Kwikset Smartcode 914 Installation And User Manual

Begin with your smart home app If you will be using a smart home app with your lock, download the app and set up your controller or hub before proceeding further with lock installation. A N (2x) A A B B B A B If drilling a new door, use the supplied template and the complete door drilling instructions available at kwikset.com/doorprep 1-3/8" –2" 35 – 51 mm A B C D Is the door edge chiseled? Is the D-shaped hole centered in the door hole? Which latch are you installing? Hold the latch in front of the door hole, with the latch face flush against the door edge. 1" 25 mm YES YES NO NO Use latch “A”. If the latch bolt is not already extended, extend the latch bolt as shown. No adjustment is required. Proceed to next step. D-shaped hole D-shaped hole Rotate latch face as shown to extend latch. UP is on top. UP is on top. wood block Use latch “B” (not included). If the latch bolt is not already extended, extend the latch bolt as shown. Latch “A” Latch “B” door frame E Install the strike on the door frame. Make sure the hole in the door frame is drilled a minimum of 1" (25 mm) deep. or chiseled not chiseled or 1 2 3 Prepare the door and check dimensions Install the latch and strike or 2-3/8" or 2-3/4" 60 or 70 mm backset Measure to confirm that the backset is either 2-3/8" or 2-3/4" (60 or 70 mm). Measure to confirm that the hole in the door edge is 1" (25 mm). Measure to confirm that the door is between 1-3/8" and 2" (35 mm and 51 mm) thick. Remove your existing deadbolt from your door. C D E F B Latch “B” is not included. If needed, please contact Kwikset to order a drive-in latch for your lock. Strike C Keys E A B Exterior Assembly Adapter Ring D Mounting Plate Parts List Fasteners Interior Assembly SmartKey Tool H M F K L G Measure to confirm that the hole in the door is either 2-1/8" (54 mm) or 1-1/2" (38 mm). or 2-1/8" 54 mm 1-1/2" 38 mm Note: Additional door preparation may be required for doors with 1-1/2" (38 mm) holes. Consult the deadbolt drilling instructions at kwikset.com/doorprep A Make sure your door is compatible. If you have a standard deadbolt mounted separately from the handle below it, your door is compatible. Mortise Lock Not Compatible Not Compatible Rim Lock Compatible Not Compatible Integrated Interior 03809 46780 N Q S P 48654 64109 T V 49191 U S (2x) C Q (2x) Longer screws install closest to the door jamb. N P S Q actual size 66863-001 Rev 02 ZigBee Installation and User Guide Kwikset 1-866-863-6584 www.kwikset.com Batteries ENGLISH Required tools Ruler Hammer Wood block Chisel Phillips head screwdriver Additional Tools (depending on application) W

2-1/8" 54 mm 1-1/2" 38 mm K W actual size T K Green: Door handing was successful. Proceed to next step. Red: Door handing was unsuccessful. Make sure the lock interior and batteries are correctly installed. Perform step 6B again. If the bolt does not move, make sure the batteries are correctly installed, and perform step 6B again. What is the diameter of the hole in the door? Install 4 AA batteries in the battery pack. With the door open, press and HOLD the Lock button while installing the battery pack. Hold the button until the latch bolt starts moving on its own. The latch will retract and extend to learn the orientation of the door. The Status LED will indicate success or failure. Locate the screws for step 4C and keep them within reach. Install the exterior keypad and mounting plate. A A B C D B C Diameter is 2-1/8" (54 mm) Diameter is 1-1/2" (38 mm) or “D” is required for installation. Install “D” on “F”. “D” is not needed for installation. Discard “D”. The cable goes underneath the latch. Support the exterior assembly during mounting plate installation. Route the cable through the center hole, then push it into the bottom hole. Insert the key and test the latch. If the latch does not extend or retract smoothly, adjust the screws (T). Remove the key when finished, and make sure the latch bolt is fully extended. Keep parallel to the edge of the door. Tighten screws evenly. a c b d Note: The latch bolt will only retract half way. Ensure correct polarity. For best results, use new, non-rechargeable Alkaline batteries only. U actual size U (2x) Remove the interior cover and battery pack from the interior assembly. Install the interior assembly onto the mounting plate. A B a c b d Make sure the turnpiece is in the vertical position. Make sure turnpiece shaft is rotated as shown. Do not install batteries until step 6. Ensure tight cable connection. Lay the excess cable flat inside the bottom of the interior housing. align L a c b d bottom hole M L L L K D D F F G T T (2x) T E 4 Install the exterior keypad 5 Install the interior assembly 6 Install the batteries and perform the door handing process This step will teach your lock the orientation of your door and is crucial to lock operation.

1x green 3x red Initiate the pairing process through your smart home system (either through your smart home app, at your panel, or at your controller or hub). Refer to your smart home system instructions for more information. When prompted by your smart home system to initiate pairing at the lock, press button “A” on the lock interior four times. If the pairing process is successful, re-name the lock in your system (if applicable). If the pairing process is unsuccessful, press button “B” nine times. Perform steps 7A-7C again. If still unsuccessful, follow your smart home system's instructions to remove (exclude/unpair) the lock from any other network. Then perform steps 7A-7C again. A B C D Pair the lock with your smart home system button “A” button “B” Install the battery cover. M V (3x) a b IMPORTANT: Remove battery pack before re-keying. K H K a b c Re-key the lock to work with your existing key. See the supplied SmartKey Re-key instructions for more information. Reinstall battery pack. Optional: Re-key the lock. A B It is recommended that you add and delete all user codes through your smart home system. If your system does not allow this, codes may be added directly to the lock as shown here. One green flash with one beep Three red flashes with three beeps or Make sure the door is open. Press the Program button once. B Press the Lock button once. D What lights and sounds does the lock produce? E Enter a new user code. A total of 30 user codes may be programmed. C Each user code must be a unique code between 4 and 8 digits, depending on your smart home system. Programming was successful. Programming was unsuccessful. *Beeping sound will only be heard if switch #3 (on the lock interior) is in the on positon. Programming information Mastercode: For enhanced security, a mastercode may be used when adding and deleting user codes. For more information about the mastercode, download the SmartCode 914 Programming and Troubleshooting Guide at www.kwikset.com. Programming Timeout: During programming, if no button is pressed for five seconds, the system will time out (indicated by three beeps and a red flashing keypad), and you will need to restart the procedure. With the door open, press the Lock button. Confirm that the door locks. Enter the user code(s) added in the previous step. Confirm that the door unlocks. Close the door. Press the Lock button. Confirm that the door locks smoothly without error. If your does not lock smoothly, make sure you replaced your previous latch and strike with those supplied in the box. If you still experience locking errors, call Kwikset Support to order a Warped Door Service Kit. Kwikset Support: 1-866-863-6584 A A B C D Move swiftly through programming, as the system will time out if no button is pressed for five seconds. Make sure the user code is not a duplicate and that it is between 4 and 8 digits during your next attempt. Make sure the lock has room for an additional code. If all user code positions are filled, delete a code to make room for this one. V actual size 7 8 9 10 Add user codes (30 maximum) Re-key the lock (if needed) and install the battery cover Test the lock and check door alignment

one beep*. One incorrect code entered. Re-enter code. Keypad flashes red three times with three beeps*. No user code programmed. Program at least one user code. Programming timeout after five seconds. Attempt programming procedure again. Unsuccessful programming. Keypad flashes red 15 times with 15 beeps* Three incorrect codes entered within one minute. Re-enter code after 60 second keypad lockout. Keypad flashes red with fast beeping sound for three to four seconds. Low battery. Replace batteries. Keypad flashes red with continuous beeping sound for two seconds. Door jammed while attempting to lock. Manually re-lock door. If needed, reposition strike. Lock beeps continuously. Interior assembly is disconnected from exterior. Remove battery pack, reconnect the interior to the exterior, then reinstall battery pack. *Beeping sound will only be heard if switch #3 is on. 4 / 4 Removing the lock from the network Press button “B” on the lock interior nine times. © 2017 Spectrum Brands, Inc. 1. Read all instructions in their entirety. 2. Familiarize yourself with all warning and caution statements. 3. Remind all family members of safety precautions. 4. Protect your user codes and mastercode. 5. Dispose of used batteries according to local laws and regulations. CAUTION: Prevent unauthorized entry. Since anyone with access to the back panel can change the user codes, you must restrict access to the back panel and routinely check the user codes to ensure they have not been altered without your knowledge. The use of a mastercode can help protect your system’s settings. WARNING: This Manufacturer advises that no lock can provide complete security by itself. This lock may be defeated by forcible or technical means, or evaded by entry elsewhere on the property. No lock can substitute for caution, awareness of your environment, and common sense. Builder’s hardware is available in multiple performance grades to suit the application. In order to enhance security and reduce risk, you should consult a qualified locksmith or other security professional. Network Information Important Safeguards ZigBee System Notes ZigBee is a “Wireless mesh network,” and results may vary based on building construction and communication path, with 35+ feet being typical installed distance in a standard home environment and 250 feet+ when the lock has a clear line of sight with the smart home controller or hub. It may be necessary to install additional ZigBee devices to enhance the communication path between the lock and controller/ hub for a more robust ZigBee network. If no button is pressed for five seconds, the system will time out, and you will need to restart the procedure. 1 Keep door open. Press Program button once. 5 Re-enter user code. 6 Press Lock button once. If unsuccessful Make sure to enter the same valid code in steps 3 and 5. Test code While the door is open, test the user code to make sure it no longer unlocks the door. 2 Press Lock button once. 4 Press Lock button once. 3 Enter user code to be deleted. SmartCode at a Glance Deleting a single user code (manually at the lock) Note: All codes may be deleted at once if the mastercode is enabled. For more information about the mastercode, consult the SmartCode 914 Programming and Troubleshooting Guide at www.kwikset.com. Reference Guide Exterior Back panel Program button Status LED Switches Turnpiece shaft Note: When the cover is removed, the turnpiece shaft can be used to manually lock and unlock the door. These features can be adjusted in some smart home apps. Interior (cover removed) Switches and Status LED colors Troubleshooting Switch Function 1 Door lock status LED blinks every 6 seconds 2 Lock automatically re-locks door 30 seconds after unlocking. Disabled if no codes are programmed. 3 Audio 4 Not used. Color Lock Status Blinking green Unlocked Blinking amber Locked Blinking red Low battery Solid red Door handing process did not work properly. See the online Programing and Troubleshooting Guide. 1 2 3 4 On Switches Status LED Of System Alerts Factory Reset A factory reset will delete all codes associated with the lock, and it will remove it from your smart home system. Status LED 1 Remove battery pack. 2 Press and HOLD the Program button while reinserting the battery pack. Keep holding the button for 30 seconds until the lock beeps and the status LED flashes red. Keypad Lock button Keyway SmartKey tool hole Button “A” Button “B” 3 Press the Program button once more. When the LED flashes green and you hear one beep, the lock has been reset. 4 Perform the door handing process again to teach the lock the orientation of the door, pair the lock with your smart home system, and add user codes to your lock. A complete SmartCode 914 Programming and Troubleshooting Guide is available at www.kwikset.com.