Lorex Vantage LDC6011PK2 Quick Start Manual

VISIT WWW.LOREXTECHNOLOGY.COM Product Information User Manuals Quick Start Guides Specification Sheets Software Upgrades Firmware Upgrades Contents •�Indoor IR dome camera* •�Mounting screws x 3* •�60ft BNC / power extension cable* •�BNC female / RCA male adapter** •�Power adapter* 92mm / 3.6” Copyright © 2012 Lorex Technologies Inc. As our products are subject to continuous improvement, Lorex reserves the right to modify product design, specifications and prices, without notice and without incurring any obligation. E&OE Camera Specifications Image Sensor 1/3” Color Image Sensor Video Format NTSC Effective Pixels H: 720 V: 480 Resolution 600 TV Lines Scan System 2:1 Interlace Sync System Internal S / N Ratio 48dB (AGC Off) Iris AES AES Shutter Speed 1/60 ~ 1/25,000 sec. Min. Illumination 0.1 Lux without IR LED 0 Lux with IR LED Video Output Composite 1.0Vpp @ 75ohm Lens / Lens Type 3.6mm F2.0 / Fixed FOV (Diagonal) 78° Termination BNC Type IR LED Qty. / Type 10 pieces / 850nm Night Vision Range* 50ft / 15m Power Requirement 12V DC ±10% Power Consumption Max. 240mA (w / IR) Operating Temp. Range 14° ~ 122°F / –10° ~ 50°C Operating Humidity Range < 90% RH Environmental Rating** Indoor use only Weight (including stand) 0.4lbs / 0.2kg * IR Illumination Range under ideal conditions. Objects at or beyond this range may be partially or completely obscured, depending on the camera application. ** Not for outdoor use. WARNING - A REGULATED UL / CSA APPROVED power supply is REQUIRED for use with this camera. Use of a non-regulated, non-conforming power supply can damage this product and voids the warranty. Features •� Super resolution with enhanced optics delivering crystal clear video at 600TV lines of resolution •� BrightNight viewing with enhanced low-light image sensor •� Close-up recognition at night with auto-light compensation prevents wash-out effect •� Anti-glare feature ensures clear images under strong lighting conditions •� Accurate colors with Lorex’s automatic light filtering technology •� Night vision up to 50ft (15m) away in total darkness* •� See more with 3.6mm wide angle viewing lens (78° FOV)** Disclaimers: * Infrared illumination range under ideal conditions. Actual range and clarity may vary depending on scene / object reflection and camera application. ** Field of View, diagonal Warning/Caution •� Read this guide carefully and keep it for future reference •� Follow all instructions for safe use of the product and handle with care •� Use the camera within given temperature, humidity and voltage levels noted in Camera Specifications •� Do not disassemble the camera •� Do not point the camera directly towards the sun or a source of intense light •� Use only the supplied regulated power supply. Use of a non- regulated, non-conforming power supply can damage this product and voids the warranty •� Periodic cleaning may be required. Use a damp cloth only. Do not use harsh cleaners or aerosol cleaners. •� The supplied extension cable is rated for surface mounting only •� Cables for in-wall / floor-to-floor installations are sold separately Installation Tips •� This camera is for indoor use only •� Point the camera where there is the least amount of obstructions •� Install the camera in a location that is difficult for vandals to reach •� Secure cabling so that it is not exposed or easily cut SUPER RESOLUTION INDOOR NIGHT VISION DOME CAMERA Quick Start Guide English Version 2.0 LDC6011 SERIES 63mm / 2.4” Dimensions *Model LDC6011PK2 is a 2-pack that includes two of the listed items. ** Only included with single-camera configurations. ATTENTION - This camera includes an Auto Mechanical IR Cut Filter. When the camera changes between Day/Night viewing modes, an audible clicking noise may be heard from the camera. This clicking is normal, and indicates that the camera filter is working. 92mm / 3.6”

connect the extension cable to RCA inputs (i.e. for a TV connection). *Only included with single-camera configurations. BNC to RCA Adapter (Optional) To Camera: To Monitor/DVR: Male Power BNC Connect the BNC and power connectors to the camera Female Power Connect the BNC connector to the video input of the monitor / DVR, and connect the included power connector to a power adapter. See Setup Diagram below for details. Setup Diagram Camera Base Before installing the camera: •� Decide whether to run the cables through the wall / ceiling (drilling required) or along the wall / celing. •� If you run the cables along the wall / ceiling, you must run the cable through the cable notch on the base. This will keep the camera base flush to the wall / ceiling when mounted. To install the camera: 1. Twist the dome cover counterclockwise to loosen. Remove the dome cover. 2. Feed the BNC / power cable through the camera base. If you are running the cables against a wall or ceiling, make sure to pass the cable through the cable notch as shown above. 3. Mount the camera base to the wall or ceiling using the included screws. 4. Position the Ball Camera to the desired position and angle. 5. Position the dome cover over the ball camera and turn clockwise to lock into place. 6. Remove the protective film on the camera lens. Installing the Camera Connecting the Camera Cable Extension Options Extend the cable run for your camera up to 300ft or more depending on the cable type used. See table below: Option Cable Type Max Cable Run Distance Max # of Extensions 1 Regular BNC (supplied with camera) 180ft / 55m 3 2 ‘RG59’ or ‘Coax’ or ‘Coaxial BNC’ (sold seperately) 300ft / 92m 5 3 Lorex Universal Cable (sold seperately) 300ft / 92m 3 Notes: 1. For optimal performance, consider using option 2 or 3. It is best to use the same cable type for the entire distance. 2. Cable run recommendation based on typical camera power consumption (up to 500mA). For specialty cameras with higher current consumption, maximum cable run may be reduced. Consider providing power to the camera at the camera side, rather then at the end of the extension cable. 3. Indicators that your cable run may be too long: •� Video is permanently black & white (even during day time) •� Video is distorted ATTENTION - Test all connections and ensure the camera is working correctly prior to permanent installation by temporarily connecting the camera(s) and cable(s) to the viewing / recording solution. Problem Solution No picture / signal •�Ensure your TV is on the correct input channel. Common terms of an input channel: INPUT, AV CHANNEL, LINE1, LINE2, AUX. •�If your camera is connected to a VCR / DVR, ensure it is properly connected to your TV / Monitor. •�Ensure connections are properly connected. •�Ensure the camera power supply is plugged in. Picture is too bright •�Ensure your camera isn’t pointed directly at a source of light (e.g. sun or spot light). •�Slide the sunshade (bullet cameras featuring adjustable sunshades only) forward to block excess light. •�Move your camera to a different location. Picture is too dark •�If using during the day, the camera may not be getting enough light. Slide the sunshade (bullet cameras featuring adjustable sunshades only) backwards to let in more light. •�Check the brightness and contrast settings of the device your camera connects to (TV / Monitor / DVR). Night vision is not working •�The night vision activates when light levels drop. The area may have too much light. Picture is not clear •�Check the camera lens for dirt, dust, spiderwebs. Clean the lens with a soft, clean cloth. •�Make sure that the cable run is within the limitations specified in the section ‘Cable Extension Options’. Bright spot in video when viewing camera at night •�Night vision reflects when pointing a camera at a window. Move the camera to a different location. BNC connection does not connect to my TV. •�Use a BNC to RCA adapter at the end of the extension cable. Troubleshooting Note: To ensure the image is right-side up, make sure the triangle on the outer edge of the lens window points down.