Valor GV34 Operation Manual

used on Valor heaters 738, 739-72 and RF24B Push-on Connector Connect Remote Control Receiver 1. Connect the wiring harness to the receiver box, by pushing the wire connector on to the receiver circuit board. The plug will only go on one way so please ensure that the wires are pointing up and the slot in the board is in line with the tab on the wiring harness plug. 2. Connect the wires as shown. Please note that the “L” connectors are diff erent sizes; the smaller one fi ts to the lower connection and the larger one the top connection on the top left hand side of the valve. The other two wire connectors can be fi tted to either terminal located to the left of the fl ame control button. 3. Remove the remote control receiver lid. 4. Fit four AA 1.5 V alkaline batteries. Refi t the lid. 5. Place the remote control receiver on the base of the fi replace beside the valve. 6. Fit the 9 V alkaline battery to the handset transmitter. Remote control operating instructions are on following pages of this manual and are supplied with the remote control kit. GV34 Valve Receiver Push-on Connector CAUTION DO NOT USE a screwdriver or other metallic object to remove the batteries from the receiver or the handset! This could cause a short circuit to the receiver. CAUTION DO NOT PUT BATTERIES IN THE REMOTE CONTROL RECEIVER until the wires are connected to the burner control unit as short-circuit could result in the destruction of the electrical components.

Your fi replace remote control helps you get the comfort, convenience and aesthetics you want from your gas fi replace. The remote controls your fi replace in diff erent ways. IMPORTANT: BEFORE YOU BEGIN, please note that on this system, the settings of time, temperature and automatic ON/OFF can only be programmed when the function display is fl ashing. Be patient when programming as it can take a few seconds to set. Setting the time The fi rst thing to do is to set the time. 1. With your thumb, hold down both the AUTO and TIMER buttons until F fl ashes. Let go. 2. Note the digital clock on the bottom right hand corner. The ▲ button sets the hour; the ▼ button sets the minutes. Set the time. Note: You must start setting the time while the F is fl ashing. If it stops fl ashing, go back to 1. 3. The display shows °C/24-hour or °F/12-hour. To change the temperature/hour display, press on the AUTO button while the display fl ashes. 4. Let go and wait until the fl ashing stops. The remote shows the time you set. It also shows the current temperature. Setting the temperature Use this setting when you come in and want to enjoy a specifi c temperature. 1. Push the AUTO button until a number and F fl ash. Let go. 2. While it is still fl ashing, push the ▲ and ▼ buttons to the temperature you want. Let go. Your fi replace will reach that temperature and the remote will check the temperature every fi ve minutes, adjusting the amount of fuel needed to give you a steady, even heat. Setting the fl ame Use this setting when you want a particular fl ame level. For instance, you want to watch fl ames burn at their highest level and you don’t mind if the room is too hot. 1. To raise the fl ame, press and hold the ▲ button until the flame gets to the desired level. Let go. 2. To lower the fl ame, press and hold the ▼ button until the fl ame gets to the desired level. Let go. The fl ame level will remain just as you set it.

190–2255 Dollarton Highway, North Vancouver, BC, CANADA V7H 3B1 Tel. 604-984-3496 Fax 604-984-0246 www.valorfi replaces.com Because our policy is one of constant development and improvement, details may vary slightly from those given in this publication. Programming time and temperature You can set your fi replace to come on before you wake up and turn off after you leave and then, turn on again just before you come home and turn off after going to bed. You can leave it like this for the heating season. 1. Decide what temperature you want your fi replace to be at. Also, decide what time you want your fi replace to turn on and off . Finally, decide what time you want it to come back on and off in the afternoon or evening. For the fi rst few times you set the timer, it’s handy to write these times down. 2. Set the temperature (just as you did in the section Setting the temperature.) 3. Press the TIMER button and hold it until P1 ☼ appears and flashes. Let go. While fl ashing, push the buttons ▲ (hour) and ▼ (minutes) to set the time at which you want your fi replace to turn on in the morning. 4. Press the TIMER button and hold it until P1 appears and fl ashes. Let go. While fl ashing, push the buttons ▲ (hour) and ▼ (minutes) to set the time at which you want your fi replace to turn off when you leave. 5. Press the TIMER button and hold it until P2 ☼ appears and fl ashes. Let go. While fl ashing, push the buttons ▲ (hour) and ▼ (minutes) to set the time at which you want your fi replace will turn back on in the afternoon. 6. Press the TIMER button and hold it until P2 appears and fl ashes. Let go. While fl ashing, push the buttons ▲ (hour) and ▼ (minutes) to set the time at which you want your fi replace to turn off in the evening. 7. That is all you have to do. Your fi replace will give you steady, even heat at the temperatures and times you set. Note: If you want to set your fi replace for only one time on and off , set P2 ☼ and P2 for the same times as P1 . The remote will record the P1 off time for both P2 times. To temporarily override the timer setting, just press AUTO or ▲ and ▼ to go back to manual settings. Press TIMER to go back to your settings. Battery Replacement When your remote control displays BATT, you need to replace the batteries. Handset: one 9 volt alkaline battery. Receiver: four AA 1.5 volt alkaline batteries. CAUTION DO NOT USE a screwdriver or other metallic object to remove the batteries from the receiver or the handset! This could cause a short circuit to the receiver.