Rexel Stack and Shred Auto+50 Instruction Manual

ON/OFF switch (at rear of machine) Important safety symbols (see shredder control panel below) Manual feed entry slot Credit card slot Reverse, auto, continuous jam boost switch (FWD) Paper loading door handle Paper loading door Power on indicator Cool down indicator Pull out bin with viewing window A B C D E F G H J I Introduction Thank you for choosing this shredder from Rexel. Please review these instructions to ensure you are operating the shredder correctly. Safety First To guard against injury, the following basic safety precautions must be observed in the set-up of this product. • Ensure the machine is plugged into an easily accessible power outlet, and ensure the cable is not likely to trip up a passer by. • invalidate the warranty. Please return to supplier. • Unplug your shredder before moving it or when it is not in use for an extended period of time. • Do NOT operate with a damaged power supply cord or plug, after it malfunctions, or after it has been damaged in any manner. • Do NOT overload electrical outlets beyond capacity as this can • The socket-outlet should be installed near the equipment and shall be easily accessible. • the appropriate electrical supply. • Do NOT use near water. • Do NOT use aerosol dusters or cleaners. • Do NOT spray anything into the shredder. • Do NOT load the autofeed chamber with unopened junk mail, magazines, bound documents etc. Although this shredder has been designed to comply with UL 60950 safety standards including the “probe accessibility tests”, do not operate the shredder near children or pets. Specifications Sheet capacity Manual feed slot Sheet capacity Autofeed chamber Duty cycle Run time from cold Volts / Hz Amperage Motor watts Rexel Stack and Shred Auto+50 5 sheets (80gsm) 50 sheets (80gsm) 6 min ON / 40 min OFF 8 minutes 230V / 50Hz 0.8 Amps 180 Watts Shredder Control Panel and Indicators Power On indicator – This means the machine is turned on. Cool Down indicator – This means the machine is cooling down. Auto Continuous Jam Boost Reverse Safety First This means no aerosols. This means you should be careful because long hair can become entangled in the cutting head. This means don’t reach into the feed opening of the cutting head. This means be careful of ties and other loose clothing which could become entangled in the cutting head. This means keep children away from shredder. This means be careful of loose jewelry which could become entangeld in the cutting head. This means the shredder cannot shred CDs or DVDs. This means no oil lubricant (oil sheets only). This means the shredder can accept small staples. This means the shredder can accept small paperclips. This means the shredder can accept credit cards. Sheet capacity of manual feed entry slot.

Auto+50 CAN shred the following: Auto+50 CANNOT shred the following: Although the Auto+50 will accept fastened sheets, Rexel recommends that staples and paper clips are removed prior to shredding to extend the life of the product. Stapled paper 1 inch/25mm within the corner Paper clip paper 1 inch/25mm within the corner 11x17 single sheet folded in half max. 2 sheets 80 gsm paper - Letter - 8.5x 11 - Legal - single sheet folded in half max. 2 sheets 26/6 and 24/6 or smaller staples Small sized paper loaded centrally 50 sheets colour printing >100gsm paper (through manual feed slot ONLY) Capable of shredding small/ medium (max wire thickness = 1/3 inch, 0.9 mm) paper clips 50 sheets plain paper 50 sheets single sided printed paper Heavy duty staples with a staple leg length greater than 6mm. A document with more than 25 sheets held together by a staple or clip. Bound documents Bulldog clips Large clips. Check the length of the paperclip is not longer than 32mm. Multiple folded sheets* (e.g. more than two legal sized sheets folded in half) Magazines or other documents bound by multiple staples or clips Unopened mail* e.g. junk mail. Open mail and place in auto-feed or feed through manual feed slot. Plastic sheets, laminated documents, plastic folders, glossy paper or a sheet covered with print on both sides. Thick paper or cardstock* * We recommend you feed these types of documents through the manual feed slot. Crumpled sheets* Lights and Icons Explained LED Illumination Cool Down Auto Colour of symbol Red Blue Power switch off Power switch on light Auto mode light Continuous Jam Boost mode light Reverse mode light Paper loading door open light Bin open light Motor cooling down light light Adhesive labels Standard Staples Standard Staples Heavy Duty Staples Heavy Duty Staples Standard Paper Clips Standard Paper Clips Single Folded Sheet Single Folded Sheet > 25 Sheets > 25 Sheets Large Clips Large Clips Multiple Folded Sheets Multiple Folded Sheets Magazines Magazines Unopened Mail Unopened Mail Plastic Sheets Plastic Sheets

first by looking through the viewing window and if full you should empty the bin. • Pull open the bin slowly to empty. • Push the empty bin back into place and the machine will resume shredding. Credit Card Shredding The Auto+50 can shred credit cards. Switch the shredder to auto mode and insert the credit card between the markings in the manual feed slot (see fig. 4). Only shred one credit card at a time. Rexel encourages customers to recycle shredded paper. Please note that shredded paper cannot be recycled if mixed with credit card shards. If recycling, please separate shredded paper and credit cards. Reverse Function 1 If you want to reverse paper out while shredding, use the reverse button ( ). 2 Reverse the paper out then turn the shredder off using the ON/OFF switch at the rear of the shredder. Remove the paper from the manual feed slot (if being used) or open the loading door, remove the remaining stack of paper, then pull the jammed paper free of the cutting mechanism. 3 To resume shredding return the slide switch to the auto position ( ) and turn on the machine by using the ON/OFF switch at the rear of the shredder. Operation 1 Unpack the product. 2 Plug the shredder in to a working outlet. 3 Ensure the ON/OFF switch on the back of the shredder is in the “ON” position, which will illuminate the LED bulb shown by the standby symbol ( ). 4 To start shredding, move the slide switch to the Auto position ( ) which sets the shredder into auto mode. You are now ready to shred. 5 To load the shredder, simply lift the loading door catch (see fig. 1) to open the loading door and insert documents. You can open the door further to 90 degrees for easier access if required. Load up to 50 sheets at a time into the feed chamber. Do NOT fill above the 50 MAX level, this could damage the shredder (see fig. 2). 6 The shredder will start the shredding cycle automatically ONLY after closing the loading door (see fig 1). If there is still paper in the autofeed tray after first attempt, open and re-close feed door a second time. 7 If you only have up to 5 sheets to shred, you can use the manual feed slot, provided the auto feed chamber is empty (see fig. 3). Rare Occasions of Jamming In the unlikely event of the shredder jamming, the Stack and Shred Auto+50 will stop shredding. Check that the bin is not full then try clearing the jam using the reverse ( ) and continuous jam boost ( ) switch then return to Auto mode ( ). If this is unsuccessful follow the reverse function instructions. Bin or Loading Door Open Safety Function As a safety precaution, if the bin or loading door is opened during shredding, the shredder will stop. Over Heating If the The Auto+50 is used continuously for over 8 minutes the shredder may overheat and the red cool down indicator will illuminate underneath the thermometer symbol ( ). Please allow the shredder to cool down. When the shredder is ready to be used the thermometer symbol will no longer illuminate. If the shredder needs to cool down while shredding, no action is needed. The shredder will automatically restart shredding paper once it has cooled down after periods of continuous use. All you need to do is ensure paper is loaded into the chamber and the bin is empty when the machine is cooling down. Autofeed Technology The Auto+50 has been designed to automatically shred up to 50 sheets from the autofeed chamber and up to 5 sheets through the manual feed slot. The autofeed mechanism has been designed to handle paper fastened with staples and paper clips and to only pull a few sheets of paper into the cutting mechanism to minimize the risk of paper jams.

time, please wipe clean with a dry cloth to maintain maximum product performance. The auto-start infra-red sensor, located in the paper feed entry- slot, can occasionally become covered in paper-dust causing the shredder to run despite no paper being fed into the machine. Switch the shredder off at the rear of the machine and carefully Accessory Part Number Box Qty Oil Sheets 2101949 20 sheets 2101948 12 sheets Lubrication of the Shredder Only use oil sheets to lubricate. ACCO Brands accepts no liability for product performance or safety when other types of lubricants are used on any part(s) of this machine. Insert the oil sheet into the manual feed slot and NOT in the autofeed chamber. Using an oil sheet in the autofeed chamber will contaminate the feed rollers preventing the auto-feed mechanism shredding. Follow the maintenance instructions if the rollers become contaminated. Do not directly oil the shredder. Guarantee ACCO Brands warrants its products and their parts against defects in materials and workmanship under normal use for a period of 24 months from the original date of purchase. During this period we will repair or replace a defective product or part subject to the following warranty conditions: The warranty applies only to defects in materials and workmanship under normal use and does not extend to damage to the product or parts which result from:- - anyone other than an authorised ACCO service centre. - accident, neglect, abuse or misuse owing to failure to comply with the normal operating procedures for a product of this type. Nothing in this warranty shall have the effect of excluding the liability of ACCO in respect of death and personal injury caused by the negligence of ACCO. This warranty is offered (subject to these terms and conditions) in addition to, and does not affect your statutory rights. For any questions relating to your warranty, please contact your local service agent (see back cover). Additional Warranty ACCO Brands guarantees the cutting blades of the shredder to be free from defects in material and workmanship for 5 years from the date of purchase by the original consumer. * Please note that the cutter blades will be progressively worn down by shredding fastened sheets (staples and paperclips) - this is not covered in the warranty. The Auto+50 has been design to shred up to 50 credit cards in the standard 2 year warranty period. Any excessive credit card shredding will invalidate the extended cutter warranty. Auto+50 has NOT been designed to shred CDs, any attempt to do so will invalidate this warranty. Australian Customers This guarantee does not apply to Australian customers. See warranty on page 7. 6

ACCO Australia warrants its products and their parts against defects in materials and workmanship under normal use for a period of 24 months from the original date of purchase (please retain proof of purchase). During this period we will repair or replace a defective product or part subject to the following warranty conditions: The warranty applies only to defects in materials and workmanship under normal use and does not extend to damage to ���������������������������������������� � ���������������������������������������������������������������������������������������������������������������� � �������������������������������������������������������������������������������������������������������������������� of this type. �������������������������������������������������������������������������������������������������������������������������� caused by the negligence of ACCO. This Warranty is offered (subject to these terms and conditions) in addition to, and does not affect your rights and remedies under,the Australian Consumer Law and other laws. Our goods come with guarantees that cannot be excluded under the Australian Consumer Law. You are entitled to a replacement or refund for a major failure and for compensation for any other reasonably foreseeable loss or damage. ��������������������������������������������������������������������������������������������������������������������������� does not amount to a major failure. ������������������������������������������������������������������������������������� Additional Guarantee ACCO Australia guarantees the cutting blades of the shredder to be free from defects in material and workmanship for an extended warranty period from the date of purchase by the original consumer. Please refer to the table below for the cutter warranty period applicable to your shredder model. ACCO Australia *Please note that the cutter blades will be progressively worn down by shredding fastened sheets (staples and ���������������������������������������������������������������������������������������������������������������������������� ������������������������������������������������������������������������������������������������������������������������ How to Make a Claim To make a claim under this warranty, contact the ACCO Australia Customer Service Team with your proof of original purchase handy: ACCO Australia ����������������������������������� Ph: 1300 366 376 ����������������������� F: 1300 360 944 The customer service team member will advise whether your product should be repaired, replaced or returned and advise the next step for you to take. If the product is validated as still under warranty and deemed faulty, ACCO will bear costs involved with the warranty process. To claim expenses incurred in making a claim under this warranty, contact our Customer Service Team on the details above. Shredder Models Extended Cutter Warranty Period Style, Style+, V35WS, V30WS, Alpha 3 Auto+60 5 ���������������������������������������������������������������������������������� CC175, Auto+80 7 V120, V125, P180CD, P185, RSS2030, RSX1630, RSS2232, RSX1632, RSM1130, Auto+100 10 Auto+250 15 RDS2250, RDX1850, RDSM750, RDM1150, RDS2270, RDX2070, RDSM770, RDM1170, Auto+500, RLS32, RLX20, RLM11, RLSM9, RLWX19, RLWX30, RLWSFM9, RLWM26, RLWX39, RLWS47, RLWX25, RLWS35 20 Auto+50, Auto+60

Oxford House Aylesbury HP21 8SZ United Kingdom www.accoeurope.com Ref: Auto+50/7148 Issue: 1 (07/11) Service LUX ACCO Service Division Hereward Rise, Halesowen, West Midlands, B62 8AN Tel: 0845 658 6600, Fax: 0870 421 5576 www.acco.co.uk/service . Acco Brands France SAS Service après-vente, ZAC Excellence 2000, 6 rue Robert Schuman, 21800 Chevigny Saint Sauveur Tel: +33 3 80 68 60 30, Fax: +33 3 80 68 60 49 [email protected] ACCO Deutschland GmbH & Co.KG Arnoldstrasse 5, 73614 Schorndorf, Germany Tel:+ 49 7181 887 120, Fax:+ 49 7181 887 198 info [email protected] ACCO Brands Iberia SL P Isaac Peral 19, 28820 Coslada (Madrid) Tel: 902 500 182 ext. 2, Fax: 91 309 6412 ACCO Brands Italia Srl Con Unico Socio Strada della Merla 49/B - P.O. Box 183 10036 Settimo Torinese (TO) Tel: +39 011 896 11 11,+39 800 848 616, Fax: +39 011 896 11 15 [email protected] ACCO Brands Benelux B.V Peppelkade 64, 3992AK Houten, Nederland/LesPays-Bas Tel: 0800-73362, Fax: 02-4140784 [email protected] , www.accobenelux.be ACCO Brands Benelux B.V Peppelkade 64, 3992AK Houten, Nederland/LesPays-Bas Tel: 0800-21132, Fax: 02-4140784 [email protected], www.accobenelux.be ACCO Brands Benelux B.V Peppelkade 64, 3992AK Houten, Nederland/LesPays-Bas Tel: 030-6346060, Fax: 030-6346070 [email protected], www.accobenelux.nl ACCO Brands Nordic AB Makadamgatan 5, 254 64 Helsingborg, Sweden Tel: +46 42 38 36 00, Fax: +46 42 38 36 10 [email protected] XERTEC a.s. Kloknerova 2278/24 (vchod z ulice Koštířova, budova CeWe Color - Fotolab) 148 00 Praha 4 - Chodov Tel: 225 004 411, Fax: 225 004 162 [email protected], http://www.xertec.cz ACCO Polska Sp. z o.o Al . Jerozolimskie 184, 02-486 Warszawa Te l.+48 22 570-18-29 , fax +48 22 570-18-33 www.acco. pl H OPI Customer Service CZ SK LV EST LT AUS RUS UA Tel: +359 2 80 99 166 [email protected] Представительство компании «АККО Дойчланд ГМБХ и КО . КГ» Россия 105005, Москва, Денисовский пер., д.26 Тел: (495) 933-51-63, Факс : (495) 933-51-64 DataLux Distribution Company 03151, Киев, Очаковская, 5/6, оф.110. 3 Tel: + 380 (44) 498 4956 ext. 2324, Fax: +380 (44) 275 9999 ACCO Australia Pty Ltd Level 2, 8 Lord Street, Botany, NSW, Australia, 2019 Tel: 1300 366 376 Fax: 1300 360 944 [email protected] ACCO Brands Schweiz GmbH Gewerbestrasse 8, CH-8212 Neuhausen a. Rheinfall Tel: +41 (0)52 674 01 74, Fax: +41 (0)52 674 01 75 info.ch@acc o.com ACCO-Rexel Ltd Clonshaugh Business & Technology Park, Clonshaugh, Dublin 17, Ireland Tel: 01 816 4300, Fa x: 01 816 4302 [email protected], www.accorexel.ie Crusher Road, Crown Ext.3, PO Box 102, Crown Mines, Johannesburg 2025, South Africa Tel: +27 (0) 11 837 7723 [email protected] ACCO Brands Asia Pte Ltd Rexel Office Products (PTY) Ltd 47 Ayer Rajah Crescent, #05-08/17, Singapore 139947 Tel: +65 6776 0195, Fax: +65 6779 1041 [email protected] GBC-Japan K.K. 14F Harmony Tower, 1-32-2 Honcho, Nakano-ku, Tokyo 164-8721 Tel: (81)-03-5351-1801, Fax: (81)-03-5351-1831 ser [email protected], www.gbc-japan.co.jp IRL IND PAK BD JPN ?