Chroma AutoLED II Quick Start Manual

AutoLED II Quick Start Guide V1.053 PN: 637-0701 Approvals & Disclaimer The information contained herein is offered in good faith and is believed to be accurate. However, because conditions and methods of use of our products are beyond our control, this information should not be used in substitution for customer's tests to ensure that Chroma-Q products are safe, effective, and fully satisfactory for the intended end use. Suggestions of use shall not be taken as inducements to infringe any patent. Chroma-Q sole warranty is that the product will meet the Chroma-Q sales specifications in effect at the time of shipment. Your exclusive remedy for breach of such warranty is limited to refund of purchase price or replacement of any product shown to be other than as warranted. Chroma-Q reserves the right to change or make alteration to devices and their functionality without notice due to on-going research and development. The Chroma-Q AutoLED II has been designed specifically for the lighting industry. Regular maintenance should be performed to ensure that the products perform well in the entertainment environment. If you experience any difficulties with any Chroma-Q products please contact your selling dealer. If your selling dealer is unable to help please contact [email protected]. If the selling dealer is unable to satisfy your servicing needs, please contact the following for full factory service: Outside North America: North America: Tel: +44 (0)1494 446000 Tel: +1 416-255-9494 Fax: +44 (0)1494 461024 Fax: +1 416-255-3514 [email protected] [email protected] For further information please visit the Chroma-Q website at www.chroma-q.com. Chroma-Q and AutoLED II are trademarks, for more information on this visit www.chroma-q.com/trademarks. The rights and ownership of all trademarks are recognised. Quick Start Guide Chroma-Q® AutoLED II™ For a full product manual please visit www.chroma-q.com Software Version 1.05

AutoLED II Quick Start Guide V1.053 1. Overview The new Chroma-Q®™ AutoLED II™ is a 6,500K CCT, Daylight Moving Yoke LED fixture with 48 cold white high powered LEDs. The model is equipped with a built-in power supply and remotely controlled through ANSI E1.11 USITT DMX 512-A protocol. 2. Safety Caution 1. This product is for professional use only. It is NOT intended for domestic or outdoor use. 2. The bright flash of light during power-up & continuous strobe may cause epileptic seizure. 3. This product must be used with safety cable. 3. Cabling The AutoLED II utilises an IEC chassis connector for power input. The DMX control data input and through connections from an external control console are via two XLR 5-pin connectors. The chassis is ground bonded. 4. Mounting The AutoLED II fixture base is floor mount. The bottom of the fixture base has provisions to fasten the mounting bracket for overhead truss mounting applications. Note: Secure the fixture with a safety bond. Provision for a fixing hold is built into the fixture base. 5. Accessories Louver: A louver is fastened to the front of the AutoLED II fixture head. The louver can be detached from the fixture head by removing 2 screws. Beam Shaper: An optional Beam Shaper attachment can be placed onto the front of the AutoLED II fixture head. The Beam Shaper attachment is a diffuser film which can be controlled (On/Off) via DMX. There are 2 pins at the rear side of the Beam Shaping Attachment. The 2 pins match the 2 holes at the front of the AutoLED II fixture head. To attach the Beam Shaper, 1. Remove the louver 2. Match the 2 pins underneath the Beam Shaper attachment to the holes on the LED head 3. Align, set and fasten (with 2 screws) the Beam Shaper attachment onto the LED head with the 2 pins in the holes 4. Set the Diffuser Control on the display screen. (See Control Menu > Setup Menu > Technical) 6. Moving Yoke Pan & Tilt Movement 1 DMX channel is assigned to each movement: Pan 1 DMX channel Pan (fine movement) 1 DMX channel Tilt 1 DMX channel Tilt (fine movement) 1 DMX channel Maximum range of Movement & Direction: Movement Range Direction Pan 540° Normal or Reverse Tilt 270° Normal or Reverse 7. Power Switch The Power ON ON ON ON/OFF OFF OFF OFF switch is located at the rear of the fixture base. The Touch Screen LCD display at the front of the fixture base lights up to show the opening screen when the switch is turned to ON ON ON ON. 8. Control The control functions of the AutoLED II are accessed through the Touch Screen LCD display in front of the fixture. The features of the Touch Screen LCD display are: Screen menu title The fixture name or mode name is displayed on top of the screen. Control Information DMX address, footprint channels, mode name, values and indicators that appear after the command buttons are tapped. Command buttons Buttons which can be tapped to access control functions and options. Locked Default sets the screen to switch off & lock if untouched for 30 sec. Tap the screen to activate then press & hold the lock symbol for 5 sec. Control Menu Main Menu: displays the fixture name, control information and the main command buttons: Control Information: Address DMX start address Footprint DMX channels assigned Diffuser Status: On/Off Pan Dir Pan direction Tilt Dir Tilt direction Command Buttons: Change Add Change Add Change Add Change Add Change DMX start address Setup Menu Setup Menu Setup Menu Setup Menu Change internal settings 1. Tap a command button to access the control options available. 2. Tap Apply Apply Apply Apply to save or Escape Escape Escape Escape to return to Main Menu. Change Add Change Add Change Add Change Add Change DMX Address Use the numeric buttons to change the DMX start address, Setup Menu Setup Menu Setup Menu Setup Menu In this menu, internal settings of the fixture can be re-configured. Command Buttons: Screen Screen Screen Screen Display rotation, Lock screen Technical Technical Technical Technical DMX Data, Frequency, Upload Engine & Diffuser Control Direction Direction Direction Direction Pan Direction, Tilt Direction Operation Operation Operation Operation DMX Lost, Fan Speed, Reset Screen Screen Screen Screen In this menu, the display screen can be set and locked. RotateDisp RotateDisp RotateDisp RotateDisp Rotate the display screen by 180 degree LockScreen LockScreen LockScreen LockScreen Enable or disable display screen lock Technical Technical Technical Technical In this menu, the following command options are available: DMX Data DMX Data DMX Data DMX Data DMX data can be accessed Frequency Frequency Frequency Frequency The fixture can be set with four frequency options: 1200Hz 1200Hz 1200Hz 1200Hz, 2400Hz 2400Hz 2400Hz 2400Hz, 4800Hz 4800Hz 4800Hz 4800Hz, 9600Hz 9600Hz 9600Hz 9600Hz Upload ENG Upload ENG Upload ENG Upload ENG LED Engine software can be uploaded to the fixture from an external source by activating this menu Diffus CTL Diffus CTL Diffus CTL Diffus CTL Beam Shaper attachment is enabled or disabled in the Diffuser Control command. When Diffuser Control is On, the DMX channel for Diffuser Control is added and the Footprint will have 6 DMX channels. Direction Direction Direction Direction In this menu, the direction of the yoke and head Pan & Tilt movement can be set. Operation Operation Operation Operation In this menu, the following command options are available: DMX Lost DMX Lost DMX Lost DMX Lost Select between Last data Last data Last data Last data or No output No output No output No output Fan Spee Fan Spee Fan Spee Fan Speedddd Select between Low Low Low Low or High High High High Reset Reset Reset Reset Reset to Factory Default Factory Default Factory Default Factory Default or User User User User saved settings Factory Default Settings: DMX Address – 1 Direction – Normal Lock – Enable DMX Lost – Last Data Frequency – 1200Hz Fan Speed – High Diffus CTL – Off Reset - Default 9. Further Information Please refer to the Chroma-Q AutoLED II manual for more detailed information. A copy of the manual can be found at the Chroma-Q website – www.chroma-q.com – under Support.