Cisco SCE8000 Configuration Manual

2-1 Cisco SCE8000 10GBE Installation and Configuration Guide OL-16478-05 2 Introduction to the Cisco SCE8000 10GBE Platform Revised: August 23, 2010, OL-16478-05 Introduction This chapter provides an introduction to the Cisco SCE8000 10GBE platform, the Service Control hardware component. • Information About the SCE Platform, page 2-1 • Service Control Module (SCE8000-SCM-E), page 2-3 • Introduction to SIPs and SPAs, page 2-5 • The SCE8000-SIP, page 2-8 • The 1-Port 10GBE SPA Interface Module, page 2-8 • The Cisco SCE8000 Optical Bypass, page 2-9 • Checking the Shipping Container Contents, page 2-15 • Cisco SCE8000 Installation Checklist, page 2-17 Information About the SCE Platform The Service Control Engine (SCE) platform, which is the hardware component of the Cisco Service Control solution, is designed to support observation, analysis, and control of Internet/IP traffic. Table 2-1 summarizes model information for the Cisco SCE8000 platform. Table 2-1 SCE Platform Model Information Model number Cisco SCE8000 10GBE Link Type 10 Gigabit Ethernet Number of Ports 2 or 4 Number of Links 1 or 2

OL-16478-05 Chapter 2 Introduction to the Cisco SCE8000 10GBE Platform Information About the SCE Platform The Cisco SCE8000 10GBE is a transparent element with 10GBE links service throughput (Figure 2-1). It can be installed inline in the network where the entire traffic passes through it or in receive-only mode where it receives replication of the traffic through SPAN ports or optical splitters. Figure 2-1 Cisco SCE8000 Platform The Cisco SCE8000 supports the following network insertion models: • single appliance (inline) • single appliance (receive-only) • cascade configuration • MGSCP configuration The Cisco SCE8000 platform is a 4-slot chassis hosting the following modules: • One or two Service Control Modules (SCE8000-SCM-E) that each contain special purpose fast path chipset, traffic processors and control processor. • One SPA Interface Processor card (SCE8000-SIP) that holds up to four SPA 10GBE interface modules. • One optional optical bypass module hosting panel that holds up to two optical bypass modules. In addition, the Cisco SCE8000 chassis contains two power supply modules in a 1+1 configuration, as well as a fan tray module. 270543 FAN STATUS SCM 1 SCM 2 SIP 3 4 SCE8000-FAN SYSTEM POWER OPTICAL BYPASS STATUS AUX PORT 2 LINK ACTIVE MASTER SCE8000 EXTENDED SERVICE CONTROL MODULE OPTICAL BYPASS OPTICAL BYPASS CONSOLE 10 100 1000 LINK ACTIVE PORT 1 A C A B C D B D STATUS CTRL OPB-SCE8K-MM OPTICAL BYPASS1 TX RX TX RX TX RX TX RX A C A B C D B D STATUS CTRL OPB-SCE8K-MM OPTICAL BYPASS2 TX RX TX RX TX RX TX RX SYSTEM POWER OPTICAL BYPASS STATUS AUX PORT 2 10 100 1000 LINK ACTIVE MASTER SCE8000 EXTENDED SERVICE CONTROL MODULE SCE8000-SCM-E SCE8000-SCM-E SCE8000-SIP CONSOLE 10 100 1000 LINK ACTIVE PORT 1 OPTICAL BYPASS OPTICAL BYPASS STATUS ACTIVE/LINK SPA-1X10GE-L-V2 STATUS ACTIVE/LINK SPA-1X10GE-L-V2 STATUS ACTIVE/LINK SPA-1X10GE-L-V2 STATUS ACTIVE/LINK SPA-1X10GE-L-V2 10 100 1000

OL-16478-05 Chapter 2 Introduction to the Cisco SCE8000 10GBE Platform Service Control Module (SCE8000-SCM-E) Service Control Module (SCE8000-SCM-E) The Cisco SCE8000 contains one or two SCE8000-SCMs located in slots#1 and #2 (the top two slots). The Service Control module contains ports and LEDs as shown in Figure 2-2 and Table 2-2 and Table 2-3. Figure 2-2 SCE8000-SCM-E Table 2-2 SCE8000-SCM-E Ports Port Quantity Description Connect This Port To… 10/100/1000 2 (Port1 and Port2) Currently only Port1 is supported. 10/100/1000 Ethernet RJ-45 ports for management of the Cisco SCE8000. CLI designation: interface GigabitEthernet 1/1, 1/2. A LAN using a GBE cable with an RJ-45 connector. Console 1 RS-232 RJ-45 port for use by technicians A local terminal (console) using an RS-232 cable with an RJ-45 connector, as provided in the Cisco SCE8000 kit. AUX 1 RS-232 RJ-45 port used by technicians Optical Bypass 2 RJ-11 port The Control connector on the optical bypass module. SCE8000 EXTENDED SERVICE CONTROL MODULE 270874 SCE8000-SCM-E STATUS OPTICAL BYPASS MASTER SYSTEM POWER 10/100/ 1000 LINK/ ACTIVE OPTICAL BYPASS1 CONSOLE PORT1 10/100/ 1000 LINK/ ACTIVE OPTICAL BYPASS2 AUX PORT2

OL-16478-05 Chapter 2 Introduction to the Cisco SCE8000 10GBE Platform Service Control Module (SCE8000-SCM-E) Table 2-3 SCE8000-SCM-E LEDs LEDs Description System Power • Steady green — Installed power supplies are functioning normally. • Steady amber — Only one power supply is functioning normally. • Unlit — No power from either power supply. On a slave SCE8000-SMC_E module (in the second slot), this LED is always off. Status The Status LED indicates the operational status of the Cisco SCE8000 system, as follows: • Unlit — No power from either power unit. • Steady amber — The system is booting up. • Flashing amber — The system is operational, but is in a warning state. • Flashing green — The system is fully operational. • Steady red — There is a problem or failure Note Alarms are hierarchical: Failure takes precedence over Warning, which takes precedence over Operational. Optical Bypass • Steady amber — The optic bypass module has been directed to pass traffic via the Cisco SCE8000. • Unlit — The optic bypass module (if present) will connect the link fibers directly, and traffic will bypass the Cisco SCE8000. On a slave SCE8000-SMC_E module (in the second slot), this LED is always off. Note This functionality is consistent even when the Cisco SCE8000 is powered down. Master Indicates the master Service Control module • Steady green — Master Service Control module • Unlit — Slave Service Control module Port1 and Port2 (Management interfaces) The Port1 and Port2 LEDs indicate the operational status of the Cisco SCE8000 out-of-band LAN-based management port, as follows: • Link/Active Steady green — Port link is up Flashing green — Activity on the port link Unlit — Port link is down • Speed Unlit — Port is set to 10Mbps Steady green — Port is set to 100 Mbps Steady amber — Port is set to 1000 Mbps On a slave SCE8000-SMC-E module (in the second slot), this LED is always off.

OL-16478-05 Chapter 2 Introduction to the Cisco SCE8000 10GBE Platform Introduction to SIPs and SPAs Introduction to SIPs and SPAs SIPs and SPAs are a new carrier card and port adapter architecture used to increase modularity, flexibility, and density for network connectivity. This section describes the SIPs and SPAs and provides some guidelines for their use. • SPA Interface Processors, page 2-5 • Specifying the SIP Subslot Location for a SPA, page 2-5 • Shared Port Adapters, page 2-6 • Modular Optics, page 2-6 • XFP Connections, page 2-7 SPA Interface Processors The SIP module supported by the Cisco SCE8000 chassis is the SCE8000-SIP. The following list describes some of the general characteristics of a SIP: • A SIP is a carrier card that inserts into a slot in the chassis like a line card. It provides no network connectivity on its own. • A SIP contains one or more subslots (bays), which are used to house one or more SPAs. The SPA provides interface ports for network connectivity. • During normal operation the SIP should reside in the SCE8000 chassis fully populated either with functional SPAs in all subslots, or with a blank filler plate (SPA-BLANK=) inserted in all empty subslots. Specifying the SIP Subslot Location for a SPA Cisco SCE8000-SIP subslots begin their numbering with “0” and have a horizontal orientation. Figure 2-3 shows the subslot numbering for the Cisco SCE8000-SIP. The Cisco SCE8000-SIP supports four subslots for the installation of SPAs, as follows: • SIP subslot 0—Top–left subslot • SIP subslot 1—Top–right subslot • SIP subslot 2—Bottom–left subslot • SIP subslot 3—Bottom–right subslot Figure 2-3 SPA Module Subslot Location Sub-slot 0 Front of SCE8000-SIP 270900 Sub-slot 1 Sub-slot 2 Sub-slot 3

OL-16478-05 Chapter 2 Introduction to the Cisco SCE8000 10GBE Platform Introduction to SIPs and SPAs Shared Port Adapters The SPA supported by the Cisco SCE8000-SIP is the 1-Port 10-Gigabit Ethernet SPA, SPA-1X10GE-L-V2 The following list describes some of the general characteristics of a SPA: • A SPA is a modular type of port adapter that inserts into a subslot of a compatible SIP carrier card to provide network connectivity and increased interface port density. The Cisco SCE8000-SIP can hold up to four SPAs. Since the interfaces are connected in subscriber/network pairs, either two or four SPAs must be installed. • The supported SPA is a single-height SPAs, which inserts into one SIP subslot. (See Figure 2-4.) Figure 2-4 Single-Height SPA Size • Each SPA provides a one 10GBE port, which is the interface to either subscriber or network traffic. These interfaces can be individually configured using the Cisco command-line interface (CLI). • Either a blank filler plate or a functional SPA should reside in every subslot of an SIP during normal operation to maintain cooling integrity. Blank filler plates are available in single-height form only. Since the interfaces are connected in subscriber/network pairs, the SCE8000-SIP must be either fully populated or have both the bottom bays covered with blank filler plates. Modular Optics The SPAs implement 10GBE small form-factor pluggable (XFP) optical transceivers to provide network connectivity (Figure 2-5). An XFP module is a transceiver device that mounts into the front panel to provide network connectivity. Note It is highly recommended only to use the XFP modules listed as supported in this document. Use of unsupported or unqualified XFP modules may affect reliability or operation. Single-height SPA Front of the SCE8000-SIP 242234 Single-height SPA Single-height SPA Single-height SPA

OL-16478-05 Chapter 2 Introduction to the Cisco SCE8000 10GBE Platform Introduction to SIPs and SPAs Figure 2-5 10GBE Small Form-factor Pluggable (XFP0) The interface connector on the 1-Port 10-Gigabit Ethernet SPA is a fiber optic receiver that supports one XFP. The types of optics modules that have been qualified for use with the 1-Port 10-Gigabit Ethernet SPA on the Cisco SCE8000 platform are as follows: • XFP-10GLR-OC192SR • XFP-10GER-OC192IR • XFP-10GZR-OC192LR • XFP-10G-MM-SR XFP Connections The qualified XFPs include an optical transmitter and receiver pair integrated with Clock and Data Recovery (CDR) integrated circuits. The XFPs provide high-speed serial links at 10.3125 Gbps on single mode fibers. Table 2-4 lists the XFP port cabling specifications. The transmit side recovers and retimes the 10 Gbps serial data and passes it to a laser driver. The laser driver biases and modulates a laser, enabling data transmission over fiber through an LC connector. The receive side recovers and retimes the 10 Gbps optical data stream from a photo detector trans impedance amplifier and passes it to an output driver. See the label on the XFP for technology type and model. XFP dimensions are: • Height 12.5 mm • Width 18.35 mm • Length 71.1mm The XFP operating temperature range is 0°C to 70°C. 129499 Table 2-4 XFP Port Cabling Specifications XFP Wavelength Fiber Type XFP-10GLR-OC192SR 1310 nm SMF XFP-10GER-OC192IR 1550 nm SMF XFP-10GZR-OC192LR 1550 nm SMF XFP-10G-MM-SR 850 nm MMF

OL-16478-05 Chapter 2 Introduction to the Cisco SCE8000 10GBE Platform Introduction to SIPs and SPAs The SCE8000-SIP Table 2-5 list the status and description of the SCE8000-SIP LED. The 1-Port 10GBE SPA Interface Module The SCE8000-SIP is installed in slot #3 of the Cisco SCE8000 chassis. It hosts up to four single-width, single-height 1-Port 10GBE SPA interface modules, but in the Cisco SCE8000, it must be configured with either two 1-Port 10GBE SPAs (in the top two subslots) or four 1-Port 10GBE SPAs, to provide interfaces for either one or two complete traffic links. Figure 2-6 provides an illustration of the SPA module and Table 2-6 lists the SPA module ports and Table 2-7 lists the SPA module LEDs. Figure 2-6 1-Port 10GBE SPA Interface Module Table 2-5 SCE8000-SIP LED LEDs Description Status • Green —Operational • Flashing Amber - Electrical bypass in operation • Red - Not initialized or failed • Unlit —No power STATUS 122151 ACTIVE/LINK SPA-1X10GE-L-V2 1 2

OL-16478-05 Chapter 2 Introduction to the Cisco SCE8000 10GBE Platform The Cisco SCE8000 Optical Bypass The Cisco SCE8000 Optical Bypass • Optical Bypass Functionality, page 2-10 • Optical Bypass Module (OPB-SCE8K), page 2-11 The Cisco SCE8000 platform optical bypass module preserves the service provider 10GBE links under all circumstances. At power failure the bypass is automatically activated. It can also be activated by the Cisco SCE8000 software. Table 2-6 SPA Ports Port Quantity Description Connect This Port To… 10 GBE Line port 1 on each SPA Any one of the following: • XFP-10GLR-OC192SR (10km) • XFP-10GER-OC192IR (40km) • XFP-10GZR-OC192LR (80km) • XFP-10G-MM-SR (300m) CLI designation: interface TenGigabitEthernet 3/0/0, 3/1/0/, 3/2/0, 3/3/0. Any one of the following: • Subscriber side network component • Network side network component • Optical bypass 10GBE line port • 10GBE line port of a cascaded SCE8000 platform • EtherChannel port of a Cisco 7600 Series router (MGSCP topology) Refer to Connecting the Line Ports to the Network, page 6-2for further information. Table 2-7 SPA LEDs LEDs Description Active/Link (1) • Green —Port is enabled by software and the link is up. • Amber — Port is enabled by software and the link is down. • Unlit — Port is not enabled by software. Status (2) The Status LED indicates the operational status of the SPA module, as follows: • Green — SPA is ready and operational. • Amber — SPA power is on and good, and SPA is being configured. • Off — SPA power is off.

OL-16478-05 Chapter 2 Introduction to the Cisco SCE8000 10GBE Platform The Cisco SCE8000 Optical Bypass The Cisco SCE8000-SIP module already includes an internal electrical bypass, but it is strongly recommended to use the optical bypass module for addressing the following scenarios: • During platform reboot (SW reload)—If the external bypass module is not used, there is a 10-second period (at most) during which the link is forced down (cutoff functionality). • During a power failure —The Cisco SCE8000 has two power supplies. A power failure occurs only when both of them fail. In a case where the Cisco SCE8000 platform must be replaced, it is possible to remove the bypass modules from the SCE8000 chassis without disconnecting them from the network and then reinstall them in the new SCE platform, so that traffic links are preserved even in a case of complete failure and replacement of the Cisco SCE8000 platform. (See Replacing the Optical Bypass Module without Disrupting Traffic on the Link, page 9-27.) Optical Bypass Functionality The optical bypass module is connected bump-in-the-wire in the 10-GBE link. It is then connected to the Cisco SCE8000 platform with two types of connections: • 10GBE optical connections for data link traffic — 10 GBE connections from the optical bypass module to one pair of the 10GBE SPA ports. • Control connection — Connection to the RJ-11 External Bypass connector on the SCE8000-SCM, so the optical bypass is activated if the Cisco SCE8000 platform fails. Optical Bypass Module Connectivity The optical bypass module functions as follows: • Under normal conditions, the bypass module directs traffic to flow via the Cisco SCE8000 (Figure 2-7). • Under failure conditions, the optical bypass shortcuts the interfaces that are connected to the traffic link, and all traffic flows through the optical bypass module, bypassing the SCE platform (Figure 2-7). Figure 2-7 Optical Bypass Module Connectivity 242125 Default bypass state (no power) Non-default bypass state OPB OPB 3/0/0 3/1/0 3/2/0 3/3/0 SCE8000

OL-16478-05 Chapter 2 Introduction to the Cisco SCE8000 10GBE Platform The Cisco SCE8000 Optical Bypass Optical Bypass Module (OPB-SCE8K) There are two types of optical bypass modules to support different optic types: • OPB-SCE8K-SM supports Single-Mode optics and should be used with SCE8000 equipped with Single-Mode optics. • OPB-SCE8K-MM supports Multi-Mode optics and should be used with SCE8000 equipped with Multi-Mode optics. The optical bypass module is installed either internally, in slot #4 of the Cisco SCE8000 chassis or in an external mounting panel in the rack. Up to two optical bypass modules can be mounted internally, supporting inline insertion into two links. Up to four optical bypass modules can be mounted using an external mount panel (OPB-SCE8K-EXT-PNL). A single panel can serve two SCE8000 platforms, each cutting two links or up to four SCE8000 platforms, each cutting a single link. The optical bypass module is displayed in Figure 2-8. Table 2-8 lists the optical bypass module ports and Table 2-9 lists the optical bypass module LEDs. Figure 2-8 Optical Bypass Module Table 2-8 Optical Bypass Module Ports Port Quantity Description Connect This Port To… 10 GBE Line port 4 10GBE ports A through D Duplex LC, panel mount adaptor for LC/UPC connectors SPA interfaces on the Cisco SCE8000. Refer to Cabling the 10GBE Line Interface Ports: Using the External Optical Bypass Module, page 6-13 for further information. CNTRL 1 RJ-11 port RJ-11 Optical Bypass port on the SCE8000-SCM-E TX RX A TX RX B TX RX C TX RX D A B A C C D B D STATUS CTRL OPB—SCE8K—MM 242235

OL-16478-05 Chapter 2 Introduction to the Cisco SCE8000 10GBE Platform The Cisco SCE8000 Optical Bypass Optical Bypass Module Specifications Fiber Cable Type The fiber cable type within the Optical Bypass Module area as follows: • OPB-SCE8K-MM: 50 um core. • OPB-SCE8K-SM: SMF-28 Maximum optical path (fiber length of two ports) is 600m. Switching Time Switching time is measured from trigger to stable 90% optical output. • Typical switching time: 3 ms • Maximal switching time: 10ms Fan Assembly The system fan assembly, located in the chassis, provides cooling air for the installed modules (Figure 2-9). Sensors on the fan assembly and within the system monitor the internal air temperatures. If the air temperature exceeds a preset threshold, the environmental monitor displays warning messages. Table 2-9 Optical Bypass Module LEDs LEDs Description Status The Status LED indicates the operational status of the optical bypass module, as follows: • Green — Bypass module has been de-activated (traffic flows through the Cisco SCE8000 platform) • Off — Bypass module is active (traffic does not flow through the Cisco SCE8000 platform)

OL-16478-05 Chapter 2 Introduction to the Cisco SCE8000 10GBE Platform The Cisco SCE8000 Optical Bypass Figure 2-9 Fan Assembly If an individual fan within the assembly fails, the FAN STATUS LED turns red. To replace a fan assembly, see Removing and Replacing the Fan Assembly, page 9-11. 270893 SYSTEM POWER OPTICAL BYPASS STATUS AUX PORT 2 LINK ACTIVE MASTER SCE8000 EXTENDED SERVICE CONTROL MODULE OPTICAL BYPASS OPTICAL BYPASS CONSOLE 10 100 1000 LINK ACTIVE PORT 1 A C A B C D B D STATUS CTRL OPB-SCE8K-MM OPTICAL BYPASS1 TX RX TX RX TX RX TX RX A C A B C D B D STATUS CTRL OPB-SCE8K-MM OPTICAL BYPASS2 TX RX TX RX TX RX TX RX SYSTEM POWER OPTICAL BYPASS STATUS AUX PORT 2 10 100 1000 LINK ACTIVE MASTER SCE8000 EXTENDED SERVICE CONTROL MODULE SCE8000-SCM-E SCE8000-SCM-E SCE8000-SIP CONSOLE 10 100 1000 LINK ACTIVE PORT 1 OPTICAL BYPASS OPTICAL BYPASS STATUS ACTIVE/LINK SPA-1X10GE-L-V2 STATUS ACTIVE/LINK SPA-1X10GE-L-V2 STATUS ACTIVE/LINK SPA-1X10GE-L-V2 STATUS ACTIVE/LINK SPA-1X10GE-L-V2 10 100 1000 FAN STATUS Captive installation screws

OL-16478-05 Chapter 2 Introduction to the Cisco SCE8000 10GBE Platform The Cisco SCE8000 Optical Bypass Power Supplies The Cisco SCE8000 platform supports redundant AC- or DC-input power supplies. The following power supplies are available for the Cisco SCE8000 platform: • 2700 W DC input (PWR-2700-DC/4): uses an external terminal block on the back side of the chassis for input power connection (Figure 2-11). • 2700 W AC input (PWR-2700-AC/4): uses an external power cord directly connected to the AC power supply (Figure 2-10). Figure 2-10 PWR-2700-AC/4 Figure 2-11 PWR-2700-DC/4 The AC-input and DC-input power supplies support redundancy. When power is removed from one supply, the redundant power feature causes the second supply to produce full power. 126565 Captive installation screws PWR-AC INPUT OK FAN OK OUTPUT FAIL ALL FASTENERS MUST BE FULLY ENGAGED PRIOR TO OPERATING THE POWER SUPPLY 100-240V-16A 50/60Hz Captive installation screws 132218 Captive installation screws Captive installation screws PWR-2700-DC/4 -VE-1 -VE-1 -VE-2 -VE-2 INPUT1 OK 48V-60V =40A INPUT2 OK 48V-60V =40A FAN OK OUTPUT FAIL ALL FASTENERS MUST BE FULLY ENGAGED PRIOR TO OPERATING THE POWER SUPPLY

OL-16478-05 Chapter 2 Introduction to the Cisco SCE8000 10GBE Platform Checking the Shipping Container Contents Power Supply Cooling Power supplies have built-in fans and are completely self-cooling. Air enters from the right of the fan and exits through the left. Load Sharing With two power supplies, each power supply concurrently provides approximately half of the required power to the system. If one power supply fails, the second power supply immediately assumes full power to maintain uninterrupted system operation. The second power supply enables load sharing and fault tolerance automatically; no software configuration is required. Checking the Shipping Container Contents Use the Cisco SCE8000 Component List to check the contents of the Cisco SCE8000 platform shipping container. Tip Do not discard the shipping container when you unpack the Cisco SCE8000. Flatten the shipping cartons and store them with the pallet. You will need these containers if you need to move or ship the Cisco SCE8000 in the future. Cisco SCE8000 Component List Table 2-10 lists the Cisco SCE8000 components. Table 2-10 Cisco SCE8000 Component List Component Description Cisco SCE8000 platform Cisco SCE8000 10GBE chassis configured with the following components: Cisco SCE8000-SCM-E Cisco SCE8000 Service Control Module Cisco SCE8000-SIP Cisco SCE8000 SPA Jacket card Interface Processor 2 or 4 SPA Jacket cards SPA Interface. See below the list of supported SPA models. 2 or 4 XFP OpticsXFP optic modules. See below the list of supported XFP models 2 Cisco PWR-2700-AC/4 or 2 Cisco PWR-2700-DC/4 Cisco power supply units, AC or DC. Hot swappable, redundant power supply. SCE8000-FAN Redundant fans unit. Accessories The following accessories might arrive in separate shipping containers: Management cables • Gigabit Ethernet cable for connecting to the Management ports • RS-232 serial cables (DB-9 to RJ-45 and DB-25 to RJ-45) for connecting to a local terminal

OL-16478-05 Chapter 2 Introduction to the Cisco SCE8000 10GBE Platform Checking the Shipping Container Contents Note Cisco does not ship the entire Cisco SCE8000 documentation set automatically with each system. You must specifically order the documentation as part of the sales order. If you ordered documentation and did not receive it, we will ship the documents to you within 24 hours. To order documents, contact a customer service representative. Power cables Two AC power supply cords, if ordered with AC-input power supply units Grounding kit 69-0815-01 • Grounding lug • Two M4 hex-head screws with locking washers Optical Bypass module kit • Optical Bypass Module • Control Cable (2 m) • Control Cable (40 cm) Table 2-10 Cisco SCE8000 Component List (continued) Component Description

OL-16478-05 Chapter 2 Introduction to the Cisco SCE8000 10GBE Platform Cisco SCE8000 Installation Checklist Cisco SCE8000 Installation Checklist To assist you with your installation and to provide a historical record of what was done by whom, photocopy the following Cisco SCE8000 Installation Checklist (Table 2-11). Indicate when each procedure or verification is completed. When the checklist is completed, place it in your site log along with the other records for your new Cisco SCE8000 platform. Table 2-11 Cisco SCE8000 Installation Checklist Task Verified By Date Date Cisco SCE8000 received Cisco SCE8000 and all accessories unpacked Safety recommendations and guidelines reviewed Topology verified: number of Cisco SCE8000 platforms, number of links, and whether inline or receive-only Installation Checklist copied Site log established and background information entered Site power voltages verified Site environmental specifications verified Required passwords, IP addresses, device names, and so on, needed for initial configuration available (refer to Initial Setup Parameters, page 5-2) Required tools available Network connection equipment available Cisco SCE8000 mounted in rack System grounding established, if required AC/DC power cables connected to AC/DC sources and Cisco SCE8000 chassis Optical bypass modules installed (optional) Console port set for 9600 baud, 8 data bits, no parity, and 1 stop bit (9600 8N1) ASCII terminal attached to console port Management port is operational Network interface cables and devices connected System power turned on System boot complete (Status LED is on) 10 GBE line ports operational Correct hardware configuration displayed after system banner appears

OL-16478-05 Chapter 2 Introduction to the Cisco SCE8000 10GBE Platform Cisco SCE8000 Installation Checklist