ICPDAS USB-87P2 Quick Start Manual

ICP DAS, Co., LTD www.icpdas.com  Package Checklist Items Quantity Model No. Description USB-87Pn 1 USB-87P1 Hardware module: USB-87Pn I/O Unit P1: 1 Slot P2: 2 Slots P4: 4 Slots P8: 8 Slots USB-87P2 USB-87P4 USB-87P8 Cable 1 CA-USB18 USB connector cable Manual 1 - Quick Start Manual (this manual) CD 1 - Software utility, USB-87Pn User Manual Screw Driver 1 - 2.4 mm Screw driver (minus style) NOTE: USB-87Pn is only for High Profile I-87K I/O modules, please DO NOT use Low Profile I/O modules. For more information, please refer to Chapter 2.2.5 & Appendix B of “USB-87P1/2/4/8 User Manual”.  Preparation  Power Supply: +10V ~ +30V /DC (Ex: DP-665) http://www.icpdas.com/products/Accessories/power_supply/power_list.htm  Install USB-87Pn DriverInstaller to PC: at CD:\NAPDOS\87pn_io_unit\USB-87Pn or ftp://ftp.icpdas.com/pub/cd/8000cd/napdos/87pn_io_unit/USB-87Pn/  Install DCON Utility to PC: (Version 4.5.2 or above version. Please remove the old version before install the new version) at CD:\ Napdos\Driver\DCON_Utility or ftp://ftp.icpdas.com/pub/cd/8000cd/napdos/driver/dcon_utility/ Original Writer : Eva Li Last Editor : Hans , 05/27/2015

1. View of the USB-87Pn Slot 0 Power Module CPU Module High Profile I-87K I/O Slots 87Pn Power Power Connector Slots LED indicators indicators CPU Power System Ready Auto Configuration Indicator Auto Configuring Dip Switch Enable/Disable Slot 1 Slot 2 Slot 3 USB Port Power & CPU Module High Profile I-87K I/O Slots Power Connector Auto Configuring Dip Switch Enable/Disable USB Port Slots LED Indicators Power System Ready Auto Configuration Indicator Slot 0 Slot 1 USB-87P4 USB-87P8 is like USB-87P4, but with 8 slots. USB-87P2 USB-87P1 is like USB-87P2, but with 1 slot.

3. Configure CPU Module Switch Label Setting Description Dip Switch Auto Config. ON Enable (Switch to ON) OFF Disable USB Connector Cable (CA-USB18) PC (COM X) USB-87P4 Power Supply +10~+30 VDC GND +Vs +Vs GND To USB port To USB port

Example: Plug in I-87019R to Slot 0. p.s. I-87019R is an AI (Analog Input) High Profile module I-87019R is auto-configured: Baud Rate: 115200 Checksum: Disable Net Address: 2 Note: The Net Address of USB-87PN is always 1.  After plugged in, the slot indicator is flashing per 100 ms.  When software configuration is completed, the LED becomes off.  If configuration is failed, the LED is always on. High Profile 66.7 87.46 102.14 81.08 Low Profile Slot: 0 1 2 3          Net Address: 1 2 3 4 5

1. Run DCON Utility to Search the USB-87Pn (Ex: USB-87P8) Note: Please finish the “Preparation” (See P.1) before Software Configuration. The old version of USB-87Pn with old USB chip, it needs to install old USB driver, and Device Manager will show as below: 1 2 Check “Device Manager” of your PC to see the connecting COM.

3. Configure the 87K I/O Module 1 2 3 4 If the status code is not [01H], click button and follow the instruction please. 4 3 2 3 1

5. Click “Start Search” Button Note: For changing the configuration of 87K I/O module, please repeat from the STEP 2 of the Software Configuration. “[0,0,0,0...]” of “Status” means “The I/O configuration of each slot is correct”. Each plugged I/O module will be listed under the USB-87Pn. User can click the name of I/O module to watch its configuration. After “Write To 87Pn”, the Status Code is changed to “[00H] OK” that means “The configuration is correct”. 1 2

Doesn’t need to configure I/O module again! Easy! Convenient!  Technical Support 1. USB-87P1/2/4/8 User Manual CD:\NAPDOS\87Pn_io_unit\USB-87Pn or ftp://ftp.icpdas.com/pub/cd/8000cd/napdos/87pn_io_unit/usb-87pn/ 2. DCON Utility User Manual CD:\ Napdos\Driver\DCON_Utility\Manual or ftp://ftp.icpdas.com/pub/cd/8000cd/napdos/driver/dcon_utility/manual/ 3. I-87K high profile series I/O modules selection guide http://www.icpdas.com/products/PAC/i-8000/8000_IO_modules.htm 4. Our service email account : [email protected] 5. Our website : www.icpdas.com Remove the damaged module. Plug in a new one with the same model number.