Datalogic QuickScan Mobile Reference Manual

959 Terry Street Eugene, Oregon 97402 USA Telephone: (541) 683-5700 Fax: (541) 345-7140 An Unpublished Work - All rights reserved. No part of the contents of this documentation or the procedures described therein may be reproduced or transmitted in any form or by any means without prior written per-mission of Datalogic Scanning, Inc. or its subsidiaries or affiliates ("Datalogic" or “Datalogic Scanning”). Owners of Datalogic products are hereby granted a non-exclusive, revocable license to reproduce and transmit this documentation for the purchaser's own internal business purposes. Purchaser shall not remove or alter any proprietary notices, including copyright notices, contained in this documentation and shall ensure that all notices appear on any reproductions of the documentation. Should future revisions of this manual be published, you can acquire printed versions by contacting your Datalogic representative. Electronic versions may either be downloadable from the Datalogic website (www.scanning.datalogic.com) or provided on appropriate media. If you visit our website and would like to make comments or suggestions about this or other Datalogic publications, please let us know via the "Contact Datalogic" page. Disclaimer Datalogic has taken reasonable measures to provide information in this manual that is complete and accurate, however, Datalogic reserves the right to change any specification at any time without prior notice. Datalogic is a registered trademark of Datalogic S.p.A. in many countries and the Datalogic logo is a trademark of Datalogic S.p.A. all licensed to Datalogic Scanning, Inc. All other trademarks and trade names referred to herein are property of their respective owners.

2 INSTALLATION............................................................................................ 3 3 CONFIGURATION........................................................................................ 9 RS-232 PARAMETERS.............................................................................. 20 Baud Rate................................................................................................... 21 Parity........................................................................................................... 22 Data Bits ..................................................................................................... 22 Stop Bits...................................................................................................... 23 Handshaking............................................................................................... 23 Ack/Nack Protocol....................................................................................... 24 Fifo.............................................................................................................. 24 Inter-character Delay................................................................................... 25 Rx Timeout.................................................................................................. 25 Serial Trigger Lock...................................................................................... 26 USB PARAMETERS .................................................................................. 27 Handshaking............................................................................................... 28 Ack/Nack Protocol....................................................................................... 28 Fifo.............................................................................................................. 29 Inter-character Delay................................................................................... 29 Rx Timeout.................................................................................................. 30 Serial Trigger Lock...................................................................................... 30 Keyboard Nationality................................................................................... 31 Fifo.............................................................................................................. 32 Inter-character Delay................................................................................... 32 Inter-code Delay.......................................................................................... 33 Control Character Emulation....................................................................... 33 USB Keyboard Speed................................................................................. 34 WEDGE PARAMETERS............................................................................. 35 Keyboard Nationality................................................................................... 36 Caps Lock................................................................................................... 37 Caps Lock Auto-Recognition (IBM AT compatible only)............................... 37 Num Lock.................................................................................................... 38 Inter-character Delay................................................................................... 38 Inter-code Delay.......................................................................................... 39 Keyboard Setting......................................................................................... 40 Control Character Emulation....................................................................... 42

Operating Mode .......................................................................................... 44 Minimum Output Pulse................................................................................ 45 Conversion to Code 39 and Code 128........................................................ 46 Overflow...................................................................................................... 47 Output Level................................................................................................ 47 Idle Level..................................................................................................... 48 Inter-Block Delay......................................................................................... 48 IBM 46xx .................................................................................................... 49 IBM Data Formatting................................................................................... 50 DATA FORMAT.......................................................................................... 51 Code Identifier............................................................................................. 54 Custom Code Identifier ............................................................................... 55 Header ........................................................................................................ 56 Terminator................................................................................................... 57 Special Keys ............................................................................................... 58 Field Adjustment ......................................................................................... 59 Field Adjustment Character......................................................................... 60 Code Length Tx .......................................................................................... 60 Character Replacement .............................................................................. 61 Address Stamping....................................................................................... 63 Address Delimiter........................................................................................ 63 READING PARAMETERS.......................................................................... 64 Hand-Held Operation .................................................................................. 65 Stand Operation.......................................................................................... 65 Hardware Trigger Mode .............................................................................. 66 Trigger-off Timeout ..................................................................................... 66 Flash Mode ................................................................................................. 67 Reads per Cycle.......................................................................................... 67 Safety Time................................................................................................. 68 Beeper Intensity.......................................................................................... 68 Beeper Tone ............................................................................................... 69 Beeper Type ............................................................................................... 69 Beeper Length ............................................................................................ 69 Stand Recognition Beep ............................................................................. 70 DECODING PARAMETERS....................................................................... 71 Ink Spread................................................................................................... 72 Overflow Control ......................................................................................... 72 Interdigit Control.......................................................................................... 73 Decoding Safety.......................................................................................... 73 Puzzle Solver™ .......................................................................................... 74

EAN/UPC Family ........................................................................................ 77 2/5 Family ................................................................................................... 84 Code 39 Family........................................................................................... 85 Code 128 Family......................................................................................... 87 Code 93 ...................................................................................................... 88 Codabar Family........................................................................................... 89 MSI ............................................................................................................. 91 Plessey ....................................................................................................... 92 Telepen....................................................................................................... 93 Delta IBM .................................................................................................... 94 Code 11 ...................................................................................................... 95 Code 16K.................................................................................................... 96 Code 49 ...................................................................................................... 96 GS1 DataBar™........................................................................................... 97 ADVANCED FORMATTING ....................................................................... 98 Concatenation............................................................................................. 99 Advanced Formatting................................................................................ 102 RADIO PARAMETERS............................................................................. 117 Radio Protocol Timeout............................................................................. 118 Power-Off Timeout.................................................................................... 118 Beeper Control for Radio Response ......................................................... 119 Single Store .............................................................................................. 120 Batch Mode............................................................................................... 121 4 REFERENCES ......................................................................................... 122 5 TECHNICAL FEATURES ......................................................................... 145 A HOST CONFIGURATION STRINGS........................................................ 150 B CODE IDENTIFIER TABLE...................................................................... 163 C HEX AND NUMERIC TABLE ................................................................... 166

Trigger Reading Window Cradle Locking System Latch Charge completed (yellow LED) Charging (red LED)

handheld device without compromise in performance. The extensive range of models and options of this family can easily meet any specific challenges required by retail, and commercial data collections applications. The QuickScan® Mobile is the ideal solution for retail and commercial environments where continuous and multi-tasking activities are keys to optimum productivity, lower cost of ownership and profitable business. 1.1 READING ANGLE QuickScan® Mobile readers automatically scan barcodes at a distance. Simply aim and pull the trigger. Code scanning is performed along the center of the light bar emitted from the reading window. This bar must cover the entire code. Successful scanning is obtained by tilting the reader with respect to the barcode to avoid direct reflections, which could impair the reading performance. See the figures below. Successful reading is obtained by an audible tone. OK Not Advised Good read LED

pushing up the locking system as indicated in the following figure.

Follow the procedure below to start using your QuickScan® Mobile reading system: 1. Connect a QuickScan® Mobile cradle to the Host. 2. Insert the QuickScan® Mobile reader into the cradle to start the battery charging. A full charge of the Lithium battery takes 3.5 – 6 hours. NOTE To achieve the best battery life, it is recommended to perform a full battery charge before using the reader in hand-held mode. In hands-free use, you can immediately start using the reader, since it is powered by the cradle. 3. Configure the QuickScan® Mobile reader. 4. Configure the QuickScan® Mobile cradle. 2.2 CHANGING THE BATTERIES To change the battery of your reader, you must: 1. Unscrew the battery cover screw (Figure 1). 2. Unplug the white connector and remove the old battery (Figure 2). 3. Insert the new battery and plug in the white connector. NOTE When inserting the new battery into the handle pay attention to position the battery and the connector just as shown in Figure 3. Figure 1 Figure 2 Figure 3

Figure 4 WARNING Do not incinerate, disassemble, short terminals or expose to high temperature. Risk of fire, explosion. Use specified charger only. Risk of explosion if the battery is replaced by an incorrect type. Dispose of the batteries as required by the relevant laws in force.

You can connect the QuickScan® Mobile cradle to the Host through the dedicated connector, using the cable corresponding to the desired interface type. 1. Connect the appropriate interface cable to the cradle by simply plugging it into the Host connector on the base of the cradle. QuickScan® Mobile Cradle - Bottom View To disconnect the cable, insert a paper clip or other similar object into the hole corresponding to the connector on the base of the cradle. Push down on the clip while unplugging the cable. Refer to the following figure: Disconnecting the Cable Interface Cable

2.7 WEDGE CONNECTION (only for Quickscan M2 Type:130) CAB-413 CAB-391 or CAB-321 + CAB-431

2.9 PEN EMULATION CONNECTION CAB-431 POWER SUPPLY ADAPTER CAB-431 POWER SUPPLY ADAPTER CAB-445 CAB-446

This manual can be used for complete setup and configuration of your reader by following the setup procedures in this chapter. If you wish to change the default settings, this manual provides complete configuration of your reader in an easy way. To configure your reader: 1. Open the folded page in Appendix C with the hex-numeric table and keep it open during the device configuration. 2. Read the Enter Configuration code ONCE, available at the top of each page of configuration. 3. Modify the desired parameters in one or more sections following the procedures given for each group. 4. Read the Exit and Save Configuration code ONCE, available at the top of each page of configuration. Reference notes describing the operation of the more complex parameters are given in chapter 4. 3.1.2 Datalogic Aladdin™ Datalogic Aladdin™ is a multi-platform utility program that allows device configuration using a PC. It provides RS-232 interface configuration as well as configuration barcode printing. 3.1.3 Copy Command A previously configured device (Master), can be used to send its configuration directly to other devices of the same type (Slaves). The particular procedure for each device is given.

An alternative configuration method is provided in Appendix A using the RS-232 or USB-COM interface. This method is particularly useful when many devices need to be configured with the same settings. Batch files containing the desired parameter settings can be prepared to configure devices quickly and easily. 3.2 QUICKSCAN® MOBILE STAND ALONE SETUP Read the restore default parameters code below. Restore QuickScan ® Mobile Default 1. Ì$+$*oÎ 2. Read the codes below to set the radio address of the QuickScan® Mobile reader. Enter configuration Ì$+;Î Set Radio Address 3. ÌRA0RFHÎ + four digits for the QuickScan® Mobile Address (from 0000 to 1999). All readers used in the same area must have different addresses. Exit and Save configuration 4. Ì$-?Î 5. Read the Bind code to pair the QuickScan® Mobile to the cradle. The reader is dedicated to the cradle. Any previously bound reader will be excluded. Bind Ì$+RN0$-IÎ The yellow LED on the QuickScan® Mobile will blink; the reader is ready to be positioned onto the cradle.

emitted, signaling that the cradle has been paired to the QuickScan® Mobile, and the yellow LED on the reader will go off. Read the cradle restore default code: 7. Restore cradle default Ì$+RX0$-qÎ Go to par. 3.3 Interface Selection. Yellow LED

RS-232 Standard Ì$+CP0$-$Î POS Terminals Nixdorf Mode A Ì$+CM2EC0$->Î Fujitsu Ì$+CM1$-ÈÎ ICL Mode Ì$+CM0$-ÃÎ For POS terminal default settings refer to par. 4.9. PEN Ì$+CP6$-BÎ

IBM AT or PS/2 PCs Ì$+CP500$-aÎ IBM XT Ì$+CP503$-vÎ PC Notebook Ì$+CP505$-ÈÎ IBM SURE1 Ì$+CP506$-$Î IBM Terminal 3153 Ì$+CP504$-}Î

To select the interface for these IBM Terminals, read the correct KEY TRANSMISSION code. Select the KEYBOARD TYPE if necessary (default = advanced keyboard). KEY TRANSMISSION MODE make-only keyboard Ì$+CP502$-oÎ make-break keyboard Ì$+CP501$-hÎ KEYBOARD TYPE � advanced keyboard Ì$+FK1$-ÉÎ typewriter keyboard Ì$+FK0$-ÄÎ

independently from the Keyboard Nationality used. You do not need to make a Keyboard Nationality selection. (default = Num Lock Unchanged). Make sure the Num Lock key on your keyboard is ON. IBM AT - ALT mode Ì$+CP507$-+Î PC Notebook - ALT mode Ì$+CP508$-2Î WYSE TERMINALS ANSI Keyboard Ì$+CP509$-9Î PC Keyboard Ì$+CP510$-gÎ ASCII Keyboard Ì$+CP511$-nÎ VT220 style Keyboard Ì$+CP514$-ÇÎ

PORT 9B 4501 Protocol Ì$+CP800$-pÎ (typical) 1520 Protocol Ì$+CP801$-wÎ PORT 5B 1520 Protocol Ì$+CP801$-wÎ (typical) 4501 Protocol Ì$+CP800$-pÎ

The USB interface is compatible with: Windows 98 (and later) IBM POS for Windows Mac OS 8.0 (and later) 4690 Operating System USB Start-up As with all USB devices, upon connection, the Host performs several checks by communicating with the QuickScan® Mobile. During this phase the yellow LED on the QuickScan® Mobile reader blinks and normal operations are suspended. Two basic conditions must be met before the QuickScan® Mobile is ready to read codes, the correct USB driver must be loaded and sufficient power must be supplied to the reader. For all systems, the correct USB driver for the default USB-KBD interface is included in the Host Operating System and will either be loaded automatically or will be suggested by the O.S. and should therefore be selected from the dialog box (the first time only). Normally the Host supplies sufficient power to the reader, the start-up phase ends correctly, the yellow LED stops blinking. In rare cases, if the Host does not supply sufficient power to the reader, a dialog box will appear on the Host and the reader will be blocked (yellow LED continues blinking). In this case, disconnect the USB device cable at the Host (yellow LED stops blinking); and then try a different USB port as indicated by the Operating System message. You can now read codes. At this point you can read the USB interface configuration code according to your application. Load drivers from the O.S. (if requested). When configuring the USB-COM interface, the relevant files and drivers must be installed from the USB Device Installation software, which can be downloaded from the web page http://www.scanning.datalogic.com. The reader is ready to read barcodes. Successive start-ups will automatically recognize the previously loaded drivers. Connect QuickScan® Mobile to Host Select desired USB interface code (USB-KBD is default) Read test codes. Reader is READY Load drivers (if requested) Load drivers (if requested) Yellow LED blinks Yellow LED off – BEEP OK First Start-Up

the USB Device Installation software, which can be downloaded from the web site http://www.scanning.datalogic.com.

Once your reader is setup, you can change the default parameters to meet your application needs. Refer to the preceding paragraphs for initial configuration in order to set the default values and select the interface for your application. In this manual, the configuration parameters are divided into logical groups making it easy to find the desired function based on its reference group. The first five groups are for Standard/IBM Interface parameter configuration: RS-232 USB WEDGE (only for Quickscan M2 type:130) PEN EMULATION IBM 46xx (only for Quickscan M2 type:110) The following parameter groups are common to all interface applications: DATA FORMAT parameters regard the messages sent to the Host system for all interfaces except Pen Emulation. READING PARAMETERS control various operating modes and indicator status functioning. DECODING PARAMETERS maintain correct barcode decoding in certain special reading conditions. CODE SELECTION parameters allow configuration of a personalized mix of codes, code families and their options. ADVANCED FORMATTING PARAMETERS allow code concatenation and advanced formatting of messages towards the Host. It cannot be used with Pen Emulation connections. RADIO PARAMETERS (Mobile series only) allow configuration of radio control parameters.

� 1. Read the Enter Configuration code ONCE, available at the top of each page. 2. Read configuration codes from the desired groups. = Read the code and follow the procedure given � = Default value 3. Read the Exit and Save Configuration code ONCE, available at the top of each page.

Ì$+;Î RS-232 Ì$-?Î 21 BAUD RATE 300 baud ÌCD1XÎ 600 baud 1200 baud ÌCD2[Î ÌCD3^Î 2400 baud 4800 baud ÌCD4aÎ ÌCD5dÎ � 9600 baud 19200 baud ÌCD6gÎ ÌCD7jÎ 38400 baud ÌCD8mÎ

Ì$+;Î RS-232 Ì$-?Î 22 PARITY � none ÌCC0SÎ even parity ÌCC1VÎ odd parity ÌCC2YÎ DATA BITS 7 bits ÌCA0OÎ � 8 bits ÌCA1RÎ 9 bits ÌCA2UÎ

Ì$+;Î RS-232 Ì$-?Î 23 STOP BITS � 1 stop bit ÌCB0QÎ 2 stop bits ÌCB1TÎ HANDSHAKING � disable ÌCE0WÎ hardware (RTS/CTS) ÌCE1ZÎ software (XON/XOFF) ÌCE2]Î RTS always ON ÌCE3`Î See par. 4.1.1 for details.

Ì$+;Î RS-232 Ì$-?Î 24 ACK/NACK PROTOCOL � disable ÌER0sÎ enable ÌER1vÎ See par. 4.1.2 for details, particularly on implementing this parameter with QuickScan ® Mobile. FIFO disable ÌEC0UÎ � enable ÌEC1XÎ See par. 4.1.3 for details.

Ì$+;Î RS-232 Ì$-?Î 25 INTER-CHARACTER DELAY delay between characters transmitted to Host ÌCK3Î Read 2 numbers from the table where: 00 = DELAY disabled 01-99 = DELAY from 1 to 99 milliseconds � delay disabled RX TIMEOUT timeout control in reception from Host ÌCL5Î Read 2 numbers from the table where: 00 = TIMEOUT disabled 01-99 = TIMEOUT from .1 to 9.9 seconds � rx timeout 5 seconds See par. 4.1.4 for details.

Ì$+;Î RS-232 Ì$-?Î 26 SERIAL TRIGGER LOCK � disabled ÌCR0qÎ enable and select characters ÌCR1tÎ Read 2 characters from the Hex/Numeric table in the range 00-FE where: − First Character enables device trigger − Second Character inhibits device trigger until the first character is received again.

timeout, Serial trigger lock � � USB-KBD Keyboard nationality, FIFO, Inter-character delay, Inter-code delay, Control character emulation, USB keyboard speed � � USB-IBM No parameter selection required. � 1. Read the Enter Configuration code ONCE, available at the top of each page. 2. Read configuration codes from the desired groups. = Read the code and follow the procedure given � = Default value 3. Read the Exit and Save Configuration code ONCE, available at the top of each page.

Ì$+;Î USB-COM Ì$-?Î 28 HANDSHAKING � disable ÌCE0WÎ hardware (RTS/CTS) ÌCE1ZÎ software (XON/XOFF) ÌCE2]Î RTS always ON ÌCE3`Î See par. 4.1.1 for details. ACK/NACK PROTOCOL � disable ÌER0sÎ enable ÌER1vÎ See par. 4.1.2 for details.

Ì$+;Î USB-COM Ì$-?Î 29 FIFO disable ÌEC0UÎ � enable ÌEC1XÎ See par. 4.1.3 for details. INTER-CHARACTER DELAY delay between characters transmitted to Host ÌCK3Î Read 2 numbers from the table where: 00 = DELAY disabled 01-99 = DELAY from 1 to 99 milliseconds � delay disabled

Ì$+;Î USB-COM Ì$-?Î 30 RX TIMEOUT timeout control in reception from Host ÌCL5Î Read 2 numbers from the table where: 00 = TIMEOUT disabled 01-99 = TIMEOUT from .1 to 9.9 seconds � rx timeout 5 seconds See par. 4.1.4 for details. SERIAL TRIGGER LOCK � disabled ÌCR0qÎ enable and select characters ÌCR1tÎ Read 2 characters from the Hex/Numeric table in the range 00-FE where: − First Character enables device trigger − Second Character inhibits device trigger until the first character is received again.

Ì$+;Î USB-KBD Ì$-?Î 31 KEYBOARD NATIONALITY Not Available for USB-KBD-ALT-MODE Interface This parameter default value is restored through the Interface Selection code and not Restore Default. Belgian ÌFJ7yÎ English French ÌFJ4pÎ ÌFJ2jÎ German Italian ÌFJ3mÎ ÌFJ1gÎ Japanese Spanish ÌFJ8|Î ÌFJ6vÎ Swedish � USA ÌFJ5sÎ ÌFJ0dÎ

Ì$+;Î USB-KBD Ì$-?Î 32 FIFO disable ÌEC0UÎ � enable ÌEC1XÎ See par. 4.1.3 for details. INTER-CHARACTER DELAY delay between characters transmitted to Host ÌCK3Î Read 2 numbers from the table where: 00 = DELAY disabled 01-99 = DELAY from 1 to 99 milliseconds � delay disabled

Ì$+;Î USB-KBD Ì$-?Î 33 INTER-CODE DELAY delay between codes transmitted to Host ÌFG.Î Read 2 numbers from the table where: 00 = DELAY disabled 01-99 = DELAY from 1 to 99 seconds � delay disabled CONTROL CHARACTER EMULATION � CTRL + Shift + Key ÌFO0nÎ CTRL + Key ÌFO1qÎ

Ì$+;Î USB-KBD Ì$-?Î 34 USB KEYBOARD SPEED � Normal ÌUT10cÎ Fast ÌUT01dÎ

2. Read configuration codes from the desired groups. = Read the code and follow the procedure given � = Default value 3. Read the Exit and Save Configuration code ONCE, available at the top of each page. .

Ì$+;Î WEDGE Ì$-?Î 36 KEYBOARD NATIONALITY Belgian ÌFJ7yÎ English French ÌFJ4pÎ ÌFJ2jÎ German Italian ÌFJ3mÎ ÌFJ1gÎ Spanish Swedish ÌFJ6vÎ ÌFJ5sÎ � USA ÌFJ0dÎ The Japanese Keyboard Nationality selection is valid only for IBM AT compatible PCs. Japanese ÌFJ8|Î

Ì$+;Î WEDGE Ì$-?Î 37 CAPS LOCK � caps lock OFF ÌFE0ZÎ caps lock ON ÌFE1]Î Select the appropriate code to match your keyboard caps lock status. Note: Caps lock manual configuration is ignored when Caps Lock Auto-Recognition is enabled. For PC Notebook interface selections, the caps lock status is automatically recognized; therefore this command is not necessary. CAPS LOCK AUTO-RECOGNITION (IBM AT COMPATIBLE ONLY) disable ÌFP0pÎ � enable ÌFP1sÎ

Ì$+;Î WEDGE Ì$-?Î 38 NUM LOCK toggle num lock ÌFL1kÎ � num lock unchanged ÌFL0hÎ This selection is used together with the Alt Mode interface selection for AT or Notebook PCs. It changes the way the Alt Mode procedure is executed; therefore it should be set as follows: • if your keyboard Num Lock is normally on use num lock unchanged • if your keyboard Num Lock is normally off use toggle num lock In this way the device will execute the Alt Mode procedure correctly for your application. INTER-CHARACTER DELAY delay between characters transmitted to Host ÌCK3Î Read 2 numbers from the table where: 00 = DELAY disabled 01-99 = DELAY from 1 to 99 milliseconds � delay disabled

Ì$+;Î WEDGE Ì$-?Î 39 INTER-CODE DELAY delay between codes transmitted to Host ÌFG.Î Read 2 numbers from the table where: 00 = DELAY disabled 01-99 = DELAY from 1 to 99 seconds � delay disabled

Ì$+;Î WEDGE Ì$-?Î 40 KEYBOARD SETTING ALPHANUMERIC KEYBOARD SETTING The reader can be used with terminals or PCs with various keyboard types and nationalities through a simple keyboard setting procedure. The type of computer or terminal must be selected before activating the keyboard setting command. Keyboard setting consists of communicating to the reader how to send data corresponding to the keyboard used in the application. The keys must be set in a specific order. Press and release a key to set it. Some characters may require more than one key pressed simultaneously during normal use (refer to the manual of your PC or terminal for keyboard use). The exact sequence must be indicated to the reader in this case pressing and releasing the different keys. Example: If one has to press the "Shift" and "4" keys simultaneously on the keyboard to transmit the character "$" to the video, to set the "$", press and release "Shift" then press and release "4". Each pressed and released key must generate an acoustic signal on the reader, otherwise repress the key. Never press more than one key at the same time, even if this corresponds to the normal use of your keyboard. Press "Backspace" to correct a wrong key entry. In this case the reader emits 2 beeps. Note: "CAPS LOCK" and "NUM LOCK" must be off before starting the keyboard setting procedure. "SHIFT" must be repressed for each character and cannot be substituted by "CAPS LOCK". setting the alphanumeric keyboard ÌFB0TÎ Read the code above. Press the keys shown in the following table according to their numerical order. Some ASCII characters may be missing as this depends on the type of keyboard: these are generally particular characters relative to the various national symbologies. In this case: • The first 4 characters (Shift, Alt, Ctrl, and Backspace) can only be substituted with keys not used, or substituted with each other. • characters can be substituted with other single symbols (e.g. "SPACE") even if not included in the barcode set used. • characters can be substituted with others corresponding to your keyboard. The reader signals the end of the procedure with 2 beeps indicating the keys have been registered.

02 : Alt 03 : Ctrl 04 : Backspace 05 : SPACE 28 : 7 51 : N 06 : ! 29 : 8 52 : O 07 : " 30 : 9 53 : P 08 : # 31 : : 54 : Q 09 : $ 32 : ; 55 : R 10 : % 33 : < 56 : S 11 : & 34 : = 57 : T 12 : ' 35 : > 58 : U 13 : ( 36 : ? 59 : V 14 : ) 37 : @ 60 : W 15 : * 38 : A 61 : X 16 : + 39 : B 62 : Y 17 : , 40 : C 63 : Z 18 : - 41 : D 64 : [ 19 : . 42 : E 65 : \ 20 : / 43 : F 66 : ] 21 : 0 44 : G 67 : ^ 22 : 1 45 : H 68 : _ (underscore) 23 : 2 46 : I 69 : ` 24 : 3 47 : J 70 : { 25 : 4 48 : K 71 : | 26 : 5 49 : L 72 : } 27 : 6 50 : M 73 : ~ 74 : DEL The keyboard setup functioning is signaled by the LEDs on the cradle. Each key stroke corresponds to a double blinking of the yellow LED. By pressing the Backspace key the red LED on the cradle blinks, while the yellow LED stays on. CAUTION Do not place the reader onto the cradle during this procedure. Otherwise, the battery charging will occur modifying the LEDs functioning. Once the procedure has been completed, the yellow LED turns off.

Ì$+;Î WEDGE Ì$-?Î 42 CONTROL CHARACTER EMULATION � CTRL + Shift + Key ÌFO0nÎ CTRL + Key ÌFO1qÎ

� � CONVERSION TO CODE 39 � � OVERFLOW � � OUTPUT LEVEL � � IDLE LEVEL � � INTER-BLOCK DELAY � 1. Read the Enter Configuration code ONCE, available at the top of each page. 2. Read configuration codes from the desired groups. � = Default value 3. Read the Exit and Save Configuration code ONCE, available at the top of each page.

Enter and Exit configuration codes. OPERATING MODE � interpret mode Ì$]8Î Interprets commands without sending them to the decoder. transparent mode Ì$[4Î Sends commands to the decoder without interpreting them.

Ì$+;Î PEN EMULATION Ì$-?Î 45 MINIMUM OUTPUT PULSE 200 μs ÌDG0\Î 400 μs � 600 μs ÌDG1_Î ÌDG2bÎ 800 μs 1 ms ÌDG3eÎ ÌDG4hÎ 1.2 ms low resolution code emulation high resolution code emulation ÌDG5kÎ See par. 4.2.1 for details.

Ì$+;Î PEN EMULATION Ì$-?Î 46 CONVERSION TO CODE 39 AND CODE 128 disable conversion to Code 39 ÌDA0PÎ Transmits codes in their original format. enable conversion to Code 39 ÌDA1SÎ Converts codes read into Code 39 format. enable conversion to Code 128 ÌDA2VÎ Converts codes read into Code 128 format. See par. 4.2.2 for details.

Ì$+;Î PEN EMULATION Ì$-?Î 47 OVERFLOW narrow ÌDH0^Î � medium ÌDH1aÎ wide ÌDH2dÎ See par. 4.2.3 for details. OUTPUT LEVEL � normal (white = logic level 0) ÌDD0VÎ inverted (white = logic level 1) ÌDD1YÎ See par. 4.2.4 for details.

Ì$+;Î PEN EMULATION Ì$-?Î 48 IDLE LEVEL � normal (black level) ÌDE0XÎ inverted (white level) ÌDE1[Î See par. 4.2.4 for details. INTER-BLOCK DELAY delay between character blocks transmitted to Host ÌCK3Î Read 2 numbers from the table where: 00 = DELAY disabled 01-99 = DELAY from .1 to 9.9 seconds � delay disabled See par. 4.2.5 for details.

� 1. Read the Enter Configuration code ONCE, available at the top of each page. 2. Read configuration codes from the desired groups. � = Default value 3. Read the Exit and Save Configuration code ONCE, available at the top of each page.

Ì$+;Î IBM 46xx Ì$-?Î 50 IBM DATA FORMATTING conversion to Code 39 ÌGD0YÎ � IBM Standard ÌGD1\Î mixed IBM Standard + Code 39 ÌGD2_Î � Cradle check the Host command ÌGE0[Î Cradle ignore Host command ÌGE1^Î See par. 4.3.1 for details.

� CODE IDENTIFIER � � CUSTOM CODE IDENTIFIER � � HEADER � � TERMINATOR � � SPECIAL KEYS � � FIELD ADJUSTMENT � � FIELD ADJ. CHARACTER � � CODE LENGTH TX � � CHARACTER REPLACEMENT � � ADDRESS STAMPING � � ADDRESS DELIMITER � 1. Read the Enter Configuration code ONCE, available at the top of each page. 2. Read configuration codes from the desired groups. = Read the code and follow the procedure given � = Default value 3. Read the Exit and Save Configuration code ONCE, available at the top of each page.

CODE AIM STANDARD DATALOGIC STANDARD Custom 2/5 interleaved ] I y N 2/5 industrial ] X y P 2/5 normal 5 bars ] S y O 2/5 matrix 3 bars ] X y Q EAN 8 ] E 4 A EAN 13 ] E 0 B UPC A ] X y C UPC E ] X y D EAN 8 with 2 ADD ON ] E 5 J EAN 8 with 5 ADD ON ] E 6 K EAN 13 with 2 ADD ON ] E 1 L EAN 13 with 5 ADD ON ] E 2 M UPC A with 2 ADD ON ] X y F UPC A with 5 ADD ON ] X y G UPC E with 2 ADD ON ] X y H UPC E with 5 ADD ON ] X y I Code 39 ] A y V Code 39 Full ASCII ] A y W CODABAR ] F y R ABC CODABAR ] X y S Code 128 ] C y T EAN 128 ] C y k ISBT 128 ] C4 f Code 93 ] G y U CIP/39 ] X y Y CIP/HR ] X y e Code 32 ] X y X MSI ] M y Z Plessey Standard ] P 0 a Plessey Anker ] P 1 o Telepen ] X 0 d Delta IBM ] X 0 c Code 11 ] H y b Code 16K ] K 0 p Code 49 ] T y q RSS Expanded Linear and Stacked ] e 0 t RSS Limited ] e 0 v RSS 14 Linear and Stacked ] e 0 u

code for which the standard is not defined. The y value depends on the selected options (check digit tested or not, check digit tx or not, etc.). • When customizing the Datalogic Standard code identifiers, 1 or 2 identifier characters can be defined for each code type. If only 1 identifier character is required, the second character must be selected as FF (disabled). • The code identifier can be singly disabled for any code by simply selecting FF as the first identifier character. • Write in the Custom character identifiers in the table above for your records.

Ì$+;Î DATA FORMAT Ì$-?Î 54 CODE IDENTIFIER � disable ÌEB0SÎ Datalogic standard ÌEB1VÎ AIM standard ÌEB2YÎ custom ÌEB3\Î

Ì$+;Î DATA FORMAT Ì$-?Î 55 CUSTOM CODE IDENTIFIER define custom code identifier(s) ÌEH/Î � Read the above code. (Code Identifiers default to Datalogic standard, see table on previous page). � Select the code type from the code table in Appendix B for the identifier you want to change. � You can define 1 or 2 identifier characters for each code type. If only 1 identifier character is required, the second character must be selected as FF (disabled). Read the hexadecimal value corresponding to the character(s) you want to define as identifiers for the code selected in step �: valid characters are in the range 00-FD. For Wedge and USB-KBD interfaces, it is also possible to read the Special Key(s) on page 58. Example: To define Code 39 Code Identifier = @ define custom code identifier(s) Code 39 Read ÌEH/Î + ÌVWÎ + 40 + FF

Ì$+;Î DATA FORMAT Ì$-?Î 56 HEADER no header ÌEA00*Î one character header two character header ÌEA01.Î ÌEA022Î three character header four character header ÌEA036Î ÌEA04:Î five character header six character header ÌEA05>Î ÌEA06BÎ seven character header eight character header ÌEA07FÎ ÌEA08JÎ After selecting one of the desired Header codes, read the character(s) from the HEX table. Valid characters are in the range 00-FE. For Wedge and USB-KBD interfaces, it is also possible to read the Special Key(s) on page 58. Example: four character header + 41 + 42 + 43 + 44 = Header ABCD For more details see par. 4.4.1.

Ì$+;Î DATA FORMAT Ì$-?Î 57 TERMINATOR no terminator ÌEA10-Î one character terminator two character terminator ÌEA111Î ÌEA125Î three character terminator four character terminator ÌEA139Î ÌEA14=Î five character terminator six character terminator ÌEA15AÎ ÌEA16EÎ seven character terminator eight character terminator ÌEA17IÎ ÌEA18MÎ After selecting one of the desired Header codes, read the character(s) from the HEX table. Valid characters are in the range 00-FE. For Wedge and USB-KBD interfaces, it is also possible to read the Special Key(s) on page 58. Example: two character terminator + 0D + 0A = Terminator CR LF For more details see par. 4.4.1.

Ì$+;Î DATA FORMAT Ì$-?Î 58 SPECIAL KEYS Available only for Wedge IBM AT-PS/2 and USB-KBD Interfaces NOTE It is necessary to define each Special Key by following the procedure given in par. 4.4.2. Select one or more of the following Special Keys according to your needs. Special Key 1 Ì9CÄÎ Special Key 2 Special Key 3 Ì9DÆÎ Ì9EÈÎ Special Key 4 Special Key 5 Ì9FÊÎ ÌA0bÎ

Ì$+;Î DATA FORMAT Ì$-?Î 59 FIELD ADJUSTMENT � disable field adjustment ÌEF0[Î Field adjustment allows a number of characters n, to be added to or subtracted from the barcode read. The adjustment can be different for each enabled code type. To define the field adjustment: � Read the enable field adjustment code: enable field adjustment ÌEF+Î � Select the code type from the Code Identifier Table in Appendix B. � Select the type of adjustment to perform: right addition Ì01Î left addition right deletion Ì12Î Ì23Î left deletion Ì34Î � Read a number in the range 01 - 32 from the Hex/Numeric Table to define how many characters to add or delete: Conditions: • Adjustment is only performed on the barcode data; the Code Identifier and Code Length Transmission fields are not modified by the field adjustment parameter. • If the field setting would subtract more characters than exist in the barcode, the subtraction will take place only to code length 0. • You can set up to a maximum of 10 different field adjustments on the same barcode family or on different barcode families. Example: To add 4 characters to the right of Standard Code 39 Codes: enable field adjustment Code 39 right addition Read ÌEF+Î + ÌVWÎ + Ì01Î + 04

Ì$+;Î DATA FORMAT Ì$-?Î 60 FIELD ADJUSTMENT CHARACTER � Read the field adjustment character code: field adjustment character ÌEG-Î � Read the hexadecimal value corresponding to the character you want to use for field adjustment. Valid characters are in the range 00-FE. For Wedge and USB-KBD interfaces, it is also possible to read the Special Key(s) on page 58. Example: To define the field adjustment character = A: Read field adjustment character + 41 CODE LENGTH TX � code length not transmitted ÌEE0YÎ code length transmitted in variable-digit format ÌEE1\Î code length transmitted in fixed 4-digit format ÌEE2_Î The code length is transmitted in the message after the Headers and Code Identifier characters. The code length is calculated after performing any field adjustment operations.

Ì$+;Î DATA FORMAT Ì$-?Î 61 CHARACTER REPLACEMENT � disable character replacement ÌEO0mÎ This parameter allows up to three characters to be replaced from the barcode read. These substitutions are stored in memory. To define each character replacement: � Read one of the following character replacement codes: first character replacement ÌEO1pÎ second character replacement ÌEO2sÎ third character replacement ÌEO3vÎ � From the Code Identifier Table in Appendix B, read the Code Identifier for the desired code family. 0 = character replacement will be effective for all code families. � From the Hex/Numeric Table read two characters corresponding to the Hex value (00-FE) which identifies the character to be replaced. For Wedge and USB-KBD interfaces, it is also possible to read the Special Key(s) on page 58. � From the Hex/Numeric Table read two characters corresponding to the Hex value (00-FE) which identifies the new character to replace. For Wedge and USB-KBD interfaces, it is also possible to read the Special Key(s) on page 58. FF = the character to be replaced will be substituted with no character, that is, it will be removed from the code.

1. First Character Replacement: substitution in Code 39 barcodes of all occurrences of the 0 character with the 1 character. 2. Second Character Replacement: substitution in Code 39 barcodes of all occurrences of the A character with the B character. first character replacement Code 39 ASCII characters corresponding to the HEX value for character 0 ASCII characters corresponding to the HEX value for character 1 ÌEO1pÎ + ÌVWÎ + 30 + 31 For Code 39 codes containing the string "0123", the contents transmitted will be "1123". second character replacement Code 39 ASCII characters corresponding to the HEX value for character A ASCII characters corresponding to the HEX value for character B ÌEO2sÎ + ÌVWÎ + 41 + 42 For Code 39 codes containing the string "ABCD", the contents transmitted will be "BBCD".

Ì$+;Î DATA FORMAT Ì$-?Î 63 ADDRESS STAMPING � disable reader address stamping ÌRU0ÊÎ enable reader address stamping ÌRU1"Î See par. 4.4.3 for details. ADDRESS DELIMITER � disable reader address delimiter ÌRV0!Î enable reader address delimiter and select characters ÌRV1$Î Read 2 HEX characters in the range 00-FE. See par. 4.4.4 for details.

� � TRIGGER-OFF TIMEOUT � � FLASH MODE � � READS PER CYCLE � � SAFETY TIME � � BEEPER INTENSITY � � BEEPER TONE � � BEEPER TYPE � � BEEPER LENGTH � � STAND RECOGNITION BEEP � 1. Read the Enter Configuration code ONCE, available at the top of each page. 2. Read configuration codes from the desired groups. = Read the code and follow the procedure given � = Default value 3. Read the Exit and Save Configuration code ONCE, available at the top of each page.

Ì$+;Î READING PARAMETERS Ì$-?Î 65 HAND-HELD OPERATION � hardware trigger ÌBK1eÎ software trigger * always on ÌBK0bÎ ÌBK3kÎ * not available for Mobile series readers automatic hardware trigger ready ÌBK2hÎ ÌBK4nÎ STAND OPERATION ONLY Devices with Stand Recognition Beep hardware trigger ÌBU3ÃÎ software trigger * always on ÌBU1yÎ ÌBU2|Î * not available for Mobile series readers � automatic ÌBU0vÎ

Ì$+;Î READING PARAMETERS Ì$-?Î 66 HARDWARE TRIGGER MODE � trigger active level ÌBA0NÎ trigger active pulse ÌBA1QÎ See par. 4.5.1 for details TRIGGER-OFF TIMEOUT trigger-off timeout ÌBD$Î Read 2 numbers in the range 00-99: 00 = disables the trigger-off timeout 01-99 = corresponds to a max. 99-sec. delay after the trigger press to allow the reader to turn off automatically. � trigger-off timeout disabled See par. 4.5.2 for details.

Ì$+;Î READING PARAMETERS Ì$-?Î 67 FLASH MODE "FLASH" ON duration ÌBB0PÎ "FLASH" OFF duration ÌBB1SÎ Read 2 numbers in the range 01-99: 01 to 99 = from .1 to 9.9 seconds. � Flash-ON = 1 sec. Flash-OFF = 0.6 sec READS PER CYCLE � one read per cycle ÌBC0RÎ multiple reads per cycle ÌBC1UÎ See par. 4.5.3 for details.

Ì$+;Î READING PARAMETERS Ì$-?Î 68 SAFETY TIME safety time ÌBE&Î Limits same code consecutive reading. Read 2 numbers in the range 00-99: 00 = no same code consecutive reading until reader is removed (no decoding) for at least 400 ms. 01-99 = timeout from .1 to 9.9 seconds before a consecutive read on same code. � safety time = 0.5 sec See par. 4.5.4 for details. BEEPER INTENSITY * very low intensity ÌBG0ZÎ low intensity medium intensity ÌBG1]Î ÌBG2`Î � high intensity ÌBG3cÎ * This sets the beeper OFF for data entry, while for all other beeper signals it has the meaning “very low intensity”. The Beeper Intensity parameter is effective for all operating conditions described in par. 5.2.

Ì$+;Î READING PARAMETERS Ì$-?Î 69 BEEPER TONE tone 1 ÌBH0\Î � tone 2 tone 3 ÌBH1_Î ÌBH2bÎ tone 4 ÌBH3eÎ BEEPER TYPE � monotone ÌBJ0`Î bitonal ÌBJ1cÎ BEEPER LENGTH long ÌBI0^Î � short ÌBI1aÎ

Ì$+;Î READING PARAMETERS Ì$-?Î 70 STAND RECOGNITION BEEP ONLY Devices with Stand Recognition disable ÌBV0xÎ � enable ÌBV1{Î

par. 4.6. 1. Read the Enter Configuration code ONCE, available at the top of each page. 2. Read configuration codes from the desired groups. � = Default value 3. Read the Exit and Save Configuration code ONCE, available at the top of each page.

Ì$+;Î DECODING PARAMETERS Ì$-?Î 72 INK SPREAD disable ÌAX0{Î � enable ÌAX1~Î See par. 4.6.1 for details. OVERFLOW CONTROL disable ÌAW1|Î � enable ÌAW0yÎ See par. 4.6.2 for details.

Ì$+;Î DECODING PARAMETERS Ì$-?Î 73 INTERDIGIT CONTROL disable ÌAV0wÎ � enable ÌAV1zÎ See par. 4.6.3 for details. DECODING SAFETY � one read ÌED0WÎ (decoding safety disabled) two reads three reads ÌED1ZÎ ÌED2]Î four reads ÌED3`Î Required number of good reads before accepting code.

Ì$+;Î DECODING PARAMETERS Ì$-?Î 74 PUZZLE SOLVER™ � disable ÌAU0uÎ enable ÌAU1xÎ In the case of damaged or poorly printed codes, this parameter allows reading multiple parts of the single code to reconstruct it. To read codes using this technology, simply move the illuminated bar over the code so that each line of the code is scanned. During this process a series of brief “ticks” indicates that reading is proceeding correctly. Conditions: • This parameter is only valid for the following codes: EAN 8 without Add-on EAN 13 without Add-on UPC A without Add-on Code 128 Code 39 • For Code 39, Check digit control is forced. • PuzzleSolver™ is not valid for ISBT 128 code.

� � CODE 128 FAMILY � � CODABAR FAMILY � � CODE 93 � � MSI � � PLESSEY � � TELEPEN � � DELTA IBM � � CODE 11 � � CODE 16K � � CODE 49 � � GS1 DATABAR™ � 1. Read the Enter Configuration code ONCE, available at the top of each page. 2. Read configuration codes from the desired groups. = Read the code and follow the procedure given � = Default value 3. Read the Exit and Save Configuration code ONCE, available at the top of each page.

Ì$+;Î CODE SELECTION Ì$-?Î 76 DISABLE ALL CODE FAMILIES ÌAZ0ÃÎ NOTE The reader allows up to 5 code selections. This does not limit the number of CODES enabled to 5, as it depends on the code family. SINGLE SELECTIONS = Example 5 code selections: 1. 2/5 Interleaved 2. 2/5 Industrial 3. Code 128 + EAN 128 4. Code 39 Full ASCII + Code 32 5. UPC A/UPC E In this section all SINGLE code selections are underlined and in bold. • ONE combination code from the EAN family • ONE code from the 2/5 family

Ì$+;Î CODE SELECTION Ì$-?Î 77 EAN/UPC FAMILY disable the family ÌAA0MÎ � Read the desired family code Note: Since the EAN/UPC without ADD ON code selection is enabled by default, to correctly enable another selection, first disable the family. WITHOUT ADD ON � EAN 8/EAN 13/UPC A/UPC E ÌAA1PÎ EAN 8/EAN 13 ÌAA3VÎ UPC A/UPC E ÌAA4YÎ

Ì$+;Î CODE SELECTION Ì$-?Î 78 WITH ADD ON 2 AND 5 EAN 8/EAN 13/UPC A/UPC E ÌAA5\Î EAN 8/EAN 13 ÌAA6_Î UPC A/UPC E ÌAA7bÎ WITH ADD ON 2 ONLY EAN 8/EAN 13 ÌAAK7Î UPC A/UPC E ÌAAM=Î WITH ADD ON 5 ONLY EAN 8/EAN 13 ÌAAL:Î UPC A/UPC E ÌAAN@Î

Ì$+;Î CODE SELECTION Ì$-?Î 79 WITH AND WITHOUT ADD ON � EAN/UPC with and without ADD ON no Autodiscrimination ÌAA8Ad03Î EAN/UPC Autodiscrimination ADD ON by Prefix ÌAA8Ad19Î By setting the EAN/UPC Autodiscrimination ADD ON by Prefix, the desired prefixes must be selected by reading the corresponding codes given in the following section, since no prefix is configured by default.

Ì$+;Î CODE SELECTION Ì$-?Î 80 SELECT EAN/UPC PREFIXES NOTE When scanning the following codes, barcodes starting with the selected prefixes will be read and transmitted only if the ADD ON is present. If no ADD ON is found, the barcode will not be read. Barcodes starting with different characters are read regardless of ADD ON presence and transmitted always without ADD ON. � Cancel All Selections ÌET0wÎ OR select one or more of the following prefixes: 378/379 ÌET1378ET2379PÎ 434/439 ÌET3434ET4439ÉÎ 414/419 ÌET5414ET6419}Î 977 ÌET7977QÎ 978 ÌET8978ZÎ 979 ÌET9979cÎ The commands above are not mutually exclusive. They can be used to configure more than one set of prefixes simultaneously.

Ì$+;Î CODE SELECTION Ì$-?Î 81 Example: The following string allows reading and transmitting with ADD ON all EAN/UPC starting with the 434/439, 977 and 978 prefixes: 1. EAN/UPC Autodiscrimination ADD ON by Prefix. 2. 434/439: enables reading and transmission with ADD ON of all EAN/UPC barcodes starting with 434/439 prefixes. 3. 977: enables reading and transmission with ADD ON of all EAN/UPC barcodes starting with 977 prefix. 4. 978: enables reading and transmission with ADD ON of all EAN/UPC barcodes starting with 978 prefix. EAN/UPC Autodiscrimination ADD ON by Prefix 434/439 ÌAA8Ad19Î + ÌET3434ET4439ÉÎ + 977 978 + ÌET7977QÎ + ÌET8978ZÎ To clear the current prefix selections: 1. Cancel all Selections Cancel All Selections ÌET0wÎ

Ì$+;Î CODE SELECTION Ì$-?Î 82 EAN/UPC CHECK DIGIT TX SELECTIONS For each code type in this family you can choose to transmit the check digit or not CHECK DIGIT TRANSMISSION � EAN 8 NO CHECK DIGIT TRANSMISSION ÌAAG1oÎ EAN 8 ÌAAG0kÎ � EAN 13 ÌAAH1rÎ EAN 13 ÌAAH0nÎ � UPC A ÌAAI1uÎ UPC A ÌAAI0qÎ � UPC E ÌAAJ1xÎ UPC E ÌAAJ0tÎ

Ì$+;Î CODE SELECTION Ì$-?Î 83 CONVERSION OPTIONS UPC E to UPC A conversion ÌAAAÄÎ UPC E to EAN 13 conversion ÌAABÇÎ UPC A to EAN 13 conversion ÌAACÊÎ EAN 8 to EAN 13 conversion ÌAAD"Î Enable only ISBN conversion ÌAP1nÎ Enable only ISSN conversion ÌAP2qÎ Enable both ISBN and ISSN conversion ÌAP3tÎ Disable both ISBN and ISSN conversion ÌAP0kÎ

Ì$+;Î CODE SELECTION Ì$-?Î 84 2/5 FAMILY disable the family ÌAC0QÎ � Read the desired family code � Read a check digit selection � Interleaved 2/5 ÌAC1TÎ CHECK DIGIT TABLE no check digit control Normal 2/5 (5 Bars) Ì12Î ÌAC2WÎ � check digit control and transmission Industrial 2/5 (IATA) Ì23Î ÌAC3ZÎ check digit control without transmission Matrix 2/5 (3 Bars) Ì34Î ÌAC4]Î � Read 4 numbers for the code length where: − First 2 digits = minimum code length. − Second 2 digits = maximum code length. The pharmaceutical code below is part of the 2/5 family but has no check digit or code length selections. Code CIP/HR The maximum code length is 99 characters. The minimum code length must always be less than or equal to the maximum. ÌAC5`Î French pharmaceutical code Examples: 0199 = variable from 1 to 99 digits in the code. 1010 = 10 digit code length only.

Ì$+;Î CODE SELECTION Ì$-?Î 85 CODE 39 FAMILY disables the family ÌAB0OÎ � Read the desired family code � Read a check digit selection � Standard Code 39 CHECK DIGIT TABLE � no check digit control ÌAB1RÎ Ì12Î Full ASCII Code 39 check digit control and transmission ÌAB2UÎ Ì23Î check digit control without transmission Ì34Î

Ì$+;Î CODE SELECTION Ì$-?Î 86 The pharmaceutical codes below are part of the Code 39 family but have no check digit selections. Code CIP39 ÌAB3XÎ French pharmaceutical code Code 32 ÌAB4[Î Italian pharmaceutical code CODE LENGTH (optional) The code length selection is valid for the entire Code 39 family Read the code + 4 numbers for the code length where: set code length First 2 digits = minimum code length. Second 2 digits = maximum code length. ÌAB*=Î The maximum code length is 99 characters. The minimum code length must always be less than or equal to the maximum. Examples: 0199 = variable from 1 to 99 digits in the code. 1010 = 10 digit code length only.

Ì$+;Î CODE SELECTION Ì$-?Î 87 CODE 128 FAMILY disables the family ÌAI0]Î � Read the desired family code � Code 128 ÌAI11=Î control without transmission of check digit EAN 128 ÌAI21@Î control without transmission of check digit Transmit GS Before Code Code EAN 128 uses the ASCII character to separate a variable length code field from the next code field. This character can also be transmitted before the code. � disable ÌEQ0qÎ enable ÌEQ1tÎ If the character has been modified in the Character Replacement parameter, the new character is affected by this command.

Ì$+;Î CODE SELECTION Ì$-?Î 88 ISBT 128 ÌAI31CÎ Enabling ISBT 128 automatically disables Puzzle Solver™. CODE LENGTH (optional) The code length selection is valid for the entire Code 128 family. Read the code + 4 numbers for the code length where: First 2 digits = minimum code length Second 2 digits = maximum code length set code length ÌAILJÎ The maximum code length is 99 characters. The minimum code length must always be less than or equal to the maximum. Examples: 0199 = variable from 1 to 99 digits in the code. 1010= 10 digit code length only. The length is calculated on the output string. CODE 93 � disables the code ÌAK0aÎ Code 93 ÌAK1dÎ control without transmission of check digit

Ì$+;Î CODE SELECTION Ì$-?Î 89 CODABAR FAMILY � disable the family ÌAD0SÎ � Read the desired equality control code � Read a start/stop transmission selection START/STOP CHARACTER TRANSMISSION Standard Codabar ÌAD113Î no start/stop character equality control no transmission Ì12Î Standard Codabar ÌAD127Î start/stop character equality control transmission Ì23Î The Codabar ABC code below uses a fixed start/stop character transmission selection. Codabar ABC ÌAD212)Î no start/stop character equality control but transmission.

Ì$+;Î CODE SELECTION Ì$-?Î 90 Codabar ABC Forced Concatenation enable Codabar ABC with forced concatenation ÌAD2321Î non start/stop character equality control but transmission CODE LENGTH (optional) The code length selection is valid for the entire Codabar family Read the code + 4 numbers for the code length where: set code length First 2 digits = minimum code length. Second 2 digits = maximum code length. ÌAD*AÎ The maximum code length is 99 characters. The minimum code length must always be less than or equal to the maximum. Examples: 0199 = variable from 1 to 99 digits in the code. 1010 = 10 digit code length only. START/STOP CHARACTER CASE IN TRANSMISSION The start/stop character case selections below are valid for the entire Codabar family: transmit start/stop characters in lower case ÌADA0_Î transmit start/stop characters in upper case ÌADA1cÎ

Ì$+;Î CODE SELECTION Ì$-?Î 91 MSI � disable the family ÌAE0UÎ Enable the code by selecting one of the check digit selections. no check digit control ÌAE1XÎ MOD10 check digit control no check digit transmission ÌAE2[Î MOD10 check digit control check digit transmission ÌAE3^Î MOD11 - MOD10 check digit control no check digit transmission ÌAE4aÎ MOD11 - MOD10 check digit control check digit transmission ÌAE5dÎ MOD10 - MOD10 check digit control no check digit transmission ÌAE6gÎ MOD10 - MOD10 check digit control check digit transmission ÌAE7jÎ

Ì$+;Î CODE SELECTION Ì$-?Î 92 PLESSEY � disable the family ÌAF0WÎ Enable the code by selecting one of the check digit selections. Standard Plessey no check digit control ÌAF117Î check digit control check digit transmitted ÌAF12;Î check digit control check digit not transmitted ÌAF13?Î Anker Plessey no check digit control ÌAF21:Î check digit control check digit transmitted ÌAF22>Î check digit control check digit not transmitted ÌAF23BÎ

Ì$+;Î CODE SELECTION Ì$-?Î 93 TELEPEN � disable the family ÌAL0cÎ Enable the code by selecting one of the check digit selections. Numeric Telepen no check digit control ÌAL11CÎ check digit control check digit transmitted ÌAL12GÎ check digit control check digit not transmitted ÌAL13KÎ Alphanumeric Telepen no check digit control ÌAL21FÎ check digit control check digit transmitted ÌAL22JÎ check digit control check digit not transmitted ÌAL23NÎ

Ì$+;Î CODE SELECTION Ì$-?Î 94 DELTA IBM � disable the family ÌAH0[Î Enable the code by selecting one of the check digit selections. no check digit control ÌAH1^Î Type 1 check digit control ÌAH2aÎ Type 2 check digit control ÌAH3dÎ