Rhydolabz eCee PIC 18F4580 Quick Start Manual

Document : Datasheet Model # : DEV - 1122 Date : 18-Apr-08 eCee PIC 18F4580 Development Board Quick Start Guide Rhydo Technologies (P) Ltd. (An ISO 9001:2008 Certified R&D Company) Golden Plaza, Chitoor Road, Cochin – 682018, Kerala State, India Phone : 0091- 484-2370444, 2371666 Cell : 0091-99466 70444 Fax : 0091- 484-2370579 E-mail : [email protected], [email protected] WebSite : http://www.rhydolabz.com

CONTENTS  OVERVIEW  eCee PIC18F4580 BOARD FEATURES  eCee PIC18F4580 PACKAGE CONTENTS  PIC18F4580 MICROCONTROLLER SPECIFICATIONS  FUNCTIONAL BLOCK  INTERFACE OVERVIEW  POWER SUPPLY  CLOCK SOURCE  SETTING UP eCee PIC18F4580  PROGRAMMING STEPS

eCee PIC18F4580 BOARD FEATURES The eCee-PIC18F4580 Development and Evaluation Board from RhydoLabz can be used to evaluate and demonstrate the capabilities of microchip PIC18F4580 microcontrollers. The board is designed for general purpose applications and includes a variety of hardware to exercise microcontroller peripherals. Ideally suitable for training and development purposes.  Compact and Ready to use design  Professional and Fully EMI/RFI Complaint PCB Layout Design for Noise Reduction  High Quality Two layer PTH PCB  Includes PIC18F4580 Microcontroller with built-in CAN Module  Board Supports PIC 16F877A/18F 4520/4550 Microcontrollers  No separate programmer required (Built in Boot loader)  No Separate power adapter required (USB power source)  Screw terminal for External power Supply (with Jumper Select Option)  External Power Supply range of 7V to 20V  Adaptor (any standard 9-12V power supply) option  RS-232 Interface (For direct connection to PC’s serial port)  On board Two Line LCD Display (2x16)  On board I2C EEPROM (4K-AT24C04)  On board I2C RTC (DS 1307) with Crystal and Battery  On board 32.768 KHz Crystal for RTC  Four multiplexed 7-Segment LED Display  Built in Matrix keyboard (12 keys)  Built in Pull-Up (4 Keys) Keyboard  Built in IR Sensor Interface – TSOP 1738  Built in 8 LED Interface to test I/O  On Board External Interrupt and Reset buttons  Built in Potentiometer interface for ADC  On Board Temperature Sensor Interface

eCee PIC18F4580 PACKAGE CONTENTS  On Board Buzzer Interface  On Board PWM Output pin  Screw terminal for CAN BUS (with Jumper Select Option)  On Board CAN Transceiver IC  On Board ICD Connector for Debugging/Programming  On Board ICSP Connector  On Board 20 MHz Crystal Oscillator  On Board Power LED Indicator  On Board DB9 Connector  On Board USB Connector  All Port Pins available at IDC (2x5) Connector  Power Supply Reverse Polarity Protection  On Board 1 Amp Voltage Regulator  Can be used as main board for developing applications  Demo HEX codes included for testing of board features  Example codes included  Fully Assembled and Tested eCee PIC18F4580 Development board  Software CDROM with o Schematic o Programming Software o Sample Hex Code o Example Codes for  Led Blinking LCD Display  Matrix Keyboard External Interrupt Interfacing  I2C Protocol 7-Segment Display  Led Control with Timer0 UART Communication  PWM Generation Buzzer Interfacing  ADC Interfacing Pull-Up Keyboard  Capture Module Compare Module  Timer 1 Timer 2  CAN Communication

PIC18F4580 SPECIFICATIONS  High Performance RISC CPU  32 KB Programmable Flash Memory  1536 bytes Data Memory (SRAM)  256 bytes EEPROM  Supports Up to 40 MHz Operation  36 I/O pins  11-Channel 10-bit Analog to Digital Converter(ADC)  One Capture module/ Compare Module/PWM Module  One Enhanced Capture Module/ Compare Module/ PWM module  One ECAN Module with Message bit rates up to 1 Mbps  Parallel Communications (PSP) Support  One 8-Bit Timer/Counter and Three 16-Bit Timer/Counter  One Enhanced USART (Supports RS-232, RS-485 and LIN 1.3)  One Master Synchronous Serial Port (MSSP)  One Serial Peripheral Interface(SPI) Module  One Inter-Integrated Circuit (I2C) Module  Power-On Reset (POR), Power-Up Timer (PWRT) and Oscillator Start-up Timer (OST)  Interrupt Capability (up to 20 sources)  Three External Interrupts  In-Circuit Serial Programming (ICSP) via two pins  In-Circuit Debug (ICD) via two pins  Self Programmable under software control  Programmable Brown Out Reset  Low Voltage Programming  Power Saving Sleep Mode  Extended WatchDog Timer(WDT)  Wide Operating Voltage 2.0V to 5.5V  Low Power Consumption using nanoWatt Technology

INTERFACE OVERVIEW LCD Module PIC 18F4580 IC BUZZER MAX232N RESET SWITCH PULL UP KEYBOARD IR SENSOR EXTERNAL POWER (7V-20V) VOLTAGE REGULATOR 3×4 MATRIX KEYBOARD USB POWER INTERFACE DB9 CONNECTOR (SERIAL INTERFACE) EXTERNAL EEPROM EXTERNAL INTERRUPT KEY LCD CONTRAST KNOB RJ-45 CONNECTOR LED ARRAY RTC BATTERY UNDER THE LCD SCREEN ADC KNOB TEMPERATURE SENSOR - LM35 CAN PORT (CANH and CANL) 7-SEGMENT DISPLAY ADAPTER PLUGIN PORTB PINOUTS PORTC PINOUTS PORTD PINOUTS CAN TRANSCEIVER IC PORTA and PORTE PINOUTS

POWER SUPPLY CLOCK SOURCE eCee PIC18F4580 Board has three power supplies; you can choose one of the following ways to supply power : (1) Through a Screw Terminal (7V - 20V External DC Power Supply) (2) Through the motherboard USB port (3) Through an adapter (7V - 20V External DC Power Supply) The Power Supply circuit is given below: eCee PIC18f4580 evaluation board has two clock sources:  32.768 KHz as the RTC clock source  20 MHz Crystal as the MCU clock source Vin 1 GN D 2 Vout 3 U3 LM7805 D- 1 VCC 2 D+ 3 GND 4 K1 USB 1 2 3 K2 POWER SELECTION +5 D9 1N4007 1 2 K3 CONN 2PIN C9 470MF/40V C5 0.1MF C6 0.1MF C10 47MF/16V R43 470R D10 PWR LED J1 DC POWER +12V DC USB DC

SETTING UP eCee PIC18f4580  Power the development board with a USB Cable.  Make sure that the Power-On LED is ON and the jumper is in proper position.  Connect the RS-232 Cable to the COM port of your computer.  Connect the other end to the Serial Port of your Demo Kit.

PROGRAMMING STEPS The PIC18F4580 Demo Kit is preloaded with Boot loader firmware. This allows the user to program the microcontroller without using separate programmer. 1. Setup Rhydo Boot Loader. 2. Select COM port and set Baud rate as 115200 bps. 3. Browse your Hex files. 4. Ensure RS-232 connection and power connection. 5. Click the Write Flash button. 6. Reset PIC using the Reset button while Boot loader searches for PIC. Note: The microcontroller is preloaded with boot-loader software. Programming with other devices/programmers or removing the microcontroller from the development board could damage the boot-loader. In this case, the company won’t be liable for the damages caused and no replacement/refunding/reloading is entertained.

TECHNICAL SUPPORT If you are experiencing a problem that is not described in this manual, please contact us. Our phone lines are open from 9:00 AM – 5.00 PM (Indian Standard Time) Monday through Saturday excluding holidays. Email can be sent to [email protected] LIMITATIONS AND WARRANTEES This product is intended for personal or lab experimental purpose and in no case should be used where it harmfully effect human and nature. No liability will be accepted by the publisher for any consequence of its use. Use of the product software and or hardware is with the understanding that any outcome whatsoever is at the users own risk. All products are tested for their best performance before shipping, still rhydoLABZ is offering One year Free service warranty (Components cost + Shipping cost will be charged from Customer). DISCLAIMER Copyright © Rhydo Technologies (P) Ltd All rights are reserved. Reproduction in whole or in part is prohibited without the prior written consent of the copyright owner. The information presented in this document does not form part of any quotation or contract, is believed to be accurate and reliable and may be changed without notice. Rhydo Technologies (P) Ltd. (An ISO 9001:2008 Certified R&D Company) Golden Plaza, Chitoor Road, Cochin – 682018, Kerala State, India Phone : 0091- 484-2370444, 2371666 Cell : 0091- 99466 70444 Fax : 0091 - 484-2370579 E-mail : [email protected], [email protected] WebSite : http://www.rhydolabz.com