Robert Juliat Dalis-862S Quick Start Manual

Firmware V1.XX – 15/11/17 DN41136200 Robert Juliat S.A.S. 32, rue de Beaumont, F60530 Fresnoy-en-Thelle - phone : +33 (0)3 44 26 51 89 - fax : +33 (0)3 44 26 51 89 - [email protected] Dalis – 862S Footlight Projecteur bain de pied LED 75 W - Blanc variable LED 75 W - Variable White Footlight For more information, Please download the full manual online http://www.robertjuliat.com/ambiance_lighting/dalis862.html Package contents: 1x Dalis 862S 1x Neutrik PowerCon© True1 connector (ref. NAC3FX-W) Quick start guide

GENERAL INSTRUCTIONS 1. Not for residential use. 2. These fixtures must only be serviced by a qualified technician. 3. In addition to the instructions indicated on this page, relevant health and safety requirements of the appropriate EU Directives must be adhered to at all times. 4. This fixture is in compliance with section 17 - Lighting appliance for theatre stages, television, cinema and photograph studios. Standards NF EN 60598-1 and NF EN 60598-2-17. 5. This fixture is rated as IP20, and is for indoor use only. FIXTURE 6. Ensure fixture is correctly mounted on an appropriate support. 7. Protection screens must be replaced in the event of any damage, such as cracks or deep scratches, since these might reduce performance. 8. When hung or flown the fixture must be secured by an additional hanging accessory (such as a safety cable or bond) of suitable length 9. Safety bonds or cables must be securely attached to the fixture and be as short as possible, or rolled up as necessary, to minimise travel distance should the fixture be dislodged. 10. WARNING: LED source become hot during use. Allow fixture to cool before servicing. 11. Do not tamper with design of fixture nor any of its safety features. 12. Tighten electrical mains cable connections regularly and replace with one of identical specification if damaged. 13. Use only with correct power supply. 14. Do not orientate the fixture towards a source of light (sun, fixture), in particular for LED versions. VENTILATION 15. Keep well away from flammable material. 16. Not for outdoor use. Do not cover. Do not permit fixture to get wet. 17. To avoid overheating, do not obstruct air vents– do not cover the unit. PLEASE NOTE These products have been built to conform to European standards relating to professional lighting equipment. Any modification made to our products will void the manufacturers' warranty. 2 Installation Floor installation only

1 Power input : • Connector: Neutrik powerCON TRUE1 • Voltage: 90 à 264V 50/60Hz • Power consumption: 90 W max. 2 Power output: • Connector: Neutrik powerCON TRUE1 • Daisy chain: § 230 V: 30 units max § 120 V: 15 units max § 100 V: 12 units max 3 Data In: • Connector: XLR 5-pin • Protocol: USITT DMX 512-A / RDM 4 Data Out: • Connector: XLR 5-pin • Protocol: USITT DMX 512-A / RDM 5 Ethernet: • Connector: RJ45 • Protocol: Art-Net / sACN + software update 4 DMX control DMX address and control mode selection: Data Mode DMX DMX Address Start addresss : XXX Mode X : XXXXXXX Main screen Personality 1 2 4 3 5

DMX address Mode 1: Full4groupsmode 16b Mode 2: Full1groupmode 16b Mode 3: Full1groupmode 8b Mode 4: Presetmode 16b Mode 5: Presetmode 8b Mode 6: 4groupsindividual 16bits Mode 7: 4groupsindividualpreset 16b 1 Dimmer Dimmer - US Dimmer - US Dimmer Dimmer Dimmer - US1 Dimmer - 1 2 Dimmer fine Dimmer fine - US Cool white - US Dimmer fine Balance Dimmer fine - US1 Dimmer fine - 1 3 Cool white - US1 Cool white - US Warm white - US Balance CCT Cool white - US1 Balance - 1 4 Cool white fine - US1 Cool white fine - US Dimmer - DS CCT Strobe duration Cool white fine - US1 CCT - 1 5 Warm white - US1 Warm white - US Cool white - DS Strobe duration Strobe speed Warm white - US1 Blue position intensity - 1 6 Warm white fine - US1 Warm white fine - US Warm white - DS Strobe speed Response time Warm white fine - US1 Red position intensity - 1 7 Cool white - US2 Dimmer - DS Strobe duration Response time Control mode Dimmer - US2 Dimmer - 2 8 Cool white fine - US2 Dimmer fine - DS Strobe speed Control mode Blue position Dimmer fine - US2 Dimmer fine - 2 9 Warm white - US2 Cool white - DS Response time Blue position Red position Cool white - US2 Balance - 2 10 Warm white fine - US2 Cool white fine - DS Control mode Red position Position Intensity Cool white fine - US2 CCT - 2 11 Cool white - DS1 Warm white - DS Blue position Position Intensity Warm white - US2 Blue position intensity - 2 12 Cool white fine - DS1 Warm white fine - DS Red position Warm white fine - US2 Red position intensity - 2 13 Warm white - DS1 Strobe duration Position Intensity Dimmer - DS1 14 Warm white fine - DS1 Strobe speed Dimmer fine - DS1 15 Cool white - DS2 Response time Cool white - DS1 16 Cool white fine - DS2 Control mode Cool white fine - DS1 17 Warm white - DS2 Blue position Warm white - DS1 18 Warm white fine - DS2 Red position Warm white fine - DS1 19 Strobe duration Position Intensity Blue position intensity - 1 20 Strobe speed Red position intensity - 1 21 Response time Dimmer - DS2 22 Control mode Dimmer fine - DS2 23 Blue position Cool white - DS2 24 Red position Cool white fine - DS2 25 Position Intensity Warm white - DS2 26 Warm white fine - DS2 27 Blue position intensity - 2 28 Red position intensity - 2 Group 2 Group 1 US = Up Stage DS = Down Stage