Black Box SS4P-SH-DP-U Quick Start Manual

ss4p-sh-dp-u_qsg_rev1.pdf 4-PORT, DP, SINGLE-HEAD OR DUAL-HEAD WITH OR WITHOUT CAC CUSTOMER SUPPORT INFORMATION ORDER TOLL-FREE IN THE U.S.: CALL 877-877-BBOX (OUTSIDE U.S. CALL 1-724-746-5500) FREE TECHNICAL SUPPORT 24 HOURS A DAY, 7 DAYS A WEEK: CALL 877-877-2269 WEB SITE: WWW.BLACKBOX.COM E-MAIL: [email protected] PART NUMBERS SS4P-SH-DP-U 4-Port, Single-Head, DisplayPort SS4P-SH-DP-UCAC 4-Port, Single-Head, DisplayPort, with CAC SS4P-DH-DP-U 4-Port, Dual-Head, DisplayPort SS4P-DH-DP-UCAC 4-Port, Dual-Head, DisplayPort, with CAC 5 1.877.877.2269 BLACKBOX.COM 1.877.877.2269 BLACKBOX.COM QUICK START GUIDE WHAT’S IN THE BOX SS4P-SH-DP-U, SS4P-SH-DP-UCAC, SS4P-DH-DP-U, SS4P-DH-DP-UCAC QUICK START GUIDE 24/7 TECHNICAL SUPPORT AT 1.877.877.2269 OR VISIT BLACKBOX.COM SECURE KVM SWITCH SPECIFICATIONS VIDEO HOST INTERFACE 4-Port SH: (4) DisplayPort 20-pin F; 4-Port DH: (8) DisplayPort 20-pin F USER CONSOLE INTERFACE 4-Port SH: (1) DisplayPort 20-pin F; 4-Port DH: (2) DisplayPort 20-pin F MAXIMUM RESOLUTION 3840 x 2160 @ 30 Hz DDC 5 volts p-p (TTL) INPUT EQUALIZATION Automatic INPUT CABLE LENGTH Up to 20 ft. (6.1m) OUTPUT CABLE LENGTH Up to 20 ft. (6.1m) USB SIGNAL TYPE USB 1.1 keyboard and mouse only USB CONNECTORS 4-Port SH or DH: (4) USB Type B; 4-Port SH w/CAC or DH w/CAC: (8) USB Type B USER CONSOLE INTERFACE All: (2) USB Type A for keyboard/ mouse connections; 4-Port SH w/CAC or DH w/CAC: (1) USB Type A for CAC AUDIO INPUT (4) 3.5-mm female stereo connectors OUTPUT (1) 3.5-mm female stereo connector POWER POWER REQUIREMENTS (1) 12-VDC, 3-A power adapter with center-pin positive polarity ENVIRONMENT OPERATING TEMPERATURE 32 to 104° F (0 to 40° C) STORAGE TEMPERATURE -4 to +140° F (-20 to +60° C) HUMIDITY 0 to 80% relative humidity, noncondensing OTHER EMULATION Keyboard, mouse and video USER CONTROLS Front-panel buttons

monitor’s EDID upon power up. In the event of connecting a new monitor to the KVM, a power re-cycle is required. The KVM switch will indicate the unit’s EDID learn process is active by flashing the front panel’s LEDs in sequential order. Starting with the LED above button “1” on the front panel, each LED will flash green for approximately 10 seconds upon beginning the EDID learn. Once all the LEDs stop flashing, the LEDs will cycle and the EDID learn will be complete. If the KVM switch has more than one video board (such as dual-head and quad-head models), then the unit will continue to learn the EDIDs of the connected monitors and indicate the progress of the process by flashing the next port selection green and push button blue LEDs respectively.- A monitor must be connected to the video output port located in the console space at the back of the KVM switch during the EDID learn process. If the read EDID from the connected monitor is identical to the current stored EDID in the KVM switch, then the EDID learn function will be skipped. A full Manual can be downloaded from: WWW.BLACKBOX.COM HARDWARE INSTALLATION 1. Ensure that power is turned off or disconnected from the unit and the computers. 2. Use a DisplayPort cable to connect the DisplayPort output port from each computer to the corresponding DisplayPort IN ports of the unit. 3. Use a USB cable (Type-A to Type-B) to connect a USB port on each computer to the respective USB ports of the unit. 4. Optionally, for CAC models, connect a CAC (Common Access Card, Smart Card Reader) to the CAC port in the user console interface. 5. Optionally, connect a stereo audio cable (3.5-mm to 3.5-mm) to connect the audio output of the computers to the AUDIO IN ports of the unit. 6. Connect monitor(s) to the DisplayPort OUT console port of the unit using a DisplayPort cable. NOTE: You can connect one monitor to the single-head KVM switch and two monitors to the dual-head KVM switch. 7. Connect a USB keyboard and mouse in the two USB console ports. 8. Optionally, connect stereo speakers to the AUDIO OUT port of the unit. 9. Finally, power on the KVM switch by connecting a 12-VDC power supply to the power connector, and then turn on all the computers. NOTE: The computer connected to port 1 will always be selected by default after power up. NOTE: You can connect up to 4 computers to the 4 port KVM switch. FIGURE 3. DUAL-HEAD APPLICATION DIAGRAM 1 2 3 4 4 PORT DP W/ AUDIO SECURE KVM SWITCH DP OUT AUDIO IN USB IN USB OUT AUDIO OUT DP IN SS4P-DH-DP-U FIGURE 2. SINGLE-HEAD APPLICATION DIAGRAM FIGURE 1. DISPLAYPORT CONNECTOR 1 2 3 4 4 PORT DP W/ AUDIO SECURE KVM SWITCH DP OUT AUDIO IN USB IN USB OUT AUDIO OUT DP IN SS4P-SH-DP-U QUICK START GUIDE QUICK START GUIDE QUICK START GUIDE DisplayPort connector 1.877.877.2269 BLACKBOX.COM 3 1.877.877.2269 BLACKBOX.COM 4 1.877.877.2269 BLACKBOX.COM