Magnadyne DVU-3G2 Installation Instructions

Model: DVU-3G2 Installation Instructions DVU-3G2-INS Rev. B 3-5-13 © 2013 Copyright Magnadyne Corporation Mounting the Unit Screw Mount: The DVU-3G2 comes with screws to permanently mount the unit to the dashboard or some other area in the vehicle. 1. Make sure that the mounting location does not interfere with the operation of the vehicle. Also make sure the screws will not damage anything behind the dash. 2. Use the provided screws to mount unit. Velcro Mount: The DVU-3G2 comes with a Velcro pad for mounting the unit to the dashboard or some other accessible area in the vehicle. 1. Make sure the surface area where the Velcro will adhere to is clean. The area must be free from any interior protectorants. 2. Remove the backing on one side of the Velcro pad and apply the to the DVU-3G2. 3. Remove the backing on the other side of the Velcro pad and press the unit firmly into the designated mounting location. Hard Wiring: The DVU-3G2’s can be hard wired for permanent installation in a vehicle. 1. Cut off the VPA connector making sure to leave the enough cable to reach the connection point. 2. Connect the wire with the white stripe to a fused 15A switched power source. Note: If the wire with the white stripe is not connected to a switched power source when the ignition is turned off the DVU-3G2 will continue to draw its power from the vehicle’s battery and over an extended time may drain the battery. 3. Connect the black wire to chassis ground. Optional Hard Wiring Warnings • FCC REGULATIONS STATE THAT ANY UNAUTHORIZED CHANGES OR MODIFICATIONS TO THIS EQUIPMENT MAY VOID THE USER’S AUTHORITY TO OPERATE IT. • TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT INSTALL THE UNIT IN A PLACE EXPOSED TO DIRECT SUNLIGHT OR EXCESSIVE HEAT OR HUMIDITY. AVOID PLACES WITH TOO MUCH DUST OR THE POSSIBILITY OF WATER SPLASHING OR GETTING WET. • THIS DEVICE IS INTENDED FOR CONTINUOUS OPERATION. • TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK AND ANNOYING INTERFERENCE, USE ONLY THE RECOMMENDED ACCESSORIES. • IN CERTAIN VEHICLES THE ADAPTER WILL DRAW POWER EVEN WHEN VEHICLE IS TURNED OFF AND DEPENDING ON USAGE MAY DRAIN THE VEHICLE’S BATTERY. • Never install the product in a location where it interferes with your field of vision. • Use the proper power supply. This product is designed for operation with a neg- ative grounded 12V DC battery system. If the product is used with the improper system it may cause a fire or an accident. • This product must be installed and used in accordance with this manual. Any alter- ations to this product that enables it to be used in any way other than intended or designed could distract the driver and result in an accident causing injury or death. Magnadyne Corporation disclaims any and all liability that may result from failure to install and operate in any other manner in which this unit was intended. • Do not disassemble, modify the unit or attempt to repair the product yourself. If the product needs to be repaired, consult your dealer. Caution Conect the Wire with the White Stripe to a Fused 15A Switched Power Source Conect the Black Wire to Chassis Ground

Model: DVU-3G2 Note: Power consumption for all connected devices shall not exceed 120 watts. Operation Instructions Changing the Fuse: Should the DVU-3G2 fail to operate, replace the fuse. 1. Unplug the DVU-3G2’s VPA plug from the vehicle’s power socket. 2. Use a fuse puller to remove the fuse. 3. If the fuse is burnt, place a new fuse with exactly the same amperage rating (15 Amp). 4. Plug the VPA plug back into the vehicle’s power socket. 5. If the DVU-3G2 works correctly after fuse replacement con- tinue to use the device. Note: If the DVU-3G2 does not function properly and the new fuse blows immediately, there is a problem and discontinue use. Trouble Shooting USB Operation Instructions Inserting a USB Cable: Gently insert the USB drive into the slot. Note: If a USB connector does not insert, DO NOT FORCE it into the slot, flip the connector over and try again. Inserting a VPA Charger: 1. Remove the cover from a VPA socket. The interior of the socket will be illuminated green indicating the unit has power. 2. Insert the VPA into the socket. Make sure to fully insert the charger. 3. To remove the charger hold the DVU-3G2 and pull the VPA charger out of the socket. Do not pull the VPA’s cable to remove the charger. Removing a USB Cable: Pull the USB connector straight out of the socket. Do not pull the USB’s cable to remove the USB connector from its socket. Damage may occur. VPA Operation Instructions DO NOT USE CIGARETTE LIGHTERS WITH THIS UNIT. 15 15A 15