CHC LT600 SERIES Getting Started Manual
Read Online
Read the CHC LT600 SERIES Getting Started Manual online using the built-in PDF viewer.
Text of the manual
CONTENTS
1. Introduction ................................................................................................................... 3
1.1.
Technical Assistance ........................................................................................ 3
1.2.
Your Comments ............................................................................................... 3
1.3.
Safety Information .......................................................................................... 3
1.4.
Warning and Cautions ..................................................................................... 3
1.5.
Use and Care ................................................................................................... 3
2. Overview ........................................................................................................................ 5
2.1.
Features ........................................................................................................... 5
2.2.
Specifications .................................................................................................. 5
3. LT600 Overview ............................................................................................................. 7
3.1.
Front View ....................................................................................................... 7
3.2.
Back View ........................................................................................................ 9
3.3.
Side View ...................................................................................................... 10
4. Basic Operation ........................................................................................................... 11
4.1.
Insert SIM Card and power on ...................................................................... 11
4.2.
Language & input .......................................................................................... 13
4.3.
Set Date/Time ............................................................................................... 13
4.4.
Display ........................................................................................................... 14
4.5.
WIFI ............................................................................................................... 16
4.6.
Bluetooth ...................................................................................................... 16
4.7.
USB Connection ............................................................................................ 17
4.8.
Use Camera ................................................................................................... 18
4.9.
Scheduled power on & off ............................................................................ 19
4.10.
Location ......................................................................................................... 20
5. Getting Started With Map Cloud 3.0 ........................................................................... 21
5.1.
Build New Project .......................................................................................... 21
5.2.
Coordinate System Settings .......................................................................... 22
5.3.
Import Base Map........................................................................................... 23
5.4.
Data Collection .............................................................................................. 24
5.5.
Export Data ................................................................................................... 25
5.6.
Software Registration .................................................................................... 26
6. Getting Started With GNSSTool ................................................................................... 27
6.1.
Connection .................................................................................................... 27
6.2.
CORS Login .................................................................................................... 29
6.3.
Sky Plot .......................................................................................................... 30
6.4.
Debugging Data ............................................................................................. 31
If you have a problem and cannot find the information you need in the product
documentation, contact your local dealer from which you purchased the LT600 Series.
Alternatively, please request technical support using the CHC Website (www.chcnav.com) or
CHC technical support email ([email protected]).
1.2.
YOUR COMMENTS
Your feedback about this Getting Started Guide will help us to improve it in future revision.
Please e‐mail your comments to [email protected].
1.3.
SAFETY INFORMATION
This manual describes CHC LT600 Series GNSS Data Collecting Terminal. Before using the
LT600 Series, please make sure that you have read and understood this Getting Started
Guide, as well as the safety requirements.
1.4.
WARNING AND CAUTIONS
An absence of specific alerts does not mean that there are no safety risks involved.
A Warning or Caution information is intended to minimize the risk of personal injury and/or
damage to the equipment.
WARNING ‐ A Warning alerts you to a potential misused or wrong setting of the
equipment.
CAUTION ‐ A Caution alerts you to a possible risk of serious injury to your person
and/or damage to the equipment.
1.5.
USE AND CARE
field. However, the LT600 Series is high‐precision electronic equipment and should be
treated with reasonable care.
LT600 is a high accuracy GNSS data collecting terminal independently developed by CHC,
which adopts industrial third level design, IP65 protection level. Positioning accuracy of the
LT600 could reach decimeter, with alternative configuration of 1D/2D code scanning, RFTD,
Infrared and MIC so on. Equipped with high sensitive point touch pen, LT600 makes it more
convenient to collect data and map ground. 4G cellular modem with Dual‐SIM‐Dual‐Standby
offers more choices of experiencing high speed data transmitting. With 8 inch screen and
16:9 scale, LT600 provides you more open vision and more convenience.
2.2.
SPECIFICATIONS
LT600
Operating System
Android 5.1
CPU
Quad‐core 1GHz
RAM
2GB
Flash Memory
32GB
Memory Extend
Micro SD, up to 128G
GNSS
Support GPS+GLONASS or GPS+BDS
Accuracy
Stand alone:2‐5m; SBAS: 2m
Channel
72
Cold Start
30s
Warm Start
1s
WIFI
802.11 b/g/n
Cellular Modem
LTE,
EDGE, GSM,GPRS
Bluetooth
V4.1
USB
Micro USB, OTG( support hot plug)
Bar Code
1D/2D bar code scanner(optional)
Li‐ion Battery
9000mAh
Voltage
3.8V
Battery Life
>12h(continuous work)
Charging Time
<4h
Front Camera
2.0 megapixel
Back Camera
8.0 megapixel
MIC
Support
Flash Light
Support
· MIC :Support
Page 7
3. LT600 OVERVIEW
3.1.
FRONT VIEW
Power Button
‐
Turn ON: Press the button for 1‐2 seconds, the Power Indicator will turn on and the boot
screen will appear, and then the LT600 will enter the operation system after 30 seconds.
‐
Turn OFF: Press the button for 1‐2 seconds, the “SELECT” dialogue box will pop up, select
“Power off” to turn off the device.
‐
Restart: Press the button for 1‐2 seconds, the “SELECT” dialogue box will pop up, select
“Restart” to restart the device.
Page 8
Menu Button
Click this button to bring out the start menu.
Home Button
Use the home button to return main menu.
Return Button
Press this button to go back to previous menu.
SIM
Insert SIM card into this card slot.
TF
Insert TF card into this card slot.
Charging/Data Interface
This interface is used for battery charging and data transmission between LT600 and PC using
USB cable.
Headset Jack
Insert your headset into this socket.
Figure 1 Figure 2
Click
to make a phone call.
Click
to access contacts information.
Click
to open messaging.
Click
to open browser.
Click
to open the drawer to see all the apps that have been installed (Figure 2).
Figure 3 Figure 4
Use virtual button key to facilitate your operation with LT600.
Click
to go back to previous menu.
Click
to return home screen.
Click
to see all the running apps (Fig. 3) and then you can remove apps by sliding
them towards left or right side(Fig. 4).
After powering on LT 600 (refer to 4.2 Power on), Click Settings/SIM card to turn on
the SIM cards.
Page 13
4.2.
LANGUAGE & INPUT
Click Settings/Language & input/Language to select language.
4.3.
SET DATE/TIME
Click Settings/Date & time and enter Date & time interface.
YOU CAN ALSO CUSTOMIZE YOUR TIME ZONE AND CHOOSE WHETHER TO USE 24‐HOUR FORMAT IN THIS
INTERFACE.
4.4.
DISPLAY
Click Settings/Display to enter Display interface.
Page 15
Brightness adjusting: Click Brightness level to adjust it according to your preference.
Sleep: Click to optimize the inactivity time LT600 needs to close screen.
Font size: Click to change the font size.
Page 16
4.5.
WIFI
Click Settings/WIFI to switch on the button.
Select WIFI and type in its password to connect.
4.6.
BLUETOOTH
Click Settings/Bluetooth to turn on the Bluetooth.
You can also use third party software to manage the documents and data stored in
Page 18
LT600 and install software like MapCloud3.0, GNSSTool into it.
4.8.
USE CAMERA
Make sure that the battery is charged and installed in the receiver.
Click to start recording the video, click again to finish.
Click to take a photo.
Slide fingers in the left column to switch between 5 different modes:
Normal mode
PIP mode
Live photo mo:
Panarama mode
Multi angle view mode
Camera Settings
Click to configure related parameters
Page 19
4.9. SCHEDULED POWER ON & OFF
LT600 allows users to achieve scheduled power on and off by setting the power up & off
time and repeat time beforehand.
Set the Scheduled power on time and click OK.
Set scheduled power on repeat time and click OK.
Page 20
Scheduled power off time settings is the same with Scheduled power on.
4.10. LOCATION
Click Settings/Location to switch on location service.
Open MapCloud3.0 and click "+" to build new project > choose "Project Template" and
"Coordinate System" >click "√" to finish;
Click satellite icon in the upper right corner >click "Connect" >choose "Connect Method,
Device Type" >Local Connection Successful >Return.
Click Menu >"Settings" >"Coordinate System" >"Projection Parameters" >Set “Central
Meridian” and “East Shifting” >click "√" to save;
Type in 3 or 7 parameters, or open “Site Calibration” >click "+" to add known point >click
“Calculate” > click "√" to save and then starts collecting.
5.3.
IMPORT BASE MAP
Click menu button of hand‐held receiver >”Import” >”Import Vector Data” or “Import
Map” > choose the file to be imported.
Page 24
5.4.
DATA COLLECTION
Click the button in the lower right corner >”Point” >”GPS” >click save to finish collecting (the
same for line or area collecting)
Page 25
5.5.
EXPORT DATA
Click menu button of the hand‐held receiver >"Export" >click “Export Vector Data” >choose
the point/line/area layer and its format you want to export >click "√" to export.
Page 26
5.6.
SOFTWARE REGISTRATION
Register in the upper right corner of GNSS Server contains GNSS Server version, device ID
and so on; Software registration set by MapCloud3.0 include the version of MapCloud3.0,
device ID etc. Users can register by applying for registration code from CHC.
connection. External App can send command to receiver by using GNSSTool through
broadcast. GNSSTool can call CHC SDK to send command to receiver. Users only need to
connect with GNSSTool to communicate with the receiver. It will be running in the
background once connected and users don’t need to start it.
Before using GNSSTool, users need to register first. Unregistered GNSSTool only allow for 30
minutes tryout.
6.1.
CONNECTION
1. Open GNSSTool, click [Connect] menu and select [Device Type] and [Connection Type] /
[Device ID] in connect interface.
2. Device Type: GNSSTool currently supports 4 types of Device: Smart RTK, GNSS RTK,
Local and Peripheral. Local supports typical mobile phone and CHC customized handheld
controller like LT40 and LT600. Peripheral supports NMEA0183, X360 Series and other
devices.
Here for LT600, we choose Local.
Page 28
3. Connection Type: For smart RTK (like i80), we select Bluetooth, WIFI or Demonstration.
For GNSS RTK (like X91), we select Bluetooth, and Demonstration. For Local and Peripheral,
we select the specific device type that we use. Here we select LT600 for Connection Type.
please make sure the device has been connected and the handheld is connected to the
1. Click Diff Data Source in the main interface, type in IP, Port, Source Table and other
parameters and then click LOGIN.
6.3.
SKY PLOT
Click Sky Plot and see how many satellites (including GPS, GLONASS, BDS, GALILEO and SBAS)
the device is currently tracking.
Page 31
6.4.
DEBUGGING DATA
Click Debugging Data to enter data debugging interface. Click HEX to change the data into
txt format, or pause, save and clear the data using button in the upper side.
CHC ‐ Shanghai HuaCe Navigation Technology Ltd.
Building C,599 Gaojing Road,Qingpu
District,Shanghai,China
Tel: +86-21-51508100-1241
Fax: +86-21-64851208
Email: [email protected] | [email protected]
Website: www.chcnav.com
The SAR limit of USA (FCC)is 1.6W/Kg averaged over one gram of tissue. Product, model
number:LT-600;(FCC ID:SY4-B01008) has also been tested against this SAR limit. The
highest SAR value reported under this standard during product certification for use on the
body is 1.15 W/Kg .The device was test for body-worn operations & hotspot operations .
compliance with FCC RF exposure requirements
RF Exposure Information (SAR) :
This device complies with part 15 of the FCC Rules. Operation is subject to the following Two
conditions:(1) This device may not cause harmful interference , and (2)this device must accept
any interference received, including interference that may cause undesired operation.
Any changes or modifications not expressly approved by the party responsible for compliance
could void the user's authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates,
uses and can radiate radio frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications. However, there is
no guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the interference by
one or more of the following measures:
—Reorient or relocate the receiving antenna.
—Increase the separation between the equipment and receiver.
—Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
—Consult the dealer or an experienced radio/TV technician for help.
