RocketFish EX7 Quick Setup Manual

1 charger 1 USB charging cable 1 Quick Setup Guide (what you’re looking at) 4 round earbuds 3 ftted earbuds (medium size is pre-attached) 1 ear loop 1 Lift the charging port cover, then connect the charger. When, the indicator changes from red to green, and you can disconnect the charger.(See no.11 and no. 36) Use one of the ftted earbuds for the most convenient and comfortable ft, or alternatively use a round earbud in combination with the ear loop. To use a rounded earbud: 1 Remove the ftted earbud that's already attached, then press the round earbud onto the headset. 2 Attach the ear loop for a secure ft. 3 Activate Bluetooth on your phone, then set your phone to search for nearby Bluetooth devices. For help with this step, see your cell phone’s user guide. 4 When your phone detects the RF-EX7, select it on the list, then enter “0000” (zeros) for the PIN. The headset beeps and the indicator turns green. To turn of the headset, press and hold the power button for about two seconds. 2 Press and hold the power button for 3 seconds to turn on your headset. It will automatically enter pairing mode when you turn it on for the frst time. When in pairing mode, the LED light will blink Green.(on confrmation) 1 Power & Pair 2 Get the perfect ft What’s in the box: LED light Ear bud Charging port with cover On/Of (reverse side) Volume touch pad Send/end button Bottom view To use a ftted earbud: 1 Attach the appropriate size of ftted earbud onto the headset. The medium ftted earbud is already attached. 2 Insert the headset vertically in your ear (shown in step 2) 3 Rotate the headset up towards your mouth. The fexible portion of the ear bud should ft securely towards the back of your outer ear. You may need to guide it to a comfortable position with your fnger. Ear loop Round earbuds Fitted earbuds Charger Headset LED light What is PureSpeech®? PureSpeech is a state-of-the-art noise cancelation and signal processing technology created by SRS Labs and CSR. Your EX7 headset incorporates PureSpeech so that you can hear your calls in amazing clarity, but also so you can be heard clearly by your callers. PureSpeech is always activated on the EX7 so you will "Hear and Be Heard Like Never Before."

To dial a number, make sure that your headset is turned on, then dial the number from your phone. Your headset will activate as soon as the number is dialed. To voice dial a number (not supported on all phones), press send/end. A tone plays, which is your signal to speak the command or number. Know the facts Recharge time: About two hours Talk time: Up to eight hours Standby time: Up to 300 hours Phone pairing: Up to eight phones at the same time LEDs To... Do this... End a call Press send/end. Answer a call Press send/end. Redial a number Double-press send/end. Reject a call Double-press send/end. Switch a call between the headset and the phone. Mute a call Double-press send/end. 10-0723 4 Maintaining Press and hold the power button and send/end for about two seconds. To... Do this... Increase the volume Decrease the volume Swipe upward (toward the ear) on the touch pad.You will hear a diferent "beep" for each level change in volume. Swipe downward (away from the ear) on the outside of the headset. To... Enable or disable the indicator Check the battery level (method 1) Check the battery level (method 2) Erase paired device information Multipoint pairing (pairing the headset to multiple phones) Reset Disconnect from the phone (un-pair) Do this... Press the power button and send/end together. Turn the headset on, then press and release the power button. Green = Between 1/2 and full charge Green then red = Between 1 hour talk time remaining and 1/2 charge Red = Less than 1 hour talk time remaining. Turn the headset on. If the indicator fashes red and green, or if it beeps every 300 seconds, the battery level is low. Turn the headset of, then press and hold the power button and send/end together for about two seconds. Pair each phone with the headset. When you are in a call with one phone but the other phone rings, press send/end to switch to the second call. Connect the charger to reset the headset, then user can power on headset after remove the charger. Turn the headset of, then use the phone’s Bluetooth menu to disconnect it. For help with this step, see your cell phone’s user guide. Green Power On Green (fast fashing) Pairing State Red (fashing) Low Battery RF-EX7 EX7 WITH PURE SPEECH® Hear and be heard like never before © 2010 Best Buy Enterprise Services, Inc. Distributed by Best Buy Purchasing, LLC • 7601 Penn Avenue South, Richfield, MN USA 55423-3645 RFEX7 QUICK SETUP GUIDE FCC Part 15 This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. FCC ID: EMJTRFEX7 “You are cautioned that changes or modifcations not expressly approved by the part responsible for compliance could void the user’s authority to operate the equipment”. Canada IC-RSS210 statement IC: 4251A-HRFEX7 Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.