Artec Mini Tracker 505 Operation & User’s Manual

will corrode electronic circuits. If your device does get wet, remove the battery, and allow the device to dry completely before replacing it. (b) Do not use or store the device in dusty, dirty areas. Its moving parts and lectronic components can be damaged. (c) Do not store the device in hot areas. High temperatures can shorten the life of electronic devices, damage batteries, and warp or melt certain plastics. (d) Do not store the device in cold areas. When the device returns to its normal temperature, moisture can form inside the device and damage electronic circuit boards. (e) Do not put Master and Slave at same place in case of this set is unable playing functions to guard your valued goods. (f) This product only assists to provide the warning alarm for reminding the user. It does not guarantee to prevent steal or rob by personal safety and property if any urgent need. This product does not guarantee any damage of personal safety, property, material or the information loss, or other related loss. (g) We reserve the right in changing the specification of the hardware and software designs to manuals at any time and without prior notice. Informationin this document is subject to change without notice. (h) This product operational temperature is between 0 °C ~ +55 °C. Storage temperature is between -10 °C~ +60 °C. Warning: Do not put the battery into the fire or heat resource. It will be cause dangerous or even explosion. (a) Do not attempt to open the device other than instructed in this guide. (b) Do not drop, knock, or shake the device. Rough handling can break internal circuit boards and fine mechanics. (c) Do not use harsh chemicals, cleaning solvents, or strong detergents to clean the device. (d) Do not paint the device. Paint can clog the moving parts and prevent proper operation. Warning 1 Care and Maintenance Caution

Please contact with local recycle department for detail. 2 FCC Certifications Federal Communication Commission Interference Statement This equipment has been tested and improved to comply with the limits of a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy, if installed and used not in accordance with the instructions, may cause harmful interference to radio communications. However,there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:  Reorient or relocate the receiving antenna.  Increase the separation between the equipment and receiver.  Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.  Consult the dealer or an experienced radio/TV technician for help. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1)This device may not cause harmful interference, and (2)this device must accept an interference received, including interference that may cause undesired operation. FCC Caution: Any changes or modifications are not expressly approved by the party responsible for compliance which could void the user's authority to operate this equipment. FCC ID Master: WMPM05A01 Slave: WMPS05A01 EU Declaration Conformity This product is carrying the CE-Mark in accordance with the related European Directives. Care and Maintenance (e) The working range, alarm range, searching and detection are depends the terrain environment because of radio wave efficiency. (f) If the beeps sound are not loud enough, it may means the battery low. Change new battery for louder alarm sound. (g) If you want to apply this product during the flight trip, please comply with the flight safety law according to each country.

Mute distance melody button at search mode Hanging hole for strap Clip Overview

19×28×7.5 mm 8~16m Alarm Trident Direction ZZZZ Sleeping Mode Master 39×48×6.8 mm Frequency Battery LR 44 × 2 Switch 2 buttons Size Slave ON / OFF / MUTE Button 4 No Alarm Working Method Specification Base on open frame condition. 0~80m

1 2 3 1 1. Open from the fillister on the bottom of housing or curve side by your nail, like open shell. 2. Put 2pcs batteries into. *** Make sure the installment direction of positive (+) & negative (-) of battery are followed up the drawing showed on the inside of back battery cover. 3. Set back the battery cover. Slave 1. Press the clip on battery cover then push backwardly. 2. Put 2pcs batteries into. *** Make sure the installment direction of positive (+) & negative (-) of battery are followed up the drawing showed on battery cover. 3. Set the battery cover back.

battery installment . Switch to power on Pull out Plastic isolation Place two devices no more than 10 cm apart. Signal indication Signal LED ON for re-linking. Distance indication Beep Re-link successful! Master shows the distance with Slave via LED and melody (beep). Press Search button to stop melody. 1 2 5 3 4 Beep If Master can't link with Slave, it will beep once every few seconds. Caution

2~3 seconds Start to detect the location of Slave. Near Far 7 Correct holding Wrong holding Error indication - whole direction LED goes off but signal LED lights up 3 seconds then displays new searched distance. 1.) Search from correct direction to wrong direction 2.) Over pass 1.) LED light: more closer, more lights. 2.) Search melody: more closer, more rapid.

3 Distance LEDs. The strongest signal direction ! Turn to different directions for signal comparison One Distance LED only 2 Distance LEDs 8 1 2 Go the way of the strongest signal direction to find out Slave.

from Slave to assist short range searching. Press & hold the LED light button Stop the melody Listen to the beep sound from Slave Beep 2 2

Signal LED flashes every second for re-linking Signal indication Press Search button 2~3 seconds Error indication - whole direction LED goes off but signal LED lights up 3 seconds then displays new searched distance. 1.) Search from correct direction to wrong direction 2.) Over pass

Signal indication Distance LED goes out all lights suddenly and only flash Signal LED with beep sound LED displays new searched distance Go back to original search direction or location 4 2 1 3 Location: North Go to the wrong direction Original searching (Right direction) [Suggestion] 3 seconds later Searching Example

Come with beep! Stop alarm (beep) if both devices comes within 8 meter again. Signal indication When Slave and Master are over 100 meter or lose signal Caution Slave flashes half minute to wait for re-linking No linking then into sleeping modeand stop flash 12

13 Sleeping Under Standby mode Stop signal to Slave No linking then into sleeping mode and stop flash Slave flashes half minute to wait for re-linking 2 1 Switch the button to section 0 (OFF)

section 1 (ON) Signal LED ON for re-linking Available for distance within 80 meter Re-link successful! Master shows the distance between Slave via LED and melody (beep) Distance indication Signal indication Beep Beep 1 2 Beep Can't get signal from Slave. Signal LED flashes each second & comes with beep. (Slave maybe out of working range 100 meter, or no power.) Re-link / Wake up

Service) 1 2 Switch the button to section 2 (MUTE) 3 Only Display the distance indication LED without searching melody Under Standby mode Switch to Mute mode Press Search button Under mute mode, the Alarm function is disabled. 15

abnormal display to alarm, beeps or non-working to confuse actual working stage. Please change new battery as soon as possible. 16 1 beep sound every 120 seconds continuously.

Wrong holding Correct holding Correct holding Wrong holding 90 < 90 17 *** Do not cover the top side of Master.