appendix HNB600_(en_en)_0124_ver.201.pdf 17 2017/01/25 10:22:35

adaptor to wall mount the hub if desired. Note: R Make sure that the wall and the fixing method are strong enough to support the weight of the unit. 1 Connect the AC adaptor and the telephone line cord to the hub. R Secure the AC adaptor cord by wrapping it around the hook. 2 Slide the wall mounting adaptor up until it clicks into place. R Make sure the “UP” mark on the wall mounting adaptor faces upwards. R Align and insert the tabs (1) of the wall mounting adaptor to the grooves (2) of the hub. UP 1 2 UP UP 18 For assistance, please visit http://shop.panasonic.com/support Appendix HNB600_(en_en)_0124_ver.201.pdf 18 2017/01/25 10:22:35

to secure in place. R Pass the AC adaptor cord and the telephone line cord through the groove (1) in the wall mounting adaptor. Wrap up the telephone line cord as shown to prevent the cord from being pinched. R This product is compliant with the following wall phone plate sizes (2 types). 2 83 mm (3 1/4 inches) 3 102 mm (4 inches) R Fit the slots of the hub onto the corresponding wall phone plate tabs for (4) and (5) respectively. 5 2 3 4 5 4 1 Removing the wall mounting adaptor While pushing the release levers (A) away from the center of the wall mounting adaptor, slide the adaptor down (B). A A B For assistance, please visit http://shop.panasonic.com/support 19 Appendix HNB600_(en_en)_0124_ver.201.pdf 19 2017/01/25 10:22:35

Telecommunications) Wi-Fi: IEEE 802.11b/g/n R Frequency range DECT: 1.92 GHz – 1.93 GHz Wi-Fi: 2.412 GHz – 2.462 GHz (channels 1 – 11) R RF transmission power DECT: 115 mW (max.) Wi-Fi: 100 mW (peak transmission power) R Encryption WPA2™-PSK (TKIP/AES), WPA™-PSK (TKIP/AES), WEP (128/64 bit) R Simplified configuration WPS (PBC) R Power source 120 V AC, 60 Hz R Power consumption Standby: Approx. 3.5 W Maximum: Approx. 4.0 W R Operating conditions 0 °C – 40 °C (32 °F – 104 °F) 20 % – 80 % relative air humidity (dry) R Alert tone volume High alert level: approx. 90 dB Low alert level: approx. 73 dB (measured approx. 10 cm (3 15/16 inches) in front of the center of the unit) R Dimensions (height × width × depth) Approx. 42 mm ´ 130 mm ´ 130 mm (1 21/32 inches ´ 5 1/8 inches ´ 5 1/8 inches) R Mass (weight) Approx. 220 g (0.49 lb) Open source software notice R Parts of this product use open source software supplied based on the relevant conditions of the Free Software Foundation’s GPL and/or LGPL and other conditions. Please read all licence information and copyright notices related to the open source software used by this product. This information is available at the following web page: www.panasonic.net/pcc/support/tel/ homenetwork/ At least three (3) years from delivery of this product, Panasonic Corporation will give to any third party who contacts us at the contact information provided below, for a charge of no more than the cost of physically distributing source code, a complete machine-readable copy of the corresponding source code and the copyright notices covered under the GPL and the LGPL. Please note that software licensed under the GPL and the LGPL is not under warranty. www.panasonic.net/pcc/support/tel/ homenetwork/ Software information R The End User License Agreement (EULA) for the Home Network app is available at the following web page: www.panasonic.net/pcc/support/tel/ homenetwork/ 20 For assistance, please visit http://shop.panasonic.com/support Appendix HNB600_(en_en)_0124_ver.201.pdf 20 2017/01/25 10:22:35

This equipment complies with Part 68 of the FCC rules and the requirements adopted by the ACTA. On the bottom of this equipment is a label that contains, among other information, a product identifier in the format US:ACJ----------. If requested, this number must be provided to the telephone company. R Registration No.............(found on the bottom of the unit) R Ringer Equivalence No. (REN).......0.1B A plug and jack used to connect this equipment to the premises wiring and telephone network must comply with the applicable FCC Part 68 rules and requirements adopted by the ACTA. A compliant telephone cord and modular plug is provided with the product. It is designed to be connected to a compatible modular jack that is also compliant. The REN is used to determine the number of devices that may be connected to a telephone line. Excessive RENs on a telephone line may result in the devices not ringing in response to an incoming call. In most but not all areas, the sum of RENs should not exceed five (5.0). To be certain of the number of devices that may be connected to a line, as determined by the total RENs, contact the local telephone company. For products approved after July 23, 2001, the REN for the product is part of the product identifier that has the format US:AAAEQ##TXXXX. The digits represented by ## are the REN without a decimal point (e.g., 03 is a REN of 0.3). If this equipment causes harm to the telephone network, the telephone company will notify you in advance that temporary discontinuance of service may be required. But if advance notice isn’t practical, the telephone company will notify the customer as soon as possible. Also, you will be advised of your right to file a complaint with the FCC if you believe it is necessary. The telephone company may make changes in its facilities, equipment, operations or procedures that could affect the operation of the equipment. If this happens the telephone company will provide advance notice in order for you to make necessary modifications to maintain uninterrupted service. If trouble is experienced with this equipment, for repair or warranty information, please contact a Factory Service Center or other Authorized Servicer. If the equipment is causing harm to the telephone network, the telephone company may request that you disconnect the equipment until the problem is resolved. Connection to party line service is subject to state tariffs. Contact the state public utility commission, public service commission or corporation commission for information. If your home has specially wired alarm equipment connected to the telephone line, ensure the installation of this equipment does not disable your alarm equipment. If you have questions about what will disable alarm equipment, consult your telephone company or a qualified installer. This equipment is hearing aid compatible as defined by the FCC in 47 CFR Section 68.316. When you hold the phone to your ear, noise might be heard in your Hearing Aid. Some Hearing Aids are not adequately shielded from external RF (radio frequency) energy. If noise occurs, use an optional headset accessory or the speakerphone option (if applicable) when using this phone. Consult with your audiologist or Hearing Aid manufacturer about the availability of Hearing Aids which provide adequate shielding to RF energy commonly emitted by digital devices. WHEN PROGRAMMING EMERGENCY NUMBERS AND(OR) MAKING TEST CALLS TO EMERGENCY NUMBERS: 1. Remain on the line and briefly explain to the dispatcher the reason for the call. For assistance, please visit http://shop.panasonic.com/support 21 Appendix HNB600_(en_en)_0124_ver.201.pdf 21 2017/01/25 10:22:35

hours, such as early morning or late evenings. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Privacy of communications may not be ensured when using this device. CAUTION: Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this device. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: – Reorient or relocate the receiving antenna. – Increase the separation between the equipment and receiver. – Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. – Consult the dealer or an experienced radio/ TV technician for help. Some devices operate at frequencies that may cause interference to nearby TVs and VCRs. To minimize or prevent such interference, this device should not be placed near or on top of a TV or VCR. If interference is experienced, move this device further away from the TV or VCR. This will often reduce or eliminate interference. FCC RF Exposure Warning: R This product complies with FCC radiation exposure limits set forth for an uncontrolled environment. R To comply with FCC RF exposure requirements, the hub must be installed and operated 20 cm (8 inches) or more between the product and all person’s body. R This product may not be collocated or operated in conjunction with any other antenna or transmitter. R For body-worn operation, the device must be used only with a non-metallic accessory. Use of other accessories may not ensure compliance with FCC RF exposure requirements. Notice: R FCC ID can be found on the bottom of the unit. 22 For assistance, please visit http://shop.panasonic.com/support Appendix HNB600_(en_en)_0124_ver.201.pdf 22 2017/01/25 10:22:35

Monday - Friday 9 am to 9 pm; Saturday - Sunday 10 am to 7 pm, EST. Accessories! http://shop.panasonic.com/support Customer Services Directory Shop for all your Panasonic gear Go to Get everything you need to get the most out of your Panasonic products Accessories & Parts for your Camera, Phone, A/V products, TV, Computers & Networking, Personal Care, Home Appliances, Headphones, Ba�eries, Backup Chargers & more… For Product Informa�on, Opera�ng Assistance, Parts, Owner’s Manuals, Dealer and Service info go to http://shop.panasonic.com/support For the hearing or speech impaired TTY: 1- 877-833-8855 As of June 2015 For assistance, please visit http://shop.panasonic.com/support 23 Appendix HNB600_(en_en)_0124_ver.201.pdf 23 2017/01/25 10:22:35

Limited Warranty Coverage (For USA Only) Labor One (1) Year Parts One (1) Year To submit a new repair request and for quick repair status visit our Web Site at http://shop.panasonic.com/support Panasonic Products Limited Warranty Online Repair Request Mail-In Service--Online Repair Request If your product does not work properly because of a defect in materials or workmanship, Panasonic Corporation of North America (referred to as “the warrantor”) will, for the length of the period indicated on the chart below, which starts with the date of original purchase (“warranty period”), at its option either (a) repair your product with new or refurbished parts, (b) replace it with a new or a refurbished equivalent value product, or (c) refund your purchase price. The decision to repair, replace or refund will be made by the warrantor. During the “Labor” warranty period there will be no charge for labor. During the “Parts” warranty period, there will be no charge for parts. This Limited Warranty excludes both parts and labor for non-rechargeable batteries, antennas, and cosmetic parts (cabinet). This warranty only applies to products purchased and serviced in the United States. This warranty is extended only to the original purchaser of a new product which was not sold “as is”. Home Network System Products microSD card (Included model only) 90 days N/A When shipping the unit, carefully pack, include all supplied accessories listed in the Owner’s Manual, and send it prepaid, adequately insured and packed well in a carton box. When shipping Lithium Ion batteries please visit our Web Site at http://shop.panasonic.com/support as Panasonic is committed to providing the most up to date information. Include a letter detailing the complaint, a return address and provide a daytime phone number where you can be reached. A valid registered receipt is required under the Limited Warranty. IF REPAIR IS NEEDED DURING THE WARRANTY PERIOD, THE PURCHASER WILL BE REQUIRED TO FURNISH A SALES RECEIPT/PROOF OF PURCHASE INDICATING DATE OF PURCHASE, AMOUNT PAID AND PLACE OF PURCHASE. CUSTOMER WILL BE CHARGED FOR THE REPAIR OF ANY UNIT RECEIVED WITHOUT SUCH PROOF OF PURCHASE. Product or Part Name 24 For assistance, please visit http://shop.panasonic.com/support Appendix HNB600_(en_en)_0124_ver.201.pdf 24 2017/01/25 10:22:35

(As examples, this excludes damages for lost time, travel to and from the servicer, loss of or damage to media or images, data or other memory or recorded content. The items listed are not exclusive, but for illustration only.) This warranty ONLY COVERS failures due to defects in materials or workmanship, and DOES NOT COVER normal wear and tear or cosmetic damage. The warranty ALSO DOES NOT COVER damages which occurred in shipment, or failures which are caused by products not supplied by the warrantor, or failures which result from accidents, misuse, abuse, neglect, mishandling, misapplication, alteration, faulty installation, set-up adjustments, misadjustment of consumer controls, improper maintenance, power line surge, lightning damage, modification, introduction of sand, humidity or liquids, commercial use such as hotel, office, restaurant, or other business or rental use of the product, or service by anyone other than a Factory Service Center or other Authorized Servicer, or damage that is attributable to acts of God. THERE ARE NO EXPRESS WARRANTIES EXCEPT AS LISTED UNDER “LIMITED WARRANTY COVERAGE”. THE WARRANTOR IS NOT LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES RESULTING FROM THE USE OF THIS PRODUCT, OR ARISING OUT OF ANY BREACH OF THIS WARRANTY. ALL EXPRESS AND IMPLIED WARRANTIES, INCLUDING THE WARRANTY OF MERCHANTABILITY, ARE LIMITED TO THE PERIOD OF THE LIMITED WARRANTY. PARTS AND SERVICE, WHICH ARE NOT COVERED BY THIS LIMITED WARRANTY, ARE YOUR RESPONSIBILITY. Some states do not allow the exclusion or limitation of incidental or consequential damages, or limitations on how long an implied warranty lasts, so the exclusions may not apply to you. This warranty gives you specific legal rights and you may also have other rights which vary from state to state. If a problem with this product develops during or after the warranty period, you may contact your dealer or Service Center. If the problem is not handled to your satisfaction, then write to: Consumer Affairs Department Panasonic Corporation of North America 661 Independence Pkwy Chesapeake, VA 23320 As of June 2015 For assistance, please visit http://shop.panasonic.com/support 25 Appendix HNB600_(en_en)_0124_ver.201.pdf 25 2017/01/25 10:22:35

If your product is not working properly. . . IMPORTANT! Visit our Web site: http://shop.panasonic.com/support • FAQ and troubleshooting hints are available. Use the Home Network app to access the User’s Guide and refer to the Troubleshooting section. For your future reference We recommend keeping a record of the following information to assist with any repair under warranty. Serial No. Date of purchase (found on the bottom of the unit) Name and address of dealer Attach your purchase receipt here. Two Riverfront Plaza, Newark, NJ 07102-5490 © Panasonic Corporation 2014 HNB600_(en_en)_0124_ver.201.pdf 28 2017/01/25 10:22:36

Sistema de red doméstico HUB Modelo n° KX-HNB600 Gracias por adquirir un producto Panasonic. Este documento explica cómo configurar el hub y cómo acceder a él desde un dispositivo móvil. Se deben seguir estos pasos para poder usar el sistema. Para obtener detalles sobre cómo usar el sistema, consulte la Guía del usuario (pági- na 10). Lea este documento antes de usar la unidad, y guárdelo para consultarlo en el futuro. Para obtener ayuda, comuníquese con nosotros llamando al 1-800-272-7033 o visite nuestro sitio web: http://shop.panasonic.com/support para clientes en los EE. UU. (solo en inglés) Por favor, registre su producto: http://shop.panasonic.com/support PNQX6695XA CC0814WK2126 (E) HNB600_(es_es)_0125_ver201.pdf 1 2017/01/25 17:33:55

Led indicador ........................................................3 Conexiones ..........................................................4 Configuraciones de Wi-Fi® ...................................5 Registro de otro dispositivo móvil ........................8 Registro de otros dispositivos al hub ...................8 Apéndice Alcance de la comunicación inalámbrica (DECT) ...............................................................10 Acceso a la Guía del usuario .............................10 Montaje en la pared ...........................................11 2 Tabla de Contenido HNB600_(es_es)_0125_ver201.pdf 2 2017/01/25 17:33:55

y funciones C B A D E G H I F Altavoz Led indicador Clavija de corriente continua Clavija LINE MWi-Fi SETUPN Se usa durante la configuración inicial. Ranura para tarjeta microSD Se usa mientras inserta una tarjeta microSD. Retire la etiqueta cuando la inserte. M HANDSET/LOCATORN Se usa al registrar un auricular. También puede presionar este botón para ubicar un auricular perdido. M CAMERAN Se usar al registrar una cámara. M OTHER DEVICEN Se usa al registrar otros dispositivos, como sensores y conectores inteligentes. Led indicador Puede usar el Led indicador para confirmar el estado del hub. Indicador Estado Apagado Sin energía, o el Led indicador está apaga- do*1 Verde, encendido Funcionamiento nor- mal, conectado al enru- tador inalámbrico*1 Verde, parpadeando lentamente Modo de registro Verde, parpadeo rápi- do El hub está buscando el enrutador inalámbri- co Alterna entre: Verde, parpadeando lentamente Amarillo, parpadeo len- to El hub se está inician- do (no se puede usar aún)*2 Rojo, encendido El sistema de alarma está armado*1 Rojo, parpadeo rápido Se disparó el sistema de alarma Amarillo, encendido Se debe realizar la con- figuración inicial Amarillo, parpadeo len- to Configuración inicial en progreso, dispositi- vo móvil conectado Amarillo, parpadeante La configuración inicial está arrancando *1 Puede configurar el hub de forma tal que el Led indicador no se encienda durante el funcionamiento normal. Para obtener más información, consulte la Guía del usuario (página 10). *2 Es posible que el hub tarde un tiempo en terminar de iniciar. Para obtener ayuda, visite http://shop.panasonic.com/support 3 Configuración HNB600_(es_es)_0125_ver201.pdf 3 2017/01/25 17:33:55

firmemente en la clavija de corriente continua. Asegure el cable del adaptador de corriente alterna enrollándolo en el gancho. Conecte el adaptador de corriente a la toma de corriente. Inserte el cable de línea telefónica en la clavija de LINE y la toma telefónica de una sola línea (RJ11C) hasta que escuche un clic.*1 Solo para los usuarios de servicio DSL/ ADSL: conecte su filtro DSL/ADSL (no incluido).*1 Solo usuarios de Cámara exterior (KX-HNC600) o Cámara interior (KX-HNC210): retire la etiqueta que cubre la ranura de la tarjeta y luego inserte la tarjeta microSD (no se incluye) con la esquina dentada (1) hacia arriba en la ranura (2) hasta que escuche un clic. *1 Este paso solo es necesario si desea usar funciones de telefonía fija. Para obtener detalles sobre las funciones de telefonía fija, consulte la Guía del usuario (página 10). Nota: R Use solo el adaptador de corriente alterna Panasonic PNLV236 que se suministra. R Se necesita una tarjeta microSD (no incluida) para grabar imágenes de cámaras. R Para extraer la tarjeta microSD, presiónela hacia dentro primero y luego extráigala. 4 5 4 3 2 1 6 1 2 Nota acerca de las conexiones de alimentación Adaptador de corriente alterna R El adaptador de corriente debe permanecer conectado en todo momento (es normal que el adaptador se caliente durante su uso). R El adaptador de corriente debe estar conectado a un enchufe de corriente orientado verticalmente o en una toma de corriente alterna colocada en el piso. No conecte el adaptador de corriente alterna a una toma de corriente montada en el techo, ya que el peso del adaptador puede hacer que se desconecte. 4 Para obtener ayuda, visite http://shop.panasonic.com/support Configuración HNB600_(es_es)_0125_ver201.pdf 4 2017/01/25 17:33:55

R El hub no funciona durante las fallas del suministro eléctrico. R Las funciones telefónicas del hub no trabajarán durante un corte de energía. Recomendamos que conecte un teléfono con cable que no utilice un adaptador de CA a su línea telefónica. Configuraciones de Wi-Fi® Después de conectar el hub, necesitará lo siguiente para acceder al sistema desde su dispositivo móvil. En este capítulo se explica cada procedimiento. 1 Descarga Descargue la aplicación [Home Network] a su dispositivo móvil. 2 Configuración inicial Use la aplicación [Home Network] para configurar el hub y que se conecte al enrutador inalámbrico; a continuación, registre el dispositivo móvil en el hub. Cómo descargar la aplicación [Home Network] La información de descarga está disponible en la siguiente página web. www.panasonic.net/pcc/support/tel/ homenetwork/ Dispositivos móviles compatibles iPhone® 4 o posterior, iPad®, o iPad mini™ (iOS 6.0 o posterior) o un dispositivo Android™ (Android 4.0 o posterior) Nota: R Es posible que la aplicación [Home Network] no funcione correctamente dependiendo del entorno del sistema, como el modelo de su dispositivo móvil, los periféricos conectados al mismo y las aplicaciones instaladas en él. R Los siguientes dispositivos Android no son compatibles con la aplicación [Home Network]. – Dispositivos Android que no son compatibles con Google Play – Dispositivos con Android, con características de hardware limitadas (se requiere compatibilidad con Bluetooth, Wi-Fi y micrófono). Configuración inicial Confirme lo siguiente antes de comenzar. – Asegúrese de haber instalado la aplicación [Home Network] en su dispositivo móvil – Asegúrese de que el hub y su enrutador inalámbrico estén encendidos y que el Led indicador del hub esté encendido en amarillo – Asegúrese de que el hub esté ubicado dentro del alcance del enrutador inalámbrico – Asegúrese de que el dispositivo móvil esté conectado al enrutador inalámbrico – Asegúrese de que su dispositivo móvil pueda conectarse a Internet – Asegúrese de conocer el nombre de la red (SSID) y la clave que se asignó al enrutador inalámbrico Configuración inicial para iPhone, iPad 1 Inicie la aplicación [Home Network]. R Si se le solicita, siga las instrucciones en pantalla y seleccione la región y el país apropiados. R Si se le solicita que seleccione el dispositivo que desea configurar, toque [Hub]. 2 Cuando se le solicite, toque [Configurar el Hub]. Para obtener ayuda, visite http://shop.panasonic.com/support 5 Configuración HNB600_(es_es)_0125_ver201.pdf 5 2017/01/25 17:33:55

en el hub. R El Led indicador parpadea en amarillo. 4 Cambie la configuración de Wi-Fi de su dispositivo móvil temporalmente para que se conecte directamente al hub. R Abra la aplicación [Configuración] en su dispositivo móvil, toque [Wi-Fi], seleccione “KX-HNB600_Panasonic”, introduzca “00000000” como clave y luego toque [Conectar]. R Si aparece más de 1 elemento llamado “KX-HNB600_Panasonic”, espere aprox. 10 minutos y realice este procedimiento desde el inicio. 5 Inicie de nuevo la aplicación [Home Network]. 6 Si es necesario, introduzca la clave requerida para conectarse al enrutador inalámbrico y, a continuación, presione [Sig.]. R El hub y su dispositivo móvil se conectan a su enrutador inalámbrico. R Si se le solicita, siga las instrucciones en la pantalla y conecte su dispositivo móvil a su enrutador inalámbrico, reinicie la aplicación y luego toque [Añadir este dispositivo móvil]. R Si introduce una clave de Wi-Fi incorrecta, aparece [La instalación ha fallado.] y el LED indicador del hub se encenderá. Proceda de la siguiente manera según el color del LED indicador del hub. – Si la luz del LED indicador es amarilla, repita el procedimiento de instalación desde el comienzo. – Si la luz del LED indicador parpadea en verde rápidamente, debe reiniciar la configuración Wi-Fi del hub. Consulte “Si el LED indicador del hub parpadea en verde”, página 6. 7 Cuando se le solicite, oprima MWi-Fi SETUPN en el hub. R Se registrará el dispositivo móvil en el hub. 8 Cuando se le solicite, siga las instrucciones en la pantalla y establezca la clave usada para acceder al hub mientras está fuera de su casa. A continuación, toque [Aceptar]. 9 Cuando se le solicite, introduzca un nombre para el hub y para el dispositivo móvil y toque [Aceptar]. R Su dispositivo móvil utiliza la configuración del nombre del hub para identificar el hub. Esto resulta útil cuando tiene varios hubs. R Los usuarios del hub y otros sistemas utilizan la configuración del nombre del dispositivo móvil para identificar su dispositivo móvil. Esto puede ser útil al realizar ciertas operaciones, como anular el registro o realizar llamadas de intercomunicador con un auricular inalámbrico. 10 Cuando se le solicite, seleccione si desea personalizar perfiles de dispositivos, como el nombre del dispositivo, ubicación y otros ajustes de configuración para sus dispositivos. R Si opta por no personalizar los perfiles del dispositivo en este momento, puede cambiarlos más tarde si lo desea. Para obtener detalles sobre personalización de perfiles de dispositivos, consulte la Guía del usuario (página 10). R Si opta por personalizar los perfiles de los dispositivos en este momento, cambie cada uno de los ajustes de configuración según lo desee. Al finalizar, toque reiteradamente hasta que aparezca el mensaje “completado”. R Aparecerá la pantalla de inicio de la aplicación una vez completada la configuración inicial. Si el LED indicador del hub parpadea en verde Si introduce una clave de Wi-Fi incorrecta durante el procedimiento de configuración inicial para iPhone o iPad, aparece [La instalación ha fallado.] y el LED indicador del hub parpadea rápidamente en verde. En este caso, realice lo siguiente. 1. Mantenga oprimidos al mismo tiempo los 3 botones de registro en el lateral del hub y MWi-Fi SETUPN en la parte trasera del hub (4 botones en total) hasta que el Led indicador del hub parpadee lentamente en verde y amarillo. 2. Espere hasta que el Led indicador del hub se mantenga en amarillo. 3. Repita el procedimiento de configuración inicial (“Configuración inicial para iPhone, iPad”, página 5). 6 Para obtener ayuda, visite http://shop.panasonic.com/support Configuración HNB600_(es_es)_0125_ver201.pdf 6 2017/01/25 17:33:56

Android 1 Inicie la aplicación [Home Network]. R Si se le solicita, siga las instrucciones en pantalla y seleccione la región y el país apropiados. R Si se le solicita que seleccione el dispositivo que desea configurar, toque [Hub]. 2 Cuando se le solicite, toque [Configurar el Hub]. 3 Cuando se le solicite, oprima MWi-Fi SETUPN en el hub. R El Led indicador parpadea en amarillo. R La aplicación cambia temporalmente la configuración Wi-Fi de su dispositivo móvil para que se conecte de forma directa al hub. 4 Si es necesario, introduzca la clave requerida para conectarse al enrutador inalámbrico y, a continuación, presione [Sig.]. R El hub y su dispositivo móvil se conectan a su enrutador inalámbrico. 5 Cuando se le solicite, oprima MWi-Fi SETUPN en el hub. R Se registrará el dispositivo móvil en el hub. 6 Cuando se le solicite, siga las instrucciones en la pantalla y establezca la clave usada para acceder al hub mientras está fuera de su casa. A continuación, toque [Aceptar]. 7 Cuando se le solicite, introduzca un nombre para el hub y para el dispositivo móvil y toque [Aceptar]. R Su dispositivo móvil utiliza la configuración del nombre del hub para identificar el hub. Esto resulta útil cuando tiene varios hubs. R Los usuarios del hub y otros sistemas utilizan la configuración del nombre del dispositivo móvil para identificar su dispositivo móvil. Esto puede ser útil al realizar ciertas operaciones, como anular el registro o realizar llamadas de intercomunicador con un auricular inalámbrico. 8 Cuando se le solicite, seleccione si desea personalizar perfiles de dispositivos, como el nombre del dispositivo, ubicación y otros ajustes de configuración para sus dispositivos. R Si opta por no personalizar los perfiles del dispositivo en este momento, puede cambiarlos más tarde si lo desea. Para obtener detalles sobre personalización de perfiles de dispositivos, consulte la Guía del usuario (página 10). R Si opta por personalizar los perfiles de los dispositivos en este momento, cambie cada uno de los ajustes de configuración según lo desee. Al finalizar, oprima el botón “volver” reiteradamente hasta que aparezca el mensaje “completado”. R Aparecerá la pantalla de inicio de la aplicación una vez completada la configuración inicial. Información acerca de la comunicación Wi-Fi El hub usa Wi-Fi para comunicarse con su enrutador inalámbrico. Consulte la siguiente información cuando piense en dónde colocar el hub. No coloque el hub en las siguientes áreas o ubicaciones. Es posible que existan fallas o interferencias en la comunicación por radio. R Interiores donde haya equipos con cierto tipo de comunicación por radio o móvil R Ubicaciones cerca de hornos microondas o dispositivos Bluetooth R Interiores donde haya dispositivos antirrobos o dispositivos en frecuencias de 2.4 GHz como los sistemas POS No coloque un hub en áreas donde se encuentren los siguientes materiales u objetos entre el hub y el enrutador inalámbrico. Dichos materiales y objetos pueden interferir con la comunicación inalámbrica o pueden provocar que la velocidad de transmisión se reduzca. R Puertas metálicas R Paredes que contengan aislamiento de aluminio R Paredes de hormigón, piedra, ladrillo o estaño R Varias paredes R Repisas de acero R Vidrio a prueba de incendios Para obtener ayuda, visite http://shop.panasonic.com/support 7 Configuración HNB600_(es_es)_0125_ver201.pdf 7 2017/01/25 17:33:56

móvil Para acceder al sistema desde un dispositivo móvil, primero debe registrarlo en el hub. Puede registrar hasta 8 dispositivos móviles en un hub. Confirme lo siguiente antes de comenzar. – Asegúrese de haber completado el procedimiento de configuración inicial – Asegúrese de que su dispositivo móvil pueda conectarse a Internet – Asegúrese de que el el enrutador inalámbrico y el hub estén encendidos – Asegúrese de que el dispositivo móvil y el hub estén conectados al mismo enrutador 1 Desde el dispositivo móvil que desea registrar, descargue la aplicación [Home Network] y luego iníciela. R Si se le solicita, siga las instrucciones en pantalla y seleccione la región y el país apropiados. R Si se le solicita que seleccione el dispositivo que desea configurar, toque [Hub]. 2 Cuando se le solicite, toque [Añadir este dispositivo móvil]. 3 Cuando se le solicite, oprima MWi-Fi SETUPN en el hub. R Se registrará el dispositivo móvil en el hub. 4 Cuando se le solicite, siga las instrucciones en la pantalla e introduzca la clave usada para acceder al hub. 5 Cuando se le solicite, introduzca un nombre para el dispositivo móvil y toque [Aceptar]. R Esta configuración le permite cambiar el nombre asignado a este dispositivo. Esto puede ser útil para identificar el dispositivo móvil cuando realice ciertas operaciones, como anular el registro o realizar llamadas de intercomunicación con un auricular inalámbrico. R Aparecerá la pantalla de inicio de la aplicación una vez completada la configuración inicial. Registro de otros dispositivos al hub Este procedimiento no es necesario para unida- des que son parte de un paquete. Antes de poder usar dispositivos como cámaras, sensores y conectores inteligentes, se deben registrar en el hub. Si compró los dispositivos por separado (es decir, no como parte de un paquete), debe registrar cada dispositivo en el hub. Puede registrar cada unidad mediante los botones de registro o la aplicación [Home Network]. Uso de los botones de registro 1 Hub: Oprima y mantenga oprimido el botón de registro hasta que el Led indicador parpadee lentamente en verde. R Oprima y mantenga oprimido el botón de registro correspondiente (página 3) en función del dispositivo que desea registrar. M HANDSET/LOCATORN: Para auriculares M CAMERAN: Para cámaras M OTHER DEVICEN: Para otros dispositivos 2 Auricular: Coloque el auricular en el cargador. Dispositivos que no sean auriculares: Mantenga presionado el botón de registro del dispositivo hasta que el Led indicador parpadee lentamente en verde. R Cuando se ha completado el registro, el hub emitirá un pitido largo. Nota: R Si el registro falla, el hub emitirá varios pitidos cortos. R Para registrar un dispositivo móvil, use el procedimiento descrito en página 8 8 Para obtener ayuda, visite http://shop.panasonic.com/support Configuración HNB600_(es_es)_0125_ver201.pdf 8 2017/01/25 17:33:56

1 Inicie la aplicación [Home Network]. 2 Desde la pantalla de inicio de la aplicación [Home Network], toque [Configuración]. 3 Toque [Registro de dispositivos]. 4 Toque [Registro]. 5 Seleccione el tipo de dispositivo que desea registrar. 6 Auricular: Coloque el auricular en el cargador. Dispositivos que no sean auriculares: Mantenga presionado el botón de registro del dispositivo que desea registrar hasta que el Led indicador parpadee lentamente en verde. R Cuando se ha completado el registro, el hub emitirá un pitido largo. Nota: R Si el registro falla, el hub emitirá varios pitidos cortos. Para obtener ayuda, visite http://shop.panasonic.com/support 9 Configuración HNB600_(es_es)_0125_ver201.pdf 9 2017/01/25 17:33:56

inalámbrica (DECT) El alcance de la comunicación inalámbrica de cada dispositivo en el sistema del hub es de aproximadamente 50 m (160 pies) en interiores y de aproximadamente 300 m (1,000 pies) en el exterior. Es posible que la comunicación inalámbrica no sea tan confiable cuando se encuentran los obstáculos siguientes entre el hub y otros dispositivos del sistema. R Puertas o pantallas metálicas R Paredes que contengan aislamiento de aluminio R Paredes de hormigón o hierro corrugado R Ventanas de vidrio doble R Varias paredes R Cuando los dispositivos están en pisos o edificios diferentes Acceso a la Guía del usuario La Guía del usuario es una colección de documentación en línea que lo ayuda a aprovechar al máximo la aplicación [Home Network]. 1 iPhone/iPad Toque en la pantalla de inicio de la aplicación. Dispositivos Android Toque u oprima el botón menú de su dispositivo en la pantalla de inicio de la aplicación. 2 Toque [Guía del Usuario]. Nota: R No se admite Microsoft® Windows® Internet Explorer® 8 y versiones anteriores. R Se recomienda Android 4.1 y versiones posteriores. R También puede acceder a la Guía del usuario mediante la página web a continuación. www.panasonic.net/pcc/support/tel/ homenetwork/manual/ 10 Para obtener ayuda, visite http://shop.panasonic.com/support Apéndice HNB600_(es_es)_0125_ver201.pdf 10 2017/01/25 17:33:56

Puede usar el adaptador de instalación en pared incluido para instalar el hub de dicha forma si lo desea. Nota: R Asegúrese de que la pared y el método de colocación sean lo suficientemente resistentes para soportar el peso de la unidad. 1 Conecte el adaptador de corriente y el cable de línea telefónica al hub. R Asegure el cable del adaptador de corriente alterna enrollándolo en el gancho. 2 Deslice el adaptador de instalación en pared hasta que encaje y haga clic. R Asegúrese de que la marca “UP” en el adaptador de instalación en pared mire hacia arriba. R Alinee e inserte las pestañas (1) del adaptador de instalación en pared en las ranuras (2) del hub. UP 1 2 UP UP Para obtener ayuda, visite http://shop.panasonic.com/support 11 Apéndice HNB600_(es_es)_0125_ver201.pdf 11 2017/01/25 17:33:56

asegurarlo en su sitio. R Pase el cable del adaptador de corriente y el de la línea telefónica por la ranura (1) en el adaptador de instalación en pared. Enrolle el cable de línea telefónica como se muestra para evitar que se quede pillado. R Este producto es compatible con los siguientes tamaños de placas de los teléfonos (tipos 2). 2 83 mm (3 1/4 pulgadas) 3 102 mm (4 pulgadas) R Ajuste las ranuras del hub en las pestañas correspondientes de la placa del teléfono (4) y (5) respectivamente. 5 2 3 4 5 4 1 Extracción del adaptador de instalación en pared Mientras aleja las palancas de desbloqueo (A) del adaptador de instalación en pared, deslice el adaptador hacia abajo (B). A A B 12 Para obtener ayuda, visite http://shop.panasonic.com/support Apéndice HNB600_(es_es)_0125_ver201.pdf 12 2017/01/25 17:33:56