Mikado Logo 600 SX Manual 

LOGO 600 SX © Mikado Model Helicopters GmbH 2015, V1.0029 Manual Mikado Model Helicopters GmbH • Friedrich-Klausing-Straße 2 • 14469 Potsdam • Germany phone +49 (0)331 23749-0 • fax +49 (0)331 23749-11 • www.mikado-heli.de Modellbau Lindinger GmbH e-Mail: [email protected] www.lindinger.at

Index OPERATING YOUR MODEL SAFELY Operate the helicopter in spacious areas with no people nearby. !Warning: Do NOT operate the helicopter in the fol- lowing places and situations (or else you risk severe accidents): • in places where children gather or people pass through • in residential areas and parks • indoors and in limited space • in windy weather or when there is any rain, snow, fog or other precipitation If you do not observe these instructions you may be held reliable for personal injury or property damage! Always check the R/C system prior to operating your helicopter. When the R/C system batteries get weaker, the operational range of the R/C system decreases. Note that you may lose control of your model when operating it under such conditions. Keep in mind that other people around you might also be operating a R/C model. Never use a frequency which someone else is using at the same time. Radio signals will be mixed and you will lose control of your model. If the model shows irregular behavior, bring the model to a halt immediately. Turn off all power switches and disconnect the batteries. Investigate the reason and fi x the problem. Do not operate the model again as long as the problem is not solved, as this may lead to further trouble and unforeseen accidents. ! Warning: In order to prevent accidents and personal injury, be sure to observe the following: Before fl ying the helicopter, ensure that all screws are tightened. A single loose screw may cause a major accident. Replace all broken or defective parts with new ones, as damaged parts lead to crashes. Never approach a spinning rotor. Keep at least 10 me- ters/yards away from a spinning rotor blades. Do not touch the motor immediately after use. It may be hot enough to cause burns. Perform all necessary maintenance. PRIOR TO ADJUSTING AND OPERATING YOUR MO- DEL, OBSERVE THE FOLLOWING !Warning: Operate the helicopter only outdoors and out of people’s reach as the main rotor operates at high rpm! ! Warning: While adjusting, stand at least 10 meters/ yards away from the helicopter! Novice R/C helicopter pilots should always seek advice from experienced pilots to obtain hints with assem- bly and for pre-fl ight adjustments. Note that a badly assembled or insuffi ciently adjusted helicopter is a safety hazard! In the beginning, novice R/C helicopter pilots should always be assisted by an experienced pilot and never fl y alone! Tools for Assembly & R/C Equipment Safety Instructions Safety Instructions . . . . . . . . . . . . . . . . . 2 Tools for Assembly & R/C Equipment . . . . . . . 2 1 Mainframe . . . . . . . . . . . . . . . . . . . . . 3 2 Tail Rotor . . . . . . . . . . . . . . . . . . . . . 4 3 Tail Boom . . . . . . . . . . . . . . . . . . . . . 5 4 Main Gear & Tail Boom Assembly . . . . . . . . 6 5 V-Bar Rotor Head . . . . . . . . . . . . . . . . . 7 6 Servo Installation . . . . . . . . . . . . . . . . . 8 7 Mounting the Motor . . . . . . . . . . . . . . . . 9 8 Canopy Mounting . . . . . . . . . . . . . . . . . 9 9 Radio and Battery . . . . . . . . . . . . . . . 10 10 Overview Chassis . . . . . . . . . . . . . . . 11 11 Overview Tail Rotor . . . . . . . . . . . . . . 12 12 Overview V-Bar Head . . . . . . . . . . . . . 13 Manual Mikado LOGO 600 SX Note: There is no bag 4 and 10. The bags are numbered 1 to 12, with the exception of 4 and 10. Max. rotorhead rpm LOGO SX 600: 2100 Max. collective range: +/- 12° Max. Rotor blade size: 600 mm - 620 mm Max. LiPo Akku size: 10S 5000 mAh Max. LiPo Akku size: 12S 3300 mAh LOGO 600 SX is not recommended for novices. This heli- copter is a complex system. Basic knowledge of the func- tion of a model helicopter is required to build and operate the LOGO 600 SX. 5 Minute Epoxy 5 Minute Epoxy Radio with Heli-Software Motor + Speed Controller (check the Mika- do webpages for recommended motors) Alle shown products are examples. You may use different brands. Scissors Rubber Hammer Screwdrivers (plus and minus) Hex Wrenches 1.5/2.0/2.5/3.0 mm (.055/.079/.098/.118 in) Ball link pliers Threadlock circlips pliers Grease Pitch Gauge V-Bar Battery Modellbau Lindinger GmbH e-Mail: [email protected] www.lindinger.at

3 2 1 3x7x3 3x17 17x M2,5 1x SW5x59 3 x 5x49 2x 3x17 4x 3x5x2,5 4x M3x20 2x M3x16 2x 2,2x6 4x M2,5x8 9 x M2,5x10 4x M2,5x16 4x M2,5x12 2x M3x20 2x M3 10x19x5 M2,5x16 (4x) M2,5x12 M2,5x12 M2,5x10 M2,5x8 M2,5 Stop M3x20 M3x16 M3x20 M3x20 Ø5x49 SW Ø5x59 M3x16 M3x20 2,2x6 M3 Stop M3 Stop Using the rod M2.5x60 from bag 7, position all 14 nylon nuts in the right side frame. Before you combine the two sides of the main frame, attach the two belt tensioners (#4089, bag 6). 1 Mainframe Bag 1 All parts shown in the boxes are displayed in real size. After assembling the chassis. please move the battery plate in to the frame. You should position the motor pinion on the motor shaft, before you mount the motor plate. You may also mount the motor pinion at a later stage, but the process will be more cumber- some. For reading on how to mount the motor pinion, please fl ip to page 9. Bag 1 raised head raised head tapping screw Modellbau Lindinger GmbH e-Mail: [email protected] www.lindinger.at

LOGO 600SX 2 Beutel 5 2 M3x14 M2x8 3x6x2,5 3x5x0,5 3x5x5 M3 Stopp (5x) M2,5x6 3 M3x16 5x8x3 6x8x0,5 M3 Stopp 1x 3x5x5 1x M2x8 1x Kugel/ball/Rotule Ø4,8x2 1x 3x5x0,5 1x M3x14 2x 3x6x2,5 1 1 a b c d 2 3 Kugel/ball/Rotule Ø4,8x2 3x8 5x13x4 M3x35 (5x) M3x8 5x7x2,3 3x10x7 2x 6x8x0,5 2x M3x8 4x 5x8x3 2x M3x16 2x 4x8x3,5 2x M3 1x M3x3 1 5x M3 1x M2,5x6 1x 5x27 2x M3x8 5x M3x35 M3 Stop (5x) 2x 3x5x10 1x 3x10x7 2x 5x13x4 2x 5x7x2,3 2 Tail Rotor Apply grease on bearing larger inner Ø smaller inner Ø Apply Loctite only in the threaded section inside the tail rotor hub! Glue ball bearings using 5min. Epoxy Bag 5 Bag 5 Bag 5 Modellbau Lindinger GmbH e-Mail: [email protected] www.lindinger.at

2x M3 1x M2x6 1x M2 Stop 2x M3x16 4x Kugel/ball/Rotule Ø6x3 2x M3x40 2x 3mm 2x M3x40 M2x6 M2 M3x3 M3x16 (2x) Ø4x680 mm Ø5x520 mm M3 Stop 3 Tail Boom Bag 6 Bag 5 Bag 6 + 11 Bag 6 + 11 Ball Ø6 mm Ball Ø6 mm Attach the ball links so that the engraved number is on the outer surface pointing towards you. 5 Min. Epoxy 5 Min. Epoxy Bag 6 • Bag 11 Modellbau Lindinger GmbH e-Mail: [email protected] www.lindinger.at

5 4x M3 4x M3x10 4x M3x3 2x 10x16x0,5 1x 3x16 1x M2,5x8 2 1 4 3 (7x) 5 1x 2,2x6 10x16x0,5 M3x8 M3x10 M3x10 M3 Stopp (4) M3x20 4 Main Gear & Tail Boom Assembly Bag 2 • Bag 3 • Bag 8 Bag 2 Swashplate bag 3 Bag 8 Attach the tail boom with a screw 2.2x6 Tighten the pivot bolts very carefully. Do not overtighten them, as they will break off. •To remove the battery, rotate locking mechanism until it locks. •After inserting a battery, rotate back to secure the battery plate in place. Tighten tooth belt: Pull tail rotor backwards and tighten screws Carefully push in ... Do not damage the tail boom holders. For wider batteries, you may enlarge this cut-out. Modellbau Lindinger GmbH e-Mail: [email protected] www.lindinger.at

1x M3x47 2x 3x5x1,2 4x M2,5x10 12x 2,2x13 2x M2x10 1x M2x12 4x 9x M2 3x M2,5x35 2,2x13 (4x) 23 mm (4x) 2,2x13 (4x) M2,5x10 (4x) 1 2 3 4 5 6 7 8 9 5 Servo Installation Bag 1 • Bag 9 Bag 9 Bag 1 Bag 9 Bag 1 Apply a small amount of oil to the rotor shaft. If you are installing Futaba servos, add the distance plate for the two aileron servos. LOGO Rotor Head (V-Stabi, f ybarless head) 16 mm 16 mm 16 mm 14-16mm Attach the ball links so that the engra- ved number is on the outer surface pointing towards you. Aileron left Aileron right Elevator Rudder Modellbau Lindinger GmbH e-Mail: [email protected] www.lindinger.at

1x M3x6 2x 8x16x5 4x 11,5x15,8x0,3 M3x20 2x M3x35 2x M5x12 2x M4x35 2x 5x15x1 2x M3 Stop 2x M4 Stop 2x Ø4,8x3 2x 3x12 4x 3x7x3 4x 3x6x2,5 2x 3x5x2 2x M3x20 1 2 3 4 7 8 5 6 M3x6 M3 Stopp M3x20 3x12 28 mm M3x35 3x7x3 3x5x2 3x6x2,5 M3x20 3x5x0,5 7x5 2x M5x12 M5x12 8x16x5 11,5x15,8x0,3 6x 7x5 O-Ring 2x 11,5x15,8x0,3 8x15x2,6 5x15x1 4x 2x 4x 4x 8x16x5 M2,5x40 8x15x2,6 6 V-Bar Rotor Head LOGO 600SX Bag 7 Bag 7 Large inner diameter Small inner diameter Apply grease to bearing. Mounting direction is not critical. Please supply silicon oil or grease on o-rings and spindle shaft! Center the spindle shaft exactly! After mounting, the blade holders will move a little bit tightly at fi rst. Modellbau Lindinger GmbH e-Mail: [email protected] www.lindinger.at

M4x32 2x M3x20 2x 2x 4x M3x8 1x 6x9x0,3 2x M4x32 3x M3x6 1 2 4x 10x16x0,5 6x9x0,2 10x16x0,5 10x16x0,5 10x16x0,5 5x10x1 7 Mounting the Motor 8 Mounting the Canopy Bag 1,2 Bag 1 Installation of the Motor Pinion Screw the motor pinion onto the motor shaft, making sure that it can still be moved. Now mount the motor on the motor plate and move the pinion so it is aligned well with the main gear. As visual help for aligning the pinion you may use the small ridge which separates the two parts of the pinion. When the pinion is aligned correctly it will easily engage with the main gear. If the pinion does not engage with the main gear, it is not correctly aligned. After the pinion is correctly aligned, take the motor out of the mainframe and tighten the set screw. Gear Backlash Move the motor with the pinion until it is limited by the gear. Tighten one of the M4x32 screws slightly. You must still be able to swivel the motor around its own axis. In this way you can easily deter- mine the correct distance between the main gear and the pinion. There should be no (!) gear backlash. At the same time, the motor should not (!) exert any pressure onto the running surface of the main gear. After you have determined the correct distance, tighten the second M4x32 screw. Bag 2 Bag 1 Please mount the motor, motor plate, pinion and counterbearing as illustrated in the above picture. When positioning the pinion, please ensure that it sits exactly on the ball bearing of the counterbearing with only one shim (6.9x0.2) inbetween. Also make sure that the M4 set screw sits on the flattened area of the motor shaft. For mounting the new motor counterbearing with ro- torshaft suport, please follow these steps: First, mount the main gear, the rotor shaft assembly and all shims. Secure assembly with the 10 mm c-clip (Picture 2). The main gear will have 0.5 mm axial play. This is normal and will facili- tate the mounting and positioning of the pinion later on. Now mount the motor and the counterbearing. Once the motor position is set (please ensure correct gear back- lash!), please screw the rotorshaft support onto the coun- terbearing, using the three M3x6 screws. Bag 9 Modellbau Lindinger GmbH e-Mail: [email protected] www.lindinger.at

1 2 3 4 5 7 6 9 Radio and Battery Battery: Attach the battery with the 3 velcro straps. Mount the battery in a position where the center of gravity is met with the battery holder installed. To adjust, leave the heli unpowered. The exact center position of the servo arm will be determined in the trim fl ight. Position of servo arms for the aileron servos when sticks are centered (0 deg. Pitch) Velcro Strap Velcro (adhesive) Position for Mini V-Bar Position for V-Bar gyro speed controller Modellbau Lindinger GmbH e-Mail: [email protected] www.lindinger.at

2364 (550) 4192 4064 4191 2010 4059 1915 2010 (10x16x0,5) 2009 (10x16x0,2) 4067 1344 4094 M07-153 4183 M1-106, 11mm 4621 M1-106, 13mm 4622 (6mm Motorshaft) 4714 (5mm Motorshaft) 4290 black LOGO 500/600/690 4288 white LOGO 500/600/690 4311 white 2775 black 1920 1954 1941 4913 2074 1958 4917 4099 4914 4912 4919 1953 4915 4236 2385 4089 4103 930 1329 1938 4102 2071 (14x) 1329 2383 4091 4072 (20mm) 4713 (22mm) 4651 4930 1974 4868 (600/690) 10 Overview Chassis Modellbau Lindinger GmbH e-Mail: [email protected] www.lindinger.at

4634 4235 3077 2447 1961 4273 4626 4627 4625 4107 04074 2466 4137 4098 LOGO 600 4354 LOGO 600 SE 4073 LOGO 600 4355 LOGO 600 SE 4081 (730XL LOGO 600) 4325 (770XL LOGO 600 SE) 4097 (SET) LOGO 600 4354 (SET) LOGO 600 SE 4145 4630 4630 2462 727 2074 1956 4344 EDGE 95 4345 EDGE 105 3069 4615 2074 4096 4634 11 Overview Tail Rotor Modellbau Lindinger GmbH e-Mail: [email protected] www.lindinger.at

Construction & Rendering: Mehran Mahinpour Tirooni, André Doil • Layout & Realisation: CDT, André Doil www.mikado-heli.de 930 2330 1980 1974 2076 840 4708 954 915 845 04050 1574 4617 1961 1565 1586 (60mm) 1579 (65mm) 4049 4133 4618 4619 (for mainshaft #4620) 4631 (for main shaft #4075) 1588 (40mm) 2074 12 Overview V-Bar Head Modellbau Lindinger GmbH e-Mail: [email protected] www.lindinger.at