Omron E5CC-U Instruction Manual

Download Omron E5CC-U PDF Manual (2 pages)

Text of the manual

Indicates a potentially hazardous situation which, if

not avoided, is likely to result in minor or moderate injury or property damage. Read this manual carefully before using the product. E5CC-U Digital Controller Be sure to observe the following precautions to prevent operation failure, malfunction, or adverse affects on the performance and functions of the product. Not doing so may occasionally result in unexpected events. Use the product within specifications. (1) The product is designed for indoor use only. Do not use the product outdoors. Do not use or store the product in any of the following locations. •Places directly subject to heat radiated from heating equipment. •Places subject to splashing liquid or oil atmosphere. •Places subject to direct sunlight. •Places subject to dust or corrosive gas (in particular, sulfide gas and ammonia gas). •Places subject to intense temperature change. •Places subject to icing and condensation. •Places subject to vibration and large shocks. (2) Use/store within the rated temperature and humidity ranges. Provide forced-cooling if required. (3) To allow heat to escape, do not block the area around the product. Do not block the ventilation holes on the product. (4) Be sure to wire properly with correct polarity of terminals. (5) Use the specified size of crimped terminals (M3.5, width 7.2 mm or less) for wiring. To connect bare wires to the terminal block, use copper braided or solid wires with a gage of AWG24 to AWG14 (equal to cross- sectional area of 0.205 to 2.081 mm2). (The stripping length is 5 to 6 mm.) Up to two wires of same size and type, or two crimped terminals can be inserted into a single terminal. (6) Do not wire the terminals which are not used. (7) Allow as much space as possible between the controller and devices that generate a powerful high- frequency or surge. Separate the high-voltage or large-current power lines from other lines, and avoid parallel or common wiring with the power lines when you are wiring to the terminals. (8) Use this product within the rated load and power supply. (9) Make sure that the rated voltage is attained within two seconds of turning ON the power using a switch or relay contact. If the voltage is applied gradually, the power may not be reset or output malfunctions may occur. (10) Make sure that the Digital Controller has 30 minutes or more to warm up after turning ON the power before starting actual control operations to ensure the correct temperature display. (11) When executing self-tuning, turn the load and the unit ON simultaneously, or turn the load ON before you turn the controller ON. (12) A switch or circuit breaker should be provided close to this unit. The switch or circuit breaker should be within easy reach of the operator, and must be marked as a disconnecting means for this unit. (13) Wipe off any dirt from the Digital Controller with a soft dry cloth. Never use thinners, benzine, alcohol, or any cleaners that contain these or other organic solvents. Deformation or discoloration may occur. (14) Design system (control panel, etc) considering the 2 second of delay that the controller’s output to be set after power ON. (15) The output will turn OFF when you move to the Initial Setting Level. Take this into consideration when performing control. (16) The number of non-volatile memory write operations is limited. Therefore, use RAM write mode when frequently overwriting data during communications or other operations. (17) When disassembling the Temperature Controller for disposal, use suitable tools. (18) Do not turn the power supply to the Digital Controller ON or OFF while the USB-Serial Conversion Cable is connected. The Digital Controller may malfunction. (19) The terminals can reach temperature of up to 65℃. Precautions for Safe Use Refer to the E5�C Digital Controllers User’s Manual (Man. No. H174) for detailed application procedures. INSTRUCTION MANUAL Thank you for purchasing the OMRON E5CC-U Digital Controller. This manual describes the functions, performance, and application methods needed for optimum use of the product. Please observe the following items when using the product. • This product is designed for use by qualified personnel with a knowledge of electrical systems. • Before using the product, thoroughly read and understand this manual to ensure correct use. • Keep this manual in a safe location so that it is available for reference whenever required. OMRON Corporation ©All Rights Reserved Refer to the E5�C Digital Controllers User’s Manual (Man. No. H174) for information on the Advanced Function Setting Level, Manual Control Level, and other functions. Suitability for Use Omron Companies shall not be responsible for conformity with any standards, codes or regulations which apply to the combination of the Product in the Buyer’s application or use of the Product. At Buyer’s request, Omron will provide applicable third party certification documents identifying ratings and limitations of use which apply to the Product. This information by itself is not sufficient for a complete determination of the suitability of the Product in combination with the end product, machine, system, or other application or use. Buyer shall be solely responsible for determining appropriateness of the particular product with respect to Buyer’s application, product or system. Buyer shall take application responsibility in all cases. NEVER USE THE PRODUCT FOR AN APPLICATION INVOLVING SERIOUS RISK TO LIFE OR PROPERTY WITHOUT ENSURING THAT THE SYSTEM AS A WHOLE HAS BEEN DESIGNED TO ADDRESS THE RISKS, AND THAT THE OMRON PRODUCT(S) IS PROPERLY RATED AND INSTALLED FOR THE INTENDED USE WITHIN THE OVERALL EQUIPMENT OR SYSTEM. Power supply voltage 100 to 240 VAC, 50/60 Hz or 24 VAC, 50/60 Hz / 24 VDC Operating voltage range 85 to 110% of the rated voltage Power consumption 5.2 VA max. (100 to 240 VAC) 3.1 VA max. (24 VAC) 1.6 W max. (24 VDC) Indication accuracy Thermocouple: (Ambient temperature: 23°C) (±1.0 % of indication value or ±2°C, whichever is greater) ±1 digit max. Platinum resistance thermometer: (±0.2 % of indication value or ±0.8°C, whichever is greater) ±1 digit max. Analog input: ±0.2 % FS ±1 digit max. Control output 1 Relay output: SPDT, 250 VAC, 3 A (resistive load) Electrical life of relay: 100,000 operations Voltage output (for driving SSR): 12 VDC ±20%, 21 mA Linear current output: 4 to 20 mA DC, 0 to 20 mA DC Load: 500 � max. Control method ON/OFF or 2-PID control Auxiliary outputs Relay outputs:SPST-NO, 250 VAC, 3 A (resistive load) Electrical life of relay: 100,000 operations Ambient temperature -10 to 55°C (Avoid freezing or condensation) Ambient humidity 25% to 85% Storage temperature -25 to 65°C (Avoid freezing or condensation) Altitude Max. 2,000m Recommended fuse T2A, 250 VAC, time-lag, low-breaking capacity Weight Approx. 100 g (Digital Controller only) Degree of protection Front panel: IP50 Rear case: IP20 Terminal section: IP00 Installation environment Installation category II, pollution degree 2 (as per IEC61010-1) Memory protection Non-volatile memory (Number of write operations: 1,000,000) Temporary overvoltage Long-term:250V+(Power supply voltage) Short-term:1200V+(Power supply voltage) CAUTION CAUTION Minor injury due to electric shock may occasionally occur. Do not touch the terminals while power is being supplied. Electric shock, fire, or malfunction may occasionally occur. Do not allow metal objects, conductors, cuttings from installation work, or moisture to enter the Digital Controller, the Setup Tool ports, or between the pins on the connectors on the Setup Tool cable. Do not use the product where subject to flammable or explosive gas. Otherwise, minor injury from explosion may occasionally occur. Never disassemble, modify, or repair the product or touch any of the internal parts. Minor electric shock, fire, or malfunction may occasionally occur. CAUTION - Risk of Fire and Electric Shock a) This product is UL listed as Open Type Process Control Equipment. It must be mounted in an enclosure that does not allow fire to escape externally. b) More than one disconnect switch may be required to de-energize the equipment before servicing. c) Signal inputs are SELV, limited energy. d) Caution: To reduce the risk of fire or electric shock, do not interconnect the outputs of different Class 2 circuits. If the output relays are used past their life expectancy, contact fusing or burning may occasionally occur. Always consider the application conditions and use the output relays within their rated load and electrical life expectancy. The life expectancy of output relays varies considerably with the output load and switching conditions. Loose screws may occasionally result in fire. Tighten the terminal screws to the specified torque of 0.5 N•m. Set the parameters of the product so that they are suitable for the system being controlled. If they are not suitable, unexpected operation may occasionally result in property damage or accidents. A malfunction in the Digital Controller may occasionally make control operations impossible or prevent alarm outputs, resulting in property damage. To maintain safety in the event of malfunction of the Digital Controller, take appropriate safety measures, such as installing a monitoring device on a separate line. EN Safety Precautions Key to Warning Symbols Dimensions Warning Symbols Specifications Wiring Operation Menu *1: Upper and lower limits can be set for parameters 1, 4 and 5 to provide for different types of alarm. These are indicated by the letter "L" and "H". • The default alarm type is "2" Alarms *2: Error shown only for "Process value / Set point". Not shown for other status. When an error has occurred, the No.1 display shows the error code. Take necessary measure according to the error code, referring the table below. If the input value exceeds the display limit (-1999 to 9999), though it is within the control range, [[[[ will be displayed under -1999 and ]]]] above 9999. Under these conditions, control output and alarm output will operate normally. Refer to the E5�C Digital Controllers User’s Manual (Man.No.H174) for the controllable ranges. Check the setting of the Input Type parameter, check the input wiring, and check for broken or shorts in the temperature sensor. Turn the power OFF then back ON again. If the display remains the same, the controller must be repaired. If the display is restored to normal, then a probable cause can be external noise affecting the control system. Check for external noise. After the check of Input error, turn the power OFF then back ON again. If the display remains the same, the controller must be repaired. If the display is restored to normal, then a probable cause can be external noise affecting the control system. Check for external noise. No.1 display Meaning A/D converter error *2 Memory error Input error *2 s.err (S. Err) e111 (E111) Action OFF Alarm Control output Status at error OFF OFF Operates as above the upper limit. OFF OFF e333 (E333) Error Display (troubleshooting) OMRON EUROPE B.V. Wegalaan 67-69, NL-2132 JD Hoofddorp The Netherlands Phone 31-2356-81-300 FAX 31-2356-81-388 OMRON ELECTRONICS LLC One Commerce Drive Schaumburg, IL 60173-5302 U.S.A Phone 1-847-843-7900 FAX 1-847-843-7787 OMRON ASIA PACIFIC PTE. LTD. No. 438A Alexandra Road # 05-05/08 (Lobby 2), Alexandra Technopark, Singapore 119967 Phone 65-6835-3011 FAX 65-6835-2711 OMRON Corporation Shiokoji Horikawa, Shimogyo-ku, Kyoto 600-8530 JAPAN Use the following ranges for scaling: -1999 to 9999, -199.9 to 999.9, -19.99 to 99.99, -1.999 to 9.999 Analog input type Current input Voltage input Dimensions (mm) *1 *1 *1 Alarm type Vary with "L", "H" values Vary with "L", "H" values Vary with "L", "H" values No alarm function Output off Deviation upper/lower limit standby sequence ON Absolute value upper limit Absolute value lower limit Absolute value upper limit standby sequence ON Absolute value lower limit standby sequence ON LBA (only for alarm 1) Deviation lower limit standby sequence ON Deviation upper limit standby sequence ON Deviation upper/lower range Deviation upper limit Deviation upper/lower limit Deviation lower limit Alarm output function Positive alarm value (X) Negative alarm value (X) Setting PV Change Rate Alarm X ON OFF SP X ON OFF SP ON OFF SP X X ON OFF SP L H ON OFF SP X ON OFF SP X ON OFF SP X ON OFF 0 ON OFF X 0 X ON OFF 0 X ON OFF 0 ON OFF X 0 X ON OFF 0 X ON OFF 0 X ON OFF 0 X ON OFF 0 X ON OFF 0 ON OFF X 0 ON OFF X 0 ON OFF X 0 ON OFF X 0 L H ON OFF SP SP ON OFF X ON OFF X 0 1 0 2 3 4 5 6 7 8 9 SP absolute value upper limit SP absolute value lower limit 14 15 MV absolute value upper limit MV absolute value lower limit 16 17 10 11 12 13 SP X ON OFF ON OFF X 0 4 to 20mA 0 to 20mA 1 to 5V 0 to 5V 0 to 10V 25 26 27 28 29 Setting range Input type Input Pt100 JPt100 Thermocouple Infrared Thermosensor ES1B K J T E L U N R S B W PL II Setting 10 to 70°C 60 to 120°C 115 to 165°C 140 to 260°C 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 44.8�44.8 Sold Separately *USB-Serial Conversion Cable (E58-CIFQ2) In the pack: *Main unit *Instruction manual *Adapter (Y92F-49) * A Setup Tool port is provided on the upper of the product. Use this port to connect a personal computer to the product when using the Setup Tool. E58-CIFQ2 USB-Serial Conversion Cable is required to connect the personal computer to the product. (Do not use the product with the USB-Serial Conversion Cable left permanently connected.) Refer to the instruction manual provided with the USB-Serial Conversion Cable for details on connection methods. Input Type -200 to 850 -199.9 to 500.0 0.0 to 100.0 -199.9 to 500.0 0.0 to 100.0 -200 to 1300 -20.0 to 500.0 -100 to 850 -20.0 to 400.0 -200 to 400 -199.9 to 400.0 -200 to 600 -100 to 850 -200 to 400 -199.9 to 400.0 -200 to 1300 0 to 1700 0 to 1700 100 to 1800 0 to 2300 0 to 1300 0 to 90 0 to 120 0 to 165 0 to 260 -300 to 1500 -199.9 to 900.0 0.0 to 210.0 -199.9 to 900.0 0.0 to 210.0 -300 to 2300 0.0 to 900.0 -100 to 1500 0.0 to 750.0 -300 to 700 -199.9 to 700.0 -300 to 1100 -100 to 1500 -300 to 700 -199.9 to 700.0 -300 to 2300 0 to 3000 0 to 3000 300 to 3200 0 to 3200 0 to 2300 0 to 190 0 to 240 0 to 320 0 to 500 Platinum resistance thermometer Temperature inputs *The default is“5”. *s.err will be displayed when a platinum resistance thermometer is mistakenly connected while input type is not set for it. To clear the s.err display, correct the wiring and cycle the power supply. 2291439-6C(Side-A) 60 min. 45 45 +0.6 0 +0.6 0 +0.6 0 (48 x number of units - 2.5)+1.0 0 45 Installation Individual mounting (mm) Side-by-side mounting (mm) • Insert the main unit through the mounting hole in the panel (1 to 5 mm thickness). Insert the mounting brackets (supplied) into the fixing slots located on the top and bottom of the rear case. • Tighten the two mounting screws on the top and bottom of the adapter to keep them balanced, and finally tighten them to a torque of between 0.29 and 0.39 N·m. • When more than one machine is installed, make sure that the ambient temperature does not exceed the specified limit. °C °F CU1 48�48 Adapter (Y92F-49) L H ON OFF SP 4 58.6 76.8 14.2 44.8 58 48�48 Connections (The applicability of the electric terminals varies with the type of machine.) Do not connect anything to the terminals that are shaded gray. * When complying with EMC standards, the line connecting the sensor must be 30 m or less. If the cable length exceeds 30 m, compliance with EMC standards will not be possible. The is set for a K thermocouple (input type of 5) by default. If a different sensor is used, an input error ( s.err ) will occur. Check the setting of the Input Type parameter. Linear current output 0 to 20 mA DC Relay output (three terminals used) SPDT, 250 VAC, 3 A Voltage output (for driving SSR) 12 VDC, 21 mA Load: 500 � max. 4 to 20 mA DC Control output 1 (resistive load) Control output 1: RW CX A B B + - Relay outputs 250 VAC, 3 A (resistive load) Control output 1 Input power supply • 100 to 240 VAC • 24 VAC/DC (no polarity) Auxiliary output 1 Sensor (Temperature/Analog) Input - + V - mA + Auxiliary output 2 (Control output (cooling side)) Conformance to EN/IEC Standards This is a class A product. In residential areas it may cause radio interference, in which case the user may be required to take adequate measures to reduce interference. �� E5CC-U + P2CF-11 (93.8) Surface mounting Names of Parts on Front Panel • °C / °F : temperature unit The temperature unit is displayed when the displayed value is a temperature. Either C or F is displayed according to the set value of the temperature unit. • Mode key Press this key to change the contents of the display. Press this button for 1 s or longer for reverse scroll. • Press the O key and the M key together for at least 3 seconds to switch to protect level. • Level key Use this key to change levels: • Shift key (PF key) The default PF Setting parameter is for shifting the digit. This is a function key. When it is pressed, the function set for the PF Setting parameter will operate. • : Lit when Setting Change Protect is ON (disables the Up and Down Keys). • MANU: Lit during Manual Mode. Operation indicators • SUB1: Auxiliary output 1 indicator • SUB2: Auxiliary output 2 indicator • OUT1: Control output 1 indicator For a current output, lit except for a 0% output. • No.1 display Process value or set data type • No.2 display Set point, set data read-out value or changed input value • Up and Down keys Each press of U key increments or advances the values displayed on the No.2 display. Each press of D key decrements or returns the values displayed on the No.2 display. • TUNE: Flashing during ST(self-tuning). Lit during AT(auto-tuning). • STOP: Lit when “Run/Stop” is stopped during operation. During control stop, functions other than control output are valid. �� One relay output QX One voltage output (for driving SSR) One linear current output OUT1 Q OUT1 C OUT1 R Other functions Operation stopped. (Control/alarm are both stopped.) *5 Initial Setting Level Check the wiring before turning ON the power supply. POWER ON MV Monitor o (Heating) 0.0 MV Monitor c-o (Cooling) 0.0 Alarm Value al1l Lower Limit 1 *4 0 al-2 Alarm Value 2 *4 0 Alarm Value al2h Upper Limit 2 *4 0 Alarm Value al2l Lower Limit 2 *4 0 Input Type *3 Scaling Upper Limit (only when setting analog input) Scaling Lower Limit (only when setting analog input) Decimal Point (only when setting analog input) Temperature Unit SP Upper Limit SP Lower Limit PID•ON/OFF In ON/OFF control = onof In 2-PID control = pid Standard or Heating/Cooling Standard control = stnd Heating and cooling control = h-c Alarm 1 Type: Specified models only Control Period (Cooling) (Unit: Seconds) *Voltage output (for driving SSR): 2 ST (Self-Tuning) ST ON = on ST OFF = off Direct/Reverse Operation In Reverse operation (Heating) = or-r In Direct operation (Cooling) = or-d *3 *4 in-t 5 in-h 100 in-l 0 dp 0 d-u c sl-h 1300 sl-l -200 cntl onof s-hc stnd st on c-cp 20 orev or-r alt1 2 Move to Advanced Function Setting Level amov 0 alh1 Alarm 1 Hysteresis 0.2 alh2 Alarm 2 Hysteresis 0.2 Alarm 2 Type: alt2 Specified models only 2 at off Manual Reset Value Clears the offset during P or PD control. of-r 50.0 chys Hysteresis (Cooling) 1.0 PV Input Shift *8 ins 0.0 Derivative Time d (Unit: Seconds) 40 sp-0 SP 0 0 sp-1 SP 1 0 sp-3 SP 3 0 sp-4 SP 4 0 sp-5 SP 5 0 sp-6 SP 6 0 sp-7 SP 7 0 sp-2 SP 2 0 25 0 Process Value/Set Point s.err is displayed when connected sensor is different from input type. AT Execute / Cancel 100%AT Execute at-2 40%AT Execute at-1 c-db Dead Band 0.0 hys Hysteresis (Heating) 1.0 Control Output 1 o1st Signal 4-20 Integral Time (Cooling) (Unit: Seconds) c-i 233 Derivative Time (Cooling) (Unit: Seconds) c-d 40 Proportional Band c-p (Cooling) 8.0 °C= c °F= f *3 *4 Initial setting level enables users to specify their preferred operating conditions (input type, alarm type, control method, etc.) *3: Refer to the adjoining tables for details of input types and alarm types. *4: Applicable only to models with alarm functions. *5: Operation is stopped when moved to the initial setting level. (control/alarm are both stopped.) *6: The grayed-out setting items are not displayed for some models and some settings of other setting items. *7: The four numeric digits of the product code are displayed in the No. 2 display. The setting cannot be changed and there is nothing that you need to set. *8: Only the value set to the ins: Temperature Input Shift parameter is applied to the entire temperature input range. When the process value is 200°C, the process value is treated as 201.2°C after input shift if the input shift value is set to 1.2°C. The process value is treated as 198.8°C after input shift if the input shift value is set to -1.2°C. Hold O down for at least 1 second (No.1 display flashes, then the control stops.) Hold O down for at least 3 seconds Operation Level Set Point During SP Ramp sp-m 0 Multi-SP Set Point m-sp Selection 0 Auto/Manual Switch PID control only. a-m r-s RUN/STOP run al-1 Alarm Value 1 *4 0 When control start = run When control stop = stop Operation level should normally be used during operations. Hold O and M keys down for at least 1 second Hold O and M keys down for at least 3 seconds Press O (less than 1 second) Adjustment Level Adjustment level is for entering set values and shift values for control. M M M M M M M M M M M M M M M M M M M M M M M Alarm Value al1h Upper Limit 1 *4 0 M M M M M M M M M M M M M M M M Integral Time i (Unit: Seconds) 233 Proportional p Band 8.0 M M M M M M M M ol-h MV Upper Limit 100.0 sprt SP Ramp Set Value off ol-l MV Lower Limit 0.0 M M M M M (mm) Control output 1 E5CC 000 UM + - + - ptrn Program Pattern off M Extraction of Square Root Enable (Only when analog input is set) sqr off M prst Program Start rset sktr Soak Time Remain 0 M M Adjustment Level Displayed only once when entering Adjustment Level. *7 l.adj M PV input inrt Slope Coefficient 1.000 M M soak Soak Time 1 wt-b Wait Band off mv-s MV at Stop 0.0 mv-e MV at PV Error 0.0 M M M M SP Ramp Set Value (SP Ramp Fall Value) sprl same M MV Change orl Rate Limit 0.0 Extraction of Square sqrp Root Low-cut Point 0.0 M M M Auxiliary output 1,2 Operation / Adjustment Protect Restricts displaying and modifying menu items in Operation, Adjustment, and Manual Control Levels. oapt 0 Move to Protect Level Displayed only when a password is set. Restricts moving to Protect Level. Changed chgp Parameters Only off Parameter Mask Enable Displayed only when a parameter mask is set. pmsk on Initial Setting / Communication Protect Restricts movement to the Initial Setting, Communications Setting, and Advanced Function Setting Levels. icpt 1 Setting Change Protect Restricts changes to settings by operating the front panel keys. wtpt off pfpt off PF Key Protect Restricts PF key operation. Password to Move prlp to Protect Level 0 Protect Level Restricts which settings can be displayed or changed, and restricts change by key operation. M M M M M M M M pmov 0 30 0 to 50mV Control Period (Heating) (Unit: Seconds) *Voltage output (for driving SSR): 2 cp 20 Simple Transfer Output 1 o1th Upper Limit 100.0 M Simple Transfer Output 1 o1tl Lower Limit 0.0 M This product with sokect P2CF-11(E) or P3GA-11 gets the UL Listing Certification.It must be used with the sokect which mentioned above. Conformance to Safety Standard Reinforced insulation is provided between input power supply, relay outputs, and between other terminals. Do not allow temporary overvoltages on the primary circuit to exceed the following values. Check the power supply voltage to the Digital Controller. Short-term overvoltage: 1,200 V + (Power supply voltage) Long-term overvoltage: 250 V + (Power supply voltage) Always externally connect the recommended fuse that is specified in the Instruction Manual before you use the Digital Controller. Analog Input • If you input an analog voltage or current, set the Input Type parameter to the correct input type. • Do not use the Digital Controller to measure a circuit with Measurement Category II, III, or IV. • Do not use the Digital Controller to measure an energized circuit to which a voltage that exceeds 30 Vms or 60 VDC is applied. The protection provided by the Digital Controller may be impaired if the Digital Controller is used in a manner that is not specified by the manufacturer. Conformance to Safety Standards

©All Rights Reserved

�� ins�� JPN �� [[[[��]]]]�� s.err�� e111�� e333�� s.err�� s.err�� O�� O�� 25 0 �� sp-m �� 0 �� a-m al1l �� 0 al-2 �� 0 al2h �� 0 al2l �� 0 25 0 �� s.err M M M M �� o �� 0.0 �� c-o �� 0.0 M M M �� m-sp �� 0 M M ��run ��stop r-s �� run al-1 �� 0 M M al1h �� 0 M M �� oapt 0 �� chgp �� off �� pmsk on �� icpt 1 �� wtpt off pfpt off �� O�M�� O�M�� prlp �� 0 M M M M M M M M O�� onof ��pid �� stnd �� h-c �� c ��f �� on ��off �� or-r ��or-d �� in-t 5 in-h 100 in-l 0 dp 0 d-u c sl-h 1300 sl-l -200 cntl onof s-hc stnd st on c-cp 20 orev or-r alt1 2 �� amov �� 0 alh1 �� 0.2 alh2 �� 0.2 �� alt2 2 �� o1st 4-20 M M M M M M M M M M M M M M M M M M �� sqr off M prst �� rset sktr �� 0 M M �� at off ol-h �� 100.0 sprt �� off �� sprl same ins �� 0.0 �� inrt 1.000 ol-l �� 0.0 orl �� 0.0 sqrp �� 0.0 sp-0 �� 0 sp-1 �� 0 sp-4 �� 0 sp-5 �� 0 sp-6 �� 0 sp-7 �� 0 sp-2 �� 0 p �� 8.0 M chys �� 1.0 hys �� 1.0 M M soak �� 1 wt-b �� off M M mv-s �� 0.0 mv-e �� 0.0 M M M M M M M M M M M M M M �� i 233 �� d 40 �� c-i 233 �� c-d 40 c-p �� 8.0 M M M M c-db �� 0.0 M �� of-r 50.0 M M M M M sp-3 �� 0 M M M �� at-2 ��at-1 �� l.adj pmov 0 �� cp 20 M o1th �� 100.0 M o1tl �� 0.0 M �� stop�� C��F�� O��M�� U�� D�� 44.8 �48 �� 4 58.6 76.8 14.2 44.8 58 �48 �� A B B + - �� • • �� - + V - mA + �� s.err�� E5CC-U + P2CF-11 (93.8) �� RW CX �� QX + - �� Q �� C �� R ptrn �� off M �� + - �� 安全規格対応について �� 2291439-6C(Side-B)

Other Controller Manuals

Omron E5CC-U Instruction Manual

Text of the manual

Indicates a potentially hazardous situation which, if

©All Rights Reserved

Other Controller Manuals

Surefire BMS-300

Aqua Computer farbwerk 360

Excelitas Technologies OmniCure LX500

Motorola 3200