National Semiconductor SD303EVK Operation & User’s Manual

LMH0303 / LMH0307 Evaluation Board User Guide National Semiconductor EVK User Manual February 3, 2010 Overview The SD303/SD307 Evaluation Kit (EVK) enables evaluation of the LMH0303 3G/HD/SD SDI Cable Driver with Cable Detect or the LMH0307 3G/HD/SD SDI Dual Cable Driver with Cable Detect. A graphical user interface allows managing the SMBus registers of the LMH0303 or LMH0307 device. Evaluation Kit (SD303EVK / SD307EVK) Contents The EVK contains the following parts: • SD303/SD307 EVK board assembly with either the LMH0303 or LMH0307 cable driver • USB cable • SD303/SD307 EVK User Guide Evaluation Board Description The evaluation board comes in two versions, depending on the cable driver installed: 1) SD303 with the LMH0303 cable driver 2) SD307 with the LMH0307 dual cable driver The two cable drivers share the same evaluation board (SD303/SD307). The SD303/SD307 evaluation board silk screen shows the LMH0307 pin name terminology. Table 1 shows the pin name differences between the LMH0307 and LMH0303. The LMH0303 has a single output channel, SDO/SDO ¯ ¯ ¯ ¯ . The LMH0307 has that same output channel and refers to it as SDO0/SDO0 ¯ ¯ ¯ ¯ ¯ . In addition, the LMH0307 adds a second output channel: SDO1/SDO1 ¯ ¯ ¯ ¯ ¯ . Table 1. LMH0307 and LMH0303 Pin Name Comparison Reference LMH0307 Name LMH0307 Description LMH0303 Name LMH0303 Description J3 SDO0 Channel 0 true output SDO True output J4 SDO0 ¯ ¯ ¯ ¯ ¯ Channel 0 complement output SDO ¯ ¯ ¯ ¯ Complement output J5 SDO1 Channel 1 true output J6 SDO1 ¯ ¯ ¯ ¯ ¯ Channel 1 complement output D9 TF0P SDO0 Termination Fault TFP SDO Termination Fault D10 TF0N SDO0 ¯ ¯ ¯ ¯ ¯ Termination Fault TFN SDO ¯ ¯ ¯ ¯ Termination Fault D8 TF1P SDO1 Termination Fault D7 TF1N SDO1 ¯ ¯ ¯ ¯ ¯ Termination Fault Figure 1 shows the SD303/SD307 evaluation board. SD303/SD307 EVK User Guide 1 of 27 Rev 1.2 © 2010, National Semiconductor Corp.

SD303/SD307 EVK User Guide 2 of 27 Rev 1.2 © 2010, National Semiconductor Corp.

The SDI input connectors (J1 and J2) are 50Ω SMA connectors. The SD303/SD307 is initially configured for 100Ω differential input. To configure the SD303/SD307 for 50Ω single-ended input, remove R28 and place 49.9Ω 0402 resistors in R9 and R10. When using only one input, the other input should be terminated with a 50Ω SMA termination. The SDO output connectors (J3 and J4 for the SD303; and J3, J4, J5, and J6 for the dual output SD307) are 75Ω BNC connectors. When using only one side of an output pair, the other side should be terminated with a 75Ω BNC termination. For example, when only using SDO0 on the LMH0307, SDO0 ¯ ¯ ¯ ¯ ¯ should be terminated with a 75Ω BNC termination. DC Power Connectors and USB Connector The red and black binding posts (J8 and J9) provide power for the LMH0303/LMH0307 device, and the USB connection provides power for the remaining board functions, including the microcontroller and the LEDs. For proper operation, the SD303/SD307 should first be powered with a DC input voltage (between J8 and J9) of 3.3V ± 5% (3.6V maximum), and then the USB cable should be connected between the evaluation board and the PC. The POWER LED will flash Red while the board is powered from the 3.3 VDC supply alone, and then change to solid Green once the USB cable is connected to the PC. The POWER LED will remain Green as long as the board is powered correctly. JP1 – LMH0303/LMH0307 Jumper Connection to Microcontroller A jumper block should be placed on JP1 to connect the LMH0303/LMH0307 pins to the microcontroller. The ALP software will not function correctly if this jumper block is not in place. Separate jumpers may be used, but they must be placed to connect the following pins of JP1: RSTI ¯ ¯ ¯ ¯ (pins 5-6), ENABLE (pins 7-8), SDA (pins 9-10), SCL (pins 11-12), SD/HD (pins 13-14), FAULT ¯ ¯ ¯ ¯ ¯ ¯ (pins 15-16), and RSTO ¯ ¯ ¯ ¯ ¯ (pins 17-18). This jumper block (or individual jumpers) may be removed to control the LMH0303/LMH0307 pins externally, but then the microcontroller will no longer be able to communicate with the cable driver. Controls and Indicators ENABLE The ENABLE push button switch controls ENABLE, and the ENABLE LED shows its state. The ENABLE LED is Green when the cable driver is enabled (ENABLE = 1), and Red when the cable driver is disabled (ENABLE = 0). When the cable driver is disabled, it enters a deep power down mode, and Termination Fault detection and LOS ¯ ¯ ¯ ¯ detection no longer function. If the LOSEN register bit (bit 4 of register 05h) is set, then the cable driver can be disabled with LOS ¯ ¯ ¯ ¯ detection still functioning. With LOSEN set, LOS ¯ ¯ ¯ ¯ is combined with the ENABLE functionality. In this mode, disabling the device by pushing the ENABLE switch will still power down the device completely (including powering down Termination Fault detection and LOS ¯ ¯ ¯ ¯ detection), but if ENABLE is left active and the signal is removed from the input, the device will power down with the LOS ¯ ¯ ¯ ¯ detection still functioning. When the input signal is reapplied, the device will power back on. SD/HD The SD/HD push button switch controls SD/HD, and the SD/HD LED shows its state. The SD/HD LED is Green when the cable driver is configured for HD/3G edge rates (SD/HD = 0), and Red when the cable driver is configured for SD edge rates (SD/HD = 1). The default setting for the SD/HD LED is Green for HD/3G edge rates. SD303/SD307 EVK User Guide 3 of 27 Rev 1.2 © 2010, National Semiconductor Corp.

The RSTI ¯ ¯ ¯ ¯ push button switch controls RSTI ¯ ¯ ¯ ¯ , and the RSTI ¯ ¯ ¯ ¯ LED shows its state. RSTI ¯ ¯ ¯ ¯ is used to reset the cable driver to its default register settings. The RSTI ¯ ¯ ¯ ¯ LED is Green during normal operation (RSTI ¯ ¯ ¯ ¯ = 1), and Red when the cable driver is held in reset (RSTI ¯ ¯ ¯ ¯ = 0). To reset the device, the RSTI ¯ ¯ ¯ ¯ switch must be pushed twice to fully toggle reset: once to put the device in reset mode (RSTI ¯ ¯ ¯ ¯ = 0), and again to resume normal operation (RSTI ¯ ¯ ¯ ¯ = 1) with the default register settings. RSTO ¯ ¯ ¯ ¯ ¯ The RSTO ¯ ¯ ¯ ¯ ¯ LED shows the state of RSTO ¯ ¯ ¯ ¯ ¯ . The RSTO ¯ ¯ ¯ ¯ ¯ LED is normally Red to indicate RSTO ¯ ¯ ¯ ¯ ¯ = 0. RSTO ¯ ¯ ¯ ¯ ¯ is the reset output used when daisy chaining multiple cable drivers on the same SMBus. After writing a new device address to register 00h (the ID register), the RSTO ¯ ¯ ¯ ¯ ¯ LED changes to Green to indicate RSTO ¯ ¯ ¯ ¯ ¯ = 1. RSTO ¯ ¯ ¯ ¯ ¯ remains high until the device is reset with RSTI ¯ ¯ ¯ ¯ . Termination Faults (TFxx) The Termination Fault LEDs show the state of the Termination Faults on the cable driver outputs. The Termination Fault LEDs are Green to indicate proper termination, Red to indicate improper or missing termination, and off to indicate the Termination Faults are not valid under the current cable driver conditions. The cable driver must be enabled and must have a valid input signal in order to properly detect cable termination on the output. If no signal is detected and the LOS ¯ ¯ ¯ ¯ LED is Red, then the Termination Fault detectors (TF1P, TF1N, TF0P, and TF0N for the LMH0307) cannot determine the state of the output termination and the LEDs will be off. When a valid input signal is applied, the Termination Fault detectors will show the correct state of their termination. If the cable driver is disabled or if the output channel is powered down, the Termination Fault LEDs will be off. LOS ¯ ¯ ¯ ¯ The LOS ¯ ¯ ¯ ¯ LED shows the status of the input signal detector. The LOS ¯ ¯ ¯ ¯ LED is Green to indicate a valid input signal (LOS ¯ ¯ ¯ ¯ = 1), and Red when no signal is detected (LOS ¯ ¯ ¯ ¯ = 0). When the cable driver is disabled (ENABLE = 0), the LOS ¯ ¯ ¯ ¯ detection is disabled as well and the LOS ¯ ¯ ¯ ¯ LED will be Red to indicate no signal can be detected. If the LOS ¯ ¯ ¯ ¯ LED is Red, then the Termination Fault detection does not function and the TFxx LEDs are forced off. With the LOSEN register bit (bit 4 of register 05h) set, the LOS ¯ ¯ ¯ ¯ detection may still function while the cable driver is disabled. In this mode, LOS ¯ ¯ ¯ ¯ is combined with the ENABLE functionality, and if the input signal is removed then the cable driver will power down but keep the LOS ¯ ¯ ¯ ¯ detection running. The device will power back on once an input signal is detected. (While in this mode, disabling the device by pushing the ENABLE switch will still power down the device completely, including powering down Termination Fault and LOS ¯ ¯ ¯ ¯ detection). LEDs and Push Button Switches Summary Table 2 shows a summary of the LEDs provided to assist the user in determining the configuration of the board, and Table 3 shows a summary of the push button switches provided to allow control of the board functions. SD303/SD307 EVK User Guide 4 of 27 Rev 1.2 © 2010, National Semiconductor Corp.

LED Reference Default after Reset * Function when GREEN Function when RED Function when OFF D1 POWER Green POWER=1, board powered When flashing Red, indicates the 3.3 VDC supply is connected but the USB is not Board not powered D2 ENABLE Green ENABLE=1, device enabled ENABLE=0, device powered down N/A D3 SD/HD Green SD/HD=0, HD/3G mode SD/HD=1, SD mode N/A D4 MODE Off N/A N/A No function, LED always off D5 RSTO ¯ ¯ ¯ ¯ ¯ Red RSTO ¯ ¯ ¯ ¯ ¯ =1 RSTO ¯ ¯ ¯ ¯ ¯ =0 N/A D6 RSTI ¯ ¯ ¯ ¯ Green RSTI ¯ ¯ ¯ ¯ =1, normal operation RSTI ¯ ¯ ¯ ¯ =0, device held in reset N/A D7 TF1N Off TF1N=0, SDO1 ¯ ¯ ¯ ¯ ¯ properly terminated TF1N=1, Termination Fault on SDO1 ¯ ¯ ¯ ¯ ¯ Termination Fault not valid (channel is powered down or no input signal detected) D8 TF1P Off TF1P=0, SDO1 properly terminated TF1P=1, Termination Fault on SDO1 Termination Fault not valid (channel is powered down or no input signal detected) D9 TF0P Off TF0P=0, SDO0 properly terminated TF0P=1, Termination Fault on SDO0 Termination Fault not valid (channel is powered down or no input signal detected) D10 TF0N Off TF0N=0, SDO0 ¯ ¯ ¯ ¯ ¯ properly terminated TF0N=1, Termination Fault on SDO0 ¯ ¯ ¯ ¯ ¯ Termination Fault not valid (channel is powered down or no input signal detected) D11 LOS ¯ ¯ ¯ ¯ Red LOS ¯ ¯ ¯ ¯ =1, signal detected at input LOS ¯ ¯ ¯ ¯ =0, no input signal detected N/A * Shows the default value after the board is reset (or initially powered on) with no input signal. Table 3. SD303/SD307 Push Button Controls Control Reference Description S1 SAVE No function. S2 RESET ¯ ¯ ¯ ¯ ¯ ¯ Push to completely reset the board, device, and ALP software. S3 ENABLE Toggles ENABLE. Push to set ENABLE=0 and power down the device. Push again to set ENABLE=1 and re-enable the device. S4 SD/HD Toggles SD/HD. Push to set SD/HD=1 and enable SD mode. Push again to set SD/HD=0 and enable HD/3G mode. S5 MODE No function. S6 RSTI ¯ ¯ ¯ ¯ Toggles RSTI ¯ ¯ ¯ ¯ . Push once to set RSTI ¯ ¯ ¯ ¯ =0 and reset the device. Push again to set RSTI ¯ ¯ ¯ ¯ =1 and return to normal operation following the reset. SD303/SD307 EVK User Guide 5 of 27 Rev 1.2 © 2010, National Semiconductor Corp.

USB: 2.0 Installation Download the latest software from http://www.national.com/analog/interface/sd303_307evk. Extract the ALPF_monthdayyear_major version_minor version.exe” (ex. ALPF_07312008_125_0016.exe) file to a temporary location that can be deleted later. Make sure the evaluation board is not connected to the PC. The following installation instructions are for the Windows XP Operating System. Install the ALP software Execute the ALP Setup Wizard program called “ALPF_monthdayyear_major version_minor version.exe” (ex. ALPF_07312008_125_0016.exe) that was extracted to a temporary location. There are 7 steps to the installation once the setup wizard is started: 1. Select the “Next” button. 2. Select “I accept the agreement” and then select the “Next” button. 3. Select the location to install the ALP software and then select the “Next” button. 4. Select the location for the start menu shortcut and then select the “Next” button. 5. There will then be a screen that allows the creation of a desktop and Quick Launch icon. After selecting the desired choices select the “Next” button. 6. Select the “Install” button, and the software will then be installed to the selected location. 7. Uncheck “Launch Analog LaunchPAD” and select the “Finish” button. The ALP software will start if “Launch Analog LaunchPAD” is checked, but it will not be useful until the USB driver is installed. Power on the SD303/SD307 evaluation board with a 3.3 VDC power supply. Numerous LEDs will turn on, and the POWER LED will flash Red. Connect the PC and the SD303/SD307 evaluation board together with the USB cable. The POWER LED will stop flashing, and the “Found New Hardware Wizard” will open on the PC. Proceed to the next section to install the USB driver. Install the USB driver There are 6 steps to install the USB driver: 1. Select “No, not at this time” then select the “Next” button. 2. Select “Install from a list or specific location” then select the “Next” button. 3. Select “Search for the best driver in these locations”. Uncheck “Search removable media” and check “Include this location in the search”. 4. Browse to the Install Directory which is typically located at “C:\Program Files\National Semiconductor Corp\Analog LaunchPAD\vx.x.x\Drivers” and select the “Next” button. Windows should find the driver. 5. Select “Continue Anyway”. 6. Select the “Finish” button. The software installation is complete. The POWER LED on the board should turn to solid Green. The ALP software may now be launched, as described in the next section. SD303/SD307 EVK User Guide 6 of 27 Rev 1.2 © 2010, National Semiconductor Corp.

“Analog LaunchPAD” from the start menu. The default start menu location is “Programs\National Semiconductor Corp\Analog LaunchPAD vx.x.x\Analog LaunchPAD”. The application should come up in the state shown below (for the LMH0307). If it does not, see “Trouble Shooting” at the end of this document. Figure 2. ALP Startup Screen for LMH0307 LMH0303/LMH0307 Profiles There are separate profiles for the LMH0303 and the LMH0307. The ALP software automatically detects which device is connected and configures the profile accordingly. There are four application tabs for the LMH0303/LMH0307 device. Information Tab The Information tab is shown in Figure 3 (for the LMH0307). SD303/SD307 EVK User Guide 7 of 27 Rev 1.2 © 2010, National Semiconductor Corp.

LMH0303 and LMH0307 Tab The LMH0303/LMH0307 tabs present a high level view of the cable driver. Figure 4 shows this tab for the LMH0307, and Figure 5 shows this tab for the LMH0303. SD303/SD307 EVK User Guide 8 of 27 Rev 1.2 © 2010, National Semiconductor Corp.

Figure 5. LMH0303 Main Tab SD303/SD307 EVK User Guide 9 of 27 Rev 1.2 © 2010, National Semiconductor Corp.

FW Ver shows the version of the firmware installed on the evaluation board. Termination Fault These controls show the default configuration of the HD and SD Termination Fault Threshold registers and also provide the ability to change the thresholds. The LMH0307 has two pairs of Termination Fault Threshold registers – one HD/SD pair for each of its two output channels – as shown in Figure 4. The LMH0303 has only one HD/SD pair of Termination Fault Threshold registers for its single output channel, as can be seen in Figure 5. Increasing the Termination Fault Threshold settings decreases the cable driver’s sensitivity to Termination Faults. This is useful if the cable driver is indicating termination faults when the output appears to be properly terminated. Decreasing the Termination Fault Threshold settings increases the cable driver’s sensitivity to Termination Faults which is useful for determining cable detection at the end of long cables. Compare Command and Termination Fault Counters Compare Command configures the CMPCMD section of the TEST register (08h) on the LMH0303 or LMH0307. The Termination Fault Counters reflect the current configuration of the TEST register CMPCMD bits. The Termination Fault Counters provide an indication of how the cable driver is reading the Termination Faults based on the current Termination Fault Threshold settings. Perfectly terminated outputs should read back “0”, and unterminated outputs should read back “31”. Control Refresh The Refresh button provides a manual refresh of the state from the evaluation board to the LMH0303/LMH0307 tab. Changes to the board will not be reflected in the LED icons and Line Control checkboxes on the LMH0303/LMH0307 tab until the Refresh button is pressed. This can be done automatically by using the Auto Refresh checkbox. Auto Refresh Checkbox The Auto Refresh checkbox provides an automatic refresh of the state from the evaluation board to the LMH0303/LMH0307 tab once per second. This provides automatic updating of the LED icons and Line Control checkboxes on the LMH0303/LMH0307 tab to reflect any board changes. Line Control Power Down 0 and 1 (LMH0307 only) Power Down 0 and 1 checkboxes control the PD0 and PD1 power down bits (bits 5 and 6 in register 02h - MASK) and will selectively power down one or both of the output channels on the LMH0307. Enable The Enable checkbox controls the associated ENABLE pin on the LMH0303/LMH0307. Disabling or un-checking the Enable checkbox will force the LMH0303/LMH0307 into a deep power down mode. RSTI The RSTI checkbox controls the RSTI ¯ ¯ ¯ ¯ pin. This checkbox is checked for normal operation, and un-checked to put the cable driver in reset. SD303/SD307 EVK User Guide 10 of 27 Rev 1.2 © 2010, National Semiconductor Corp.

HD/3G mode. Enabling this checkbox sets the cable driver edge rates to SD mode. SDO Amp The SDO Amp controls set the amplitude of the output driver(s). The LMH0307 has two independently configurable outputs (SDO0 and SD01) and the LMH0303 has a single configurable output (SDO). For the LMH0307, SDO Amp 0 configures the AMP0 bits in the OUTPUT0 register (04h), and SDO Amp 1 configures the AMP1 bits in the OUTPUT1 register (06h). For the LMH0303, SDO Amp configures the AMP bits in the OUTPUT register (04h). The default amplitude setting is 0x10 for 800 mVP-P. The output amplitude may be lowered to around 720 mVP-P and increased to around 880 mVP-P in roughly 5 mV increments. LED Icons The diagram of the LMH0303/LMH0307 device is framed by a number of colored LED icons that represent the LED state on the board. Note that either the Refresh button or the Auto Refresh checkbox must be used to update the LED icons in the LMH0303/LMH0307 tab to reflect any board changes. FAULT LED The FAULT LED shows the current state of the FAULT ¯ ¯ ¯ ¯ ¯ ¯ pin. The FAULT LED is Green to indicate no faults are detected (FAULT ¯ ¯ ¯ ¯ ¯ ¯ = 1) and Red to indicate one or more faults have been detected (FAULT ¯ ¯ ¯ ¯ ¯ ¯ = 0). The Auto Refresh checkbox should be checked in order to actively monitor the state of the FAULT ¯ ¯ ¯ ¯ ¯ ¯ pin. FAULT ¯ ¯ ¯ ¯ ¯ ¯ is triggered and set low for a Termination Fault on any output or the loss of signal on the input. FAULT ¯ ¯ ¯ ¯ ¯ ¯ is cleared and set high again when the faults have been removed by either terminating the outputs, applying the input signal, or changing the register settings in the MASK or DIRECTION registers. Registers Tab The Registers tab displays all registers for the LMH0303 or LMH0307. Figure 6 shows the Registers tab for the LMH0307. The Value field indicates the value of the currently selected register. SD303/SD307 EVK User Guide 11 of 27 Rev 1.2 © 2010, National Semiconductor Corp.

Each register can be examined in detail by either double clicking on the desired registers fold bar (with the address and the register name, e.g. 0x00 – ID) or by single clicking the icon at the right of the fold bar (two inverted carats). The Refresh button will re-read the currently selected register and the Refresh All will read all registers in the device. Changes may be made to the registers by checking or un-checking the individual register bits or typing in a new register value in the Value field. After setting the appropriate register value, the Apply button must be pressed to apply the changes. The detailed view of the STATUS register is shown in Figure 7 with Verbose Descriptions checked and Figure 8 with Verbose Descriptions un-checked. SD303/SD307 EVK User Guide 12 of 27 Rev 1.2 © 2010, National Semiconductor Corp.

Figure 8. LMH0307 Registers Tab without Verbose Descriptions The Display button provides another view of the register set and is depicted in Figure 9. The Display dialog supports the Windows copy command (Ctrl+c). SD303/SD307 EVK User Guide 13 of 27 Rev 1.2 © 2010, National Semiconductor Corp.

The Load and Save buttons provide a handy mechanism for restoring or saving the register set external to the evaluation board. Cable Driver Output Waveform Test Conditions The SDO0 output of the LMH0307 on the SD307 is observed in the following example. The input signal is a 2.97 Gbps PRBS10 from the Agilent 86130A 3.6G BERT. The input signal is connected differentially to the SDI SMA inputs on the evaluation board with matched 3’ SMA cables. The LMH0307 is running in HD/3G mode (SD/HD=0). The SDO0 output is connected through 1m of Belden 1694A cable to the TCA75 input module on the Tektronix DSA 71254 12.5 GHz Oscilloscope. SDO0 ¯ ¯ ¯ ¯ ¯ is terminated with a 75Ω BNC terminator. Test Results Figure 8 shows the typical SDO0 output waveform from the LMH0307. SD303/SD307 EVK User Guide 14 of 27 Rev 1.2 © 2010, National Semiconductor Corp.

SD303/SD307 EVK User Guide 15 of 27 Rev 1.2 © 2010, National Semiconductor Corp.

Figure 11. Analog LaunchPAD No Devices Error It may also be that the USB driver is not installed. Check the device manager. There should be an ”NSC ALP Nano Atmel” device under the “Universal Serial Bus Controllers” as shown below in Figure 12. Figure 12. Windows XP, Analog LauchPAD USB Driver SD303/SD307 EVK User Guide 16 of 27 Rev 1.2 © 2010, National Semiconductor Corp.

devices then the software is most likely in demo mode. When the ALP is operating in demo mode there is a “(Demo Mode)” indication in the lower left of the application status bar as shown in Figure 13. Figure 13. Analog LaunchPAD in Demo Mode Disable the demo mode by selecting the “Preferences” pull down menu and un-checking “Enable Demo Mode”. Figure 14. Analog LaunchPAD Preferences Menu After demo mode is disabled, the ALP software will poll the ALP hardware. The ALP software will update and have only “LMH0303” or “LMH0307” under the “Devices” pull down menu. SD303/SD307 EVK User Guide 17 of 27 Rev 1.2 © 2010, National Semiconductor Corp.

SD303/SD307 EVK User Guide 18 of 27 Rev 1.2 © 2010, National Semiconductor Corp.

Reference Designator Qty Description Manufacturer Manufacturer Part No. C1, C2 2 1uF Capacitor Ceramic 10V, 20%, X5R, 0402 Panasonic ECJ-0EB1A105M C3, C4, C5, C6, C10, C11, C14, C24, C26, C28 10 4.7uF Capacitor Ceramic 6.3V, 20%, X5R, 0603 Panasonic ECJ-1VB0J475M C7, C25, C27, C29 4 100pF Capacitor Ceramic 50V, 5%, C0G, 0603 Panasonic ECJ-1VC1H101J C8, C30, C31 3 0.1uF Capacitor Ceramic 50V, 10%, X7R, 0603 Panasonic ECJ-1VB1H104K C9 1 10uF Capacitor Ceramic 6.3V, 20%, X5R, 0603 Panasonic ECJ-1VB0J106M C12 1 0.033uF Capacitor Ceramic 50V, 10%, X7R, 0603 Panasonic ECJ-1VB1H333K C13, C15, C20, C21, C22, C23 6 1uF Capacitor Ceramic 16V, 10%, X5R, 0603 Panasonic ECJ-1VB1C105K C16, C17 2 12pF Capacitor Ceramic 50V, 5%, C0G, 0603 Panasonic ECJ-1VC1H120J C18, C19 2 220nF Capacitor Ceramic 10V, 10%, X5R, 0603 Panasonic ECJ-1VB1A224K D1, D2, D3, D4, D5, D6, D7, D8, D9, D10, D11 11 BiColored LED (Green, Red) LITE-ON LTST-C155KGJRKT D13 1 Bidrectional ESD Transient Supressor, SOT23-6 COMCHIP CEBS0624V-G D14 1 Diode Schottkey Array, 40V, SOT363 Diodes Inc BAS40DW-05-7-F J1, J2 2 SMA Connector (Edge Launch) Johnson Components 142-0701-851 J3, J4, J5, J6 4 75 ohm BNC (Edge Launch) Trompeter UCBJE20-1 J7 1 USB Mini-B Recept, R/A, 5POS Molex 54819-0572 J8 1 Binding Post (Banana Jack) Red Emerson 111-0702-001 J9 1 Binding Post (Banana Jack) Black Emerson 111-0703-001 JP1 1 10x2 Header, 0.100" spacing Tyco Electronics 87215-7 JP2 1 7x2 Header, 0.100" spacing Tyco Electronics 87215-4 L1, L2, L3, L4 4 6.8nH Inductor, 0402 Murata LQP15MN6N8B02D Q1 1 MOSFET, P-Ch, 12V, 4.3A, SOT-23 International Rectifier IRLML6401TRPBF R1, R2, R3, R4, R5, R6, R7, R8 8 75 ohm Resistor 1%, 1/16W, 0402 ROHM MCR01MZPF75R0 R11 1 750 ohm Resistor 1%, 1/16W, 0402 Vishay CRCW0402750RFKED R12, R13, R14, R15, R32, R33, R34, R35, R36, R37 10 10k ohm Resistor 5%, 0.1W, 0603 ROHM MCR03EZPJ103 R16, R18, R20, R22, R24, R40, R42, R44, R46, R48 10 300 ohm Resistor 5%, 0.1W, 0603 ROHM MCR03EZPJ301 R17, R19, R21, R23, R25, R39, R41, R43, R45, R47, R49 11 270 ohm Resistor 5%, 0.1W, 0603 ROHM MCR03EZPJ271 R26, R27 2 22 ohm Resistor 5%, 1/10W, 0603 ROHM MCR03EZPJ220 R28 1 100 ohm Resistor 1%, 1/16W, 0402 ROHM MCR01MZPF1000 R29, R31 2 16.5k ohm Resistor 1% 0.1W, 0603 ROHM MCR03EZPFX1652 R30 1 36.5k ohm Resistor SMD 1%, 0.1W, 0603 ROHM MCR03EZPFX3652 R38 1 300 ohm Resistor SMD 1%, 1/16W, 0402 ROHM MCR01MZPF3000 R50 1 52.3k ohm Resistor SMD 1%, 0.1W, 0603 ROHM MCR03EZPFX5232 R51 1 2.74k ohm Resistor 0603 1%, 0.1W, 0603 ROHM MCR03EZPFX2741 R52 1 100k ohm Resistor 5%, 1/10W, 0603 ROHM MCR03EZPJ104 S1, S2, S3, S4, S5, S6 6 Switch, Tactile, SPST w/GND, SMD Omron Electronics Inc B3U-1100P U1 1 AVR 8-bit Microcontroller, 128K, 64QFN Atmel AT90USB1287-16MU U2 1 Regulator, LDO, 300mA, 3.3V, 8MSOP National Semiconductor LP3981IMM-3.3/NOPB U3 1 LMH0307 3G SDI Dual Cable Driver, LLP16 National Semiconductor LMH0307SQ X1 1 Crystal, 8.00 MHz , 8 pF, Fund, SMD NDK NX5032GA 8MHZ AT-W SD303/SD307 EVK User Guide 19 of 27 Rev 1.2 © 2010, National Semiconductor Corp.

ORL (Output Return Loss) plots are shown for each output. Eye patterns showing transition times and jitter are shown for 2.97 Gbps. Amplitude measurements are shown for the outputs at 270 Mbps. Equipment: HP 8722ES Network Analyzer, Agilent DCA-J 86100C Scope, BertScope Digital Synthesis Conditions: Nominal supply and room temperature, connection cables only ORL Plot - Channel 0 – Negative SD303/SD307 EVK User Guide 20 of 27 Rev 1.2 © 2010, National Semiconductor Corp.

ORL Plot - Channel 1 – Positive SD303/SD307 EVK User Guide 21 of 27 Rev 1.2 © 2010, National Semiconductor Corp.

Smith Chart – Channel 0 – Positive SD303/SD307 EVK User Guide 22 of 27 Rev 1.2 © 2010, National Semiconductor Corp.

2.97Gbps EYE - Channel 0 – Positive – Jitter SD303/SD307 EVK User Guide 23 of 27 Rev 1.2 © 2010, National Semiconductor Corp.

270 Mbps EYE – Channel 0 – Positive – Color Bar – Amplitude SD303/SD307 EVK User Guide 24 of 27 Rev 1.2 © 2010, National Semiconductor Corp.

270 Mbps EYE – Channel 1 – Positive – Color Bar – Amplitude Schematic SD303/SD307 EVK User Guide 25 of 27 Rev 1.2 © 2010, National Semiconductor Corp.

Drawn By: GND RSTIbar SDA SCL ENABLE SD/HDbar FAULT RSTObar RCDLED GCDLED RTF0PLED GTF1NLED RTF1NLED GTF1PLED RTF1PLED GTF0NLED RTF0NLED GTF0PLED VCC DVCC LMH0303USBDigital LMH0303USB SDI 1 SDIbar 2 VEE 3 RREF 4 RSTIbar 5 ENABLE 6 SDA 7 SCL 8 VCC 9 SD/HDbar 10 SDO0bar 11 SDO0 12 FAULT 13 SDO1 14 SDO1bar 15 RSTObar 16 DAP 17 U3 LMH0303 / LMH0307 J1 J2 GND J3 GND J4 GND J6 GND J5 VCC VCC GND VCC VCC GND GND GND GND GND GND GA 1 RA 2 GK 3 RK 4 D10 BiColored LED GA 1 RA 2 GK 3 RK 4 D9 BiColored LED GA 1 RA 2 GK 3 RK 4 D11 BiColored LED GA 1 RA 2 GK 3 RK 4 D7 BiColored LED GA 1 RA 2 GK 3 RK 4 D8 BiColored LED DVCC DVCC DVCC DVCC DVCC VCC GND VCC VCC GND VCC VCC VCC VCC GND GND GND GND RSTObar FAULT RSTObar FAULT SCL SDA RSTIbar ENABLE SDO0bar SDO0 SDO1bar SDO1 SDI SDIbar GCDLED RCDLED RTF0NLED GTF0NLED GTF0PLED RTF0PLED GTF1PLED RTF1PLED GTF1NLED RTF1NLED VCC GND GTF1NLED RTF1NLED GTF1PLED RTF1PLED GTF0NLED RTF0NLED GTF0PLED RTF0PLED GCDLED RCDLED SD/HDbar DVCC GND GND GND R10 OPEN R9 OPEN R5 75 R6 75 R7 75 R8 75 R3 75 R1 75 R2 75 R4 75 R28 100 R11 750 R12 10K R16 300 R17 270 C1 1uF C2 1uF C3 4.7uF C4 4.7uF C5 4.7uF C6 4.7uF C7 100pF C8 0.1uF C9 10uF 1 J8 BANANA JACK (Red) 1 J9 BANANA JACK (Black) 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 JP1 Header 10X2 L4 6.8nH L3 6.8nH L1 6.8nH L2 6.8nH R13 10K R14 10K R15 10K R18 300 R24 300 R19 270 R25 270 R20 300 R22 300 R21 270 R23 270 C30 0.1uF C31 0.1uF GND SD303 / SD307 Evaluation Board for the LMH0303 / LMH0307

Drawn By: GND PE6 1 PE7 2 UVCC 3 Dm 4 Dp 5 UGnd 6 UCap 7 VBUS 8 PE3 9 PB0 10 MCK_PB1 11 MOSI_PB2 12 MISO_PB3 13 PB4 14 PB5 15 PB6 16 PB7 17 INT4_PE4 18 INT5_PE5 19 RESETz 20 VCC 21 GND 22 XTAL2 23 XTAL1 24 SCL_PD0 25 SDA_PD1 26 INT2_PD2 27 INT3_PD3 28 PD4 29 PD5 30 PD6 31 PD7 32 PE0 33 PE1 34 PC0 35 PC1 36 PC2 37 PC3 38 PC4 39 PC5 40 PC6 41 PC7 42 HWBz 43 PA7 44 PA6 45 PA5 46 PA4 47 PA3 48 PA2 49 PA1 50 PA0 51 VCC 52 GND 53 PF7 54 PF6 55 PF5 56 PF4 57 PF3 58 PF2 59 PF1 60 PF0 61 AREF 62 GND 63 AVCC 64 DAP 65 U1 AT90USB1287 VBUS 1 Dm 2 Dp 3 ID 4 GND 5 SHLD 6 J7 MINI_USB_B Vout 1 Vin 2 NC1 3 Sense 4 GND 5 Bypass 6 Ven 7 NC2 8 U2 LP3981 Q1 IRLML6401PbF VCC DVCC GND GND GND X1 8MHz SD/HDbar SDA SCL RSTObar RSTIbar ENABLE FAULT RCDLED GCDLED RTF0PLED GTF0PLED GTF0NLED RTF0NLED GTF1PLED RTF1PLED GTF1NLED RTF1NLED 1 1 GND 3 2 2 S1 TACTSW GND DVCC GND DVCC GND GND DVCC DVCC GND GND GND GND GND GND DVCC DVCC GND GND GND GND GND GND GND D 6 GND 5 C 4 A 1 GND 2 B 3 D13 CEBS0624V-G GND GND SAVE RESETbar ENABLE_SW SD/HDbar_SW MODE_SW RSTI_SW DVCC DVCC DVCC DVCC DVCC DVCC GND GND GND GND GND GND USB Power Enable SD/HDbar MODE RSTObar RSTIbar A1 1 A2 2 K2 3 A3 4 A4 5 K1 6 D14 BAS40DW05 7 5 9 11 8 10 12 3 1 2 4 6 14 13 JP2 HEADER 7X2 GND DVCC GND GND 1 FD0 1 FD1 1 FD2 R38 300 R26 22 R29 16.5K 1% R31 16.5K 1% R30 36.5K 1% R50 52.3K 1% R51 2.74K 1% R52 100K 5% C10 4.7uF C11 4.7uF C14 4.7uF C24 4.7uF C26 4.7uF C28 4.7uF C25 100pF C27 100pF C29 100pF C16 18pF C17 18pF C13 1uF C15 1uF C20 1uF C21 1uF C22 1uF C23 1uF C12 0.033uF C19 220nF C18 220nF GA 1 RA 2 GK 3 RK 4 D1 BiColored LED GA 1 RA 2 GK 3 RK 4 D2 BiColored LED GA 1 RA 2 GK 3 RK 4 D3 BiColored LED GA 1 RA 2 GK 3 RK 4 D4 BiColored LED GA 1 RA 2 GK 3 RK 4 D5 BiColored LED GA 1 RA 2 GK 3 RK 4 D6 BiColored LED 1 1 GND 3 2 2 S2 TACTSW 1 1 GND 3 2 2 S3 TACTSW 1 1 GND 3 2 2 S4 TACTSW 1 1 GND 3 2 2 S5 TACTSW 1 1 GND 3 2 2 S6 TACTSW R32 10K R33 10K R34 10K R35 10K R36 10K R37 10K R40 300 R42 300 R44 300 R46 300 R48 300 R39 270 R41 270 R43 270 R45 270 R47 270 R49 270 R27 22 DVCC SD303 / SD307 Evaluation Board for the LMH0303 / LMH0307

Texas Instruments: SD303EVK/NOPB SD307EVK/NOPB