Samsung 460UT Installation Manual

Introduction 02 Unpacking 02 Attaching the bracket � to the monitor 03 Mounting the bracket � onto a wall 06 Arranging the monitors 07 Fine tuning 10 Detaching the monitors Product specifications 11 Product specifications Product drawings 12 Product drawings 13 Drawings BN68-01537F.indb 1 2009-12-18 12:17:49

1. Be sure to contact an installation expert authorized by your dealer to perform the installation. • Installation by a non-professional may cause personal injury. If you are planning to relocate or replace the product after installation, be sure to consult with an installation expert authorized by your dealer. After installation, do not apply excessive force or physical pressure on the product. 2. Do not let your children play in the vicinity of the product. • They may bump their head or body against the corner of the product and suffer personal injury. 3. Be careful not to let the back of the product hit against the wall when it is rotated or the angle is adjusted. • You can protect the wall and product from any damage by attaching a piece of sponge to each corner of the product. 4. Do not install the product on a wall that cannot bear the weight of the product. • The product may fall, and get damaged or cause personal injury. 5. Products installed in unusual, abnormal or extreme areas may be subject to serious performance problems due to the surrounding environment. Be sure to consult with a Samsung service center before installing the product in such an area. • Areas exposed to an excessive amount of fine particles or moisture, chemicals, extreme temperatures, high humidity, automobiles, etc. The information contained herein is for your safety and to prevent any loss of property. Please read the instructions carefully to use the product correctly. This mandatory sign is used to emphasize the instructions that must be observed. Safety Precautions English - 1 BN68-01537F.indb 1 2009-12-18 12:17:49

Wall-mount bracket � Screw � (M8 X 60mm) : x4 Screw �� (M8 X 30mm) : x4 Coupler : x2 Screw holder: x4 Wood screw (M5 X 50mm) : x8 Safety fastener: x2 Screw � (M5 X 10mm) : x2 Attaching the bracket � to the monitor 1. Assemble the four screws � and the screw holders, and fasten them to fix the bracket � to the monitor as shown in the picture below. ] Warning Check to confirm that the bracket � is fastened to the monitor. English - 2 BN68-01537F.indb 2 2009-12-18 12:17:51

1. Fix the bracket � tightly against the wall using the wood screws. 1 2 3 4 5 6 7 8 As shown in the picture above, fasten in order from � to �. N If it is difficult to fasten the screws into the specific holes, fasten the screws in the adjacent holes. � Installing the Video Wall 3 4 1 2 N Installing the Video Wall should be done by two persons or more. N The couplers are only used to install a Video Wall in order to leave a gap between the monitors that make up the Video Wall. Do not use them when installing only one monitor. ] Warning 1. Before you install on the Video Wall, check the wall strength considering the total weight of the monitors and brackets you want to install. - Weight of a monitor: 30kg - Weight of a bracket: 7kg 2. If you intend to install on a Video Wall that is four layers or more, take into consideration the air conditioning system. Consult with an expert before installation as heat from the monitors may cause problems. ] Warning 1. Ensure you check the wall strength, and do the reinforcing work before installation if the wall is not sufficiently strong. 2. The provided screws are for wood. 3. Check the wall and use proper screws according to the material of the wall, such as marble, steel plate or concrete. � How to fasten a screw Make a hole using a 3X50 drill. Clean the inside of the drilled hole. Fasten the wood screw into the hole. � When drilling a hole into a wall, make sure you use a drill bit and drill of the specified diameter. Otherwise, there may be safety problems. English - 3 BN68-01537F.indb 3 2009-12-18 12:17:52

Fasten the two screws � into the bracket �. 3. To align horizontally, attach the bracket � to the couplers on the bracket � using the screws �. (Should be done by two persons or more.) After fixing tightly, attach the assembly to the wall following step 1. Fasten the screws tightly so that there is no space between the couplers and the bracket �. 4. To align vertically, insert the legs of the bracket � completely to the top of the bracket � to assemble the two brackets. English - 4 BN68-01537F.indb 4 2009-12-18 12:17:52

N Increase the number of brackets following the steps above. ] Warning As shown in the pictures, the bottom of the bracket � must be inserted fully into the top of the bracket �. English - 5 BN68-01537F.indb 5 2009-12-18 12:17:53

1. Hook the monitor to which the bracket � is attached on the poles of the wall-mount bracket �. ] Warning Be sure not to put pressure on the panel with your hands when handling the monitor. Otherwise, you may break the panel. 2. To prevent the monitor from becoming loose, fasten the safety fasteners using the screws �. Fasten them on both sides. ] Warning Ensure the hooks are suspended securely on the poles. English - 6 BN68-01537F.indb 6 2009-12-18 12:17:54

3. Arrange the monitor on each bracket following steps 1 and 2. ] Warning Be careful not to catch your finger during installation. Fine tuning N After arranging the monitors, if they do not seem well-proportioned, adjust them using the fine-tuning screws on the brackets. N Be sure not to leave any height differences or gaps between the monitors. English - 7 BN68-01537F.indb 7 2009-12-18 12:17:56

If you turn the fine-tuning screw clockwise or counterclockwise, the monitor will move forward or backward respectively. The fine-tuning screw’s maximum movement range is 10mm. Moving the monitor forward Moving the monitor backward 2. Correcting height difference between upper and lower monitors. If you turn the fine-tuning screw on the bottom of the monitor clockwise or counterclockwise, the monitor will move up or down respectively. Lowering the monitor Raising the monitor English - 8 BN68-01537F.indb 8 2009-12-18 12:17:57

� Move a monitor until a space large enough to accommodate your hand is created. � Rotate the monitor, unfold the holder attached to the bracket and fix the monitor in the holder. � Turn the fine-tuning screw to correct the height difference. � Repeat steps �~� till you obtain the optimum result. ]Warning 1.Be careful not to catch your fingers. 2.Ensure the holder is fastened to the monitor-mount bracket �. Fixing the monitor in the holder English - 9 BN68-01537F.indb 9 2009-12-18 12:17:58

1. Detaching the upper monitors Unfasten the screws fixing the safety fasteners and lift up the monitors from the video wall. 2. Detaching the lower monitors � Move the monitor you want to detach, and rotate and fix it in the holder. � Remove the safety fasteners from the monitor and lift up the monitor to detach it from the video wall as shown in the picture below. [ Caution Before detaching the monitors, ensure you disconnect all the cables connected to them. Fixing the monitor in the holder English - 10 BN68-01537F.indb 10 2009-12-18 12:18:00

1. Move the left and right monitors on the top layer until a space large enough to accommodate your hand is created. 2. Rotate the middle monitor to fix it in the holder. 3. Move the left and right monitors on the middle layer following step 1. 4. Lift up the middle monitor to detach it from the video wall. Product specifications Dimensions (mm) W955 X H590.5 X D93 Weight (kg) 7 VESA standard wall-mount (mm) 600 X 400 [ Caution For performance improvement, the product’s exterior and specifications are subject to change without prior notice. English - 11 BN68-01537F.indb 11 2009-12-18 12:18:00

English - 12 BN68-01537F.indb 12 2009-12-18 12:18:02

600 67 515 400 11.5 10.5 45 50 45 62.2 26 M8 X L60 2. Wall-mount bracket � 650 900 160 330 480 8 10 57 52 45 10 8 590.5 57 26.7 26 71 33 217 M8 X L60 English - 13 BN68-01537F.indb 13 2009-12-18 12:18:04

01 Consignes de sécurité Introduction 02 Déballage 02 Fixation du support � au moniteur 03 Montage du support � sur le mur 06 Disposition des moniteurs 07 Réglage de précision 10 Détacher les moniteurs Caractéristiques techniques du produit 11 Caractéristiques techniques du produit Schémas du produit 12 Schémas du produit 13 Schémas BN68-01537F.indb 1 2009-12-18 12:18:04