CLS LDC-41 Operation & User’s Manual

Wall 170 gr IP20 Max. 0,5 Watt 24~48 VDC # 58014 CLS LDC-41 GII DMX LED DRIVER Manual V1.0 - December 2017 Index 2 Safety information 3 Optional accessories 3 Introduction 4 Measurements 4 Lay-out description 4 Pinning DMX output 4 Installation 5 Mounting 5 Choosing power supply 5 Connect power supply 6 Connect LED fixture 6 Connect DMX 7 Status display 8 Configuration 8 Page 1: DMX addressing 9 Page 2: Channel configuration 9 Page 3: Control configuration 10 Page 4-7: Current configuration 10 Page 8: Test sequence 10 Page 9: Store configuration 10 Page 10: Cancel configuration 10 Technical specifications 11 INDEX

- 4 - Optional accessories 911465 CLS LD serie GII adapter cable XLR3 male to RJ45 911468 CLS LD serie GII adapter cable RJ45 to XLR3 female 911366 CLS LDC adaptercable LDC to XLR7 including terminator 911367 CLS LDC adaptercable LDC to SmartConnect system 911368 CLS LD serie adapter cable RJ45 to XLR3 female 113100 CLS LDC-41 connection cable to XLR7 including terminator 113110 CLS LDC-41 connection cable to Luxo 3 RGB 707028 CLS Zense DMX controller + built in 4 amp RGB dimmer 707030 CLS ACX60 DMX controller for max. 60 channels 706995 CLS BT20.24 LED power supply 24VDC 2-VA 85-264VAC 707011 CLS BT45.24 LED power supply 24VDC 45VA 85-264VAC 707012 CLS BT75.24 LED power supply 24VDC 75VA 85-264VAC 707013 CLS BT120.24 LED power supply 24VDC 120VA 85-264VAC 707014 CLS BT240.24 LED power supply 24VDC 240VA 85-264VAC 707018 CLS BT75.48 LED power supply 48VDC 75VA 85-264VAC 707019 CLS BT120.48 LED power supply 48VDC 120VA 85-264VAC 707020 CLS BT240.48 LED power supply 48VDC 240VA 85-264VAC Ambiance Max. 40º Block access below the work area when maintaining the unit Use a source of AC power that complies to local electrical codes Disconnect the power supply before installing or maintaining Don’t install in a flammable or explosive area Warning! Some surfaces can be hot Do not stare into the LED Don’t modify or install genuine parts on this product Qualified technician Make sure all connectors are connected properly Wall 170 gr IP20 Max. 0,5 Watt 24~48 VDC CONTENT SAFETY INFORMATION MEASUREMENTS The CLS LDC-41 is a DMX controllable LED dimmer, which has 4 current controlled DC outputs. The current can be adjusted in steps of 50mA from 350 to 1000mA per channel. Each channel can drive 2 to 12 LEDs in series. Equipped with 4 channels the LDC-41 is suitable for controlling the newest generation of LED fixtures, RGBW or RGBA. This makes it possible to connect 2 to 12 RGB or even RGB(A/W) fixtures on one driver. Unique is the DIN-rail mounting possibility of the new and small housing. The LDC-41 is equipped with a user friendly menu structure, which offers some smart solutions for installers to test and set up an installation. 25 mm 125 mm 110 mm 15 mm 15 mm 110 mm Output connector Power input connector Display Up button DMX input/output DMX input/output Menu button Down button LAY-OUT DESCRIPTION PINNING DMX OUTPUT � � � � � � � � � � � � � � � � 1 .G ND 2.D- 3.D+ 1 .G ND 2.D- 3.D+ DMX OUT DMX IN DMX OUT DMX IN XLR3 XLR5 4. N/C 5. N/C INTRODUCTION PIN COLOUR FUNCTION 1 Orange/white DMX data + 2 Orange DMX data - 3 Green/White Not connected 4 Blue Not connected 5 Blue/White Not connected 6 Green Not connected 7 Brown/White DMX Common 8 Brown DMX Common

- 6 - This section describes in general terms how to install the LDC-41. How to setup the menu, data link and how to connect it to a fixture. Mounting The LDC-41 has a unique feature, it is designed to be installed on a DIN-rail. Now it is possible to install the LDC-41 directly next to the power supplies which are also suitable for DIN-rail mounting. This helps to keep your installation work modular and fault proof. Choosing power supply Use a power supply with an output voltage which is compatible with the LED fixtures you are using. To choose the correct power supply use the two tables below. Keep in mind that the table is determined with an equal load on all 4 outputs. For example 6 LEDs means 6 LEDs on all 4 outputs. * The number of fixtures is divided in 3 catagories, total = total amount of fixtures on the driver, minimum = miminum amount of fixtures per channel, maximum = maximum amount of fixtures per channel. With RGB (A/W) fixtures total is not used because per fixture all channels are used. INSTALLATION Locate the “INPUT” connection block at the top of the LDC-41, check information sticker on the side of the LDC-41. Connect the positive (+) output of the power supply to positive (+) power input of the LDC-41. Connect the negative (-) output of the power supply to the negative (-) power input of the LDC-41. Connect LED fixture Locate the “OUTPUT” connection block at the top of the LDC-41, check information sticker on the side of the LDC-41. Connect the fixture’s RED positive (+ or anode) to Channel 1 (R) of the LDC-41. Repeat this step for the Green, Blue and/or White/Amber colour. If all colours have separate negative (- or cathode) wires then tie them together and connect to negative (-) power input of the LDC-41. If all colours have a combined negative (- or cathode) wire, connect to negative (-) power input of the LDC-41. The LDC-41 can also control single colour LED fixture’s. You can use the 4 output to create different zone’s that can be controlled separately or simultaneously. ATTENTION! Make sure that none of the products you are working on, are powered! WARNING 24-48 VDC Amber / White Blue Green Red CONNECT POWER SUPPLY

- 8 - Status display The LDC-41 has a display which is used to interface with the user. When the LDC-41 is powered the DMX address is showed. When DMX is active the DMX status dot is on. By pressing the menu button you can scroll through the different status pages. The status pages dots will indicate which page is displayed. The status pages will show the output value of the outputs 1-4 from 0 (min) to 255 (max). DMX status Page 4: output status Chn. 4 Page 1: output status Chn. 1 Page 2: output status Chn. 2 Page 3: output status Chn. 3 Page 1: Adr Status display Page 2: Chn Page 3: Con Page 4: Cu1 Page 5: Cu2 Page 6: Cu3 Page 7: Cu4 Page 8: tSt Page 9: Sto Page 10: Cnl Hold Menu button for 3 seconds to enter menu Hold Menu button for 3 seconds to store or cancel Use Up/Down button Menu description When the LDC-41 is powered the status display is shown with the DMX address. To enter the menu press and hold the menu button for 3 seconds. The LDC-41 will enter menu interface on page 1. The menu interface holds different pages. Use the up and down button to scroll through the pages. To select the page press the menu button. In each page the settings can be adjusted. To leave a page press the menu button again. CONFIGURATION The LDC-41 must be configured to fit the application it is used for. To make configuration easy the LDC-41 has a user friendly menu interface. Connect to DMX The LDC-41 has two connections for DMX. Both DMX connections are input/output. When using the LDC-41 is combination with the CLS Zense DMX controller, you can simply connect the two devices with a standard RJ45 (UTP) cable. There is no need for a external power supply for the Zense, the LDC-41 supplies the Zense with power through the RJ45 connection. When using the LDC-41 with a DMX controller, other than the CLS Zense you can find the connection method on the side of the LDC-41. When no UTP cable is used it is adviced to use the LD-serie gender changer cable (art. 911465). Input Output DIN rail Max. 30 CLS LDC-41 in one chain CLS Zense DMX controller + built in 4 amp RGB dimmer # 707028 CLS BT power supply CLS BT power supply 24 VDC CLS LD serie adapter cable RJ45 to XLR3 female # 911368 CLS LD serie GII adapter cable XLR3 male to RJ45 # 911465

- 10 - Page 1: DMX addressing In this page you can adjust the DMX address of the LDC-41. Use the up and down button to adjust the value. Hold down the up or down button to scroll fast. When DMX address is selected press the menu button to return to the main menu. Default DMX address: 1 1 - 507 Page 1: Adr Use Up/Down button Press the Menu button to return Page 2: Channel configuration In this page you can adjust the Channel configuration of the LDC-41. With the channel configuration you can configure how the outputs respond to the DMX channels. Use the up and down button to adjust the value. When Channel configuration is selected press the menu button to return to the main menu. DMX channel n is the DMX address of the LDC- 41. Option 1: All 4 outputs respond to DMX channel n. This option can be used for single colour applications. Option 2: The first 2 channels respond to DMX channel n and last 2 channels respond to DMX channel n+1. This can be used for 2 zones single colour applications. Option 3: The first 3 channels respond to separate DMX channels n and last 2 channels respond to DMX channel n+1. This can be used for 3 zones single colour applications. Option 4: All 4 outputs respond to separate DMX channels. This option can be used for RGB(A/W) applications. Default Channel option: 4 1 - 4 Page 2: Chn Use Up/Down button Press the Menu button to return Output DMX channels n n+1 n+2 n+3 1 √ - - - 2 √ - - - 3 √ - - - 4 √ - - - Output DMX channels n n+1 n+2 n+3 1 √ - - - 2 √ - - - 3 - √ - - 4 - √ - - Output DMX channels n n+1 n+2 n+3 1 √ - - - 2 - √ - - 3 - - √ - 4 - - √ - Output DMX channels n n+1 n+2 n+3 1 √ - - - 2 - √ - - 3 - - √ - 4 - - - √ Page 3: Control configuration In this page you can adjust the Control of the LDC-41. By enabling the Control configuration the LDC-41 will use a master dimmer channel. With the master dimmer channel the light can be dimmed without changing the colour channels. The master dimmer channel will be added after the last DMX channel used to control the outputs of the LDC-41. Use the up and down button to adjust the value. When Channel configuration is selected press the menu button to return to the main menu. Default Control configuration: Disabled (0) 0 - 1 Page 3: Con Use Up/Down button Press the Menu button to return Channel Option Control configuration Disabled (0) Enabled (1) 1 - DMX channel n+1 2 - DMX channel n+2 3 - DMX channel n+4 Page 4-7: Current configuration To adjust the current of an output channel enter the corresponding page and change the value. The current can be adjusted from 350 – 1000mA in steps of 50mA. To return to the main menu press the menu button. 0.35 - 1.00 Page x: Cux Use Up/Down button Press the Menu button to return Page 8: Test sequence Entering this page will result in a test sequence on the outputs of the LDC-41. This enables the user to test the connections without the need of an DMX controller. To end the test sequence and return to the main menu press the menu button. Test sequence Page 8: tSt Press the Menu button to enter or return Page 9: Store configuration After all changes are made the setting need to be stored before they become active. To store the settings go to the store page and press and hold the menu button for 3 seconds. The settings are stored and you will return to the status display. Status display Page 9: Sto Hold the Menu button for 3 seconds to store Page 10: Cancel configuration When you have made changes but you don’t want to store them you can leave the configuration menu without storing them. To cancel the settings go to the cancel page and press and hold the menu button for 3 seconds. The settings are not stored and you will return to the status display. Default Current configuration: 700mA for each channel Status display Page 10: Cnl Hold the Menu button for 3 seconds to cancel

- 12 - Spefifications Power Supply: 24-48VDC Idle Power: Max. 0,5 Watt Power consumption: Max. 185 Watt LEDs in serie: 2-12 per channel Output: 4 channels Output voltage: 22-46VDC Output current: 350-1000 mA Fuse: no fuse DMX protocol: DMX512/1990 Data in/out: RJ45 Housing: Plastic IP rating: IP40 Measurements: 110 x 25 x 125 mm (hxwxd) Mounting: DIN-rail Weight: 210 gr Working temperature: -10 °C to +60 °C TECHNICAL 2018 CLS-LED BV. All rights reserved. Information subject to change without notice, CLS-LED BV and all affiliated companies disclaim liability for injury, damage direct or indirect loss, consequential or economic loss or any other loss occasioned by the use of, inability to use or reliance on the information contained in this manual. No part of this manual may be reproduced, in any form or by any means, without permission in writing from CLS-LED BV. Other legal information can be found in our General conditions, found on the back of your CLS-LED BV invoice, inside the CLS catalogue or on our website www.cls-led.com/General-Terms.pdf LIST OF SYMBOLS Multiple connection Daisychain connectivity Installation depth In centimeters Swivel Fixture is horizontally rotatable, indicated in degrees Swivel Fixture is vertically rotatable, indicated in degrees Installation size In centimeters Application area Indoor or outdoor Application area Floor, wall or ceiling Protection class One, two or three Cable length Maximum cable attached to the fixture in centimeters Lifespan Of the light source in hours Driver Inclusive or exclusive Internal or external Pressure Maximum pressure on the fixture in kg/cm2 Weight In grams/kilograms Curve Minimal bending curve in centimeters LED pitch Pitch between the LEDs in millimeters Power supply In VDC, VAC or milliAmpere Power consumption In VA or Watt IP value Ingress Protection classifies the degrees of protection provided against the intrusion of the product Cutting length Indicated by the cutting marks LEDs Kind of LED used in the fixture Lenses Availble lenses, indicated in degrees Plug & play Easy connection using the SmartConnect system White colour temperature In diferent Kelvin values; Cold white, neutral white, warm white or extra warm white Colour Available colours; Amber, blue, red or green Colour changing RGB, RGB-W, RGB-A, AWB or Tunable White DMX input Fixture works on DMX512 protocol Magno dimming Accurate dimming from 100 - 1% by using a magnet Dynamic Control Dynamic Power Control or Dynamic Temperature Control Combined product Compose your own fixture Warranty 3 or 5 years warranty on the product Energy label Conformité Européenne CE marking for free marketability of industrial goods within the EU r h ø w d Dimmable 1-10 Volt, Phase, individual, DMX dimmable or DALI DRIVER INCLUDED DRIVER EXTERNAL Retail & Food LED modules Clothing, furniture, kitchens, jewellery, shoes, bread, meat, fish & vegetables & fruit. Lightsource Equipped with a CLS, Citizen or a Xicato LED module Bluetooth controlled By Casambi CLS DYNAMIC COLOUR COB