Datalogic Joya Operation & User’s Manual

40012 Lippo di Calderara di Reno Bologna - Italy Telephone: (+39) 051-3147011 Fax: (+39) 051-3147205 ©2016 Datalogic S.r.l. An Unpublished Work - All rights reserved. No part of the contents of this doc- umentation or the procedures described therein may be reproduced or trans- mitted in any form or by any means without prior written permission of Datalogic S.r.l. or its subsidiaries or affiliates. Owners of Datalogic products are hereby granted a non-exclusive, revocable license to reproduce and trans- mit this documentation for the purchaser's own internal business purposes. Purchaser shall not remove or alter any proprietary notices, including copy- right notices, contained in this documentation and shall ensure that all notices appear on any reproductions of the documentation. Should future revisions of this manual be published, you can acquire printed versions by contacting your Datalogic representative. Electronic versions may either be downloadable from the Datalogic website (www.datalogic.com) or provided on appropriate media. If you visit our website and would like to make comments or suggestions about this or other Datalogic publications, please let us know via the "Contact Datalogic" page. Disclaimer Datalogic has taken reasonable measures to provide information in this man- ual that is complete and accurate, however, Datalogic reserves the right to change any specification at any time without prior notice. Datalogic and the Datalogic logo are registered trademarks of Datalogic S.p.A. in many countries, including the U.S.A. and the E.U. JOYA is a trademark of Datalogic S.p.A. or of Datalogic Group companies, reg- istered in many countries, including the U.S. and the E.U. All other brand and product names may be trademarks of their respective owners. Patents Patent. See www.patents.datalogic.com for patent list.

Introduction ....................................................................... 1 Conventions ..................................................................................1 Product Presentation ..................................................................2 Available Models ..........................................................................3 Out of the Box ...............................................................................5 General View .................................................................................6 Front View ........................................................................................ 6 Back View ......................................................................................... 7 Top View ........................................................................................... 8 Side View .......................................................................................... 8 Accessories ...................................................................................9 Battery............................................................................. 11 Install the Battery ..................................................................... 11 Charge the Battery .................................................................... 13 Fast Charge .................................................................................... 13 Standard Charge ............................................................................ 14 Battery Safety Guidelines ......................................................... 17 Use and Functioning...................................................... 21 Getting Started .......................................................................... 21 Taskbar ....................................................................................... 23 Touch Gestures .......................................................................... 24 Data Capture .............................................................................. 25 Imager Data Capture ..................................................................... 25 Resetting the JOYA TOUCH ....................................................... 28 Warm Boot ..................................................................................... 28 Cold Boot ......................................................................................... 29

Control Panel ..............................................................................31 Data Capture Configuration .......................................................... 32 DL Buttons ..................................................................................... 50 Persistent Registry ....................................................................... 52 Wireless Communications ............................................................ 54 Audio Settings ................................................................................ 62 Connecting to other Computers ...............................................65 Windows Mobile® Device Center ................................................. 65 Datalogic Firmware Utility ........................................................66 Retrieving a Firmware Image Update ......................................... 66 Installing DFU on the Host PC ...................................................... 67 Updating the Firmware ................................................................. 68 Datalogic Desktop Utility ...........................................................69 Administrative Options (Admin tab) ............................................ 70 Locked Web Browser Options (LockedWeb tab) ........................ 75 Status Icons Options (Status Tab) ............................................... 77 Windows Control ........................................................................... 78 AppSelector Options (AppSelect tab) ........................................... 80 Locked Web Browser .................................................................83 FlashDisk Directory File Management ....................................84 Connections ..................................................................... 87 USB Connection ..........................................................................87 USB Direct Connection .................................................................. 87 Wi-Fi Connection ........................................................................88 Bluetooth® Serial Connection ...................................................90 Wireless and Radio Frequencies Warnings ............................92 Technical Features.......................................................... 95 Technical Data ............................................................................95 Decode Distances .......................................................................99 Test Codes..................................................................... 101 Maintenance................................................................. 109

Ergonomic Recommendations .............................................. 110 Safety and Regulatory Information............................ 111 General Safety Rules ............................................................... 111 Power Supply ........................................................................... 112 Laser Safety ............................................................................. 113 LED Class .................................................................................. 121 Marking and European Economic Area (EEA) ...................... 121 Statement of Compliance ....................................................... 122 Radio Technologies and Frequency Bands ........................... 125 Information for the User .............................................................126 FCC/IC Labeling ....................................................................... 127 FCC Compliance ....................................................................... 127 ISED Compliance ...................................................................... 129 Radiofrequency Radiation Exposure Information ............... 131 WEEE Compliance ................................................................... 132 Support.......................................................................... 135 Reference Documentation ..................................................... 135 Warranty Terms and Conditions ........................................... 135 Glossary......................................................................... 137

‘Device’ and 'JOYA TOUCH' refer to the JOYA TOUCH. ‘Dock’ refers to the JOYA TOUCH 3-Slot Cradle. The label artworks may be only a draft. Refer to the product labels for more precise information.

compact 7 powered mobile computer, available in two form factors. This compact, lightweight, and versatile device, combines fully integrated automatic data capture (2D bar code), a wireless charging system and wireless communication capabilities, supporting nearly any application. The Datalogic JOYA TOUCH system architecture is based on the blend of Intel X-Scale series processors coupled with the Windows Embedded Compact operating system and it was developed to meet the most demanding customer needs. A huge quantity of on-board memory is available. It enables the user to adapt the terminal for any specific need. Thanks to its great ergonomics and the state of the art architecture, the Datalogic JOYA TOUCH is the right answer to enhance your business opportunities.

depending on the features it is equipped with. All options are listed below: • p/n 911350010 JOYA TOUCH Plus Handheld, FWVGA Full Touch color display 4.3” in diagonal, white-illumination 2D imager engine, Green Spot, radio 802.11 A/B/G/N, 512MB RAM, 1GB Flash + 4GB SD, Bluetooth Dual Mode V.4, Windows Embedded Compact 7 with dedicated SDK for developing 3rd party applications. Wavelink Avalanche® device management preloaded. Gray/Blue colors combination (upper case / battery cover). This model is available also in other colors combinations (indicated colors represent front housing/battery cover): - 911350014 Grey/Grey - 911350015 Grey/Red - 911350020 Blue/Yellow - 911350021 Orange/Orange - 911350022 Green/Green • p/n 911350011 JOYA TOUCH Plus Pistol Grip, FWVGA Full Touch color display 4.3” in diagonal, white-illumination 2D imager engine, Green Spot, radio 802.11 A/B/G/N, 512MB RAM, 1GB Flash + 4GB SD, Bluetooth Dual Mode V.4, Windows Embedded Compact 7 with dedicated SDK for developing 3rd party applications. Wavelink Avalanche® device management preloaded. Grey/Blue/Blue colors combination (upper case / trigger / battery cover).

colors represent front housing/battery cover/trigger): - 911350012 Grey/Grey/Blue - 911350013 Grey/Red/Red - 911350016 Yellow/Yellow/Yellow - 911350017 Red/Grey/Grey - 911350018 Grey/Orange/Orange - 911350019 Grey/Green/Green • p/n 911350023. JOYA TOUCH Basic Handheld, FWVGA Full Touch color display 4.3” in diagonal, white-illumination 2D imager engine, Green Spot, radio 802.11 A/B/G/N, 512MB RAM, 512GB Flash, Windows Embedded Compact 7 with dedicated SDK for developing 3rd party applications. Wavelink Avalanche® device management preloaded. Gray/Red colors combination (upper case / battery cover). • p/n 911350024 JOYA TOUCH Basic Pistol Grip, FWVGA Full Touch color display 4.3” in diagonal, white-illumination 2D imager engine, Green Spot, radio 802.11 A/B/G/N, 512MB RAM, 512GB Flash, Windows Embedded Compact 7 with dedicated SDK for developing 3rd party applications. Wavelink Avalanche® device management preloaded. Grey/Red/Red colors combination (upper case / trigger / battery cover). For further details about the Datalogic JOYA TOUCH models refer to the web site: www.datalogic.com.

The JOYA TOUCH package contains: • JOYA TOUCH (device) • Rechargeable battery • Quick Start Guide • Safety & Regulatory Addendum • EULA Addendum Remove all the components from their packaging; check their integrity and compare them with all the packing documents. CAUTION Keep the original packaging for use when sending products to the technical assistance center. Damage caused by improper packaging is not covered under the warranty.

Scan Trigger Micro USB Port Handheld Models Pistol Grip Models

Cradle Accessories 91ACC0045 JOYA TOUCH Cradle Unlock Key (5 PCS) 91ACC0048 JOYA TOUCH 3-Slot Cradle Power Supply. Line Cord required (max 2 cradles on standard charge, max 1 cradle on fast charge per power supply) 91ACC0049 JOYA TOUCH Cradle Power Jumper (5 PCS) 91ACC0050 JOYA TOUCH 3-Slot Cradle Wall Bracket 91ACC0051 Blue Kit to convert Plus Handheld to a Pistol Grip 91ACC0052 Blue Kit to convert Plus Pistol Grip to a Handheld 91ACC0053 Blue Kit to convert Basic Handheld to a Pistol Grip 91ACC0054 Blue Kit to convert Basic Pistol Grip to a Handheld Batteries 91ACC0055 JOYA TOUCH Replacement Battery 3.75V 3030 mAh Various 91ACC0047 JOYA TOUCH Trolley Holder (60pieces) NOTE Use only Datalogic-approved power supply and cables. Use of an alternative power supply will invalidate any approval given to this device and may be dangerous.

To install the battery pack, follow the steps below: 1. Unscrew the battery cover and remove it: 2. Connect the battery contacts to the battery clip located in the battery slot: Handheld Models Pistol Grip Models Handheld Models Pistol Grip Models

below: 4. Insert the battery cover and fix the screws: NOTE Required torque of the screws is 35 cNm. Handheld Models Pistol Grip Models Handheld Models Pistol Grip Models

The JOYA TOUCH battery pack is not initially fully charged. After installing the battery, charge it with the 3-slot cradle. The device needs to be inserted head down into the cradle. There are two options to connect the cradle to the power supply: fast charge and standard charge. Fast Charge The fast charge connection allows to power one cradle with one power supply. Plug the power supply cable into the power connector on the back of the cradle, then plug the power supply into the AC/DC plug using a Datalogic power cable. Please see below an example of how to insert the power supply cable through the wall mounting metal bracket: NOTE Charge the battery for a minimum of 7 hours in standard charge and 3 hours in fast charge. High Visibility High Density

one power supply. To connect a second cradle use the JOYA TOUCH Cradle Power Jumper, available as optional accessory (P/N 91ACC0049). 1. Connect the first cradle to the second cradle using the power jumper. 2. Connect the power supply to the first cradle. 3. Plug the power supply into the AC/DC plug using a Datalogic power cable. By default, the main battery pack is disconnected at the factory to avoid damage due to excessive draining. Rechargeable battery pack is less than half of full charge when delivered. NOTE For further information on the JOYA TOUCH 3-Slot Cradle, refer to the JOYA TOUCH 3-Slot Cradle Quick Start Guide, included in the cradle’s box, and to the JOYA TOUCH 3-Slot Cradle Installation Guide, downloadable from our website www.datalogic.com.

as the frequency of bar code scanning, RF usage, battery life, storage, environmental conditions, etc. Close to the limits of the working temperature, some battery performance degradation may occur. The JOYA TOUCH should be charged at an ambient temperature between 0 - 35º C (32 to 95ºF) to achieve the maximum charging rate. Never charge the device battery in a closed space where excessive heat can build up. As a safety precaution, the battery may stop charging to avoid overheating. The JOYA TOUCH may get warm during charging; this is normal and does not mean a malfunction. Even if the storage temperature range is wider, it is recommended to store the terminal and the batteries at environmental temperature, in order to achieve the longest battery life. CAUTION Avoid storing batteries for long periods in a state of full charge or very low charge. We recommend charging the battery pack every two to three months to keep its charge at a moderate level to maximize battery life. Annual replacement of rechargeable battery pack avoids possible risks or abnormalities and ensures maximum performance.

expose to high temperature. Risk of fire and explosion. Use specified charger only. Risk of explosion if the battery is replaced by an incorrect type. Dispose of batteries as required by local authorities. WARNING Use only Datalogic approved batteries and accessories for battery charging. Risk of explosion if battery is replaced by an incorrect type. Dispose of used batteries according to the instructions. Il y a risque d’explosion si la batterie est remplacée par une batterie de type incorrect. Mettre au rebut les batteris usagées confor mément aux instructions.

WARNING Installing, charging and/or any other action should be done by authorized personnel and following this manual. The battery pack may get hot, explode, ignite, and/or cause serious injury if exposed to abusive conditions. If the battery pack is replaced with an improper type, there is risk of explosion. Do not place the battery pack in or near a fire or other heat source; do not place the battery pack in direct sunlight, or use or store the battery pack inside unventilated areas in hot weather; do not place the battery pack in microwave ovens, in clothes dryers, in high pressure containers, on induction cook surfaces or similar devices. Doing so may cause the battery pack to generate heat, explode or ignite. Using the battery pack in this manner may also result in a loss of performance and a shortened life expectancy. To power the cradle, use only a Datalogic approved power supply. The use of an alternative power supply will void the product warranty, may cause product damage and may cause heat, an explosion, or fire. The area in which the units are charged should be clear of debris and combustible materials or chemicals. Do not use the battery pack of this terminal to power devices other than this mobile computer.

while using, charging or storing the battery pack, the battery pack emits an unusual smell, feels hot, changes color or shape, or appears abnormal in any other way. Do not short-circuit the battery pack contacts connecting the positive terminal and negative terminal. This might happen, for example, when you carry a spare battery pack in your pocket or purse; accidental short–circuiting can occur when a metallic object such as a coin, clip, or pen causes direct connection of the contacts of the battery pack (these look like metal strips on the battery pack). Short– circuiting the terminals may damage the battery pack or the connecting object. Do not apply voltages to the battery pack contacts. Do not pierce the battery pack with nails, strike it with a hammer, step on it or otherwise subject it to strong impacts, pressures, or shocks. Do not disassemble or modify (i.e. bend, crush or deform) the battery pack. The battery pack contains safety and protection devices, which, if damaged, may cause the battery pack to generate heat, explode or ignite. In case of leakage of liquid from the battery, avoid contact with liquid the skin or eyes. If the contact occurs, immediately wash the affected area with water and consult a doctor. Do not solder directly onto the battery pack. Do not expose the battery pack to liquids.

or the battery is dropped, especially on a hard surface, you should take it to the nearest Authorised Repair Centre for inspection before continuing to use it. If your device stops working for any reason, do not use its battery on other electronic devices without a prior check and approval by an Authorised Repair Centre. Do not replace the battery pack when the device is turned on. Do not remove or damage the battery pack’s label. Do not use the battery pack if it is damaged in any part. Battery pack usage by children should be supervised. Collect and recycle waste batteries separately from the device in compliance with European Directive 2006/66/EC, 2011/65, 2002/96/EC and subsequent modifications, with US and China regulatory laws and regulations about the environment.

The use of the JOYA TOUCH depends on the application software loaded. However, there are several parameters that can be set and utilities that can be used to perform some basic functions such as data capture, communications, file management, etc. Furthermore, Avalanche Enabler is a major utility embedded in the software provided from factory. Getting Started The JOYA TOUCH turns on when a charged battery pack is inserted.

22 JOYA™ TOUCH The mobile computer goes into power-off (low power with display and keyboard backlight off), when it is no longer used for more than a programmable timeout, which is defined in the POWER applet of the Control Panel. In this mode it can be awakened (resuming operation) pressing the Home key. NOTE The mobile computer can also be awakened or turned off by the application program.

User’s Manual 23 Taskbar The Taskbar provides information about the time, the battery level, the keyboard function, and the decoding status. ICON DESCRIPTION Time Icons It displays the time. Radio Status Icons It indicates if the radio is connected or not with an Access Point. Network Status Icons It displays whether you are connected or not to Wi-Fi or Bluetooth Personal Area Network. ActiveSync connection icon is displayed when connected to ActiveSync or Windows Mobile Device Center either by USB or Bluetooth. Double-tap it to open a status dialog that will let you disconnect the ActiveSync session without physically disconnecting the device from the PC. It is the only way to disconnect a Bluetooth ActiveSync connection.

24 JOYA™ TOUCH Touch Gestures Double Tap Touch the screen twice to open items and select options. Drag Touch and slide your finger on screen to select text and images. Drag in a list to select multiple items. Tap-and-hold Tap and hold your finger on an item to see a list of actions available for that item. On the pop-up menu that appears, tap the action you want to perform. CAUTION To prevent damage to the screen, do not use sharp devices or any device other than your finger or a touch screen stylus. In harsh applications, use of screen protectors should be taken into consideration, in order to extend the touch screen operating life. Do not apply not necessary high pressures on the screen. For applications where an intensive use of the touch screen is foreseen, please consider that touch screen components are subject to progressive wear.

User’s Manual 25 Data Capture To capture data, first of all double-tap Control Panel > Decoding and open the applet. Imager Data Capture The imager uses digital camera technology to take a digital picture of a bar code, the image is stored in memory and software decoding algorithms are executed to extract the data from the image. The omnidirectional scanning does not require that the operator orient the bar code to align with the scan pattern. To scan a bar code symbol: 1. Point the scan window at the bar code.

26 JOYA™ TOUCH 2. Press the home key. The imager projects a laser aiming pattern similar to those used on cameras. The aiming pattern is used to position the bar code or object within the field of view. 3. Center the symbol in any orientation within the aiming pattern. Ensure the entire symbol is within the rectangular area formed by the brackets in the aiming pattern, then either wait for the timeout or release the home key to capture the image. A red beam illuminates the symbol, which is captured and decoded. Linear Bar Code 2D Matrix Symbol

User’s Manual 27 If the scan has been successful: • If enabled, the good read beep plays. • If enabled, the GreenSpot projects a green spot onto the bar code image. • If enabled, a pop-up window will report the data and the symbology of the scanned bar code (See “Data Capture Configuration” on page -32). The field of view changes its size as you move the reader closer or farther away from the bar code. The aiming pattern is smaller when the imager is closer to the bar code and larger when it is farther from the bar codebar code. Scan symbols with smaller bars or elements (mil size) closer to the unit and those with larger bars or elements (mil size) farther from the unit. Hold the JOYA TOUCH between two and nine inches (depending on symbol density) from the symbol, centering the aiming pattern cross hairs on the symbol.

28 JOYA™ TOUCH Resetting the JOYA TOUCH There are three reset methods for the JOYA TOUCH. A ”warm boot” terminates an unresponsive application and clears the working RAM, but preserves both the file system and the registry. A ”cold boot” forces all applications to close and clears working RAM and files not resident on the persistent flash memory. Registry is restored from persistent memory if available or returned to factory default. A ”clean boot” restore the JOYA TOUCH to factory default. Warm Boot A warm boot terminates an unresponsive application and clears the working RAM, but preserves the file system and registry. If an application "hangs" initiate a warm boot to terminate the application. To perform a warm boot, tap Start > Programs > Warm Boot:

User’s Manual 29 Cold Boot A cold boot is a complete reset of the JOYA TOUCH in which all applications are forcibly closed and RAM is completely cleared. Registry is restored from persistent memory if a saved copy is available (see Persistent Registry on page 52) and RAM file system completely erased. You will lose any applications and data (registry too) which are not stored in persistent flash memory. A cold boot is necessary when the Windows Embedded Compact 7 operating system locks up and the warm boot command does not work. To perform a cold boot, lightly press with a metallic clip inside the circle hole on the back for 10 seconds. Clean Boot A clean boot is a complete restore to factory default and backup folder content erase of the JOYA TOUCH. You will loose any applications and data (registry too). To perform a clean boot first execute a cold boot while keeping pressed the Home key. A pop-up will ask you to confirm, confirm by pressing and releasing the Home key for three times, or wait for 3 seconds to cancel.

30 JOYA™ TOUCH NOTE Clean boot may require a considerable amount of time, even a few minutes. Warm Boot Cool Boot Clean Boot Registry Preserved Restored from the latest persistent copy (from flash) Reinitialized Flash Disk (Backup Folder) Preserved Preserved Cleared Object Store (RAM Disk) Preserved Reinitialized, some persistent files could be restored (from flash) Reinitialized Storage Card (if present) Preserved Preserved Preserved CAUTION Before performing a reset, it is recommended to: • Execute a system backup to keep your more important files and applications persistent. • Save the registry to non-volatile memory to guarantee the persistence of the Windows configuration.

User’s Manual 31 Control Panel From the home screen, double-tap My Device icon or tap Start >Settings and then double-tap Control Panel icon to open the control panel main window.

32 JOYA™ TOUCH Data Capture Configuration From the control panel main window, double tap the Decoding icon: There are two sections in the Decoding control panel, each containing additional pages. There are eight general configuration pages and multiple bar code symbology pages.

User’s Manual 33 Configure Select the desired configuration from the options shown in the figure below, and the other Decoding Properties figures on the following pages. Select General, 1D or 2D Bar Code, then use the menu or tap the left and right arrow keys to navigate the different pages of the Decoding utility. The menu options will change to reflect the items most recently selected.

34 JOYA™ TOUCH Notification From the Decoding Properties page, tap Configure > General > Notification. Use to configure the good read green spot, tone and vibration notification. Number Sets the number of notifications (green spot, beep or vibration) the scanner emits on a good read. Duration Sets the duration of the notification (green spot, beep or vibration) the scanner emits on a good read. Interval Sets the interval between each notification (green spot, beep or vibration) the scanner emits on a good read. Volume Sets the volume of beep tone.

User’s Manual 35 Beep Tone Sets the type of beep tone. Good Read From the Decoding Properties page, tap Configure > General > Good Read. Use it to enable good read notifications (green spot, vibrator) and to set the decoding timeout for decoding labels. Select Automatic good read to enable/disable notifications (main enabler), then select the notification you want to use.

36 JOYA™ TOUCH Formatting From the Decoding Properties page, tap Configure > General > Formatting. Allows to format the bar code text by enabling and configuring the use of prefix, suffix and data separator. Label Prefix Select Label prefix to enter the characters you will be using as prefix. Scroll the Add special dropdown menu to select a special character to be added in the current cursor position. Label Suffix Select Label suffix to enter the characters you will be using as suffix. Scroll the Add special dropdown menu to select a special character to be added in the current cursor position.

User’s Manual 37 General Options From the Decoding Properties page, tap Configure > General > General Options. Label Programming Enable Parameter reserved to Datalogic personnel.

38 JOYA™ TOUCH Symbology ID Scroll the Symbology ID dropdown menu to add a code identifier prefix or suffix to the bar code string. The AIM ID (Association for Automatic Identification and Mobility) is an international bar code identifier. When AIM IDs Before is enabled, the AIM ID is inserted at the beginning of the decoded bar code. DL IDs is a Datalogic specific character identifier. User IDs is a user specific character identifier you can set in the related symbology settings menu.

User’s Manual 39 Group Separator Replacement The group separator replacement is a non printable data separator character (ASCII code 1D hex). Use the Group separator replacement to select a special character that will be used as GS data separator substituting the standard GS character. Remove Non-printable Characters Select it to remove non-printable characters from a unicode string.

40 JOYA™ TOUCH Decoding Options From the Decoding Properties page, tap Configure > General > Decoding Options. Use it to configure the User ID for symbologies, Redundancy and Aggressive Decoding (if supported by the decoding module). Select a symbology to view or change the available properties settings.

User’s Manual 41 Imager Options From the Decoding Properties page, tap Configure > General > Imager Options. Use it to customize the JOYA TOUCH scanning behavior. Enable Illumination If selected, it causes the scanner to turn on the illumination to aid decoding. Enable Picklist If selected, it allows you to pick and decode a bar code from multiple bar codes printed close together, when the scan illumination intersects more than one bar code. Only the targeted bar code will be returned.

42 JOYA™ TOUCH Target Mode If enabled, when the scan button is pressed, the scanner will project an aiming pattern to assist in centering over the bar code before scanning. Scroll the Target mode dropdown menu to select the desired targeting behavior: No Delay Target mode is disabled.

User’s Manual 43 Target Timeout If selected, scanning takes place after a programmable time upon pressing the scan button. Drag the Timeout slider to set the maximum amount of time the scanner attempt to decode after target timeout: Release Scan If selected, scanning takes place after the scan button is released. Drag the Timeout slider to set the scanning timeout after releasing the scan button:

44 JOYA™ TOUCH Multi Scan The JOYA TOUCH scanner allows you to scan multiple bar codes by one scan. From the Decoding Properties page, tap Configure > General > Multi Scan and drag the Labels per good read slider to set the number of bar codes allowed to be read per scan. Select Enable indicators for each label to enable notifications for each bar code thet is scanned.

User’s Manual 45 Keyboard Wedge From the Decoding Properties page, tap Configure > General > Keyboard Wedge. Select Bar code to enable the wedge mode.

46 JOYA™ TOUCH 1D Bar Code Symbology Pages Each bar code symbology can be customized with additional settings that may affect that specific bar code decoding. Scroll the drop-down menus from Configure > 1D Bar Code, or tap the left and right arrow keys to navigate the 1D bar code symbology pages and configure symbology decoding options:

User’s Manual 47 Refer to the sample symbology control panels for examples of the types of fields and options you can modify. The sample below shows the settings of a Code 128 bar code symbology:

48 JOYA™ TOUCH 2D Bar Code Symbology Pages Scroll the drop-down menus from Configure > 2D Bar Code, or tap the left and right arrow keys to navigate the 1D bar code symbology pages and configure symbology decoding options: Refer to the sample symbology control panels for examples of the types of fields and options you can modify. The sample below shows the settings of a DataMatrix bar code symbology:

User’s Manual 49 Decoding Settings Select from the Decoding Properties Settings menu to restore previous configurations and/or other available default settings. Choose from: • Factory Defaults • Minimum Settings • Maximum Settings • Save • Revert to Saved Settings The settings are saved when you tap ‘Yes’. To permanently save these settings you need to save the registry using the Persistent Registry applet in the Control Panel. When open, Decoding Properties acts as a simple bar code test tool that provides the Data decoded and the Data Type of the bar code scanned.

50 JOYA™ TOUCH DL Buttons You can use the DL Buttons tab to associate specific keys with specific applications. From the control panel main window, double tap the DL Buttons icon. As for the Joya Touch, it is possible to program the Home key and the Trigger, if present. On the DL Buttons tab, customize the program hardware buttons to launch your most used applications. Under Select a button, select the button you want to assign a function to, and then select a program from Assign a function. Tap OK to confirm.

User’s Manual 51 Triggers Triggers are special customizable buttons that are mapped by default by DL Buttons. Also, they can be set as wakeup buttons: TRIGGERS AVAILABLE FUNCTIONS Scan Bar Code function activates the scanner. Pistol Trigger

52 JOYA™ TOUCH Persistent Registry The Registry stores information that are necessary to configure the system for applications and hardware devices. The Registry also contains information that the operating system continually references to during operation. To persist the Registry settings between boots, do the following steps: 1. Double-tap the Control Panel icon on the home screen. 2. Double-tap the Persistent Registry icon. 3. Tap the Persist button. 4. Tap OK to exit.

User’s Manual 53 To change Persistent Registry timing, do the following steps: 1. Select a time interval from the menu. 2. Tap OK to save and exit. To deselect Persistent Registry timing, do the following steps: 1. Deselect the Persist registry settings check box. 2. Tap OK to save and exit.

54 JOYA™ TOUCH Wireless Communications Wireless networking has a customized control, Laird Connection Manager (LCM), specific to the radio. LCM allows you to view all radio and security settings, and status. It also enables you to troubleshoot connectivity issues. To access LCM, double-tap the Laird Connection Manager icon on the home screen, or tap Start > Programs > Laird Connection Manager. Status Tab The Status tab provides status information on the radio's Wi-Fi connection between the client device and the access point to which it's associated. Status Indicates the current status of the Laird Wi-Fi radio. Connection statuses include: • Down The radio is not recognized by Laird software and therefore is not associated or authenticated.

User’s Manual 55 • Disabled The radio is disabled. To enable the radio, check the Wi-Fi check box located on the Configuration window. When the radio is disabled, it does not attempt to make a connection to an access point. • Not Associated The radio has not established a connection to an access point. • Associated The radio has established a connection to an access point but is not EAP authenticated. The radio cannot communicate unless it is associated and EAP authenticated. • Connected to [SSID] The radio is connected to the named SSID. IP Address Displays the IP address of the Wi-Fi device. Signal Strength Displays the signal strength (or RSSI) in dBm. NOTE If the Encryption type is set to WEP or Open (None), it can communicate (send data) while in the Associated state.

56 JOYA™ TOUCH Configuration Tab The Configuration tab allows Wi-Fi to be enabled and disabled. It also allows users to manage and scan for Wi-Fi profiles. Check on/off box Check to enable or disable Wi-Fi Active Profile Displays the name of the active profile. Use the drop-down menu to select a different profile. Profiles Allows user to change profiles and global configurations, and enables administrative abilities. There are two tabs listed under Manage Profiles: • Wi-Fi - Profile Profile settings are radio and security settings that are stored for each configuration profile. The Profile tab displays the following properties and options:

User’s Manual 57 - Property and Value table: displays the properties of each profile and its respective value. - Profile drop-down menu: displays the current profile and a list of all profiles previously configured or used. - New: allows a profile to be added to the list. - Delete: deletes a profile from the list. - Value box: displays the value of a prospective property. - Commit: saves the changed value. • Wi-Fi - Globals The Globals tab displays the source device's Wi-Fi global values that apply to all profiles and settings that apply to LCM itself. The following subsections allow these values to be modified:

58 JOYA™ TOUCH - Property and Value table: displays various properties and their respective values. - Value box: displays the current and avaliable alternative values for the selected property. - Commit: saves the changed value. NOTE When you tap Commit, a registry flush occurs for all settings.

User’s Manual 59 Scan Opens the scan window to scan the area for available SSIDs. Also displays RSSI and security. Diagnostics Tab The Diagnostics tab enables you to troubleshoot connection issues within LCM.

60 JOYA™ TOUCH Wi-Fi Status enabled/disabled About Tap to display LCM information including driver and the LCM version. Advanced Tap to display advanced settings for Wi-Fi, strength percentage, and quality percentage. There are three drop-down options: • Status

62 JOYA™ TOUCH Audio Settings There are two applets that control volume: Audio and Volume & Sounds. Audio From the control panel main window, double-tap the Audio icon: The audio control panel can be used to independently set the playback or recording volume for different types of audio inputs and outputs, such as a headset, powered mobile dock, or the internal speakers and microphone.

64 JOYA™ TOUCH Volume & Sounds From the control panel main window, select the Volume & Sounds applet by double tapping the Volume & Sounds icon: The Volume & Sounds applet configures audio features of all speakers and headphones and appears as follows:

User’s Manual 65 Connecting to other Computers Windows Mobile® Device Center The desktop application Windows Mobile® Device Center gives you the ability to synchronize information between a desktop computer and your JOYA TOUCH. Synchronization compares the data on the JOYA TOUCH with that on the desktop computer and updates both with the most recent information. Windows Mobile Device Center is only compatible with Windows Vista and Windows 7; if you run Windows XP or earlier, you have to download Microsoft ActiveSync. To establish a partnership between the JOYA TOUCH and a host PC, start Windows Mobile® Device Center and follow the steps below: 1. Connect the JOYA TOUCH to the host PC. Windows Mobile® Device Center configures itself and then opens. 2. On the license agreement screen, click Accept. 3. On the Windows Mobile Device Center’s home screen, click Set up your device. 4. Select the information types that you want to synchronize, then click Next. 5. Enter a device name and click Set Up.

66 JOYA™ TOUCH Datalogic Firmware Utility The Datalogic devices are equipped with a field upgradeable firmware mechanism. Firmware updates are available on the Datalogic website: http://www.datalogic.com/eng/support-services/automatic-datac apture/downloads/software-utilities-sw-2.html. After you have downloaded the desired update, there are several ways you can update the firmware on your device. • Use Wavelink Avalanche™ if you have multiple Datalogic devices to update. For more information refer to the dedicated section of the Wavelink website. • If Wavelink Avalanche™ is not available or you have only a few Datalogic devices to update, use the Datalogic Firmware Utility (DFU), described below, to install or update the firmware using an ActiveSync connection. The following sections provide procedures for the retrieval and installation of the most current firmware image onto a Datalogic device. Retrieving a Firmware Image Update The following instructions use Internet Explorer to retrieve the most current firmware image. 1. Launch Internet Explorer on your PC and navigate to the Datalogic website. 2. Navigate to the Downloads section of the website. 3. Using the device selection fields, select the file you want to download, then click Save to begin copying the files to your local machine (or local network location).

User’s Manual 67 Installing DFU on the Host PC The Datalogic Firmware Utility (DFU) provides administrators with a field upgrade mechanism. You must have Microsoft® ActiveSync (for Windows XP devices) or Windows Mobile® Device Center (for Windows 7 and Vista devices) already loaded and running on the host PC to use DFU. See “Windows Mobile® Device Center” on page -65 for more information. To install the Datalogic Firmware Utility, complete the following steps on the PC: 1. Go to the Datalogic website and download the most current version of the Datalogic Firmware Utility. Unzip the file, then double-click to run DFU_Setup.exe. 2. Click OK to continue once you have removed previous versions of DFU. 3. The Welcome to DFU Setup Program screen opens. - Please exit all Windows applications before running this installer. - Click Next to continue the Setup. 4. Follow the onscreen instructions to complete the installation. NOTE Prior to installing, you must remove any previous versions of DFU installed on the host PC.

68 JOYA™ TOUCH Updating the Firmware After copying the firmware image to the host PC and installing DFU, you can upgrade the firmware on your Datalogic device. 1. Go to Start > Programs > Datalogic > DFU > Datalogic Firmware Utility. 2. Verify that ActiveSync is selected by clicking Communications > WMDC/ActiveSync. 3. Click browse (...) and navigate to the location where you saved the firmware file for your terminal. 4. Select the current *.out file and click Open. 5. Click Update. 6. DFU will compare the selected firmware image with the firmware already loaded on the device; if the image is compatible with the connected device, DFU will proceed to update the firmware image on your device. After the firmware of your device has been updated, the program will automatically perform a warm reset of the device. NOTE The following steps require that you have already established an ActiveSync or Windows Mobile® Device Center connection between the host computer and the Datalogic device.

User’s Manual 69 Datalogic Desktop Utility Datalogic Desktop Utility (DDU) allows administrators to configure Windows® CE and Embedded Handheld devices to control individual user access. This includes the ability to: • Prevent users from changing your device OS settings. • Use Application Selector to replace the desktop with a selection of authorized applications. • Restrict user access in Internet Explorer (and customized error recovery mechanisms). To open DDU, access the Control Panel and double-tap the Datalogic Desktop Utility icon.

70 JOYA™ TOUCH Administrative Options (Admin tab) When you open the DDU control panel, the Admin tab appears. COMMAND DESCRIPTION Enable Datalogic Desktop Tap this checkbox to activate the DDU functions such as Windows Access Restrictions and Application Selector. Enter Password Enter a password in the text box. This allows the user to specify a password when this utility is launched. By default the password is ”blank”. A password can consist of all standard keyboard characters. Re-Enter Password Carefully re-enter the password in the second text box. Set Password Tap Set Password to enable the password. To change or remove the password, enter a new value, re-enter the new value, and tap Set Password. Set Defaults Tap Set Defaults to reset the default values of all the functions on all the tabs. After you select this option, you will receive a prompt to verify this selection.

User’s Manual 71 Setting a Password To set a password: 1. Enter a password in the field using the virtual keyboard. This allows the user to specify a password when this utility is launched. By default the password is ”blank”. 2. Re-enter the password in the second field. 3. Tap Set Password to enable the password. 4. Tap OK to close the Set Password Confirmation dialog. NOTE Be sure to record the password for future reference.

72 JOYA™ TOUCH NOTE You must tap Set Password prior to exiting DDU in order to store and activate your new password. It is not necessary to select Enable Datalogic Desktop. CAUTION If you tap Set Defaults it will remove all custom settings and restore all the factory default settings, except a previously set password.

User’s Manual 73 Changing a Password To change to a new password: 1. Enter a new value in the Enter Password field. 2. Re-enter the new value in the Re-enter Password field. 3. Tap Set Password. Removing a Password To remove a password: 1. Enter blanks in both Password fields. 2. Tap Set Password. Password Request Dialog Box Once the password is set, next time you open the Datalogic Desktop Utility, the DDU Password dialog box opens. This dialog box will only open if a password was defined:

74 JOYA™ TOUCH 1. Type in your password using either the keypad on the unit, or using the stylus on the soft input panel (SIP). If you enter an incorrect password, the system will prompt you to input the correct one. 2. Select/tap OK to verify the password. Or tap X to cancel.

User’s Manual 75 Locked Web Browser Options (LockedWeb tab) Tap the LockedWeb tab to access the Locked Web Browser Configuration. For additional information about Locked Web Browser commands and metatags, see Locked Web Browser on page 83. Error Page Redirection Use the Error Redirection option to provide customized recovery from common errors. When an error occurs, the browser can redirect access to a specified error page with instructions on how to recover from the problem. Error Redirection Options Error Type The “Error Type” pull-down list displays available Error Types: (400) Invalid Syntax, (403) Request Forbidden, (404) Object Not Found, (406) No Response Format, (410) Page Doesn't Exist, (500) Internal Server Error, (501) Server Can't Do That, Generic Error, Network Disconnected. Error Page Edit this textbox to associate a website or html file with the specified error.

76 JOYA™ TOUCH Other Options Full Screen Set the web browser in full screen mode. Status Icon Enable or disable the status icons view. The status icons can be configured on the Status tab of DDU. Trap Keys When checked: • all key presses will be trapped by the Locked Web Browser to prevent the user from accessing unsafe parts of the system. For example, pressing Ctrl+O to Open a File will not work; • safe key presses (e.g. Alpha numeric) will still get processed by the Locked Web Browser as normal. For example entering a number in a text field on a web page; • DL Buttons keys will not work in the LockedWeb Browser; • all Locked Web Browser command keys will work (e.g. Ctrl+0 to exit). When unchecked: • all keys will be processed normally by the system and the browser; • DL Buttons keys will work normally; • all Locked Web Browser command keys will work (e.g. Ctrl+0 to exit). Other Options Exit Password When checked, a password will be required before the Locked Web Browser can exit. This password is different than the DDU exit password, with a default value of “0000”. Browser Home Page This sets the Internet Explorer home page, regardless of the enable state of the Locked Web Browser.

User’s Manual 77 Status Icons Options (Status Tab) Tap the Status tab to access the Status Icons option. You can configure the view of some status icons that are used in LockedWeb and in Application Selector to display the status of Wi-Fi radio and battery. Status Icons Options Icon Size Sets the status icons’ size. Icon Location Selects the preferred location for each status icon.

78 JOYA™ TOUCH Windows Control Select/tap the Win (Windows Controls) tab to access the Windows Controls option. Use Windows controls to allow or restrict access to Windows system functions. You can disable normal Windows functions such as the taskbar, leaving nothing but a blank workspace. This allows applications to be run in full screen mode and prevents users from accidental or unauthorized use of the taskbar, Internet Explorer, and any other resident applications. WIndows Controls Show Taskbar Tap Show Taskbar to specify whether the Taskbar is displayed or not. Taskbar Enabled Tap Taskbar Enabled to specify whether the taskbar is accessible. This option is only available when the Show Taskbar is checked. Start Menu Enabled Tap Start Menu Enabled to specify whether the Start Menu is displayed or not. This option works only when Task Bar Enabled is checked. AutoSIP Enabled Enables the AutoSIP Windows feature.

User’s Manual 79 Scroll Bars Enabled This control only takes effect in Locked Web Browser. When checked, displays horizontal and vertical scroll bars to help view large web pages which do not fit the screen. When unchecked, scroll bars will not be present. Widows CE Desktop Enabled When selected, CE Desktop is disabled, so application icons can’t be activated. NOTE Changes require a device reboot. WIndows Controls

80 JOYA™ TOUCH AppSelector Options (AppSelect tab) Tap the Application Selector (AppSelect Tab) to edit, add, or delete applications for the application selector. Application Selector Options Enable Application Selector Tap Enable Application Selector to enable/disable the application selector. When enabled, the Application Selector replaces the desktop and allows only authorized use of applications. Show status icons Enable or disable the status icons view. The status icons can be configured on the Status tab of DDU. Authorized Applications This is a list of applications that the user can access. Application Selector Commands New Tap New to create a new application entry. Edit Tap Edit to edit the selected entry. Del This is a list of applications that the user can access. Up/Down Tap Del to delete the selected entry.

User’s Manual 81 Add Applications The Add Application dialog opens when you tap either New or Edit. From the Add Application dialog the administrator can configure and/or add/change a new application entry in the list. Applications with the Run Application at Startup option enabled will start automatically when the Application Selector starts up. COMMAND DESCRIPTION Application Title Type the name of the application in this textbox in the way you wish it to appear for the user. Executable Displays the path for the executable file which you want to run. Browse Browse for the desired executable file. The results of this search are placed in the Executable textbox. Arguments Type any command line arguments to be used when an application is executed.

82 JOYA™ TOUCH Icon File Tap Set Defaults to reset the default values of all the functions on all the tabs. After you select this option, you will receive a prompt to verify this selection. Browse Browse for the desired icon file. The results of this search are placed in the Icon File textbox. Run Application at Startup Tap this box to force this application to auto start when the Application Selector starts up. Applications will be started in the order listed in the authorized application list. Delay Enter a delay duration in seconds in the combo box. This option delays auto start of application(s) to allow drivers to load prior to starting applications. OK Tap OK to add/save changes. X X Select/tap X to cancel the creation of this entry. COMMAND DESCRIPTION

User’s Manual 83 Locked Web Browser The Locked Web Browser is a browser helper object for Internet Explorer. It allows an administrator to define a restricted internet usage environment. Once in the restricted environment, a password is required to exit. This means users can only access web applications and websites set by the administrator. To launch the application, go to \Windows\WebAppLock.exe. In Full Screen mode, status icons may be used to display signal strength and battery state. For CE, a non-full screen mode exists that allows the status bar to be displayed but with user interaction disabled. The following command line arguments are supported: • /E optional parameter which allows for Exit without entering a password • @URL optional parameter which specifies a URL to use as a home page. • /C optional parameter which disables the ctrl keys (including the one to exit). NOTE Configuration is set up through the DDU control panel. See Locked Web Browser Options (LockedWeb tab) on page 75 for more information.

84 JOYA™ TOUCH FlashDisk Directory File Management All of the Windows Embedded Compact 7 system files reside in RAM (volatile memory) except for the FlashDisk directory, which resides in FLASH (non-volatile memory). Therefore the contents of the FlashDisk directory are persistent even if the mobile computer is rebooted or the battery pack is changed. You can save your more important files that you don't want to lose due to mobile computer reboot, in the FlashDisk directory or create a sub-directory within FlashDisk. Even though the Windows Directory resides in RAM, it often contains files or sub-directories created by the user or by installation programs that you don't want to lose at re-boot. To keep these files persistent it is necessary to copy them to the directory \FlashDisk\Windows. This directory doesn't exist originally (only FlashDisk exists), and therefore it must be created. At the next cold boot, before activating the shell, Windows Embedded Compact 7 will copy the contents including all sub-directories of \FlashDisk\Windows to \Windows. Likewise, to maintain files that must be run at Windows Embedded Compact 7 startup, (i.e. .exe, .lnk, .vb, .htm, etc.), it is necessary to copy them to the directory \FlashDisk\Startup. This directory does not exist originally (only FlashDisk exists), and therefore it must be created. The applications programs will be run after any type of re-boot (both software and cold boot). However, since file system persistence is performed after the “\FlashDisk\Startup” folder execution, for those programs which depends upon the DLLs and resources copied from “\FlashDisk\Windows” to “\Windows” during the cold-boot, the “\FlashDisk\Windows\dl_startup” folder is to be preferred to execute programs and applications, since the execution follows the

User’s Manual 85 file system restore (and no DLL and resource dependence failure will occur). As an alternative to the Safe Setup function, it is possible to copy the .cab files to the directory \FlashDisk\Cabfiles (the Cabfiles sub-directory doesn't exists originally and must therefore be created) and perform a mobile computer cold boot to have the application installed. Once these files are copied to the directory \FlashDisk\Cabfiles, the application will be run after each re-boot. From the second cold boot on, a message may be displayed such as " is already installed. Reinstall?". This message blocks the boot process. Press the [Enter] key to continue the system initialization. In a specific JOYA TOUCH version, a 4GB DS type card is available as permanent general purposes storage device (path = \Storage Card).

You can use any standard micro USB cable to directly connect the Datalogic JOYA TOUCH to a host computer to transfer data through the USB interface. NOTE Connection through the cable complies to USB 2.0 standard. Host Computer JOYA TOUCH Standard Micro USB cable type USB A – micro USB B

communicate with the host using the on-board radio frequency component and an Access Point connected to the host computer. To launch this utility you can tap the specific icon if it's visible on the taskbar or you can open Connections folder or Control Panel from desktop. NOTE Wi-Fi module is on by default, in order to avoid wasting energy, you can switch it off using the Wireless Communications applet. JOYA TOUCH JOYA TOUCH Access Point Host

radio and drops the radio connection. When the terminal resumes, depending on the radio power mode and security protocol selected, it may take up to 30 seconds for the 802.11 a/b/g/n radio driver to re-associate the radio to the network. NOTE Area coverage and radio performance may vary, due to environmental conditions, access point types or interference caused by other devices (microwave ovens, radio transmitters, etc.).

JOYA TOUCH models can communicate with a Bluetooth® printer, using the on-board Bluetooth® module. NOTE Bluetooth® is only available in Joya Touch plus models. NOTE In order to extend battery life, the Bluetooth® module is off by default. If you need to have Bluetooth® working, the module must be powered on. NOTE Suspending the terminal powers off the Bluetooth® radio and drops the Bluetooth® connection. When the terminal resumes, it takes approximately 10 seconds for the Bluetooth® radio driver to re-initialize the radio.

vary, due to environmental conditions or interference caused by other devices (microwave ovens, radio transmitters, etc.).

WARNING Use only the supplied or an approved replacement antenna. Unauthorized antennas, modifications or attachments could damage the product and may violate laws and regulations. Most modern electronic equipment is shielded from RF signals. However, certain electronic equipment may not be shielded against the RF signals generated by JOYA TOUCH. Datalogic recommends persons with pacemakers or other medical devices to follow the same recommendations provided by Health Industry Manufacturers Associations for mobile phones. Persons with pacemakers: • Should ALWAYS keep this device more than twenty five (25) cm from their pacemaker and/or any other medical device; • Should not carry this device in a breast pocket; • Should keep the device at the opposite side of the pacemaker and/or any other medical device; • Should turn this device OFF or move it immediately AWAY if there is any reason to suspect that interference is taking place. • Should ALWAYS read pacemaker or any other medical device guides or should consult the manufacturer of the medical device to determine if it is adequately shielded from external RF energy. In case of doubt concerning the use of wireless devices with an implanted medical device, contact your doctor.

regulations posted in these areas instruct you to do so. Hospitals or health care facilities may use equipment that could be sensitive to external RF energy. WARNING RF signals may affect improperly installed or inadequately shielded electronic systems in motor vehicles. Check with the manufacturer or its representative regarding your vehicle. You should also consult the manufacturer of any equipment that has been added to your vehicle. WARNING An air bag inflates with great force. DO NOT place objects, including either installed or portable wireless equipment, in the area over the air bag or in the air bag deployment area. If a vehicle’s wireless equipment is improperly installed and the air bag inflates, serious injury could result.

explosive atmosphere. Observe restrictions and follow closely any laws, regulations, warnings and best practices on the use of radio equipment near fuel storage areas or fuel distribution areas, chemical plants or where any operation involves use of explosive materials. Do not store or carry flammable liquids, explosive gases or materials with the device or its parts or accessories. Areas with a potentially explosive atmosphere are often, but not always, clearly marked or shown. Sparks in such areas could cause an explosion or fire, resulting in injury or even death.