Clear-Com RM-702-IM Operation & User’s Manual

Important Safety Instructions 1. Read these instructions. 2. Keep these instructions. 3. Heed all warnings. 4. Follow all instructions. 5. Do not use this apparatus near water. 6. Clean only with dry cloth. 7. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions. 8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat. 9. Only use attachments/accessories specified by the manufacturer. 10. Use only with the cart, stand, tripod, bracke ...

Engineers, or in the case of project installations, once the Project Team has completed the hand-over to the Support Centers. 6.3 Return Material Authorization Policy a. Authorizations: All products returned to Clear-Com or a Clear-Com Authorized Service Partner must be identified by a Return Material Authorization (RMA) number. b. The Customer will be provided with an RMA number upon contacting Clear-Com Sales Support as instructed below. c. The RMA number must be obtained from Clear-Com via phone or email prior to returning product to the Service Center. Product ...

3.7.3 Internal IFB Operation To use either channel A or B as an IFB feed, connect the program source to the program input (as described in the previous section) and set the Program Interrupt A (or B) DIP switch to the on position. The program will now be interrupted whenever there is a call signal present on channel B. If there are multiple RM-702s in the system, the program should only be fed into one of the RM-702s. To interrupt the IFB program automatically when a talk rather than a call signal is active on channels A or B, you must reset an internal jumper as d ...

Europe, the Middle East and Africa: Hours:0800 - 1700 GMT + 1 Days:Monday - Friday Tel:+ 44 1223 815000 Email:[email protected] iv. Note: AWRs are not available for UHF WBS Analog wireless intercom systems. UHF WBS Analog wireless intercom systems out-of-box failures must be returned to Clear-Com for repair. v. Note: Out-of-box failures returned after 90 days will be repaired and not replaced unless approved by Clear-Com Management. vi. Note: AWRs are not available after 90 days of receipt of product unless an AWR Warranty Extension is purchased at the ...

Table of contents 1 Compliance 6 2 Operation 9 2.1 Introduction 9 2.2 The Clear-Com Concept 9 2.3 Description 10 2.4 Operation 11 3 Installation 14 3.1 Installation Overview 14 3.2 Description of Front panel Connectors 17 3.3 Headset Connector (Front Panel) 17 3.4 Description of Rear Panel Connectors 18 3.5 Description of Options and Adjustments 19 3.6 Typical System Applications 24 3.7 Actual Applications 26 4 Maintenance 34 4.1 Introduction 34 5 Technical Specifications 35 5.1 RM-702/RM-802-IM Two-Channel Station 35 6 Technical Support and Repair Policy 39 6.1 Te ...

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 “ACCESSORY” CONNECTOR DB-15F Power (+30 VDC) GND – Program Input + Program Input Viewed from the rear of the unit 1. Connect a balanced input to pins #8 and #15 with the shield connected to pin #7. 2. To connect an unbalanced input, connect the signal to pin #8 and connect the shield to pins #15 and #7. l Connecting Party-Line Products As Program Sources: If other Clear- Com products (such as an AC-701 telephone interface) are to be used as a program source directly, use the following interconnection cable. Pin #14 ...

3 Installation This section discusses the installation of the RM-702/RM-802-IM in an intercom system including typical applications, overall installation theory, detail of each connector, and adjustments. 3.1 Installation Overview This section describes the Clear-Com concept of intercom line connection. The following subjects are discussed: l Intercom line connection l Line termination l Station powering l Cable considerations 3.1.1 Intercom Line Connection The RM-702/RM-802-IM provides male and female XLR-3 connectors for each intercom line, which are looped throu ...

Document reference RM-702/RM-802-IM User Guide 399G260 Rev A Legal disclaimers Copyright © 2018 HME Clear-Com LtdHME Clear-Com Ltd All rights reserved Clear-Com, the Clear-Com logo, and Clear-Com Concert are trademarks or registered trademarks of HM Electronics, Inc. The software described in this document is furnished under a license agreement and may be used only in accordance with the terms of the agreement. The product described in this document is distributed under licenses restricting its use, copying, distribution, and decompilation / reverse engineering. N ...